垃圾填埋场生物覆盖材料筛选及甲烷减排

通过模拟柱实验研究了消化污泥、矿化垃圾和黏土作为垃圾填埋场生物覆盖材料的甲烷氧化能力。3种材料的甲烷日氧化率平均值、总氧化率和氧化速率V(CH4)分别是:消化污泥10.27%、75.82%、1.76 mmol/(kg·d);矿化垃圾11.05%、75.61%、2.04 mmol/(kg·d);黏土9.05%、68.15%、1.33 mmol/(kg·d),消化污泥和矿化垃圾对甲烷的氧化能力均大于黏土。进一步探讨了消化污泥中添加粉煤灰、建筑垃圾和黏土进行改性后对甲烷的氧化能力,考察了改性污泥的渗透系数和抗压强度。结果表明:粉煤灰对消化污泥的改性效果最好,其日氧化率平均值、总氧化率和V(CH4)分别达到17.27%、92.37%和2.35 mmol/(kg·d),粉煤灰与消化污泥以1∶1～1.5∶1混配后可满足填埋场对覆盖材料渗透系数和抗压强度的要求。     

矿化污泥生物反应器处理生活垃圾填埋场老龄渗滤液

经长时间稳定化形成的矿化污泥中,含有种类丰富和数量繁多的降解性微生物,具有处理渗滤液的潜力。建立3个矿化污泥生物反应器,即C1(粉煤灰0%),C2(粉煤灰9.1%),C3(粉煤灰16.7%),以处理垃圾填埋场老龄渗滤液。在单级矿化污泥反应器中,当进水COD和NH3-N分别约为1350和900 mg/L时,水力负荷为17.7～70.8 L/(m3.d),COD去除率可超过65%,氨氮的去除率可超过94%。粉煤灰的加入一定程度上降低了COD去除率,但有助于氨氮的去除。在二级矿化污泥生物反应器中(即C3～C1串联),水力负荷为35.4 L/(m3.d)的工况下,当COD、TOC、IC和NH3-N分别为1 500～2 500,500～900,1 200～1 600和1 200～1 450 mg/L时,出水可达到COD<300 mg/L,TOC<180 mg/L,IC<100 mg/L,NH3-N<5 mg/L。但是,矿化污泥生物反应器对渗滤液总氮的去除率较低,仅为20%左右。     

典型危险废物的工程力学特性

掌握填埋废物的工程力学特性是确保危险废物填埋堆体稳定性的重要前提条件,因此,针对6种典型危险废物的工程力学特性开展了调查研究.研究结果表明,污泥类危险废物的含水率和有机质含量远高于非污泥类危险废物,而前者的比重则显著低于后者.污泥类危险废物的渗透系数相对较小,比污染土壤和飞灰炉渣混合物的渗透系数小1个数量级,比滤池填料的渗透系数小2个数量级.不同危险废物的无侧限抗压强度排序为:飞灰炉渣混合物(314.3 kPa)和滤池填料(278.9 kPa)＞污染土壤(124.9 kPa)＞杭州氧气厂污泥(68.6 kPa)、锌铬污泥(71.4 kPa)、油泥(58.4 kPa).不同危险废物的粘聚力排序为:飞灰炉渣混合物(40.8 kPa)、滤池填料(31.1 kPa)＞污染土壤(20.9 kPa)＞杭州氧气厂污泥(1.94kPa)、锌铬污泥(3.10 kPa)、油泥(1.81 kPa).此外,不同危险废物的内摩擦角差异相对较小,其变化范围在18.8°～35.0°之间.综合分析可知,飞灰炉渣混合物和滤池填料的工程力学特性较好,而污泥类危险废物的工程力学特性则较差.     

添加剂对餐厨垃圾厌氧发酵产氢的影响

以表面活性剂与偏硅酸钠的混合物作为添加剂,考察了添加剂的投加量对餐厨垃圾厌氧产氢效果的影响.实验结果表明,添加剂能抑制产甲烷菌的生长,且接种污泥无需预处理即可提高产氢量.另外,随着添加剂投加量的增大.体系中氢气的浓度增大,在5 g(干重)餐厨垃圾投加添加剂为1.75 g时,产氢量为114.5 mL(以每克挥发性固体(VS)计).但从经济和实用两方面考虑,选择最佳添加剂量为1.00 g.     

CTMAB-改性矿化垃圾吸附苯酚性能的研究

文中研究采用表面活性剂十六烷基三甲基溴化铵(CTMAB)对矿化垃圾进行改性,利用CTMAB-改性矿化垃圾对苯酚溶液进行吸附,在单因素法条件下得到其对苯酚最佳吸附条件为:(1)改性矿化垃圾吸附平衡时间为15 min;(2)改性矿化垃圾吸附性能均随着pH值升高而降低;(3)40℃以下温度对改性矿化垃圾吸附效果影响不大。本研究还进行了等温吸附方程拟合,并对矿化垃圾和CTMAB-改性矿化垃圾对苯酚的吸附条件和吸附性能进行了比较,结果表明,矿化垃圾和改性矿化垃圾对苯酚的吸附采用Langmuir方程和Freundlich方程拟合度较好,而Temkin方程拟合度较差,改性矿化垃圾吸附性能优于未改性矿化垃圾。     

城市生活污泥和矿化垃圾中氮磷淋失的模拟研究

通过模拟土柱实验,分析了城市生活污泥和矿化垃圾中氮磷的迁移对地下水的影响以及矿化垃圾对氮磷的去除特性.测定项目包括总磷、总氮、硝态氮、pH和电导率(EC).结果表明:施用污泥和矿化垃圾后淋滤液的pH呈下降趋势;EC和总氮都有显著增加;硝态氮增加特别明显,容易造成地下水污染;总磷变化不大,污染地下水的可能性较小.矿化垃圾对氮的去除作用不明显,反而增加了淋滤液中的氮素含量,但对磷的去除效果明显.因此,在利用矿化垃圾取代土壤时,应注意矿化垃圾中氮特别是硝态氮的污染.     

不同来源污泥接种餐厨垃圾厌氧发酵产氢效果研究

在相同接种配比(接种污泥占餐厨垃圾的质量分数为30%)条件下,研究了4种不同来源污泥(压滤污泥、厌氧污泥、曝气污泥和河底淤泥)添加或不添加缓冲剂时对餐厨垃圾厌氧发酵产氢效果的影响.结果发现,在不添加缓冲剂时.4种污泥接种餐厨垃圾厌氧发酵平均产氢量依次为厌氧污泥>河底淤泥>压滤污泥>曝气污泥,接种厌氧污泥的餐厨垃圾平均产氢量最高,达10.11mL(以每克挥发性固体(VS)计,下同);而添加缓冲剂时.4种污泥接种餐厨垃圾厌氧发酵平均产氢量依次为厌氧污泥>曝气污泥>压滤污泥>河底淤泥,接种厌氧污泥的餐厨垃圾平均产氢量也最高,为33.72 mL,且体系pH得以缓冲.     

造纸污泥固化/稳定化处理技术研究

为了能更好地无害化处理造纸污泥,对造纸污泥的固化/稳定化处理技术进行了研究。以水泥、粉煤灰和煤渣作为固化剂对造纸污泥进行固化/稳定化处理。通过抗压强度评价污泥固化块的力学性质;并对固化块浸出液的COD浓度与重金属质量浓度进行了检测。当水泥、粉煤灰和煤渣的掺量分别为0.12、0.02和0.10 kg/kg,养护时间为6 d时,固化块抗压强度达到360 kPa。结果表明,水泥和煤渣对提高造纸污泥固化块的抗压强度具有促进作用,而它们与粉煤灰对造纸污泥中的有机质和重金属均具有一定的固化作用。在以上条件下,固化块浸出液中COD浓度约为115.7 mg/L,重金属浓度符合国家标准。经养护后的固化块含水率均保持在35%~40%,符合填埋场的进场标准。     

矿化垃圾对污泥厌氧消化产甲烷的影响

在序批式厌氧反应器中探究了矿化垃圾对污泥厌氧消化产甲烷的影响。实验结果表明,矿化垃圾能够提高甲烷的产量并且提高甲烷的体积分数。当矿化垃圾投加量由0增加到5 g·L~(-1)时,甲烷的产量也由168.9 m L·(g VSS)-1(挥发性悬浮固体)增加到218.6 m L·(g VSS)-1,体积分数由60%增加至70%。然而继续提高矿化垃圾的投加量至7 g·L~(-1)对污泥厌氧消化造成一定的抑制作用。矿化垃圾的存在能够提高污泥中溶解性化学需氧量(SCOD)的溶出,挥发性脂肪酸的积累进而为产甲烷菌提供了充足的消化底物,从而提高了甲烷的产量。     

塔式矿化垃圾生物反应床处理垃圾填埋场渗滤液的效能研究

通过正交试验研究了固液比、进水COD和运行周期对塔式矿化垃圾生物反应床处理垃圾渗滤液的性能影响.小试试验结果表明,在温度为10～37 ℃条件下,固液比是影响污染物去除性能的关键因素.现场中试研究表明,在水力负荷为0.267～0.444 m3/d(以每立方米矿化垃圾计)条件下,出水COD和出水氨氮基本满足国家二级排放标准.塔式矿化垃圾生物反应床是一种高效低耗的垃圾渗滤液处理工艺.     

Optimising the preparation of activated carbon from digested sewage sludge and coconut husk.

Preparation of activated carbon from sewage sludge is a promising way to dispose of sewage sludge as well as to produce a low-cost adsorbent for pollutant removal. This research work aimed to optimise the condition for activated carbon preparation from anaerobically digested sewage sludge with the additive coconut husk. The sewage sludge sample was mixed with the additive coconut husk. The preparation condition variables investigated involved the concentration of the ZnCl2 solutions, heating temperature, dwell time and heating rate in pyrolysis and the mixing ratio of coconut husk to sewage sludge. Surface area, pore size distribution, aqueous phenol adsorption capacity and the production yield of the final products were determined and compared. Experimental results revealed that low concentrations of ZnCl2 solution tended to improve the microporosity of the final product. Heating temperature had a considerable impact on the surface area, pore size distribution and phenol adsorption capacity of the final products, whereas dwell time and heating rate performed comparatively insignificantly. The effect of increasing the mixing ratio of coconut husk to sewage sludge was principally to increase the microporosity of the final products. The activated carbon with the highest BET surface area was produced with the activation of 5 M ZnCl2 solution and, thereafter, pyrolysis at a heating temperature of 500 degrees C for 2 h with a heating rate of 10 degrees C/min. The mixing ratio of 1:4 in terms of coconut husk to sewage sludge based on their dried weights was found to be most cost effective.     

Effects of sewage sludge amendment on heavy metal accumulation and consequent responses of Beta vulgaris plants

Use of sewage sludge, a biological residue produced from sewage treatment processes in agriculture is an alternative disposal technique of waste. To study the usefulness of sewage sludge amendment for palak (Beta vulgaris var. Allgreen H-1), a leafy vegetable and consequent heavy metal contamination, a pot experiment was conducted by mixing sewage sludge at 20% and 40% (w/w) amendment ratios to the agricultural soil. Soil pH decreased whereas electrical conductance, organic carbon, total N, available P and exchangeable Na, K and Ca increased in soil amended with sewage sludge in comparison to unamended soil. Sewage sludge amendment led to significant increase in Pb, Cr, Cd, Cu, Zn and Ni concentrations of soil. Cd concentration in soil was found above the Indian permissible limit in soil at both the amendment ratios.

The increased concentration of heavy metals in soil due to sewage sludge amendment led to increases in heavy metal uptake and shoot and root concentrations of Ni, Cd, Cu, Cr, Pb and Zn in plants as compared to those grown on unamended soil. Accumulation was more in roots than shoots for most of the heavy metals. Concentrations of Cd, Ni and Zn were more than the permissible limits of Indian standard in the edible portion of palak grown on different sewage sludge amendments ratios. Sewage sludge amendment in soil decreased root length, leaf area and root biomass of palak at both the amendment ratios, whereas shoot biomass and yield decreased significantly at 40% sludge amendment. Rate of photosynthesis, stomatal conductance and chlorophyll content decreased whereas lipid peroxidation, peroxidase activity and protein and proline contents, increased in plants grown in sewage sludge-amended soil as compared to those grown in unamended soil.

The study clearly shows that increase in heavy metal concentration in foliage of plants grown in sewage sludge-amended soil caused unfavorable changes in physiological and biochemical characteristics of plants leading to reductions in morphological characteristics, biomass accumulation and yield. The study concludes that sewage sludge amendment in soil for growing palak may not be a good option due to risk of contamination of Cd, Ni and Zn and also due to lowering of yield at higher mixing ratio.     

Digested sewage sludge solidification by converter slag for landfill cover

A new technology for solidification of digested sewage sludge referred to as converter slag solidification (CSS) has been developed using converter slag as the solidifying agent and quick lime as the solidifying aid. The CSS technology was investigated by analyzing the physicochemical properties of solidified sludge and determining its microstructural characteristics. The feasibility of using solidified sludge as a landfill cover material was considered in the context of the economical recycling of waste. Sludge solidified using the CSS technology exhibited geotechnical properties that are appropriate for replacing currently used cover soil. Microscopic analyses using XRD, SEM and EDS revealed that the main hydrated product of solidification was CSH (CaO . SiO2 . nH2O), which may play an important role in the effective setting process. Negligible leaching of heavy metals from the solidified sludge was observed. The solidification process of the hydrated sludge, slag and quicklime eliminated the coliform bacteria. Recycled sewage sludge solidified using CCS technology could be used as an effective landfill cover.     

Chicken manure increased concentration of organic sulfur compounds in field-grown onions

A field study was conducted at Kentucky State University (KSU) Research Farm. The soil in five plots was mixed with sewage sludge, five plots were mixed with yard waste compost, five plots were mixed with laying hen manure each at 15 t acre^?1, and five unamended plots that never received soil amendments were used for comparison purposes. Plots were planted with onion, Allium cepa L. var. Super Star-F1. The objectives of this investigation were to: 1) determine the concentrations of two organosulfur compounds (dipropyl disulfide and dipropyl trisulfide) in onion bulbs and 2) investigate the effect of mixing soil with three amendments (sewage sludge, yard waste, and chicken manure) on the concentration of dipropyl disulfide and dipropyl trisulfide in onion bulbs. Gas chromatographic/mass spectrometric (GC/MS) analyses of onion oil in chloroform extracts revealed the presence of two major fragment ions that correspond to dipropyl disulfide and – trisulfide. Concentration of these two organic sulfur compounds was greatest (1.5 and 0.8 mg 100 g^?1 fresh weight, respectively) in onion bulbs of plants grown in chicken manure and lowest (0.4 and 0.07 mg 100 g^?1 fresh weight, respectively) in onion bulbs of plants grown in yard waste compost treatments. We concluded that chicken manure could be exploited in growing onions with health-promoting properties.     

Emission characteristics for co-combustion of leather wastes,sewage sludge,and coal in a laboratory-scale entrained flow tube furnace

Four different mixed fuels consisted of leather waste, coal, and sewage sludge were combusted in a lab-scale entrained flow fluidized bed furnace. The influence of blending ratio on emission characteristics of SO₂, NO_x, HCl, particulate matter (PM), heavy metals, and polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) was studied. Results showed that the mixing of coal with sewage sludge had a complex effect on the emission characteristics. On the one hand, with more sewage sludge blending in the mixed fuel, the acid gas pollutant (SO₂, NO_x) decreased a lot, and the recovery of volatile heavy metals (Cd, Pb) increased at the same time. Furthermore, the leaching toxicity of Cr in the fly ash and bottom ash went down below the national standard with the adding of sewage sludge. On the other hand, the mixing of sewage sludge which consisted of more ash content resulted in the increase of the PM emission. Moreover, the high content of Cu and chlorine in the sewage sludge can promote the formation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) when the fuel 3 and 4 were combusted. Most importantly, the concentration of toxic PCDD/Fs in the flue gas produced from fuel 3 and fuel 4 was successfully controlled down below 0.20 ng I-TEQ/Nm³ by the active carbon.

     

Codisposal of municipal refuse, sewage sludge and marine dredgings for methane production

As marine disposal of sewage sludge and dredged sediments may impose serious adverse effects to marine ecosystems, landfilling seems to be the most feasible method for the final disposal of these wastes. A batch experiment was conducted to study waste degradation and gas production after sewage sludge and marine dredgings were mixed with municipal refuse at 13 different ratios for 36 days. The addition of sludge and dredgings to municipal refuse enhanced gas production, compared with the degradation of refuse or sludge alone. A proper mixing ratio of wastes can also shorten the time to reach the final phase of anaerobiosis. The highest gas production was obtained from the ratio of 75-20-5 (refuse-sludge-dredgings) (wet weight basis). Its average daily gas production rate was 1.42 l kg(-1) waste mixture; methane content was 68.3%. The results indicated that codisposal of the three wastes would be beneficial for energy recovery from landfill gas.     

A comparison between sludge ash and fly ash on the improvement in soft soil

In this study, the strength of soft cohesive subgrade soil was improved by applying sewage sludge ash as a soil stabilizer. Test results obtained were compared with earlier tests conducted on soil samples treated with fly ash. Five different proportions of sludge ash and fly ash were mixed with soft cohesive soil, and tests such as pH value, compaction, California bearing ratio, unconfined compressive strength (UCS), and triaxial compression were performed to understand soil strength improvement because of the addition of both ashes. Results indicate that pH values increase with extending curing age for soil with sludge ash added. The UCS of sludge ash/soil were 1.4-2 times better than untreated soil. However, compressive strength of sludge ash/soil was 20-30 kPa less than fly ash/soil. The bearing capacities for both fly ash/soil and sludge ash/soil were five to six times and four times, respectively, higher than the original capacity. Moreover, the cohesive parameter of shear strength rose with increased amounts of either ash added. Friction angle, however, decreased with increased amounts of either ash. Consequently, results show that sewage sludge ash can potentially replace fly ash in the improvement of the soft cohesive soil.     

Heavy metal mobility in runoff water and absorption by eggplant fruits from sludge treated soil

Sewage sludge addition to agricultural lands requires judicious management to avoid environmental risks arising from heavy metal and nitrate contamination of surface water and accumulation in edible plants. A field study was conducted on a silty-loam soil of 10% slope at Kentucky State University Research Farm. Eighteen plots of 22 x 3.7 m each were separated using metal borders and the soil in six plots was mixed with sewage sludge and yard waste compost mix (SS-YW) at 15 t acre(-1), six plots were mixed with sewage sludge (SS) at 15 t acre(-1), and six unamended plots that never received sludge were used for comparison purposes. Plots were planted with eggplant, Solanum melongena L. as the test plant. The objectives of this investigation were to: 1) assess the effect of soil amendments on the transport of NO3, NH4, and heavy metals (Cd, Cr, Ni, Pb, Zn, Cu, and Mo) into surface water; 2) investigate the effect of soil amendments on heavy metal bioavailability in eggplant fruits at harvest; and 3) assess chemical and physical properties of soil following addition of soil amendments and their impact on the yield and quality of eggplant fruit. SS-YW treatments reduced runoff water by 63% while plots incorporated with sewage sludge alone reduced runoff water by 37% compared to control treatment. The SS-YW treatments transported more mineral nitrogen (NO3-N and NH4-N) in runoff water than SS treatments. Total marketable yield (lbs acre(-1)) and number of eggplant fruits were greatest in SS-YW treatments. This response may be due to improved soil porosity, water, and nutrient retention of the soil amended with SS-YW mixture. Concentrations of heavy metals in soil amended with sludge were below the U.S. Environmental Protection Agency (USEPA) limits. Chromium, Ni, Zn, and Cu were taken up by eggplant fruits but their concentrations were below the Codex Commission allowable levels.     

Mobility of dimethoate residues from spring broccoli field

Dimethoate [O, O-dimethyl-S-(N-methylcarbamoyl-methyl) phosphorodithioate] is a broad-spectrum systemic insecticide currently used worldwide and on many vegetables in Kentucky. Dimethoate is a hydrophilic compound (log KOW = 0.7) and has the potential of offsite movement from the application site into runoff and infiltration water. The dissipation patterns of dimethoate residues were studied on spring broccoli leaves and heads under field conditions. Following foliar application of Dimethoate 4E on broccoli foliage at the rate of 0.47 L acre(-1), dimethoate residues were monitored in soil, runoff water collected down the land slope, and in infiltration water collected from the vadose zone. The study was conducted on a Lowell silty loam soil (pH 6.9) planted with broccoli under three soil management practices: (i) soil mixed with municipal sewage sludge, (ii) soil mixed with yard waste compost, and (iii) no-mulch rototilled bare soil. The main objective of this investigation was to study the effect of mixing native soil with municipal sewage sludge or yard waste compost, having considerable amounts of organic matter, on off-site movement of dimethoate residues into runoff and infiltration water following spring rainfall. The initial deposits of dimethoate were 6.2 and 21.4 micro g g(-1) on broccoli heads and leaves, respectively. These residues dissipated rapidly and fell below the maximum residue limit of 2 micro g g(-1) on the heads and leaves after 10 and 14 d, respectively, with half-lives of 5.7 d on broccoli heads and 3.9 d on the leaves. Dimethoate residues detected in top 15 cm of soil (due to droplet drift and wash off residues from broccoli foliage) one day (d) following spraying, were 30.5 ng g(-1) dry soil in the sewage sludge treatment, and 46.1 and 134.5 ng g(-1) dry soil in the yard waste and no mulch treatments, respectively. Water infiltration was greater from yard waste compost treatment than from no mulch treatment, however concentrations of dimethoate in the vadose zone of the three soil treatments did not differ.     

Effects of sewage sludge biochar on plant metal availability after application to a Mediterranean soil

Pyrolytic conversion of sewage sludge into biochar could be a sustainable management option for Mediterranean agricultural soils. The aim of this work is to evaluate the effects of biochar from sewage sludge pyrolysis on soil properties; heavy metals solubility and bioavailability in a Mediterranean agricultural soil and compared with those of raw sewage sludge. Biochar (B) was prepared by pyrolysis of selected sewage sludge (SL) at 500 °C. The pyrolysis process decreased the plant-available of Cu, Ni, Zn and Pb, the mobile forms of Cu, Ni, Zn, Cd and Pb and also the risk of leaching of Cu, Ni, Zn and Cd. A selected Mediterranean soil was amended with SL and B at two different rates in mass: 4% and 8%. The incubation experiment (200 d) was conducted in order to study carbon mineralization and trace metal solubility and bioavailability of these treatments. Both types of amendments increased soil respiration with respect to the control soil. The increase was lower in the case of B than when SL was directly added. Metals mobility was studied in soil after the incubation and it can be established that the risk of leaching of Cu, Ni and Zn were lower in the soil treated with biochar that in sewage sludge treatment. Biochar amended samples also reduced plant availability of Ni, Zn, Cd and Pb when compared to sewage sludge amended samples.