密相流态化气力输送技术的工业试验研究

对燃煤电厂密相流态化气力输送系统的不同工况进行1：1工业试验研究。在不影响粉煤灰正常输送的前提下，采集系统核心部件仓泵的压力曲线及数据，对其进行分析。研究认为，仓泵的设计压力至少可以降低为0.8MPa，并对管路系统提出改进方案，为密相流态化气力输送的设计和运行提供参考依据。     

密相塔烟气脱硫技术试验研究

建立了密相塔烟气脱硫试验装置,并对烧结烟气进行了脱硫试验研究,验证了该工艺的可行性,并研究了主要因素对脱硫效率的影响.结果表明,钙硫比和近绝热饱和温度(approach to adiabatic saturation temperature,AAST)是影响脱硫效率的显著因素,循环灰浓度是保证系统脱硫效率的关键因素.在Ca/S比为1.2、密相塔出口烟气AAST=15℃、循环灰浓度为400g/m3条件下,系统能连续稳定运行,脱硫效率达92.5%以上,系统出口烟气中SO2浓度在150 mg/Nm3以下.     

密相塔烟气脱硫技术试验研究

建立了密相塔烟气脱硫试验装置,并对烧结烟气进行了脱硫试验研究,验证了该工艺的可行性,并研究了主要因素对脱硫效率的影响.结果表明,钙硫比和近绝热饱和温度（approach to adiabatic saturation temperature,AAST）是影响脱硫效率的显著因素,循环灰浓度是保证系统脱硫效率的关键因素.在Ca/S比为1.2、密相塔出口烟气AAST=15℃、循环灰浓度为400g/m3条件下,系统能连续稳定运行,脱硫效率达92.5%以上,系统出口烟气中SO2浓度在150 mg/Nm3以下.     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9％ ～5.4％.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3％的系统脱硫效率整体高于含湿量为5％和4％的样品,最大值达93.56％.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3％的循环脱硫灰较含湿量为5％的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5％样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaS03干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

两室堆肥生物反应装置研究

以堆肥过程中物料平衡、热量平衡以及垃圾生物发酵特性为依据,设计了二室堆肥生物反应装置,并通过堆肥试验实际检验反应装置设计的合理性.装置主要结构包括:二室堆肥发酵仓、保温层、通风供氧系统、空气加热系统以及二次污染控制系统.装置的主要特点为:两发酵仓能够独立完成堆肥发酵,也可以实现堆肥一次、二次发酵串联工艺组合;通过二次污染控制系统,可以很好地减少堆肥过程中产生的废水臭气排放;采用空气加热系统,可以快速均匀地加热堆体,以满足不同堆肥工艺的需要.装置在试验研究以及小规模垃圾堆肥处理领域有一定的应用价值.     

水泥窑烟气SNCR脱硝技术喷射系统的关键问题

喷射系统是水泥窑烟气SNCR脱硝技术的重要组成部分,对日产5 kt新型干法水泥烟气SNCR脱硝项目中的喷射系统进行了设计和实验研究.结果表明,系统压力设计、分配调节设计、喷枪布置和喷枪雾化能力是影响烟气脱硝效率的关键因素.在氨水质量分数为13.5％,喷入点温度904℃,n(NH3) /n(NH3)为1.2条件下,系统压力能够稳定运行在0.3～0.6 MPa之间、喷枪雾化颗粒度平均直径在50μm左右、喷枪在分解炉上的垂直安装角度为75°时烟气NOx浓度由原来的720 mg/Nm3降低到206 mg/Nm3,脱硝效率能达到70％,远低于水泥工业大气污染物排放标准的限定要求.对同类新型干法水泥熟料生产线SNCR脱硝技术有一定的参考意义.     

鼓泡床锅炉富氧焚烧含油污泥技术

提出了一种新型的含油污泥焚烧近零排放处理方式,即利用富氧燃烧技术焚烧含油污泥,油泥无需干化,并可以回收烟气中的CO_2直接用于油田驱油,可以实现CO_2的近零排放。以日焚烧200 t含油污泥为研究对象,构建了鼓泡床富氧燃烧含油污泥锅炉原则性热力系统,并分别从炉膛内密相区埋管、稀相区受热面和尾部对流受热面等方面进行了概念设计,根据鼓泡床锅炉的设计原则并结合富氧燃烧技术特点,设计了一台富氧燃烧含油污泥鼓泡床锅炉。详细介绍了鼓泡床焚烧锅炉的设计参数、结构布置,结果表明:鼓泡床富氧焚烧含油污泥系统的锅炉效率可达92.59%,富氧燃烧工况下炉膛内的换热量远远大于对流换热量。     

放射通道碟管式反渗透(RCDTRO)系统处理垃圾渗滤液

研究了碟管式反渗透(RCDTRO)系统处理垃圾渗滤液的性能,通过测定处理效果和对膜污染的抵抗力,对RCDTRO的性能进行了评估。研究表明:在不进行预处理和后置处理的情况下,一级RCDTRO系统对COD的去除率为(98.89±0.26)%、氨氮(NH+4-N)的去除率为(96.04±0.21)%、脱盐率为(97.53±0.18)%;良好的出水质量和对膜污染的强抵抗力(更长的清洗周期)进一步说明了RCDTRO系统处理渗滤液的技术可行性和经济适用性。其次,实验得出最佳的操作条件范围:压力为4.2~5.0 MPa,加压泵的频率为35 Hz,回收率为65%~75%。结果表明RCDTRO系统处理渗滤液在技术上和经济上都是可行的,并且能够在相对较低的压力下维持较高的处理效率。     

伞罩型除尘脱硫塔内除雾器性能研究

除雾器是湿法烟气脱硫(WFGD)系统内重要的设备之一,其性能对WFGD系统运行的可靠性有重要影响.利用Fluent6.2软件对新型伞罩型除尘脱硫塔内的三维两相流场进行数值模拟,气相采用RNG湍流模型,液相采用离散相模型,选择SIMPLE算法进行计算,分析塔内的折板除雾器和旋流板除雾器的速度场、压力场和液滴的分布情况.结果表明,烟气经过折板除雾器,产生了明显的压降,且在拐角区域湍流耗散强烈,是实现气液分离的关键区域;烟气经过旋流板除雾器,速度和压强分布具有良好的对称性,液滴被气流旋转抛向壁面实现气液分离.模拟结果对新型的WFGD除雾器的设计和运行具有一定的理论指导意义.     

在线固相萃取液质联用法测定饮用水源中的痕量联苯胺

建立了在线固相萃取液相色谱串联质谱法测定水中痕量联苯胺的方法。样品经自动进样器注入在线固相萃取小柱后,用富集泵流动相实现对样品的富集洗脱,然后用分析泵流动相将样品从富集柱冲洗至色谱柱后用串联质谱仪进行检测。该方法可在11 min内自动完成对样品的富集、净化、进样和检测过程。当进样量为5 m L时,联苯胺在0.010~2.0μg·L~(-1)范围内具有良好的线性关系,相关系数R为0.999,检出限为0.8 ng·L~(-1),实际水样的回收率为85%~104%。该方法具有简单、快速、重现性好、灵敏高等特点,可用于环境水体中痕量联苯胺的检测。     

Control of Coke Oven Emissions by Use of A Closed Pipeline Charging System

The body of information presented in this paper is directed to those individuals concerned with the control of air pollution emissions which occur as a result of the operation of by-product coke plants. It describes a new process which represents a major change in the charging operation wherein preheated coal can be charged to coke ovens via a closed pipeline system thus replacing the conventional larry charging car and thereby eliminating air pollution estimated to be as much as 70% of the total emissions from coke oven operations. Coal is dried and preheated in a continuous fluidized bed process utilizing products of combustion of coke oven gas. The coal is recovered in conventional cyclone collectors and conveyed to the ovens via a new and novel pneumatic conveying system where the gas used is superheated steam. Jet energy repeatedly thrusts the coal upward and forward through the pipe, obtaining a high efficiency of transport of solids ten times that of conventional systems. Major advantages of the process demonstrated to date include (1) elimination of emissions from charging, (2) reduction of emission from pushing, (3) improved battery top working conditions, (4) increased oven productivity as much as 45%.     

Photocatalytic oxidation of methyl orange in a three-phase fluidized bed reactor

The photocatalytic oxidation of methyl orange under weak illumination conditions was carried out in two different types of fluidized bed reactors. TiO2 powder was employed as the photocatalysts and a 15 W low pressure mercury lamp was used as the light source and the reactor volume was 2.5 l. The parametric study of photocatalytic oxidation of methyl orange in two different types of fluidized beds was investigated; effect of catalyst loadings, pH, air flow rate, initial concentration and oxygen concentration on the oxidation reaction rate. The experimental results were analyzed in conjunction with the characteristics of fluidized bed and the reactor geometry effect on the reaction rate was analyzed.     

Experimental investigation of pneumatic soil vapor extraction

Soil Vapor Extraction (SVE) is a common remediation technique for removing volatile organic compounds from unsaturated contaminated soils. Soil heterogeneities can however cause serious limitations to the applicability of SVE due to air bypassing low permeable areas of the soil, leading to diffusion limitation of the remediation. To enhance removal from areas subject to diffusion limitation a new remediation technique, pneumatic soil vapor extraction, is proposed. In contrast to traditional SVE, in which soil vapor is extracted continuously by a vacuum pump, pneumatic SVE is based on enforcing a sequence of large pressure drops on the system to enhance the recovery from the low-permeable areas. The pneumatic SVE technique was investigated in the laboratory using TCE as a model contaminant. 2D-laboratory tank experiments were performed on homogeneous and heterogeneous sand packs. The heterogeneous packs consisted of a fine sand lens surrounded by a coarser sand matrix. As expected when using traditional SVE, the removal of TCE from the low permeable lens was extremely slow and subject to diffusion limitation. In contrast when pneumatic venting was used removal rates increased by up to 77%. The enhanced removal was hypothesized to be attributed to mixing of the contaminated air inside the lens and generation of net advective transport out of the lens due to air expansion.     

Model analysis of mechanisms controlling pneumatic soil vapor extraction

The efficiency of traditional soil venting or soil vapor extraction (SVE) highly depends on the architecture of the subsurface because imposed advective air flow tends to bypass low-permeable contaminated areas. Pneumatic SVE is a technique developed to enhance remediation efficiency of heterogeneous soils by enforcing large fluctuating pressure fronts through the contaminated area. Laboratory experiments have suggested that pneumatic SVE considerably improves the recovery rate from low-permeable units. We have analyzed the experimental results using a numerical code and quantified the physical processes controlling the functioning of the method. A sensitivity analysis for selected boundary conditions, initial conditions and parameters was carried out to examine how the method behaves under conditions different from the experimental set-up. The simulations show that at the laboratory level the pneumatic venting technology is superior to the traditional technique, and that the method is particularly efficient in cases where large permeability contrasts exist between soil units in the subsurface.     

在线超声对流化床膜生物反应器污泥混合液性能影响的研究

在流化床膜生物反应器中引入在线超声辐射来控制膜污染,超声功率为300 W、频率分别为中频(50 kHz)和中低频(50 kHz和25 kHz)混合频率,考察了在线超声对反应器内混合液性能的影响及对膜污染的控制效果。结果表明,中频超声辐射不会对反应器内混合液的污泥浓度和粘度产生显著影响,而中低频超声辐射会降低混合液的污泥浓度并造成混合液粘度的升高。2种频率的超声辐射对污泥混合液的过滤性能和污泥活性都有一定的改善作用。连续运行26 d和29d后,在中频和中低频超声辐射的作用下,超声流化床膜生物反应器比普通流化床膜生物反应器的跨膜压差分别低8 kPa和14 kPa,说明2种频率的在线超声均可显著延缓膜污染。     

焦炉装煤烟尘治理方案的探讨

焦炉装煤烟尘含有害物质,污染环境,危害人体健康。袋式除尘器的使用,消除了烟尘的污染,但因投资大、运行费用高、操作复杂,难以得到快速、广泛的推广。根据实验结果和已有应用情况,本文推荐了三相流化床除尘装置和颗粒层除尘器,它们可用于焦炉装煤烟尘治理,其投资和运行费用会大大降低。     

焦炉装煤烟尘治理方案的探讨

焦炉装煤烟尘含有害物质，污染环境，危害人体健康。袋式除尘器的使用，消除了烟尘的污染，但因投资大、运行费用高、操作复杂，难以得到快速、广泛的推广。根据实验结果和已有应用情况，本文推荐了三相流化床除尘装置和颗粒层除尘器，它们可用于焦炉装煤烟尘治理，其投资和运行费用会大大降低。     

流化填料净化塔水力阻力研究

流化填料净化塔的阻力降计算 ,目前还没有精确的理论公式。本文利用废气治理工程中测试的数据 ,建立了流化填料净化塔的水力阻力经验式。在工程设计中 ,当条件相近时 ,直接用该公式设计是可行的。     

基于膨胀特性的厌氧流化床反应器的设计和运行控制

生物流化床的床层膨胀行为直接与生化反应区的水动力学和效率相关 ,床层膨胀特性是进行合理设计和运行的重要依据。目前流化床设计一般没有考虑生物膜的影响 ,但生物颗粒的流化行为有别于光滑载体 ,因此需要对曳力系数Cd 和膨胀特性方程中的ui 进行必要的修正。在综合分析基础上 ,探讨了优化两相流化床设计和运行的程序和方法