Development and characterization of microwave composite cladding

The development of cladding through microwave radiation is recently explored and very few, initial studies were reported elsewhere. In order to explore more viability of process, (EWAC (Ni based) + 20% Cr₂₃C₆ powder) composite cladding has been developed on substrate austenitic stainless steel (SS-316). The experiments were conducted in domestic microwave oven and the clad of thickness, approximate 500 m has been developed by the exposure of microwave radiation at frequency 2.45 GHz for duration of 360 s. Typical clads cross sections of composite clads showed good metallurgical bonding with the substrate by partial dilution. The back scattered electron image of clad cross section showed the reinforced chromium carbide (Cr₂₃C₆) particles are uniformly distributed and well embedded in the Ni based matrix. The developed clad is free from visible solidification cracking and has significantly less porosity which is of the order of 0.90%. The XRD pattern of the developed clad showed the presence of FeNi₃, NiSi and Cr₂₃C₆ phases. The average Vicker's microhardness of developed clad was observed as 425 ± 140 Hv.     

Modeling increased demand of energy for air conditioners and consequent CO2 emissions to minimize health risks due to climate change in India

Developing countries situated mostly in latitudes that are projected for the highest climate change impact in the twenty-first century will also have a predictable increase in demand on energy sources. India presents us with a unique opportunity to study this phenomenon in a large developing country. This study finds that climate adaptation policies of India should consider the significance of air conditioners (A/Cs) in mitigation of human vulnerability due to unpredictable weather events such as heat waves. However, the energy demand due to air conditioning usage alone will be in the range of an extra ～750,000 GWh to ～1,350,000 GWh with a 3.7 °C increase in surface temperatures under different population scenarios and increasing incomes by the year 2100. We project that residential A/C usage by 2100 will result in CO₂ emissions of 592 Tg to 1064 Tg. This is significant given that India's total contribution to global CO₂ emissions in 2009 was measured at 1670 Tg and country's residential and commercial electricity consumption in 2007 was estimated at 145,000 GWh.     

Second generation diesel fuel from renewable sources

The study is devoted to the issue of direct transformation of triacylglycerols (TAG) to diesel fuels applying a commercially available NiMo and NiW hydrorefining catalysts. It was proved that during hydrodesulphurisation also hydrodeoxygenation occurs and TAG can be converted to the fuel biocomponent by adding 6.5 % vol. of TAG to atmospheric gas oil. In this way, after hydroprocessing at mild conditions (temperature 320–360 °C, pressure 3.5–5.5 MPa, LHSV: 1.0 h^?1 and ratio H₂:HC = 500–1000 Nm³/m³, catalyst presence), gas oil containing 5–5.5% of biocomponent was prepared, characterized with standard performance and emission parameters. Performance and emission tests documented that even 5% vol. portion of bio-components reduces the controlled and uncontrolled emissions.     

Lodging in rice can be alleviated by atmospheric CO2 enrichment

The projected increase of atmospheric CO₂ concentration [CO₂] is expected to increase yield of agricultural C₃ crops, but little is known about effects of [CO₂] on lodging that can reduce yield. This study examined the interaction between [CO₂] and nitrogen (N) fertilization on the lodging of rice (Oryza sativa L.) using free-air CO₂ enrichment (FACE) systems installed in paddy fields at Shizukuishi, Iwate, Japan (39°38′N, 140°57′E). Rice plants were grown under two levels of [CO₂] (ambient = 365 μmol mol⁻¹; elevated [CO₂] = 548 μmol mol⁻¹) and three N fertilization regimes: a single initial basal application of controlled-release urea (8 g N m⁻², CRN), split fertilization with a standard amount of ammonium sulfate (9 g N m⁻², MN), and ample N (15 g N m⁻², HN). Lodging score (six ranks at 18° intervals, with larger scores indicating greater bending), yield, and yield components were measured at maturity. The lodging score was significantly higher under HN than under CRN and MN, but lodging was alleviated by elevated [CO₂] under HN. This alleviation was associated with the shortened and thickened lower internodes, but was not associated with a change in the plant's mass moment around the culm base. A positively significant correlation between lodging score and ripening percentage indicated that ripening percentage decreased by 4.5% per one-unit increase in lodging score. These findings will be useful to develop functional algorithm that can be incorporated into mechanistic crop models to predict rice production more accurately in a changing climate and with different cultural practices.     

Micro-flood (MF) technology for sustainable manufacturing operations that are coolant less and occupationally friendly

This paper presents a new technology for minimizing the use of metalworking fluids (MWFs) during the machining process that is atomization-less and occupational friendly. Micro-flood (MF) technology utilizes direct contact between the cutting tool and the MWF without the interaction of a gas medium. Experiments were conducted in high volume mass production environment turning HSLA (high strength low alloy) SAE 070Y steel. Machining performance and total air mass particulates were investigated in dry machining, Near dry machining (NDM) via atomized spray mist and MF technology. Open-atmosphere air monitoring indicated that total mass particulates behaved in an almost linear fashion with respect to gas atomization pressure, whereas the MWF flow rate demonstrated logarithmic trends in NDM applications using an atomized spray. Nozzle orientations directed upward into the air also produced higher mg/m³ concentrations (such as flank) than chip and rake face orientations that were directed down. Greater separation existed at higher gas atomization pressures, MWF flow rates and by changing the MWF type. At extreme limits, nozzle orientation affected mg/m³ concentration as much as 4–5 mg/m³ for water-miscible MWFs and 15–22 mg/m³ for non-water-miscible MWFs. Tool-life performance varied greatly among MWF type and flow rate, and in all cases MF technology performed better than NDM using an atomized spray mist. Direct and consistent MWF penetration to cutting zone using MF technology lowered tool-wear on the average of 12–75% compared to NDM at the same MWF flow rate. Compared to dry machining, NDM improved tool-wear on the average by 20–243%. In one case, tool-wear performance was improved by 616% at 0.15 mm using MF technology compared to dry machining at a nominal 0.925 mm tool-wear. Overall, a large mass reduction of particulates can be achieved employing MF technology that would have been unrealistic for an open-atmosphere machining environment employing an atomized spray mist. On the average, MF technology can maintain a total air mass particulate of less than 0.4 mg/m³ in the occupational work zone using MWF flow rates up to 1260 ml/h, regardless of the MWF classification. Atomized spray mist applications are capable meeting the 5 mg/m³ OSHA limit if MWF flow rates are less than 160 ml/h, air pressures are less than 0.137 MPa (20 psi) using water-miscible MWFs and air pressures are less than 0.0344 MPa (5 psi) using non-water-miscible MWFs.     

Effects of irrigation,fertilization and crop straw management on nitrous oxide and nitric oxide emissions from a wheat–maize rotation field in northern China

One-year winter wheat–summer maize rotation is the most popular double cropping system in north-central China, and this highly productive system is an important source of nitrous oxide (N₂O) and nitric oxide (NO) emissions due to the high fertilizer N and irrigation water inputs. To sustain the high crop production and mitigate the detrimental impacts of N₂O and NO emissions, improved management practices are extensively applied. The aim of this study is therefore to evaluate the effects of an improved management practice of irrigation, fertilization and crop straw on grain yield and N₂O and NO emissions for a wheat–maize rotation field in northern China. Using automated and manual chamber measuring systems, we monitored N₂O and NO fluxes for the conventional (CT, 2007–2008), improved (IT, 2007–2008), straw-amended (WS, 2008–2009), straw-not-amended (NS, 2008–2009), and no N-fertilizer treatments (WS–NN, 2008–2009), respectively, for one rotation-year. The grain yields were determined for CT and IT for three rotation-years (2005–2008) and for WS, NS and WS–NN for one rotation-year (2008–2009). The improved management of irrigation and fertilization reduced the annual N fertilization rate and irrigation amount by 17% and 30%, respectively; increased the maize yield by 7–14%; and significantly decreased the N₂O and NO emissions by 7% (p < 0.05) and 29% (p < 0.01), respectively. The incorporation of wheat straw increased the cumulative N₂O and NO emissions in the following maize season by 58% (p < 0.01) and 13%, respectively, whereas the effects of maize straw application were not remarkable. The N₂O and NO emission factors of applied N were 2.32 ± 2.32% and 0.42 ± 1.69% for wheat straw and 0.67 ± 0.23% and 0.54 ± 0.15% for chemical N-fertilizers, respectively. Compared to conventional management practices using high application rates of irrigation water and chemical N-fertilizer as well as the field burning of crop straw, the improved management strategy presented here has obvious environmentally positive effects on grain yield and mitigation of N₂O and NO emissions.     

Nitrous oxide emissions from organic and conventional crop rotations in five European countries

Nitrous oxide (N₂O) emissions from agriculture are currently estimated from N inputs using emission factors, and little is known about the importance of regional or management-related differences. This paper summarizes the results of a study in which N₂O emission rates were recorded on 15–26 occasions during a 12-month period in organic and conventional dairy crop rotations in five European countries (Austria, Denmark, Finland, Italy, UK). A common methodology based on static chambers was used for N₂O flux measurements, and N₂O data were compiled together with information about N inputs (from fertilizers, N₂ fixation, atmospheric deposition and excretal returns), crop rotations and soil properties. Organic rotations received only manure as N fertilizer, while manure accounted for 0–100% of fertilizer N in conventional rotations. A linear regression model was used to examine effects of location, system and crop category on N₂O emissions, while a second model examined effects of soil properties. Nitrous oxide emissions were higher from conventional than from organic crop rotations except in Austria and, according to the statistical analysis, the differences between locations and crop categories were significant. Ammonium was significantly related to N₂O emissions, although this effect was dominated by observations from a grazing system. Despite the limited number of samplings, annual emissions were estimated by interpolation. Across the two systems and five locations there was a significant relationship between total N inputs and N₂O emissions at the crop rotation level which indicated that annually 1.6 ± 0.2% (mean ± standard error) of total N inputs were lost as N₂O, while there was a background emission of 1.4 ± 0.3 kg N₂O-N ha⁻¹ year⁻¹. Although this measurement program emphasized system effects at the expense of high temporal resolution, the results indicate that N input is a significant determinant for N₂O emissions from agricultural soils.     

Dairy farm CH4 and N2O emissions,from one square metre to the full farm scale

The greenhouse gas emissions from agricultural systems contribute significantly to the national budgets for most countries in Europe. Measurement techniques that can identify and quantify emissions are essential in order to improve the selection process of emission reduction options and to enable quantification of the effect of such options. Fast box emission measurements and mobile plume measurements were used to evaluate greenhouse gas emissions from farm sites. The box measurement technique was used to evaluate emissions from farmyard manure and several other potential source areas within the farm. Significant (up to 250 g CH₄ m⁻² day⁻¹and 0.4 g N₂O m⁻² day⁻¹) emissions from ditches close to stables on the farm site were found.Plume emission measurements from individual manure storages were performed at three sites. For a manure storage with 1200 m³ dairy slurry in Wageningen emission factors of 11 ± 5 g CH₄ m⁻³ manure day⁻¹ and 14 ± 8 mg N₂O m⁻³ manure day⁻¹ were obtained in February 2002.Mobile plume measurements were carried out during 4 days at distances between 30 and 300 m downwind of 20 different farms. Total farm emissions levels ranged from 14 to 95 kg CH₄ day⁻¹ for these sites. Expressed as emission per animal the levels were 0.7 ± 0.4 kg CH₄ animal⁻¹ day⁻¹ for conventional farms. For three farms that used straw bedding for the animals1.4 ± 0.2 kg CH₄ animal⁻¹ day⁻¹ was obtained. These factors include both respired methane and emission from manure in the stable and the outside storages.For a subset of these farms the CH₄ emission was compared with monthly averaged model emission calculations using FarmGHG. This model calculates imports, exports and flows of all products through the internal chains on the farm using daily time steps. The fit of modelled versus measured data has a slope of 0.97 but r² = 0.27. Measurements and model emission estimates agree well on average, for large farms within 30%. For small farms the differences can be up to a factor of 3. CH₄ emissions during winter seem to be underestimated.     

Metal-cored arc welding process for joining of modified 9Cr-1Mo (P91) steel

In the present work, metal-cored arc welding process was used for joining of modified 9Cr-1Mo (P91) steel. Metal-cored arc welding process is characterized by high productivity, slag-free process, defect-free weldments that can be produced with ease, and good weldability. Toughness is essential in welds of P91 steel during hydro-testing of vessels. There is a minimum required toughness of 47 J for welds that has to be met as per the EN1557:1997 specification. In the present study, welds were completed using two kinds of shielding gases, each composition being 80% Argon + 20% CO₂, and pure argon respectively. Microstructural characterization and toughness evaluation of welds were done in the as – weld, PWHT at 760 °C – 2 h and PWHT at 760 °C – 5 h conditions. The pure argon shielded welds (‘A2’ and ‘B2’) have higher toughness than 80% argon + 20% CO₂ shielded welds (‘A1’ and ‘B1’). Pure argon shielded welds show less microinclusion content with low volume fraction of δ-ferrite (<2%) phase. Themo-calc windows (TCW) was used for the prediction of equilibrium critical transformation points for the composition of the welds studied. With increase in post-weld heat treatment (PWHT) duration from 2 h to 5 h, there was increase in toughness of welds above 47 J. Using metal-cored arc welding process, it was possible to achieve the required toughness of more than 47 J after PWHT at 760 °C – 2 h in P91 steel welds.     

The effect of pitting corrosion on split sleeve cold hole expanded,bare 7075-T651 aluminium alloy

As part of an aircraft fleet fatigue life improvement program, investigation has been carried out into the effect pitting corrosion has on bare 7075-T651 which had undergone split sleeve cold hole expansion. Constant amplitude sinusoidal loading was applied to fatigue test coupons which had pitting corrosion induced upon them by a modified cyclic immersion process using a 3.5% NaCl solution. A pit depth of 39–58 μm was found to significantly reduce the increased fatigue life gains achieved by carrying out cold hole expansion. At 137.9 MPa fatigue life was reduced from achieving run out of ten million cycles to an average 371 × 10³ cycles, while at 165.5 MPa average fatigue life was reduced from 810 × 10³ to 65 × 10³ cycles. The fracture surfaces were analysed under a scanning electron microscope where each displayed an individual crack initiation site located on the material surface within the zone of residual circumferential stress.     

Reduction of hexavalent chromium by polypyrrole-modified steel mesh electrode

Adherent polypyrrole (ppy) films were electropolymerized from a para-toluenesulfonic sodium (PTS) solution on stainless steel mesh (SSM). Reduced ppy-modified SSM electrode can transfer Cr(VI) to Cr(III) effectively. Lower pH (<2) or higher temperature (>35 °C) is beneficial for the removal of Cr(VI). Electro-reduction achieved 90% removal efficiency after 21 min by cyclic voltammetry. The removal efficiency is 96–56% for one–six contact cycles between ppy and Cr(VI). SEM shows that ppy films on SSM have regular morphology with small nucleus of less than 1 μm in diameter.     

Simultaneous recovery of chromium and destruction of organics from LCD manufacturing process wastewater by supercritical water oxidation

The effectiveness of supercritical water oxidation (SCWO) process for the simultaneous recovery of chromium and destruction of organics from liquid crystal display (LCD) manufacturing process wastewater was investigated. The experiments were performed in an isothermal continuous-flow tubular reactor and H₂O₂ was used as an oxidant. The reaction temperatures ranged from 400 to 605 °C and the residence times ranged from 15 to 31 s at a fixed pressure of 25 MPa. The effect of temperature, oxidant concentration and residence time on chromium recovery and chemical oxygen demand (COD) conversion was investigated. The results of this study demonstrated that the SCWO process recovered chromium and decreased chemical oxygen demand up to 99.3% and 99.9%, respectively. The analyses showed that chromium are recovered as chromium oxide (α-HCrO₂ and Cr₂O₃). The SCWO process is an effective technique for simultaneously recovering chromium and for the destruction of hazardous organics in the LCD manufacturing process wastewater. Our study showed that there are two consequent reactions, chromium recovery reaction (hydrolysis) followed by the organic decomposition reaction (oxidation). The recovery of chromium can be achieved without major organic decomposition.     

Emissions of N2O and NH3, and nitrogen leaching from direct seeded rice under different tillage practices in central China

Tillage practices affect the fate of fertilizer nitrogen (N) through influencing transformations of N, but few studies have examined N₂O and NH₃ emissions, and N leaching from different rice tillage systems. Thus the objective of this study was to assess N₂O emission, NH₃ volatilization and N leaching from direct seeded rice in conventional tillage (CT) and no-tillage (NT) production systems in the subtropical region of China during the 2008 and 2009 rice growing seasons. Treatments were established following a split-plot design of a randomized complete block with tillage practices as the main plot and N fertilizer level as the sub-plot treatment, and there were four treatments: NT + no fertilizer (NT0), CT + no fertilizer (CT0), NT + compound fertilizer (NTC) and CT + compound fertilizer (CTC), respectively. Results showed that N fertilization significantly increased (p < 0.01) N₂O emissions, NH₃ volatilization and N leaching from rice fields in both years. In general, there was no significant difference in N₂O emissions and NH₃ volatilization between NT0 and CT0 in both years, while NTC had significantly higher (p < 0.05) N₂O emissions and NH₃ volatilization compared to CTC. Over the two rice growing seasons, NTC showed 32% and 47% higher N₂O emissions, and 29% and 52% higher NH₃ losses than CTC. Higher (p < 0.05) N₂O emissions from NTC than CTC were presumably due to higher soil organic C and greater denitrification. Total N and NO₃^? concentrations were higher (p < 0.05) in CTC than NTC, but larger volumes of percolation water in NTC than CTC resulted in no significant difference in leakage of total N and NO₃^?. Hence, application of N fertilizer in combination with NT appeared to be ineffective in reducing N losses from N fertilizer in paddy fields.     

Ammonia and nitrous oxide emissions following land application of high and low nitrogen pig manures to winter wheat at three growth stages

Nitrous oxide (N₂O) and ammonia (NH₃) emissions from surface applied high (HN) and low (LN) nitrogen pig manures were measured under field conditions. Manures were band-spread to a winter wheat crop at three growth stages—mid-tillering, stem elongation and flag leaf emergence. The N₂O flux rates were measured using the static chamber technique while NH₃ volatilisation was assessed using a micrometeorological mass balance technique with passive flux samplers. The N₂O emissions were episodic in nature with flux rates observed ranging from 2.8 to 31.5 g N₂O–N ha^?1 day^?1 (P < 0.001). Higher N₂O emissions generally occurred after rainfall events. Highest N₂O losses were observed from the HN treatment with LN manure use decreasing emissions by 18% (P < 0.03). The NH₃ volatilisation rates were highest within 1 h of manure application with 95% of emissions occurring within 24 h (P < 0.001). Cumulative N loss was highest at mid-tillering as low crop canopy cover and increased wind-speeds enhanced NH₃ loss (P < 0.001). Highest emissions were measured from the HN manure (P < 0.03). Total ammoniacal N loss ranged from 6 to 11%. Crop N uptake and grain yield were unaffected by application timing or manure type. Therefore, the use of LN manures decreased gaseous emissions of N₂O and NH₃ without any adverse effects on crop performance.     

Comparing carbon fluxes between different stages of secondary succession of a karst grassland

Abandonment of marginal agricultural areas with subsequent secondary succession is a widespread type of land use change in Mediterranean and mountain areas of Europe, leading to important environmental consequences such as change in the water balance, carbon cycling, and regional climate. Paired eddy flux measurement design with grassland site and tree/shrub encroached site has been set-up in the Slovenian Karst (submediterranean climate region) to investigate the effects of secondary succession on ecosystem carbon cycling. The invasion of woody plant species was found to significantly change carbon balance shifting annual NEE from source to an evident sink. According to one year of data succession site stored ?126 ± 14 g C m^?2 y^?1 while grassland site emitted 353 ± 72 g C m^?2 y^?1. In addition, the seasonal course of CO₂ exchange differed between both succession stages, which can be related to differences in phenology, i.e. activity of prevailing plant species, and modified environmental conditions within forest fragments of the invaded site. Negligible effect of instrument heating was observed which proves the Burba correction in our ecosystems unnecessary. Unexpectedly high CO₂ emissions and large disagreement with soil respiration especially on the grassland site in late autumn indicate additional sources of carbon which cannot be biologically processes, such as degassing of soil pores and caves after rain events.     

On the relationship between PM2.5 concentrations and regional-scale primary PM emissions for the United Kingdom: an issue of subsidiarity

A site-specific particulate matter PM source apportionment model has been used to estimate the contributions from local primary PM emissions, regional primary PM emissions and the regional background to PM_2.5 concentrations at 102 monitoring site locations and to the centres of 1 km × 1 km grid squares across the United Kingdom. The local primary PM contributions have then been compared with Europe-wide urban PM_2.5 increments estimated at 50 km × 50 km in European-scale integrated assessment models. It is concluded that Europe-wide PM increments used in policy analyses grossly underestimate urban PM concentrations obtained from the site-specific PM source apportionment model for the United Kingdom. Europe-wide urban PM_2.5 increments estimated at 5 km × 5 km scale are significantly improved, particularly for London, but underestimate those for smaller towns and cities by factors of 2–3. These underestimations have important air quality policy ramifications. Although environmental policies may well be best formulated at the European scale, the underpinning air quality modelling may be best carried out at the local scale.     

Comparing intensive,extensified and organic grassland farming in southern Germany by process life cycle assessment

To reduce the environmental burden of agriculture, suitable methods to comprehend and assess the impact on natural resources are needed. One of the methods considered is the life cycle assessment (LCA) method, which was used to assess the environmental impacts of 18 grassland farms in three different farming intensities — intensive, extensified, and organic — in the Allgäu region in southern Germany. Extensified and organic compared with intensive farms could reduce negative effects in the abiotic impact categories of energy use, global warming potential (GWP) and ground water mainly by renouncing mineral nitrogen fertilizer. Energy consumption of intensive farms was 19.1 GJ ha⁻¹ and 2.7 GJ t⁻¹ milk, of extensified and organic farms 8.7 and 5.9 GJ ha⁻¹ along with 1.3 and 1.2 GJ t⁻¹ milk, respectively. Global warming potential was 9.4, 7.0 and 6.3 CO₂-equivalents ha⁻¹ and 1.3, 1.0 and 1.3 CO₂-equivalents t⁻¹ milk for the intensive, extensified and organic farms, respectively. Acidification calculated in SO₂-equivalents was high, but the extensified (119 kg SO₂ ha⁻¹) and the organic farms (107 kg SO₂ ha⁻¹) emit a lower amount compared with the intensive farms (136 kg SO₂ ha⁻¹). Eutrophication potential computed in PO₄-equivalents was higher for intensive (54.2 kg PO₄ ha⁻¹) compared with extensified (31.2 kg PO₄ ha⁻¹) and organic farms (13.5 kg PO₄ ha⁻¹). Farmgate balances for N (80.1, 31.4 and 31.1 kg ha⁻¹) and P (5.3, 4.5 and −2.3 kg ha⁻¹) for intensive, extensified and organic farms, respectively, indicate the different impacts on ground and surface water quality. Analysing the impact categories biodiversity, landscape image and animal husbandry, organic farms had clear advantages in the indicators number of grassland species, grazing cattle, layout of farmstead and herd management, but indices in these categories showed a wide range and are partly independent of the farming system.     

Using supercritical carbon dioxide as solvent to replace water in polyethylene terephthalate (PET) fabric dyeing procedures

Dyeing fabrics in supercritical carbon dioxide (SCD) instead of water can save energy, reduce water use and prevent pollution. The special pilot plant was designed to test dyeing procedures in supercritical carbon dioxide and the analyses of the results indicate major benefits as compared to water based procedures. The dyeing of polyethylene terephthalate (PET) fabric in supercritical carbon dioxide using special pilot plant was investigated. Disperse dye, C.I. (color index) Disperse Blue 79, was used in this study. After dyeing, rinsing in supercritical carbon dioxide, which removes the excess dyes, was also discussed. At the same dyeing conditions, K/S (color yield) of dyed fabric significantly increased with increasing the dye concentration from 1% o.w.f. (on weight of fabric) to 5% o.w.f. Dyeing temperature and pressure had a strong influence on the color yield. When the temperature rose above 110 °C, the increase in color yield was obvious. At 20 MPa, 120–130 °C, dyeing reached equilibrium after 60 min. The excess dye of the dyed PET fabric was small. The suitable condition in supercritical carbon dioxide for removal of excess dye from the dyed fabric was 70 °C, 20 MPa. The PET fabric dyed in supercritical carbon dioxide had good fastness and physical properties.     

Disaggregated greenhouse gas emission inventories from agriculture via a coupled economic-ecosystem model

Estimates of regional greenhouse gas emissions from agricultural systems are needed to evaluate possible mitigation strategies with respect to environmental effectiveness and economic feasibility. Therefore, in this study, we used the GIS-coupled economic-ecosystem model EFEM–DNDC to assess disaggregated regional greenhouse gas (GHG) emissions from typical livestock and crop production systems in the federal state of Baden-Württemberg, Southwest Germany. EFEM is an economic farm production model based on linear programming of typical agricultural production systems and simulates all relevant farm management processes and GHG emissions. DNDC is a process-oriented ecosystem model that describes the complete biogeochemical C and N cycle of agricultural soils, including all trace gases.Direct soil emissions were mainly related to N₂O, whereas CH₄ uptake had marginal influence (net soil C uptake or release was not considered). The simulated N₂O emissions appeared to be highly correlated to N fertilizer application (R² = 0.79). The emission factor for Baden-Württemberg was 0.97% of the applied N after excluding background emissions.Analysis of the production systems showed that total GHG emissions from crop based production systems were considerably lower (2.6–3.4 Mg CO₂ eq ha⁻¹) than from livestock based systems (5.2–5.3 Mg CO₂ eq ha⁻¹). Average production system GHG emissions for Baden-Württemberg were 4.5 Mg CO₂ eq ha⁻¹. Of the total 38% were derived from N₂O (direct and indirect soil emissions, and manure storage), 40% were from CH₄ (enteric fermentation and manure storage), and 22% were from CO₂ (mainly fertilizer production, gasoline, heating, and additional feed). The stocking rate was highly correlated (R² = 0.85) to the total production system GHG emissions and appears to be a useful indicator of regional emission levels.     

Water jet guided laser as an alternative to EDM for micro-drilling of fuel injector nozzles: A comparison of machined surfaces

To characterize the inner surface of the fuel injector nozzle holes drilled by EDM and water jet guided laser drilling (Laser Micro-Jet) a specifically conceived scanning probe microscopy technique with true non-contact operating mode was used. A difference in morphology of the drilled surfaces is evident from the acquired surface topography along the hole axis for the two compared drilling techniques. Results showed that the surface texture can be characterized by (i) maximum peak-to-valley distance and (ii) periodicity. Acquired maps confirm that electro-eroded surfaces are an envelope of craters randomly distributed with total excursion up to 1.7 μm with a crater size of 15 μm. While, the efficient melt expulsion and immediate cooling of water jet guided laser generates a peak to valley distance of 800 nm with a periodicity of 18 μm. Average R_q derived from the measured cylindrical surfaces was 450 nm and 150 nm for EDM and Laser Micro-Jet, respectively. Water jet guided laser drilling has proved to be a reliable alternative to EDM from the point of view of repeatability of the results and surface quality to facilitate the atomization of the fuel jet.