Coagulation of micro-polluted Pearl River water with IPF-PACls

IntroductionThewaterqualityofnaturalriverisverycomplex,includingvariouskindsoforganic ,inorganicandbiologicalmatters,suchasthesolublemolecules,polymericmatters,colloids ,andsuspendedparticlessuchaslivebacteria ,algaeandalsoprotozoan (Tang,2 0 0 0 ) .Generally ,aquaticparticulatesaredispersivelysuspended ,ordepositintodiversesedimentsthroughadsorption ,aggregationandsedimentation.Furthermore ,theycanberesuspended ,transferredandconvertedundervariouswaterfluidconditions.Clearlydocumentedhistori…     

Prediction of DOM removal of low specific UV absorbance surface waters using HPSEC combined with peak fitting

High performance size exclusion chromatography (HPSEC) is used in water quality research primarily to determine the molecular weight distribution of the dissolved organic matter (DOM), but by applying peak fitting to the chromatogram, this technique can also be used as a tool to model and predict DOM removal. Six low specific UV absorbance (SUVA) source waters were treated using coagulation with alum and both the source and treated water samples were analysed using HPSEC. By comparing the molecular weight profiles of the source and treated waters, it was established that several DOM components were not effectively removed by alum coagulation even after high dosage alum treatment. A peak-fitting technique was applied based on the concept of linking the character (molecular weight profile) of the recalcitrant organics in the treated water with those of the source water. This was then applied to predict DOM treatability by determining the areas of the peaks which were assigned to removable organics from the source water molecular weight profile after peak fitting, and this technique quantified the removable and non-removable organics. The prediction was compared with the actual dissolved organic carbon (DOC) removal determined from jar testing and showed good agreement, with variance between 2% and 10%. This confirmed that this prediction approach, which was originally developed for high SUVA waters, can also be applied successfully to predict DOC removal in low SUVA waters.     

Evaluation of reusing alum sludge for the coagulation of industrial wastewater containing mixed anionic surfactants

A coagulation-flocculation process is typically employed to treat the industrial wastewater generated by the consumer products industry manufacturing detergents, soaps, and others. The expenditure of chemicals including coagulants and chemicals for pH adjustment is costly for treating this wastewater. The objective of this study was to evaluate the feasibility of reusing the aluminum sulfate (alum) sludge as a coagulant or as a coagulation aid so that the fresh alum dosage can be minimized or the removal e ciency can be enhanced. The experiments were conducted in a jar-test apparatus simulating the coagulation-flocculation process for simultaneous removals of organic matters, anionic surfactants, suspended solids, and turbidity. At the optimum initial pH value of 10 and the fresh alum concentration of 400 mg/L, the total suspended solids (TSS), total chemical oxygen demand (TCOD), total anionic surfactants, and turbidity removal e ciencies were 71.5%, 76.4%, 95.4%, and 98.2%, respectively. The addition of alum sludge as a coagulant alone without any fresh alum addition could significantly remove the turbidity, TCOD, and anionic surfactants. The TSS was left in the supernatants after the settling period, but would subsequently be removed by adding the fresh alum. The TSS, TCOD, and turbidity removal e ciencies were also enhanced when both the alum sludge and the fresh alum were employed. The TCOD removal e ciency over 80% has been accomplished, which has never fulfilled by using the fresh alum alone. It is concluded that the alum sludge could be reused for the treatment of industrial wastewater generated by the consumer products industry.     

超滤及其组合工艺对污水的深度处理试验

超滤及其组合工艺 ,混凝 UF和粉末活性炭 (PAC) UF对污水深度处理的试验结果表明 ,超滤对水中浊度几乎可以完全去除 ,对细菌和大肠杆菌的去除效率大于 99% ,对水中有机物、氨氮、总铁和总锰也均有一定的去除。超滤前加混凝预处理或粉末活性炭吸附后 ,提高了水中有机物的去除率 ,同时减轻了膜污染 ,提高了膜通量和产水量。此外 ,三种工艺在等量冲洗用水的条件下 ,适当缩短过滤周期 ,增加反冲洗频率均提高了单位能耗产水量。     

混凝＋超滤联用技术净化微污染水的试验研究

采用聚合氯化铝混凝与超滤膜联用技术净化微污染水,考察该工艺净化COD、氯离子、浊度和铁离子的效果。结果表明,该工艺运行稳定,出水水质满足生活饮用水卫生标准（ GB 5749－2001）,混凝＋超滤联用技术不仅能有效地净化有机物、浊度,对铁离子和氯离子也有较好的净化效果,且出水中悬浮物、细菌和大肠菌群数未检测出。     

Influential factors of formation kinetics of flocs produced by water treatment coagulants

The growth rate and size of floc formation is of great importance in water treatment especially in coagulation process.The floc formation kinetics and the coagulation efficiency of synthetic water were investigated by using an on-line continuous optical photometric dispersion analyze and the analysis of water quality.Experimental conditions such as alum dosage,pH value for coagulation,stirring intensity and initial turbidity were extensively examined.The photometric dispersion analyze results showed that coagulation of kaolin suspensions with two coagulants(alum and polyaluminium chloride) could be taken as a two-phase process:slow and rapid growth periods.Operating conditions with higher coagulant doses,appropriate pH and average shear rate might be particularly advantageous.The rate of overall floc growth was mainly determined by a combination of hydraulic and water quality conditions such as pH and turbidity.The measurement of zeta potential indicates that polyaluminium chloride exhibited higher charge-neutralizing ability than alum and achieved lower turbidities than alum for equivalent Al dosages.Under the same operating conditions,the alum showed a higher grow rate,but with smaller floc size.     

铝盐混凝剂的混凝效果与残留铝含量和组分之间的关系研究

研究了氯化铝、硫酸铝、聚合氯化铝(poly-aluminum chloride, PAC)3种铝盐混凝剂在腐殖酸-高岭土模拟水样中的应用,以比较3种混凝剂在该水样中的混凝效果与残留铝含量和组分之间的关系.结果表明, 3种铝盐混凝剂在试验选取的投加量下对浊度和UV254的去除率最高可达90%左右,PAC能在较高的投加量下达到较好的混凝效果;较高投加量下PAC混凝沉淀出水中残留总铝含量为0.9 mg/L左右,余铝率为-3.0%左右,均明显低于传统的铝盐混凝剂;3种混凝剂混凝处理腐殖酸-高岭土模拟水样时,残留铝均大部分以溶解性总铝的形式存在,且溶解性有机铝在总溶解性铝中所占比例较大;PAC在腐殖酸-高岭土混凝沉淀出水中残留总铝的含量下降最快,且能够有效降低出水中毒性较大的溶解性铝的含量,其混凝沉淀出水中残留总溶解性铝含量为0.6 mg/L左右.     

硅藻土强化混凝去除铜绿微囊藻的影响因素研究

以原水中常见的铜绿微囊藻为研究对象,研究了联合硅藻土与聚合氯化铝(PAC)强化混凝去除铜绿微囊藻的效果.考察了PAC和硅藻土的投加量、溶液pH值、天然有机物腐植酸(HA)对藻和浊度去除的影响,并用zeta电位分析方法对混凝剂的静电中和能力进行表征.结果表明:硅藻土具有良好的助凝作用,投加其有助于改善絮体的沉降性能,提高铜绿微囊藻的混凝去除效果,PAC为6mg/L,pH值为7~8,硅藻土投加量为30mg/L时,叶绿素a(Chl-a)去除率可达96%,剩余浊度低于0.9NTU. HA存在会明显抑制铜绿微囊藻的混凝去除,当HA浓度大于1.0mg/L时, Chl-a去除率大幅度下降同时剩余浊度明显上升,硅藻土的投加可以在一定程度上缓解负面作用.     

紫外辐射对小球藻混凝效果作用途径探讨

针对藻类在常规水处理过程中难以被有效去除的现状,采用紫外辐射对藻类混凝过程进行强化处理.结果表明,随着紫外照射时间的增加,混凝后对藻细胞和浊度的去除均呈先上升后下降的趋势,并在照射50 min时达到最大值.PAC(聚合氯化铝)投加量为5 mg·L~(-1)时,照射样的除藻率和去浊率达到最大,分别比空白样高20.1%和18%左右.pH值在6~9范围内,紫外辐射强化混凝效果的变化较小.溶液pH=8、紫外照射50 min,混凝后的除藻率和去浊率分别达到了93.5%和90.6%.此时,藻细胞Zeta电位最大,同时释放出藻黏液,有利于混凝沉降.而当紫外照射超过60 min后,出现细胞膜破裂,胞内有机物渗出,使得溶液中的有机物浓度急剧上升,Zeta电位开始下降,不利于后续混凝的进行.     

无机-有机复合混凝剂处理夏季引黄水库水的对比研究

合成了具有不同Fe(Al)/聚二甲基二烯丙基氯化铵(PDMDAAC)质量比的无机-有机复合混凝剂PFC-PDMDAAC和PAC-PDMDAAC,并对夏季引黄水库水进行混凝处理.考察了复合比例、投药量、pH值和投加方式对浊度、有机物和叶绿素-a的去除效果;并通过混凝过程中形成絮体的Zeta电位的变化分析了2种混凝剂的混凝机理.结果表明,无机-有机复合混凝剂处理夏季引黄水库水的效果好于2种单独成分的复配使用;复合比例对PFC-PDMDAAC和PAC-PDMDAAC处理夏季引黄水库水的效果影响较大,Fe(Al)/PDMDAAC质量比为4:1,投药量为4mg/L时混凝效果最好;与无机混凝剂相比,复合混凝剂的最佳pH值范围较广,可在5.0~8.0的pH值范围内取得良好的混凝效果;2种混凝剂相比,PAC-PDMDAAC对浊度和叶绿素-a的去除效果较好,而PFC-PDMDAAC对有机物的去除效果更佳.     

磁性离子交换树脂对原水中有机物去除效能的研究

采用磁性离子交换树脂(MIEX)预处理原水中有机物的中试试验结果表明,MIEX技术可有效地去除原水中的有机物,对UV254,DOC和CODMn的去除率分别稳定在82%、66%和50%,MIEX预处理可以有效强化混凝沉淀对有机物、藻细胞和浊度的去除.与常规工艺相比,在混凝剂聚合氯化铝投加量降低56%时,该工艺对UV254和CODMn的去除率分别为90%和71%,对藻细胞数和浊度的去除率分别为99%和95%.对溶解性有机物分级和分子量分布的测定表明,MIEX预处理主要去除混凝沉淀无法有效去除的小分子区间的亲水性和疏水性有机物,可以有效控制消毒副产物的产生,MIEX预处理与混凝沉淀联用工艺出水的三卤甲烷生成势(THMFP)和卤乙酸生成势(HAAFP)比原水降低了88%和87%.     

三种长江原水水质与混凝效果的比较

夏季同一时期3种长江原水浊度和氨氮较低,中央沙库区原水藻类和高锰酸盐指数较高。有机物图谱分析表明,3种原水中多以苯系物、酞酸酯类等小分子有机物为主,浓度均比较低。混凝剂硫酸铝、聚硫氯化铝和聚合硫酸铝铁对于同种原水浊度的去除效果比较接近,其中聚合硫酸铝铁略好。对于陈行水库原水和青草沙库区原水,硫酸铝的最佳投量为30 mg/L,对于中央沙库区原水,在增加硫酸铝投量或改变混凝剂种类的情况下均难以达到良好的混凝效果,而预加氯工艺可有效改善其混凝效果,提高高锰酸盐指数的去除率。     

Effects of pre-ozonation on organic matter removal by coagulation with IPF-PACI

Ozone plays an important role as a disinfectant and oxidant in potable water treatment practice and is increasingly being used as a pre-oxidant before coagulation. The purpose of this study is to obtain insight into the mechanisms that are operative in pre-ozonized coagulation. Effects ofpre-ozonation on organic matter removal during coagulation with IPF-PAC1 were investigated by using PDA （photometric disperse analysis）, apparent molecular weight distribution and chemical fractionation. The dynamic formation of flocs during coagulation process was detected. Changes of aquatic organic matter （AOM） structure resulted from the influence of pre-ozonation were evaluated. Results show that dosage of O3 and characteristics of AOM are two of the major factors influencing the performance of O3 on coagulation. No significant coagulation-aid effect of O3 was observed for all experiments using either A1C13 or PAC1. On the contrary, with the application of pre-ozonation, the coagulation efficiency of A1C13 was significantly deteriorated, reflected by the retardation of floc formation, and the removal decreases of turbidity, DOC, and UV254. However, if PACl was used instead of AlCl3, the adverse effects of pre-ozonation were mitigated obviously, particularly when the O3 dosage was less than 0.69 （mg O3/mg TOC）. The difference between removals of UV254, and DOC indicated that pre-ozonation greatly changed the molecular structure of AOM, but its capability of mineralization was not remarkable. Only 5% or so DOC was removed by pre-ozonation at 0.6--0.8 mg/L alone. Fractionation results showed that the organic products of pre-ozonation exhibited lower molecular weight and more hydrophilicity, which impaired the removal of DOC in the following coagulation process.     

强化混凝消除水中全氟化合物

以十六烷基三甲基溴化铵（CTAB）有机改性膨润土作为助凝剂,采用聚合氯化铝（PAC）协同CTAB-膨润土进行强化混凝实验,对消除水中两类典型的全氟化合物全氟辛烷磺酸（PFOS）/全氟辛酸（PFOA）和浊度进行研究.考察了PAC和CTAB-膨润土投加量、pH值、原水浊度对PFOS/PFOA和浊度去除的影响.结果表明,经有机改性,实现了CTAB对膨润土的插层,增大了层间距,比表面积、阳离子交换容量、有机碳含量也得到较大提高.在PAC投加量为20mg/L、CTAB-膨润土投加量为30mg、pH6~7时,强化混凝去除效果分别达到76%、70%,PFOS/PFOA去除率随着CTAB-膨润土投加量的增大而增大.最佳pH值范围是6~7,混凝过程中Zeta电位在pH值为6.0时达到最大,pH值为7.0时接近于零.PFOS/PFOA的去除率随着原水浊度的增大而增大.     

粉炭强化循环造粒流化床去除天然有机物的研究

强化天然有机物去除是饮用水处理工艺的重要目标.循环造粒流化床作为一种新型高效固液分离技术具有处理负荷高、水质适应性强的特点,将其与粉末活性炭（PAC）联用,探究对水库水中有机物的强化去除效果.研究发现当聚合氯化铝（PACl）与PAC同时投加,且PACl、聚丙烯酰胺（PAM）及PAC投加量分别为24mg/L、1.2mg/L、30mg/L时,流化床系统对进水浊度、UV₂₅₄、COD_Mn、DOC去除率分别为96.5%、72.0%、71.7%、61.0%.对进出水中的有机物进行三维荧光分析,发现流化床系统中结团造粒作用下出水的类富里酸和类腐殖酸的FI分别比进水降低了40.1%和43.0%;加入30mg/L PAC后,出水的类富里酸和类腐殖酸的的FI分别比原水降低了54.0%和55.3%.水库水中的有机物分子量主要在 < 1kDa和10~30kDa两个区间,分别占总有机物含量的37.1%和39.1%.循环造粒流化床系统中结团造粒作用主要去除10~30kDa区间的有机物,PAC吸附作用对 < 1kDa的有机物有很好的去除.     

不同聚合铝对水中有机物的去除研究

强化混凝是去除水中消毒副产物的最佳方法之一。文章针对强化混凝技术,从去除水中有机物的角度出发,对不同聚合铝的处理效果进行了研究。结果表明,酸性条件、加大投药量有利于水中TOC及UV254的去除,且酸性条件更为有利。在pH=6.3,工业PAC投药量为1.5×10-4mo(l有效铝)时去除效果最佳,水中总有机碳(TOC)及紫外吸光度(UV25)4的去除率分别可达到46%及57%,实验室制备的聚合铝碱化度越高越有利于水中有机物的去除。     

Preferential binding between intracellular organic matters and Al13 polymer to enhance coagulation performance

Coagulation is the best available method for removing intracellular organic matter (IOM), which is released from algae cells and is an important precursor to disinfection by-products in drinking water treatment. To gain insight into the best strategy to optimize IOM removal, the coagulation performance of two Al salts, i.e., aluminum chloride (AlCl₃) and polyaluminum chloride (PACl, containing 81.2% Al₁₃), was investigated to illuminate the effect of Al species distribution on IOM removal. PACl showed better removal efficiency than AlCl₃ with regard to the removal of turbidity and dissolved organic carbon (DOC), owing to the higher charge neutralization effect and greater stability of pre-formed Al₁₃ species. High pressure size exclusion chromatography analysis indicated that the superiority of PACl in DOC removal could be ascribed to the higher binding affinity between Al₁₃ polymer and the low and medium molecular weight (MW) fractions of IOM. The results of differential log-transformed absorbance at 254 and 350?nm indicated more significant formation of complexes between AlCl₃ and IOM, which benefits the removal of tryptophan-like proteins thereafter. Additionally, PACl showed more significant superiority compared to AlCl₃ in the removal of < 5?kDa and hydrophilic fractions, which are widely viewed as the most difficult to remove by coagulation. This study provides insight into the interactions between Al species and IOM, and advances the optimization of coagulation for the removal of IOM in eutrophic water.     

水中单宁酸对强化混凝除污染的影响研究

研究了水中单宁酸在聚合氯化铝做混凝剂时对常规混凝、高锰酸钾预氧化强化混凝以及预氯化强化混凝的影响。结果表明,常规混凝下单宁酸含量的增加对混凝除浊有一定的效果,随着单宁酸投加量从0增加到5mg／L,滤后水的浊度呈现下降趋势,最低可达0．56NTU,但对于有机物的去除影响不大。高锰酸钾预氧化条件下当单宁酸投量小于2mg／L时,增大单宁酸投量有助于浊度的去除,过多则不利于混凝。预氯化下增加单宁酸投加量有助于浊度的去除,但对出水UV25。影响不大;随着单宁酸投加量从0增加到5mg/L,出水的CODMn鼻隆低白谁如,     

磁混凝工艺处理市政废水中的污染物去除特征研究

本研究对2个磁混凝站点进行了水质分析与溶解性有机物（DOM）的系统表征，考察了市政废水在磁混凝过程中的污染物去除效果与DOM去除特征，分析了强化磁混凝过程关键作用.研究发现：磁混凝可显著去除浊度、悬浮态有机物和磷，2个站点TCOD和TP去除率分别为52.53%/76.78%和64.41%/81.59%.市政废水DOM组成复杂，内源性DOM占比较高，两个站点DOM种类相似，但B站点进水有机物含量略少，且芳香类DOM占比较低.磁混凝对DOM具有显著的去除效果，主要去除高腐殖化程度、芳香性、聚合度、疏水性的大分子有机物，络氨酸类蛋白是主要的去除物质.B站点强化药剂的投加显著提升DOM和氨氮的去除效果，TOC和氨氮的去除率可达40.01%和36.08%，同时磷和TCOD的混凝效果也得到一定强化.本研究揭示了磁混凝过程污染物去除特征，促进了磁混凝过程的理解，为磁混凝在水处理中的推广应用提供了有效支撑.