热解析-固相微萃取-气相色谱法测定空气样品中挥发性有机化合物

建立了热解析-固相微萃取-气相色谱法测定空气样品中挥发性有机化合物的分析方法，并对色谱分离条件、玻璃针筒保存样品的稳定性、固相微萃取萃取纤维、萃取时间、色谱进样时间等条件进行了优化，9种挥发性有机化合物的峰面积与其质量浓度在所测范围内有较好的线性关系，相对标准偏差＜8.8%，检出限为0.05～0.75 μg/100 mL，满足实际空气样品测定需要。     

有机改性剂对水中有机氯农药提取效率的影响研究

通过有机改性剂在液液萃取和固相萃取条件下水中有机氯农药的提取效率比对分析,首次探讨了有机改性剂对水中有机氯农药提取效率的影响。结果表明,(1)液液萃取前处理水样中不加有机改性剂、固相萃取前处理水样中添加一定量有机改性剂时,水中有机氯农药的提取效率较高;(2)采用正交实验优化水中有机氯农药固相萃取的提取效率实验表明,有机改性剂添加量对其影响大于有机改性剂种类对其影响;最佳优化方案为水样中添加1%甲醇时,提取效率最高。     

银纳米粒子作为二苯并噻吩固相萃取剂的研究

以银纳米粒子为对象,开展其作为新型固相萃取填料的二苯并噻吩类化合物的固相萃取-气相色谱快速分析方法的初步研究。采用液相化学还原法合成银纳米粒子及扫描电子显微镜表征银纳米粒子,研究了银纳米粒子对二苯并噻吩的吸附动力学和热力学特征;在前面的基础之上,用固相萃取法对样品中的二苯并噻吩进行快速定量。     

固相萃取-气相色谱/质谱法测定水中多环芳烃

建立了固相萃取-气相色谱／质谱联用测定水中多环芳烃(PAHs)的分析方法．优化了固相萃取条件。结果表明,固相萃取效率高、萃取时间短,采用MS的选择离子检测方式对实际水样中PAHs进行定性定量分析,平均回收率在80．4％～115％之间,相对标准偏差为7．03％～18．5％,方法的检出限在0．010～0．020μg／L之间。通过实际样品中PAHs的分析表明,该法快速,溶剂用量少,能满足痕量分析的要求。     

固相微萃取-毛细管气相色谱法快速分析水中酞酸酯

用固相微萃取富集水中酞酸酯，毛细管气相色谱分离分析，整个分析过程只需50min，检出限可达0.01-40.0μg／L，实验表明，固相微萃取是一种快速、简便、集萃取浓缩进样于一体的样品前处理技术，具有分析时间短、灵敏度高、无需有机溶剂的优点，已用于地面水源、海水、饮用水中酞酸酯含量的测定。     

液液萃取 — 超高效液相色谱 — 三重四级杆质谱测定地表水中19种磺胺类药物残留

建立了液液萃取—超高效液相色谱—三重四级杆质谱技术,测定地表水中19种磺胺类药物。通过乙酸乙酯超声萃取水样中的磺胺类药物,并用0.1%(体积分数)甲酸水溶液-甲醇作为流动相,C18色谱柱分离,在多反应监测(MRM)模式下测定。优化了萃取剂种类和用量、超声时间、流动相的组成等条件。在优化条件下,19种磺胺类药物在0.1～40.0μg/L范围内线性良好且相关系数均大于0.999 0,方法检出限为0.02～0.80ng/L,平均回收率为73.5%～92.8%,相对标准偏差为1.2%～8.7%。该方法操作简单、灵敏度高、所需样品及有机溶剂少,适用于实际的分析检验工作。     

饮用水中异嗅物质-土臭素及二甲基异冰片的测定方法

导致饮用水土霉味的常见物质为土臭素(GSM)和二甲基异冰片(2-MIB),此两种物质通常在原水及饮用水中痕量存在,浓度低于几百ng/L.总结了用感官分析法和仪器分析法测定痕量GSM和2-MIB.对液液萃取、固相萃取、固相微萃取及各种衍生水样预处理方法进行了对比,评价了各种方法的优劣,并对异嗅物质分析方法的发展提出了展望.     

固相萃取-毛细管气相色谱法测定蔬菜、土壤和水中的毒死蜱残留量

采用固相萃取技术提取蔬菜、土壤和水体中毒死蜱,建立了蔬菜、土壤和水体中毒死蜱的固相萃取-气相色谱测定方法,并与传统方法进行了比较。添加浓度为0.1、1、10 mg·L-1,两种方法的水样平均回收率分别在93.7%~102.7%和96.2%~100.2%,变异系数分别在2.2%~7.7%和3.3%~5.1%;土壤平均回收率分别在91.3%~100.7%和92.0%~104.8%,变异系数分别在1.4%~7.0%和0.3%~5.2%;蔬菜平均回收率分别在89.4%~101.4%和92.5%~101.8%,变异系数分别在5.2%~7.1%和3.1%~6.0%。试验结果表明,固相萃取法与传统方法的回收率和变异系数相当,但前者更加省时、省力和省溶剂。     

固相萃取与气相色谱-质谱联用测定水中痕量多环芳烃

采用固相萃取与气相色谱-质谱联用测定水中痕量多环芳烃(PAHs)。通过正交试验,得到最佳固相萃取条件为:上样流速为5mL/min、采用二氯甲烷洗脱、洗脱剂用量为3mL、洗脱流速为2mL/min。测定结果显示,固相萃取与气相色谱—质谱联用技术对萘、菲、荧蒽3种PAHs的检出限为0.03～0.07μg/L,加标回收率为70%～100%,相对标准偏差为3.90%～9.58%。该方法精密度高、准确度好,能满足实际水样中痕量PAHs的测定要求。     

固相萃取毛细管气相色谱法分析水中有机磷农药残留

探索了采用固相萃取对样品进行提取富集，以及配备氮磷检测器的毛细管气相色谱(CGC)法分析水中有机磷农药痕量残留的方法。结果表明：敌敌畏、内吸磷、乐果、甲基对硫磷、马拉硫磷和对硫磷等6种农药在20min内有较好的分离；3个不同浓度的标准添加，其回收率范围为52．1％～93．7％，最低检出限范围为1．11～5．21ng／L；同时利用该方法分析太湖梅梁湾水源地和长江沿岸水厂取水口水质，6种有机磷农药均有一定程度检出，但仍未超出集中水源地供水标准。     

A multi-residue method for the analysis of organophosphorus residues in cooked and polished rice using accelerated solvent extraction and dispersive-solid phase extraction (D-SPE) technique and uncertainty measurement

Quick, simple and efficient multi-residue analytical methods were developed and validated for the determination of organophosphorous insecticides from polished and cooked rice. Polished rice was extracted using a simple, automated technique namely accelerated solvent extraction (ASE) using dichloromethane as the extraction solvent. Cooked rice was extracted with acetone and cleaned up using dispersive-solid phase extraction (D-SPE) technique. The single step extraction method adopted for polished rice using accelerated solvent extractor provided satisfactory recovery for eight organophosphorus pesticides (OPPs) which ranged from 85.5–116.7%; 90.0–110.3% and 93.5–118.8% at 1, 5 and 10 limit of quantification (LOQ) levels, respectively. The recovery of cooked rice was in the range of 74–124%; from 75–100% and from 73–87% for 1, 5 and 10 level of fortification, respectively. The total uncertainty was evaluated, taking four main independent sources viz., weighing, purity of the standard, GC calibration curve and repeatability under consideration. The expanded uncertainty was found to be in the range of 5–20%.     

Determination of phenolic and steroid endocrine disrupting compounds in environmental matrices

BACKGROUND, AIM AND SCOPE: Many pollutants have received significant attention due to their potential estrogenic effect and are classified as endocrine disrupting compounds (EDCs). EDCs comprise many classes of organic compounds. The development or optimization of analytical protocols for the simultaneous determination of EDCs in environmental samples is an analytical challenge because these compounds exhibit different physicochemical characteristics, they occur in the aquatic environment in relatively low concentrations and, furthermore, environmental samples are considered as complex matrices. The aim of this study is the development of analytical methods for the simultaneous determination of phenolic and steroid EDCs in aqueous and solid samples. The target compounds are 4-nonylphenol, 4-octylphenol, their ethoxylate oligomers (mono- and di-ethoxylates of nonylphenol and octylphenol), bisphenol A, the estrogens (estriol, estrone, 17beta-estradiol, 17alpha-estradiol) and the synthetic steroids (mestranol and 17alpha-ethynylestradiol). MATERIALS AND METHODS: Solid phase extraction employing Oasis HLB cartridges and different elution solvents was used for the recovery studies of the target compounds from various types of water samples (ultrapure water, artificial seawater, river water and seawater). Ultrasonic assisted extraction was applied for the recovery of the target EDCs from the solid samples. The recoveries were assessed using various solvents for the extraction and the elution of EDCs from different SPE cartridges used for clean up. Gas chromatography-mass spectrometry after derivatization with N,O-bis(trimethylsilyl)-trifluoroacetamide was employed for the determination of these compounds. RESULTS AND DISCUSSION: The recovery rates of three elution solvents (methanol, acetone and ethylacetate) for the extraction of target EDCs from artificial seawater were assessed after preconcentration on SPE cartridges. Acetone showed better recoveries and was further tested for its extraction efficiency in different water types (river water, seawater). Ultrasonic assisted extraction was used for the recovery of target EDCs from solid matrices. Acetone, methanol, mixture of acetone-methanol (1:1) and ethylacetate were used as extraction solvents. Ethylacetate and the mixture of acetone-methanol (1:1) exhibited better extraction efficiencies. An additional clean up step was necessary for sediment samples. Different SPE cartridges were employed for clean up of the extracts (Oasis HLB, C18, Florisil, silica, combination of silica and alumina). Florisil cartridges were finally used. The proposed methods were further validated on the determination of target EDCs in field collected samples (river water, seawater, wastewater, total suspended solids and sediments) from the major area of Thessaloniki, Greece. CONCLUSIONS: Efficient and accurate integrated methods for the simultaneous determination of alkylphenols (nonylphenol, octylphenol), their ethoxylate oligomers (mono- and di-ethoxylate of nonylphenol and octylphenol), bisphenol A and steroids (estriol, estrone, 17beta-estradiol, 17alpha-estradiol, mestranol and 17alpha-ethynylestradiol) in aqueous and solid samples were developed. The proposed methods were applied for the determination of the target compounds in representative environmental samples in the area of Thessaloniki, Northern Greece. RECOMMENDATIONS AND PERSPECTIVES: This study confirms the occurrence of selected EDCs in inland and marine waters in the area of Thessaloniki, Northern Greece. Since there is no previous data on the occurrence of the target EDCs in the major area, an extended survey is in progress to evaluate the occurrence and fate of these compounds.     

Application of QuEChERS method and gas chromatography-mass spectrometry for the analysis of cypermethrin residue in milk

Analytical methods for the isolation and determination of cypermethrin in milk, based on the solid-phase microextraction (SPME) and QuEChERS methods (Quick, Easy, Cheap, Effective, Rugged, and Safe) are presented. The SPME technique was not appropriate to analyse cypermethrin in milk, even establishing the best extraction conditions, polydimethylsiloxane fiber, 60 min time extraction, 60 °C temperature extraction, addition of salt (NaCl) and stirring rate. The extraction efficiency was low probably because of the matrix constituents. The QuEChERS method involves the extraction of the analyte with acetonitrile and simultaneous liquid-liquid partitioning formed by adding anhydrous MgSO(4) plus NaCl, followed by the removal of residual water and cleanup using a procedure called dispersive solid-phase extraction, in which anhydrous MgSO(4) plus PSA and C18 are mixed with 1 mL of acetonitrile extract. The detection and quantification limits were 0.01 and 0.04 mg kg(-1), respectively, and the percentage recovery obtained ranged from 92 to 105% with relative standard deviations below 7%.     

Application of QuEChERS method and gas chromatography-mass spectrometry for the analysis of cypermethrin residue in milk

Analytical methods for the isolation and determination of cypermethrin in milk, based on the solid-phase microextraction (SPME) and QuEChERS methods (Quick, Easy, Cheap, Effective, Rugged, and Safe) are presented. The SPME technique was not appropriate to analyse cypermethrin in milk, even establishing the best extraction conditions, polydimethylsiloxane fiber, 60 min time extraction, 60 °C temperature extraction, addition of salt (NaCl) and stirring rate. The extraction efficiency was low probably because of the matrix constituents. The QuEChERS method involves the extraction of the analyte with acetonitrile and simultaneous liquid-liquid partitioning formed by adding anhydrous MgSO₄ plus NaCl, followed by the removal of residual water and cleanup using a procedure called dispersive solid-phase extraction, in which anhydrous MgSO₄ plus PSA and C18 are mixed with 1 mL of acetonitrile extract. The detection and quantification limits were 0.01 and 0.04 mg kg^?1, respectively, and the percentage recovery obtained ranged from 92 to 105% with relative standard deviations below 7%.     

Total and partial digestion of sediments for the evaluation of trace element environmental pollution

Four different sample treatment methods for the determination of trace elements have been compared: a total digestion with HNO3-H2O2-HF using microwave, and three different standardized methods of fractionation: BCR three-steps sequential extraction, USEPA standard 3050B and ISO standard 11466. The four treatment methods were applied to the determination of Cu and Ni in four samples collected in different areas of Cienfuegos Bay (Cuba). The location of samples and the analytes were selected on the basis of results obtained by previous studies. Analyses following total digestion and BCR three-steps procedure were performed by inductively coupled plasma mass spectroscopy whereas analyses following EPA and ISO procedures were performed by flame atomic absorption spectroscopy. The results obtained have been compared with an estimated anthropic fraction evaluated in each sampling point as the difference between the total concentration and an estimated background concentration level. The BCR three-steps provided the best approximation of the estimated anthropic fraction and was therefore applied also in the determination of Pb and Cd for further consideration.     

Levels of PCBs, PCDDs and PCDFs in commercial butter samples in Spain

Feasibility of three different extraction methods for the simultaneous determination of polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in butter is discussed. The method based on liquid-liquid extraction with water of the non fatty solids from butter dissolved in hexane was found to be the most efficient for the determination of the lipid content and the levels of the investigated pollutants. This method was used to evaluate the background levels of PCBs, PCDDs and PCDFs in butters commercially available in Spain. Broad ranges of PCB, specifically, PCDD and PCDF concentrations were found in the different brands analysed. Levels, profiles and patterns of these pollutants in butter were compared with those previously reported for different Spanish dairy products. The toxic tetra-equivalents of 2,3,7,8-TCDD (1-TEQ) averages for PCDDs and PCDFs in the 21 butter samples analysed were 0.41 and 0.70 pg/g fat basis, respectively. These values were similar or lower than those cited in the literature for other countries.     

Method development for determination of fluroxypyr in water

Improved methods for extraction and clean up of fluroxypyr residue in water have been established. Two methods of fluroxypyr extraction were used, namely, Direct Measurement of fluroxypyr and Concentration of fluroxypyr onto A Solid Phase Extraction (SPE) Adsorbent, followed by elution with solvent before determination of fluroxypyr. The recovery for Direct Measurement of fluroxypyr in water containing 8-100 microg L(-1), ranged from 86 to 110% with relative standard deviation of 0.7 to 2.15%. For the second method, three types of SPE were used, viz. C18, C18 end-capped and polyvinyl dibenzene (ISOLUTE ENV+). The procedure involved concentrating the analyte from fluroxypyr-spiked water at pH 3, followed by elution of the analyte with 4 mL of acentonitrile. The recovery of fluroxypyr from the spiked sample at 1 to 50 microg L(-1) after eluting through either C18 or C18 end-capped ranged from 40-64% (with relative standard deviation of 0.7 to 2.15) and 41-65% (with standard deviation of 1.52 to 11.9). The use of ISOLUTE ENV+, gave better results than the C18, C18 end-capped or the Direct Measurement Methods. The recovery and standard deviation of fluroxypyr from spiked water using ISOLUTE ENV+ ranged from 91-102% and 2.5 to 5.3, respectively.     

Comparison of supercritical fluid extraction and Soxhlet extraction for the determination of PCBs in seaweed samples

The efficiency of supercritical fluid extraction for the determination of 12 polychlorinated biphenyls from algae samples is compared to Soxhlet extraction. Analytical detection limits for the individual congeners ranged from 0.62 microgl(-1) to 19 microgl(-1). Recovery was tested for both methods using standard addition procedure. At maximum spike level of concentration, the mean recoveries were not significantly different (P>0.05) of all PCBs studied, with the exception of PCBs 28, 52, 77 and 169. Method precision for Soxhlet extraction (< or =3.9%) was slightly better than for SFE (< or =9.2%). Although both methods yield comparable results, SFE offers the advantage of detecting all PCBs studied at lower concentrations, reducing extraction time, and reducing the amount of solvents needed. The optimized methods were applied to the analysis of three real seaweed samples, except for PCB101 the concentrations of all PCBs were low or below the detection limits. The levels of PCB101 found in sample 1 were 6.6+/-0.54 ng g(-1) d.w., in sample 2 the levels were 8.2+/-0.86 ng g(-1) d.w. and in sample 3 they were 7.7+/-0.08 ng g(-1) d.w.     

A rapid and efficient determination of natural estrogens in soils by pressurised liquid extraction and gas chromatography-mass spectrometry

We present a new analytical procedure for the extraction and determination of natural estrogens in soils based on pressurised liquid extraction and GC-MS determination. After testing twelve solvents, acetone proved to be the most efficient extractant. The optimum extraction temperature is 60 degrees C. Soil extracts have to be purified and concentrated by C-18 solid phase extraction. The dried extracts are derivatised by N-methyl-N-(trimethylsilyl)trifluoro-acetamide before measurement by GC-MS. Recoveries of 79-103% with relative standard deviations 相似文献   

Extraction and clean-up methods for organochlorine pesticides determination in milk

Organochlorine pesticides (OCPs) can cause environmental damage and human health risks since they are lipophilic compounds with high resistance to degradation and long half-lives in humans. As most persistent OCPs have been banned years ago, it is expected to find these compounds at trace levels in environment. Therefore, increasingly sensitive and reliable analytical techniques are required to ensure effective monitoring of these compounds. The aim of this review is to discuss extraction and clean-up methods used to monitor OCP residues in milk, reported in the last 20 years. To carry out this review, an exhaustive bibliographic review was conducted. Despite the disadvantages of conventional extraction and clean-up methods, such as liquid–liquid, solid-phase or Soxhlet extractions, these procedures are still used due to their reliability. New extraction methods, like solid-phase microextraction, matrix solid-phase dispersion or QuEChERS, have not been thoroughly evaluated for OCP determination in milk. Almost all the methodologies analyzed in this review presented good performance characteristics according to the performance acceptability criteria set in SANCO’s procedure. Comparison between limits of quantification (LOQ) and detection (LOD), for the reported methodologies, is not always possible due to the heterogeneity of the units. Thus, researchers should take into account an homogenization of LOD and LOQ units, according to the international regulations and MRLs established. Finally, more research is necessary to obtain the ideal methodology for OCPs determination in milk, which comprises the environmentally friendly characteristics of the new techniques and the reliability of the traditional methodologies.