Infrared and nuclear magnetic resonance evidence of degradation in thermoplastics based on forest products

The degradation of lignin-(1-phenylethylene) graft copolymers (lignin-styrene graft copolymers) by white rot basidiomycete fungi was followed by monitoring aromatic absorption bands by Fourier transform infrared (FTIR) spectroscopy and nuclear magnetic resonance (NMR) spectroscopy. The FTIR of the graft copolymers shows a series of characteristic absorbance peaks from multi-substituted aromatic rings and a strong poly(1-phenylethylene) (polystyrene) absorbance peak from monosubstituted aromatic rings. Subtraction of copolymer spectra taken before incubation from spectra taken after 50 days of incubation with the four tested fungi shows the loss of functional groups from the copolymer. NMR spectra also show reduction of aromatic ring resonances from the copolymer and incorporation of peaks from fungi as a result of incubation with fungi. The biodegradation tests were run on lignin-(1-phenylethylene) graft copolymers which contained 10.3, 32.2, and 50.4% of lignin. The polymer samples were incubated with the white rot fungiPleurotus ostreatus, Phanerochaete chrysosporium, andTrametes versicolor, and the brown rot fungusGleophyllum trabeum. White rot fungi degraded the plastic samples at a rate that increased with increasing lignin content in the copolymer sample. Both poly(1-phenylethylene) and lignin components of the copolymer were readily degraded. Observation by scanning electron microscopy of incubated copolymers showed a deterioration of the plastic surface. The brown rot fungus did not affect any of these plastics, nor did any of the fungi degrade pure poly(1-phenylethylene).Paper presented at the Bio/Environmentally Degradable Polymer Society—Second National Meeting, August 19–21, 1993, Chicago, Illinois.     

Novel Environmentally Friendly Copolymers Carboxymethyl Starch Grafted Poly(Lactic Acid)

Modified natural polymers have been gaining increasing scientific interest for many years. In this study carboxymethyl starch (CMS) was grafted with L(+)-lactic acid (LA) in different molar ratios CMS/LA (1/36, 1/22 and 1/12), resulting carboxymethyl starch-g-poly(lactic acid) (CMS-g-PLA) copolymers. The grafting reaction was carried out by solution polycondensation procedure in toluene and stannous 2-ethyl hexanoate Sn(Oct)₂ as catalyst was utilized. Poly(lactic acid) (PLA) was synthesized in the same conditions with the copolymers for comparative analyses of the physico-chemical and thermal properties. The copolymers and PLA were structurally and morphologically characterized by FT-IR, ¹H-NMR spectroscopy, WAXD and SEM analyses, taking CMS as reference. The molecular weight of the copolymers, CMS and PLA were determined, using a dynamic light scattering technique. The thermal behavior of the products was studied by DSC and TG-DTG analyses. The CMS-g-PLA graft copolymers exhibited lower Tg and thermal stability than pure CMS.     

Photo-/Bio-degradability of Agro Waste and Ethylene–Propylene Copolymers Composites Under Abiotic and Biotic Environments

Composites were prepared by two methods, (i) graft copolymerization (GFC) of isotactic polypropylene (PP) with maliec anhydride, (MAH) followed by esterification with coir fiber and (ii) by direct reactive mixing (DFC) of polypropylene (PP) and ethylene–propylene (EP) copolymers with MAH and peroxide with coir fiber. These composites, after molding in films (5×5 cm, m thickness) were examined for susceptibility to biological attack by measuring the percentage weight loss in compost upto 6 months, periodically, and fungal colonization on surface of the samples, when kept as sole carbon source for the growth of Aspergillus niger in culture medium upto 40 days. Photodegradation was evaluated by monitoring the variations in FT-IR spectrum and crack formation after successive treatment with UV light (≥290 nm) for 0, 20, 50 and 100 h at 60°C in the presence of air. Specimens of virgin PP were taken as a reference during all period of photo and biodegradation studies. Significant changes were observed depending on the preparation methods during photodegradation and biodisintegration of composites. DFCs samples were disintegrated faster than GFCs during the composting whereas, in culture, GFCs were covered highly in well uniform way by fungi. It was observed that photo-oxidative ageing directly enhanced the biodegradability of composites as the increase in fungal growth rate and decrease in weight during composting were found. It was concluded that extent of compatibilization had a profound effect on photo-oxidation and biodisintegration of composite material; consequently ester bonds were main units during fungal consumption. Composition of monomers in copolymers was also showing significant effect on the degradability which decreased with increasing content of ethylene in ethylene–propylene (EP) copolymers.     

Graft Copolymerization of Methyl Acrylate onto Cellulosic Biofibers: Synthesis,Characterization and Applications

Graft copolymerization of cellulosic biopolymers with synthetic polymers is of enormous interest because of its application in biofiltration, biosorption, biomedical, biocomposites and various other eco-friendly materials. Synthesis of graft copolymers of methyl acrylate onto mercerized Grewia optiva biofibers using ferrous ammonium sulfate–potassium per sulfate as redox initiator in air was carried out. Different reaction parameters such as amount of solvent, monomer concentration, initiator molar ratio, reaction time and reaction temperature were optimized to get the maximum percentage of grafting. The graft copolymers thus formed were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, differential thermal analysis and differential thermogravimetric techniques. A plausible mechanism for explanation of the graft copolymerization reactions pattern shown is offered. The effect of grafting percentage on the physico–chemical properties of raw as well as grafted Grewia optiva biofibers has also been investigated. The graft copolymers have been found to be more moisture resistant and also showed better chemical and thermal resistance. Green polymer composites were also successfully prepared through compression molding technique by using grafted Grewia optiva biofibers as reinforcement.     

Comparison of Cationic and Unmodified Starches in Reactive Extrusion of Starch–Polyacrylamide Graft Copolymers

Graft copolymers of starch and polyacrylamide (PAAm) were prepared using reactive extrusion in a corotating twin screw extruder. The effect of cationic starch modification was examined using unmodified and cationic dent starch (≈23% amylose) and waxy maize starch (≈2% amylose). For a fixed acrylamide/starch feed ratio, conversion, graft content, and grafting efficiency were essentially unaffected by starch type or modification. Cationic starch graft copolymers generally had lower molecular weight PAAm grafts compared to the unmodified starch, whereas amylose content had little or no significant effect. In addition, the frequency of grafting was higher with cationic starch. These results indicate that cationic modification of starch enhances formation of grafting sites, resulting in graft copolymers with more grafts of lower molecular compared to unmodified starch. Cationic modification may therefore be a way to tailor the properties of starch–PAAm graft copolymers.     

Combining Renewable Ethyl Cellulose and Acrylate to Fabricate Sustainable TPEs via Controlled Polymerization

Journal of Polymers and the Environment - A series of ethyl cellulose (EC) grafted copolymers were fabricated with methyl methacrylate (MMA), stearyl methacrylate (SMA) and EC grafted...     

Microbial degradation of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) in compost

The microbial degradation of tensile test pieces made of poly(3-hydroxybutyrate) [P(3HB)] or copolymers with 10% [P(3HB-co-10%3HV)] and 20% [P(3HB-co-20%3HV)] 3-hydroxyvaleric acid was studied in small household compost heaps. Degradation was measured through loss of weight (surface erosion) and changes in molecular weight and mechanical strength. It was concluded, on the basis of weight loss and loss of mechanical properties, that P(3HB) and P(3HB-co-3HV) plastics were degraded in compost by the action of microorganisms. No decrease inM _w could be detected during the degradation process. The P(3HB-co-20%3HV) copolymer was degraded much faster than the homopolymer and P(3HB-co-10%3HV). One hundred nine microbial strains capable of degrading the polymersin vitro were isolated from the samples used in the biodegradation studies, as well as from two other composts, and identified. They consisted of 61 Gram-negative bacteria (e.g.,Acidovorax facilis), 10 Gram-positive bacteria (mainlyBacillus megaterium), 35Streptomyces strains, and 3 molds.     

Synthesis and biodegradation of poly(γ-butyrolactone-co-l-lactide)

Biodegradable polyesters were synthesized by ring-opening copolymerization of -butyrolactone (BL) and its derivatives withl-lactide (LLA). Although tetraphenyl tin was the main catalyst used, other organometallic catalysts were used as well.¹H and¹³C NMR spectra showed that poly(BL-co-LLA)s were statistical and that their number-average molecular weights were as high as 7×10⁴. The maximum BL content obtained from copolymerization BL/LLA was around 17%. TheT _m andT _g values of the copolymers showed a gradual depression with an increase in BL content. NoT _m was obtained for the copolymers containing more than 13 mol% BL. The biodegradability of the copolyesters was evaluated by enzymatic hydrolysis and nonenzymatic hydrolysis tests. The enzymatic hydrolysis was carried out at 37°C for 24 h using lipases fromRhizopus arrhizus andR. delemar. Hydrolyses by both lipases showed that an increase in BL content of the copolymer resulted in enhanced biodegradability. Nonenzymatic accelerated hydrolysis of copolymers at 70°C was found to increase proportionally to their exposure time. The hydrolysis rate of these copolymers was considerably faster than that of PLLA. The higher hydrolyzability was recorded for the BL-rich copolymers. The copolymerization of -methyl--butyrolactone (MBL) or -ethyl--butyrolactone (EBL) with LLA resulted in relatively LA-rich copolymers.     

Synthesis, Characterization, and Hydrolytic Degradation of Copolymers of 2-Methylene-1,3-dioxepane with Ethylene and with Styrene

2-Methylene-1,3-dioxepane (MDP) was copolymerized with ethylene (E) at a pressure of approximately 1000 psi and a temperature of approximately 70°C with AIBN as the free radical initiator. The copolymers obtained, poly(MDP-co-E), were characterized by elemental analysis, IR, ¹H-NMR and ¹³C-NMR spectroscopy, DSC, and GPC. The copolymers contained 2–15 mol% ester units. MDP was also copolymerized with styrene (S) at 120°C with di-t-butyl peroxide as the initiator to prepare the copolymer, poly(MDP-co-S). The number-average molecular weights of both types of copolymers were in the range of 6000 to 11,000, and the weight-average molecular weights were in the range of 9000 to 17,000. The melting temperatures of poly(MDP-co-E) decreased with increasing ester unit content in the copolymer. For the MDP-S copolymers, the glass transition temperatures decreased with increasing ester unit content. Both poly(MDP-co-E) and poly(MDP-co-S) were degraded by methanolysis, and their molecular weights decreased by the expected amounts based on the ester unit content.     

Properties and biodegradability of chain-extended copoly(succinic anhydride/ethylene oxide)

Chain-extension reactions were carried out using titanium-iso-propoxide (TIP) as a catalyst for a series of polyesters or copolyesterethers with low molecular weights (M _n =1500–10,000) synthesized by the ring-opening copolymerization of succinic anhydride (SA) with ethylene oxide (EO). The copolymers having aM _n from 25,000 to 50,000 of different properties were obtained. Both the melting point (T _m ) and the fusion heat (H), which indicate the crystallinity of the copolymers, rose with an increase in SA content in the copolymers. Semitransparent films were prepared by compression molding of the copolymers. The biodegradation of the copolymer films was evaluated by enzymatic hydrolysis by lipases and by an aerobic gas evolution test in standard activated sludge. The hydrolyzability of these copolymers by three kinds of lipases was affected by their copolymer composition SA/EO, form, andM _n . The copolyesterether (SA/EO=43/57,M _n =48,900) was more easily biodegraded by standard activated sludge compared to the polyester (SA/EO=47/53,M _n =36,300).Presented at the Pacifichem-95, December 17–22, 1995, Honolulu, Hawaii.     

Biodegradation of pretreated polyethylene film by Pseudomonas aeruginosa AMB-CD-1

A comparative study evaluated the acid, alkali, and heat-treated polyethylene biodegradation efficiency of Pseudomonas aeruginosa AMB-CD-1. The polyethylene (PE) pieces were separately treated with heat (50°C), acid (1N HCl), and alkali (1N NaOH) and then washed with water before use. All the treated samples were analyzed through thermogravimetric analysis. In addition, weight and temperature changes during the decomposition reactions were also measured and determined. In these treatments, the PE films of heat-treated and acid-treated low-density polyethylene (LDPE) indicated more significant weight loss at 120°C (48.99% and 40.75%, respectively) as compared to their control or untreated PE and alkali-treated LDPE (21.84% and 24.68%, respectively). A biodegradation assay was then conducted with treated and untreated LDPE films with P. aeruginosa AMB-CD-1 strain. Fourier transform infrared spectroscopy analysis revealed that the heat or acid-pretreated samples with isolate AMB-CD-1 displayed peaks at 2922.84, 2923.97, and 1450.31, 874.22 cm⁻¹ for C–H stretching deformation vibration, CH₂ scissoring vibration, –CHO stretching, and strong alkyl structure, respectively. Furthermore, the new peaks with a significant difference at 2500–2000 cm⁻¹ (O═C═O, O–H stretching vibration: carboxylic acid) and 1500–1000 cm⁻¹ (–CHO and C═O stretching) were noticed in the infrared spectral range of LDPE degradation. Modifications in the functional group provided evidence that biodegradation had impacted the chemical structure of the LDPE film. Additionally, it was demonstrated that pretreating LDPE films with heat or acid could speed up their biodegradation.     

Selective Lead(II) Adsorption and Flocculation Characteristics of the Grafted Sodium Alginate: A Comparative Study

Synthesis of sodium alginate-g-poly(acrylamide-co-N-methylacrylamide) [S-III], sodium alginate-g-poly(N-methylacrylamide-co-N,N-dimethylacrylamide) [S-II], sodium alginate-g-poly(acrylamide-co-N,N-dimethylacrylamide) [S-I]. Sodium alginate-g-poly(N,N-dimethylacrylamide) [SAG-g-PDMA] and sodium alginate-g-poly(acrylamide) [SAG-g-PAM] were prepared by solution polymerization technique using potassium peroxydisulfate as the initiator at 70?°C in water medium. The graft copolymers were characterized by FTIR and NMR (¹H and ¹³C) spectroscopy, SEM and XRD studies. All the five graft copolymers were used to remove Pb(II) ions from the aqueous solution and also in flocculation studies of kaolin clay (1.0 wt%), silica (1.0 wt%) and iron ore slime (0.25 wt%) suspensions. A comparative studies of all the five graft copolymers were also made in both the two cases. The Pb(II) ion removal capacity of all the graft copolymers follows the order S-III?>?SAG-g-PAM?>?S-II?>?SAG-g-PDMA?>?S-I. But the flocculation performance of the graft copolymers follows the order S-II?>?S-I?>?S-III?>?SAG-g-PDMA?>?SAG-g-PAM. S-III was also used for the competitive metal ion removal with Hg(II), Cd(II), Cu(II) and Zn(II). Pb(II) adsorption of S-III (the best Pb(II) ion adsorber) follows pseudo second order rate equation and Langmuir adsorption isotherm.     

A Novel Biodegradable Green Poly(l-Aspartic Acid-Citric Acid) Copolymer for Antimicrobial Applications

Poly (l-aspartic acid-citric acid) green copolymers were developed using thermal polymerization of aspartic acid (ASP) and citric acid (CA) followed by direct bulk melt condensation technique. Antibacterial properties of copolymer of aspartic acid based were investigated as a function of citric acid content. This study is focused on the microorganism inhibition performance of aspartic acid based copolymers. Results showed that inhibition properties increase with increasing citric acid content. Characterization of obtained copolymers was carried out with the help of infrared absorption spectra (FTIR), x-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermo gravimetric analysis (TGA). The antibacterial activity of copolymers against bacteria like E-coli, Bacillus and pseudomonas was investigated. The copolymers showed excellent antimicrobial activities against three types of microorganisms. Overall studies indicated that the above copolymers possess a broad wound dressing activity against above three types of bacteria and may be useful as antibacterial agents.     

Biomedical Textiles Through Multifunctioalization of Cotton Fabrics Using Innovative Methoxypolyethylene Glycol-N-Chitosan Graft Copolymer

Multifunctioalization of cotton fabrics was developed by a novel finishing formulation. The method is based on chitosan-N-polyethylene glycol graft copolymer along with citric acid and sodium hypophosphite (SHP) as catalysts. Treatment of the cotton fabric resulted in the chemical attachment of the copolymer to the cotton fabric via bridging-based esterification where the latter involves reaction of one molecule of the polycarboxylic acid (citric acid) with both the amino group of the copolymer and the hydroxyl groups of cotton. Inclusion of the copolymer in the crosslinked structure of cotton as well as by hydrogen bonding and van der Waals forces are additionally possible. Synthesis of the copolymer was raised out by the reaction of chitosan with methoxy polyethylene glycol (MPEG) aldehyde followed by the reduction with sodium borohydride. MPEG was prepared by oxidation of PEG with acetic anhydride in dimethyl sulphoxide at room temperature. Methoxypolyethylene glycol-N-chitosan graft copolymer (MPEG-N-CTS) structure was confirmed by IR, NMR, X-RD and TGA techniques. The copolymer is soluble in water. The pad dry-cure method was used for the cotton fabrics treatment with aqueous solution of prepared copolymer along with citric acid and SHP. The so treated fabrics were monitored for copolymer content (expressed as N%), crease recovery, tensile strength, elongation at break, air permeability, water permeability, roughness, bursting strength and antibacterial activity. Fabric performances based on the outputs of these measurements advocate these multifunctionalized fabrics for use as medical textile.     

Bacterial Poly(Hydroxyalkanoate) Polymer Production from the Biodiesel Co-product Stream

A co-product stream from soy-based biodiesel production (CSBP) containing glycerol, fatty acid soaps, and residual fatty acid methyl esters (FAME) was utilized as a fermentation feedstock for the bacterial synthesis of poly(3-hydroxybutyrate) (PHB) and medium-chain-length poly(hydroxyalkanoate) (mcl-PHA) polymers. Pseudomonas oleovorans NRRL B-14682 and P. corrugata 388 grew and synthesized PHB and mcl-PHA, respectively, when cultivated in up to 5% (w/v) CSBP. In shake flask culture, P. oleovorans grew to 1.3 ± 0.1 g/L (PHA cellular productivity = 13–27% of the bacterial cell dry weight; CDW) regardless of the initial CSBP concentration, whereas P. corrugata reached maximum cell yields of 2.1 g/L at 1% CSBP, which tapered off to 1.7 g/L as the CSBP media concentration was increased to 5% (maximum PHA cellular productivity = 42% of the CDW at 3% CSBP). While P. oleovorans synthesized PHB from CSBP, P. corrugata produced mcl-PHA consisting primarily of 3-hydroxyoctanoic acid (C_8:0; 39 ± 2 mol%), 3-hydroxydecanoic acid (C_10:0; 26 ± 2 mol%) and 3-hydroxytetradecadienoic acid (C_14:2; 15 ± 1 mol%). The molar mass (M_n) of the PHB polymer decreased by 53% as the initial CSBP culture concentration was increased from 1% to 5% (w/v). In contrast, the M_n of the mcl-PHA polymer produced by P. corrugata remained constant over the range of CSBP concentrations used.     

Influence of Processing Additives on the Degradation of Melt-Pressed Films of Poly(ε-Caprolactone) and Poly(Lactic Acid)

Melt-pressed films of polycaprolactone (PCL) and poly(lactic acid) (PLA) with processing additives, CaCO₃, SiO₂, and erucamide, were subjected to pure fungal cultures Aspergillus fumigatus and Penicillium simplicissimum and to composting. The PCL films showed a rapid weight loss with a minor reduction in the molecular weight after 45 days in A. fumigatus. The addition of SiO₂ to PCL increased the rate of (bio)erosion in A. fumigatus and in compost. The use of a slip additive, erucamide, was shown to modify the properties of the film surface without decreasing the rate of bio(erosion). Both the rate of weight loss and the rate of molecular weight reduction of PCL increased with decreasing film thickness. The addition of CaCO₃ to PLA significantly reduced the thermal degradation during processing, but it also reduced the rate of the subsequent (bio)degradation in the pure fungal cultures. PLA without additives and PLA containing SiO₂ exhibited the fastest (bio)degradation, followed by PLA with CaCO₃. The degradation of the PLA films was initially governed by chemical hydrolysis, followed by an acceleration of the weight change and of the molecular weight reduction. PLA film subjected to composting exhibits a rapid decrease in molecular weight, which then remains unchanged during the measurement period, probably because of crystallization.     

Syntheses of Biodegradable Functional Polymers by Radical Ring-Opening Polymerization of 2-Methylene-1,3,6-trioxocane

2-Methylene-1,3,6-trioxocane (MTC) was polymerized via ring-opening in the presence of a radical initiator and the obtained polyester was biodegradable. MTC could also copolymerize with various vinyl monomers such as styrene, vinyl acetate, methyl vinyl ketone, N-vinyl-2-pyrrolidone, N-isopropyl acrylamide, and maleic anhydride. By copolymerizing MTC with these vinyl monomers in the presence of a radical initiator, we could obtain various biodegradable polymers with ester group introduced into the backbone. In addition the obtained copolymers exhibit certain functionalities such as photolysis, water-solubility, thermosensitivity, detergent builder, and water-absorbability.     

Mechanical Properties and Lipase-Catalyzed Biodegradation of α-Methyl, ε-Caprolactone/ ε-Caprolactone Copolymers Obtained by Chemical Modification of Poly(ε-caprolactone)

Novel (-caprolactone)-based copolymers of different compositions were synthesized by allowing methyl iodide to react with the polycarbanion that resulted from the action of lithium diisopropylamide on poly(-caprolactone) in THF at –70°C under argon atmosphere. The copolymers were characterized by various techniques, namely ¹H nuclear magnetic resonance, size exclusion chromatography, differential scanning calorimetry, x-ray diffraction and viscoelasticimetry. They were submitted to hydrolytic and lipase-catalyzed enzymatic degradation in comparison with genuine PCL. The Young modulus depended on the degree of methylation. In contrast, loss angle and glass transition temperature did not depend on this parameter. It is shown that the lipase-catalyzed degradation of methylated PCL is much slower than in the case of genuine PCL.     

Influence of Short Central PEO Segment on Hydrolytic and Enzymatic Degradation of Triblock PCL Copolymers

Hydrolytic, enzymatic degradation and composting under controlled conditions of series of triblock PCL/PEO copolymers, PCEC, with central short PEO block (M _n 400 g/mol) are presented and compared with homopolymer (PCL). The PCEC copolymers, synthesized via ring-opening polymerization of ε-caprolactone, were characterized by ¹H NMR, quantitative ¹³C NMR, GPC, DSC and WAXS. The introduction of the PEO central segment (<?2 wt%) in PCL chains significantly affected thermal degradation and crystallization behavior, while the hydrophobicity was slightly reduced as confirmed by water absorption and moisture uptake experiments. Hydrolytic degradation studies in phosphate buffer after 8 weeks indicated a small weight loss, while FTIR analysis detected changes in crystallinity indexes and GPC measurements revealed bulk degradation. Enzymatic degradation tested by cell-free extracts containing Pseudomonas aeruginosa PAO1 confirmed high enzyme activity throughout the surface causing morphological changes detected by optical microscopy and AFM analysis. The changes in roughness of polymer films revealed surface erosion mechanism of enzymatic degradation. Copolymer with the highest content of PEO segment and the lowest molecular weight showed better degradation ability compared to PCL and other copolymers. Furthermore, composting of polymer films in a model compost system at 37 °C resulted in significant degradation of the all synthesized block copolymers.