镁盐和炉渣对印染废水的脱色处理

实验研究了不同pH、温度：Mg2＋投量和沉降时间下,镁盐、炉渣、镁盐＋炉渣3种处理对模拟和实际印染废水的脱色效果。结果表明,在pH为11～11．5、沉降30rain、30℃及Mg2＋投加量为500～600mg／L的最优脱色条件下,3种处理对艳红FXC模拟废水的最大脱色率分别为98．41％、98．43％和99．37％,对实际印染废水的最大脱色率分别为90．18％、89．63％和93．33％,其中,镁盐＋炉渣脱色效果最好,这可能与炉渣吸附和起到协同增强Mg（OH）2沉淀效果的作用有关。对水样的液相色谱初步检测分析表明,实际废水脱色处理前后染色基团峰高和种类发生了变化。该研究对盐田富镁卤水和炉渣等废物的资源化开发有重要参考价值。     

pH值控制MAP法脱氮进程的可行性研究

MAP沉淀法处理高NH₃-N废水,操作简便,处理效果好。本试验以NH₃-N浓度为1 000 mg/L的模拟废水为研究对象,研究结果表明,在Mg²⁺∶PO^3-₄∶NH⁺₄=1.2∶1.2∶1（摩尔比）、NaOH投加量为675 g/L的条件下NH₃-N去除率高达98%以上。试验选择出水pH作为控制反应进程的参数,并建立了出水pH与NH₃-N去除率之间的关系。通过调整NaOH投加量控制出水pH在7.5～8之间时,NH₃-N去除率最高,可达98%以上。X-衍射图谱及定量分析表明,沉淀物中MAP的纯度较高,具有一定的回收价值。     

重金属杂质对磷酸铵镁结晶法处理制药废水的影响

磷酸铵镁沉淀法处理废水时常受众多因素影响,其中重金属类杂质对该过程影响较大。实验研究了Mn²⁺、Cu²⁺杂质存在条件下,用该法去除制药废水中PO₄^3-、NH₄⁺污染物,同时,用XRD、XRF、SEM等手段研究了所得鸟粪石晶体特征。结果表明,pH为9.5时,Mn²⁺、Cu²⁺杂质存在条件下,PO₄^3-去除率分别为88%和85%,投加晶种有利于回收特定晶形鸟粪石,Cu²⁺对磷酸铵镁结晶过程的影响较Mn²⁺存在时显著。     

仿生矿化法制备壳聚糖/纳米CdS复合粒子对猩红B光催化降解研究

用仿生矿化法制备了壳聚糖/纳米CdS复合粒子,并用于可见光光催化降解猩红B染料模拟废水,系统地研究了染料初始浓度、pH值、催化剂投加量、光照情况和催化剂重复使用等因素对猩红B的光解脱色效率的影响。结果表明,当pH=3.0,催化剂投加量为0.7 g/L的条件下,对初始溶液为20 mg/L的猩红B模拟废水,60 min之内脱色率超过96%。酸性媒介比碱性媒介更有利于猩红B染料光解脱色。实验范围内Br^-、NO^-₃和Cl^-等无机阴离子,均对降解脱色有促进作用,其中NO₃^-对脱色作用促进最显著。处理前后的UV-Vis谱图分析表明猩红B在壳聚糖/纳米CdS复合粒子可见光光解处理过程中脱色是因为染料发生氧化光降作用。催化剂重复利用5次后,处理60 min对猩红B的脱色率仍可达到80.7%。     

Fenton氧化/高浓度泥浆法处理矿山废水

为了解决某大型铜矿废水COD不达标问题,采用Fenton氧化对原有高浓度泥浆（HDS）工艺进行改进。探讨了Fenton氧化矿山废水各指标的去除效果以及H₂O₂浓度对出水COD去除效果的影响,结果表明,Fenton氧化-电石乳中和絮凝沉淀工艺处理矿山废水是可行的,最优实验条件为：pH稳定在3.0～4.5,H₂O₂投加量0.5 mL/L,电石乳投加量8.5 g/L,PAM投加量1.5 mg/L;系统对废水COD的去除机理是加入的H₂O₂和矿山酸性废水中的Fe²⁺离子在低pH下形成Fenton试剂;系统对TFe、Zn²⁺、Cu2+ 的去除效果比Mn²⁺的去除效果更稳定。     

曝气+化学絮凝法预处理环氧丙烷废水简

根据环氧丙烷废水的特点,应用电化学法处理具有较高的可行性。运用电化学法处理PO废水前必须进行废水预处理,用以提高电流效率和延长极板寿命。采用曝气和化学絮凝结合的方法去除PO废水中的Ca²⁺,同时去除部分COD。对曝气、无机絮凝剂（PACl、PFS）和有机絮凝剂（PAM）对PO废水处理过程中的曝气量、曝气时间、投药量、复配和沉降时间等主要影响因子进行了实验研究,通过比较Ca²⁺、COD的去除效果、絮凝剂用量、沉降时间、处理成本等方面,在设定的实验参数下得到最佳预处理方案为：曝气量为2.5 L/min,曝气45 min,投加Na₂CO₃粉末24 kg/t 废水,充分混匀后加入PFS+PAM复配絮凝剂。本方案具有废水处理效果好（Ca²⁺的去除率为77.03%,COD的去除率为37.46%）、投药量少（（100+7.5）g/t废水）、沉降时间短（5 min）、处理成本低（0.675元/t废水）等优点。通过对比经预处理和不经预处理后电化学法对COD去除效果、电流和处理后阴极表面,验证了预处理方案的必要性与可行性。     

镁盐复合混凝剂应用于活性染料印染废水脱色的实验研究

采用镁盐与亚铁盐混合复配对活性染料印染废水进行脱色处理.考察该复合混凝剂的组分配比、pH值和投加量对脱色率的影响,并与单一组分混凝剂的脱色效果作对比,同时初步分析了复合混凝剂的脱色机理.结果表明:复合混凝剂MgSO4-FeSO4·7H2O的脱色效果明显优于单一组分,表现出显著的协同效应;对于80 mg/L的活性黑KN-B印染废水(色度为1000倍),在复合混凝剂投加量为556 mg/L、pH值在10.9左右时,脱色率可以达到99.07%;主要脱色机理表现为镁盐和亚铁盐在高pH值的环境下共沉淀生成氢氧化物絮状物吸附溶液中的染料分子一起沉降.该吸附主要为电中和吸附.吸附等温线符合Langmuir方程,复合吸附剂的饱和吸附量达1.1614 g/g.     

壳聚糖混凝处理丁腈橡胶废水的实验研究

利用壳聚糖作混凝剂处理丁腈橡胶废水。对投加量、pH、搅拌速率和沉降时间四因素进行L₉(3⁴)正交实验,确定壳聚糖混凝处理丁腈橡胶废水的最佳实验条件。结果表明,壳聚糖投加量为100 mg/L, pH为6,搅拌速率为200 r/min,沉降时间为5 min,COD去除率达96.7%,出水COD降为276 mg/L,达到国家三级排放标准。     

用H2O2/Fe3+处理高浓度含甲醛废水的研究

研究采用H₂O₂/Fe³⁺催化氧化处理高浓度含甲醛废水,探讨了双氧水和催化剂投加量、反应pH及反应温度等操作条件对处理效果的影响,并通过酸溶解回用失活催化剂。结果表明,较优的操作条件为：H₂O₂/COD（质量比）=2.2～2.6,Fe³⁺/H₂O₂（摩尔比）=0.048～0.058,反应pH 1.80～2.68,反应温度50℃,反应时间40 min;在上述操作条件下,甲醛去除率达到99%以上,COD去除率达到85%以上。失活的催化剂可通过稀酸溶解后循环使用,其效果与三价铁盐作催化剂的基本相同。采用H₂O₂/Fe³⁺处理含甲醛废水具有比采用H₂O₂/Fe³⁺较优的效果。     

氨吹脱-Fenton氧化预处理阿奇霉素废水的研究

采用氨吹脱-Fenton试剂氧化法对阿奇霉素废水进行预处理,考察了各种因素对处理效果的影响。实验结果表明：在pH值为11,吹脱时间160 min,温度30℃的条件下,氨氮浓度从2 458.7 mg/L降低到421.7 mg/L,去除率可达82.85%;Fenton氧化吹脱出水的适宜工艺条件：初始pH值为3、反应时间90 min、FeSO₄·7H₂O投加量为0.01 mol/L、H₂O₂/Fe²⁺的投加比16∶1,此时,COD去除率为72.6%;废水经预处理后,有效地改善了废水水质,提高了废水的可生化性,由初始的0.1增至0.37,为后续废水的生化处理提供了有利条件。     

Metal contamination in the lichen Alectoria sarmentosa near the copper smelter of Murdochville, Québec

Lichens were used to evaluate the metal pollution in a forest ecosystem around the smelter of Murdochville, Canada. As reached values 5.8 times higher in the smelter vicinity than in the 'background' sites. This enrichment was 2 times higher for 3 metals (Cu, Cd and Pb). The highest As, Ba, Cd, Cu, and Pb concentrations in lichens were 4, 112, 1, 23, 50 and 952mg/kg respectively. Contamination declined exponentially with increasing distance from the smelter and was related to elevation and slope exposition to the smelter flux. (206)Pb/(207)Pb and (206)Pb/(204)Pb ratios were low close to the smelter (1.16 and 18), but increased with distance to constant values (1.19 and 18.7) and showed an inverse correlation with lead concentrations. Forest contamination was detectable up to 30km from the smelter.     

Reactive barriers for Cs retention

¹³⁷Cs was dispersed globally by cold war activities and, more recently, by the Chernobyl accident. Engineered extraction of ¹³⁷Cs from soils and groundwaters is exceedingly difficult. Because the half-life of ¹³⁷Cs is only 30.2 years, remediation might be more effective (and less costly) if ¹³⁷Cs bioavailability could be demonstrably limited for even a few decades by use of a reactive barrier. Essentially permanent isolation must be demonstrated in those few settings where high nuclear level wastes contaminated the environment with ¹³⁵Cs (half-life 2.3×10⁶ years) in addition to ¹³⁷Cs. Clays are potentially a low-cost barrier to Cs movement, though their long-term effectiveness remains untested. To identify optimal clays for Cs retention, Cs desorption was measured for five common clays: Wyoming Montmorillonite (SWy-1), Georgia Kaolinites (KGa-1 and KGa-2), Fithian Illite (F-Ill), and K-Metabentonite (K-Mbt). Exchange sites were pre-saturated with 0.16 M CsCl for 14 days and readily exchangeable Cs was removed by a series of LiNO₃ and LiCl washes. Washed clays were then placed into dialysis bags and the Cs release to the deionized water outside the bags measured. Release rates from 75 to 139 days for SWy-1, K-Mbt and F-Ill were similar; 0.017% to 0.021% sorbed Cs released per day. Both kaolinites released Cs more rapidly (0.12% to 0.05% of the sorbed Cs per day). In a second set of experiments, clays were Cs-doped for 110 days and subjected to an extreme and prolonged rinsing process. All the clays exhibited some capacity for irreversible Cs uptake. However, the residual loading was greatest on K-Mbt (0.33 wt.% Cs). Thus, this clay would be the optimal material for constructing artifical reactive barriers.     

Levels of ²¹⁰Po and ²¹⁰Pb in fish and molluscs in Slovenia and the related dose assessment to the population

²¹⁰Po and ²¹⁰Pb activity concentrations in fish from the Slovenian part of Adriatic Sea, in the vicinity of a former uranium mine at ?irovski vrh and from the Slovenian market were determined. In addition, ²¹⁰Po and ²¹⁰Pb activity concentrations in squid from the Slovenian market and in mussels from the Slovenian part of the Adriatic Sea were also determined. Fish, squid and mussel consumption in Slovenia was assessed from the data available from Eurostat and Food and Agriculture Organisation (FAO) and the data used for the corresponding dose calculation. Fish species with the highest activity concentrations were grilled to assess possible loss of ²¹⁰Po during the food preparation process. Samples were freeze dried and radiochemical separation of ²¹⁰Po and ²¹⁰Pb was performed. Measurements of ²¹⁰Po were performed by alpha spectrometry and ²¹⁰Pb by a low background gas-flow proportional counter. ²¹⁰Po activity concentrations in fish, squid and mussels were from 0.039 to 35.0 Bq kg⁻¹ fresh weight and ²¹⁰Pb activity concentrations were from 0.08 to 3.03 Bq kg⁻¹ fresh weight. Grilling of fish resulted in no significant loss of ²¹⁰Po at 90 °C. The assessed combined annual effective ingestion dose due to ²¹⁰Po and ²¹⁰Pb for fish, squid and mussels consumed in Slovenia is 47.6 μSv year⁻¹.     

Role of magnetite and humic acid in radionuclide migration in the environment

Sorption of ¹³⁷Cs, ⁹⁰Sr, ¹⁵⁴Eu and ¹⁴¹Ce by magnetite has been studied at varying pH (4 to 11) in the presence and absence of humic acid. The sorption studies have also been carried out at varying ionic strength (0.01 to 0.2 M NaClO₄) and humic acid concentration (2 to 20 mg/L). Percentage sorption of ¹³⁷Cs and ⁹⁰Sr was found to be pH dependent, with the sorption increasing with increasing pH of the suspension. At any pH, the percentage sorption of ⁹⁰Sr was higher than that of ¹³⁷Cs. The results have been explained in terms of the electrostatic interaction between the positively charged metal ions and the surface charge of the magnetite which becomes increasingly negative with increasing pH. On the other hand, ¹⁵⁴Eu and ¹⁴¹Ce were found to be strongly sorbed by the magnetite at all pH values, with the sorption being independent of pH. The strong sorption of trivalent and tetravalent metal ions suggests the role of complexation reactions during sorption, apart from the electrostatic interactions. However, in the case of ¹⁴¹Ce surface precipitation of Ce(III) formed by reduction of Ce(IV) in the presence of magnetite cannot be ruled out. Presence of humic acid (2 mg/L) was found to have negligible effect on sorption of all metal ions.     

改性花生壳对Cd(Ⅱ)和Pb(Ⅱ)的吸附机理

以前期制得改性块状花生壳为对象,测定改性花生壳等电点,考察离子强度对改性花生壳吸附Cd2+和Pb2+的影响、吸附前后吸附质溶液pH变化情况及蒸馏水、NaCl、HNO3、柠檬酸和EDTA 5种解吸液对Cd2+和Pb2+的解吸效果,并通过X-射线光电子能谱仪和傅里叶变换红外光谱仪对吸附前后的改性花生壳进行表征,推测并证实了改性花生壳对Cd2+和Pb2+可能的吸附机理。结果表明,改性花生壳对Cd2+和Pb2+可能的吸附机理是:Cd2+是通过外层络合、离子交换和内层络合的联合作用被吸附的;Pb2+主要是与改性花生壳上的O、N等活性基团发生内层络合;此外,改性花生壳表面生成的二氧化锰对Cd2+和Pb2+的吸附也起到一定的作用。     

Antibiotic removal from water: Elimination of amoxicillin and ampicillin by microscale and nanoscale iron particles

Zerovalent iron powder (ZVI or Fe⁰) and nanoparticulate ZVI (nZVI or nFe⁰) are proposed as cost-effective materials for the removal of aqueous antibiotics. Results showed complete removal of Amoxicillin (AMX) and Ampicillin (AMP) upon contact with Fe⁰ and nFe⁰. Antibiotics removal was attributed to three different mechanisms: (i) a rapid rupture of the β-lactam ring (reduction), (ii) an adsorption of AMX and AMP onto iron corrosion products and (iii) sequestration of AMX and AMP in the matrix of precipitating iron hydroxides (co-precipitation with iron corrosion products). Kinetic studies demonstrated that AMP and AMX (20 mg L⁻¹) undergo first-order decay with half-lives of about 60.3 ± 3.1 and 43.5 ± 2.1 min respectively after contact with ZVI under oxic conditions. In contrast, reactions under anoxic conditions demonstrated better degradation with t_1/2 of about 11.5 ± 0.6 and 11.2 ± 0.6 min for AMP and AMX respectively. NaCl additions accelerated Fe⁰ consumption, shortening the service life of Fe⁰ treatment systems.     

胺基树脂的合成及对水中重金属离子的吸附特征

研究了使用氯甲基化聚苯乙烯交联微球为前驱体与二乙烯三胺经回流反应合成胺基树脂及其对水中Cd2+和Ni2+的吸附特征。结果表明,胺基官能团成功地嫁接到树脂表面,胺基含量为5.6 mmol/g。胺基树脂对Cd2+和Ni2+的吸附等温线表明,温度的升高有利于吸附,且吸附等温线都符合Langmuir模型。pH值对吸附的影响较大,最佳吸附pH值范围为4~6。2种金属离子在胺基树脂上的吸附都符合准二级动力学方程。     

Influence of releases of I-129 from reprocessing plants on the marine environment of the North Adriatic Sea

Compared to the pre-nuclear era, large amounts of ¹²⁹I have been released to the marine environment, especially as liquid and gaseous discharges from two European reprocessing plants located at Sellafield and La Hague. Their liquid discharges influence Northern Europe and most research was conducted in the area of the North Atlantic Ocean and the Baltic Sea. In this article data on ¹²⁹I content and ¹²⁹I/¹²⁷I ratios observed in the North Adriatic Sea, which is a rather enclosed basin of the Mediterranean Sea, are presented. To the best of our knowledge no data on ¹²⁹I in the Mediterranean Sea have previously been reported. As this area is isolated from direct liquid discharges, the main transport pathway is probably gaseous releases from reprocessing plants. Surface sea water, the marine alga Fucus virsoides, an iodine accumulator, and the Mediterranean mussel Mytilus galloprovincialis collected in 2009 and 2010, and marine sediment collected in 2005 and 2009 were analysed. The ¹²⁹I/¹²⁷I isotopic ratios observed were in the range from 0.8 to 3.0 × 10⁻⁰⁸ for seawater, from 0.06 to 0.35 × 10⁻⁰⁸ for marine sediment, from 0.05 to 0.10 × 10⁻⁰⁸ for F. virsoides and from 0.3 to 0.9 × 10⁻⁰⁸ for M. galloprovincialis.     

Impact of repeated pesticide applications on the binding and release of methyl 14C-monocrotophos and U-ring labelled 14C-carbaryl to soil matrices under field conditions

The dissipation of (O-methyl-¹⁴C) monocrotophos and U-ring labelled ¹⁴C-carbaryl was monitored for over two years in absence and presence of other insecticides using in situ soil columns. The dissipation of ¹⁴C-monocrotophos from soil treated with methomyl and carbaryl showed a faster rate of downward movement than in a control column tagged with the labelled insecticide alone. The same trend was observed in experiments with ¹⁴C-carbaryl that dissipated more readily in soil treated with non-labelled monocrotophos and methomyl. In the presence of other insecticides the percentage of bound residues was generally lower than in control experiments. The bound residues at the top of the column are released at a low rate under conditions prevailing in the field. The overall time required for dissipation of 50% of monocrotophos and carbaryl (t₅₀) as estimated from control experiment was approximately 20 and 24 weeks, respectively. The data indicate that repeated applications of pesticides might enhance the release of ¹⁴C-bound residues.     

Deltamethrin degradation and effects on soil microbial activity

Deltamethrin [(S)-cyano-3-phenoxybenzyl-cis-(1R,3R)-2,2-dimethyl) cyclo–propane carboxylate),1] labelled at gem-dimethyl groups of the cyclopropane ring was applied on two Egyptian soils at a level of 10 mg/kg soil for a laboratory incubation experiment under aerobic and anaerobic conditions. A steady decrease of soil extractable¹⁴C-residues, accompanied by a corresponding increase of non- extractable bound ¹⁴C-residues was observed over a 90-day incubation period. The percentage of evolved ¹⁴CO₂ increased with time under aerobic and anaerobic conditions in both soils. The effect of deltamethrin on soil microorganisms as well as the counter effect of microorganisms on the insecticide was also investigated. As the incubation period increased, the inhibitory effect of the insecticide on the microorganisms decreased and the evolution of carbon dioxide depended on the applied dose. The nature of soil methanol soluble residues was determined by chromatographic analysis which revealed the presence of the parent insecticide as the main product in addition to four metabolites: 3-(2′,2′-dibromovinyl)-2,2-dimethylcyclopropane carboxylic acid (II); 3-phenoxybenzaldehyde (III); 3-phenoxybenzoic acid (IV); 3-phenoxybenzyl alcohol (V).