Deposition and leaching of tebuthiuron on sugar cane straw applied with and without alkyl polyglycoside adjuvant

A laboratory experiment was carried out aiming to study the effects of an alkyl polyglycoside adjuvant (APG) on deposition and leaching of the herbicide tebuthiuron applied on sugar cane straw. Tebuthiuron, at concentration of 1200 mg L(-1), was applied separately and in tank mix with the APG adjuvant, at concentrations of 0.07 and 0.09% (wt v(-1)), using a spraying volume of 204 L ha(-1). A precipitation equivalent to 20 mm of rain was simulated, 24 h after the applications, to evaluate the herbicide leaching. The quantification of tebuthiuron was carried out by the high performance liquid chromatography (HPLC). It was observed that the addition of APG adjuvant at 0.07% (wt v(-1)) provided an increase of 11.5% in the deposition of tebuthiuron on straw, reduction of 50.4% in the drift of the herbicide and it did not affect significantly the leached amount (68.5%), when compared with the treatment where tebuthiuron was applied alone (70.8%). At the concentration of 0.09% (wt v(-1)), the APG adjuvant caused an increase of 22.7% in the deposition; it reduced the drift of the herbicide by 99.9% and reduced the leached amount by 7.6% thereby increasing the retention of the herbicide by straw.     

Aminocyclopyrachlor sorption-desorption and leaching from three Brazilian soils

This study aimed to evaluate the sorption-desorption and leaching of aminocyclopyrachlor from three Brazilian soils. The sorption-desorption of ¹⁴C-aminocyclopyrachlor was evaluated using the batch method and leaching was assessed in glass columns. The Freundlich model showed an adequate fit for the sorption-desorption of aminocyclopyrachlor. The Freundlich sorption coefficient [K_{f (sorption)}] ranged from 0.37 to 1.34 µmol ^(1–1/n) L^1/n kg^?1 and showed a significant positive correlation with the clay content of the soil, while the K_{f (desorption)} ranged from 3.62 to 5.36 µmol ^(1–1/n) L^1/n kg^?1. The K_{f (desorption)} values were higher than their respective K_{f (sorption)}, indicating that aminocyclopyrachlor sorption is reversible, and the fate of this herbicide in the environment can be affected by leaching. Aminocyclopyrachlor was detected at all depths (0?30 cm) in all the studied soils, where leaching was influenced by soil texture. The total herbicide leaching from the sandy clay and clay soils was <0.06%, whereas, ～3% leached from the loamy sand soil. The results suggest that aminocyclopyrachlor has a high potential of leaching, based on its low sorption and high desorption capacities. Therefore, this herbicide can easily contaminate underground water resources.     

Leaching of S-metolachlor,terbuthylazine, desethyl-terbuthylazine,mesotrione, flufenacet,isoxaflutole, and diketonitrile in field lysimeters as affected by the time elapsed between spraying and first leaching event

The effect of elapsed time between spraying and first leaching event on the leaching behavior of five herbicides (terbuthylazine, S-metolachlor, mesotrione, flufenacet, and isoxaflutole) and two metabolites (desethyl-terbuthylazine and diketonitrile) was evaluated in a 2011–2012 study in northwest Italy. A battery of 12 lysimeters (8.4 m² long with a depth of 1.8 m) were used in the study, each filled with silty-loam soil and treated during pre-emergence with the selected herbicides by applying a mixture of commercial products Lumax (4 L ha^?1) and Merlin Gold (1 L ha^?1). During treatment periods, no gravity water was present in lysimeters. Irrigation events capable of producing leaching (40 mm) were conducted on independent groups of three lysimeters on 1 day after treatment (1 DAT), 7 DAT, 14 DAT, and 28 DAT. The series was then repeated 14 days later. Leachate samples were collected a few days after irrigation; compounds were extracted by solid phase extraction and analyzed by high-performance liquid chromatography and gas chromatography–mass spectrometry. Under study conditions, terbuthylazine and S-metolachlor showed the highest leaching potentials. Specifically, S-metolachlor concentrations were always found above 0.25 µg L^?1. Desethyl-terbuthylazine was often detected in leached waters, in most cases at concentrations above 0.1 µg L^?1. Flufenacet leached only when irrigation occurred close to the time of herbicide spraying. Isoxaflutole and mesotrione were not measured (<0.1 µg L^?1), while diketonitrile was detected in concentrations above 0.1 µg L^?1 on 1 DAT in 2011 only.     

Atrazine leaching through surface and subsurface of a tropical Oxisol

The fate of ¹⁴C atrazine was investigated using microcosms and an undisturbed Red-Yellow Latossol (Oxisol) under simulated rainfall conditions of 200 mm water month^?1. Experiments were carried out using microcosm cores, the first with an uncovered surface soil; the second set with uncovered subsurface soil; the third with subsurface soil covered with 3 cm of cow manure and the last with subsurface soil covered with 5 cm of grass straw. Average values for the amount of atrazine leached after 60 days were as follows: surface soil 1.6%; subsurface 47.3%; subsurface plus manure 17.3% and subsurface plus straw 24.8%. In the surface soil, 53% of the ¹⁴C atrazine remained within the upper 1 cm, while in the subsurface microcosms the atrazine was more evenly distributed. The authors report that surface soil was retained atrazine and its metabolites for 60 days. The addition of a straw or manure covering to exposed subsoil helped to retard atrazine leaching.     

Sorption, degradation, and leaching of tebuthiuron and diuron in soil columns

A study in small outdoor lysimeters was carried out to determine the leaching of the herbicides tebuthiuron and diuron in different soil types, using undisturbed soil columns. Soil sorption and degradation for both herbicides were also studied in the laboratory. The multi-layered AF (Attenuation Factor) model was evaluated for predicting the herbicides leaching in undisturbed soil columns. Tebuthiuron leached in greater amounts than diuron in both soils. Sorption was well represented by linear and Freundlich equations, however parameters from the linear equations were used in the AF model. In general, both herbicides presented very low sorption, with diuron presenting lower values of sorption coefficient than tebuthiuron in the two soils. Chromatographic data indicated rapid late degradation of diuron and tebuthiuron in both soil types at two different depths. Simple exponential equation was not able to represent degradation, thus a bi-exponential equation was used, and some model adjusting was needed. Average measured amounts of each herbicide were compared with amounts predicted by the multi-layered-soil AF model. The AF model was able to predict leaching amounts in the sandy soil, especially for diuron, however it did not perform well in the clayey soil.     

Effects of soil attributes and straw accumulation on the sorption of hexazinone and tebuthiuron in tropical soils cultivated with sugarcane

Brazil is the largest sugarcane producer in the world in which hexazinone (3-cyclohexyl-6-dimethylamino-1-methyl-1,3,5-triazine-2,4-dione) and tebuthiuron (1-(5-tert-butyl-1,3,4-thiadiazol-2-yl)-1,3-dimethylurea) are heavily used. Sugarcane harvesting is changing from the manual system with previous straw burning to the mechanized system without straw burning. The lack of burning results in soil organic carbon accumulation mainly in clayey soils, which should affect herbicides availability and fate. Therefore, we evaluated sorption of these herbicides in soil samples with and without straw burning. Both herbicides presented low apparent sorption coefficients (mean K_d,app= 0.6 and 2.4 L kg^?1 for hexazinone and tebuthiuron, respectively), suggesting that they may leach to groundwater. Moreover, their sorption correlated primarily with soil organic carbon (SOC), but iron oxide contents extracted with ammonium oxalate (Fe₂O₃^AOX) also affected it (K_d,app = ?0.228 + 0.0397 SOC + 0.117 Fe₂O₃^AOX for hexazinone and K_d,app = ?1.407 + 0.201 SOC + 0.348 Fe₂O₃^AOX for tebuthiuron). Soil organic carbon accumulation due to straw maintenance in the field positively affected sorption of both herbicides, but its effects were not enough to classify them as “non-leachers.”     

The combined effects of urea application and simulated acid rain on soil acidification and microbial community structure

Our aim was to test the effects of simulated acid rain (SAR) at different pHs, when applied to fertilized and unfertilized soils, on the leaching of soil cations (K, Ca, Mg, Na) and Al. Their effects on soil pH, exchangeable H⁺ and Al³⁺ and microbial community structure were also determined. A Paleudalfs soil was incubated for 30 days, with and without an initial application of urea (200 mg N kg^?1soil) as nitrogen (N) fertilizer. The soil was held in columns and leached with SAR at three pH levels. Six treatments were tested: SAR of pH 2.5, 4.0 and 5.6 leaching on unfertilized soil (T1, T2 and T3), and on soils fertilized with urea (T4, T5 and T6). Increasing acid inputs proportionally increased cation leaching in both unfertilized and fertilized soils. Urea application increased the initial Ca and Mg leaching, but had no effect on the total concentrations of Ca, Mg and K leached. There was no significant difference for the amount of Na leached between the different treatments. The SAR pH and urea application had significant effects on soil pH, exchangeable H⁺ and Al³⁺. Urea application, SAR treated with various pH, and the interactions between them all had significant impacts on total phospholipid fatty acids (PLFAs). The highest concentration of total PLFAs occurred in fertilized soils with SAR pH5.6 and the lowest in soils leached with the lowest SAR pH. Soils pretreated with urea then leached with SARs of pH 4.0 and 5.6 had larger total PLFA concentrations than soil without urea. Bacterial, fungal, actinomycete, Gram-negative and Gram-positive bacterial PLFAs had generally similar trends to total PLFAs.     

Sorption of Isoxaflutole Diketonitrile Degradate (DKN) and Dicamba in Unsaturated Soil

When analyzing the sorption characteristics of weakly sorbing or labile pesticides, batch methods tend to yield a high margin of error attributable to errors in concentration measurement and to degradation, respectively. This study employs a recently developed unsaturated transient flow method to determine the sorption of isoxaflutole's herbicidally active diketonitrile degradate (DKN) and dicamba. A 20-cm acrylic column was packed with soils with varied texture that had been uniformly treated with ¹⁴C-labeled chemical.

The antecedent solution herbicide in equilibrium with sorbed phase herbicide was displaced by herbicide-free water, which was infiltrated into the column. Sorption coefficients, K_d, were obtained from a plot of total herbicide concentration in the soil versus water content in the region where the antecedent solution accumulated. DKN K_d values were ～2–3 times (average K_d = 0.71 L kg^?1) greater using the unsaturated transient flow method as compared to the batch equilibration method in clay loam (K_d = 0.33 L kg^?1), but similar for the two methods in sand (0.12 vs 0.09 L kg^?1) soils. Dicamba K_d values were 3 times greater using the unsaturated transient flow method as compared to the batch equilibration method in the clay loam soil (0.38 vs 0.13 L kg^?1), however, the K_d values were the same for the two methods in the sand (～0.06 L kg^?1). This demonstrates that to determine sorption coefficients for labile hydrophilic pesticides, an unsaturated transient flow method may be a suitable alternative to the batch method. In fact, it may be better in cases where transport models have overpredicted herbicide leaching when batch sorption coefficients have been used.     

Remediation of DDT-Contaminated Water and Soil by Using Pretreated Iron Byproducts from the Automotive Industry

The objective of this study was to quantify the effectiveness of different pretreated iron byproducts from the automotive industry to degrade DDT [(1,1,1-trichloro-2,2-bis(4-chlorophenyl) ethane] in aqueous solutions and soil slurry. Iron byproducts from automotive manufacturing were pretreated by three different methods (heating, solvent and 0.5N HCl acid washing) prior to experimentation. All pretreated irons were used at 5% (wt v^{? 1}) to treat 0.014 mM (5 mgL^{? 1}) of DDT in aqueous solution. Among the pretreated irons, acid pretreated iron results in the fastest destruction rates, with a pseudo first-order degradation rate of 0.364 d^{? 1}. By lowering the pH of the DDT aqueous solution from 9 to 3, destruction kinetic rates increase more than 20%. In addition, when DDT-contaminated soil slurry (3.54 mg kg^{? 1}) was incubated with 5% (wt v^{? 1}) acid-pretreated iron, more than 90% destruction of DDT was observed within 8 weeks. Moreover, DDT destruction kinetics were enhanced when Fe(II), Fe(III) or Al(III) sulfate salts were added to the soil slurry, with the following order of destruction kinetics: Al(III) sulfate > Fe(III) sulfate > Fe(II) sulfate. These results provide proof-of concept that inexpensive iron byproducts of the automotive industry can be used to remediate DDT-contaminated water and soil.     

Leaching and half-life of the herbicide tebuthiuron on a recharge area of Guarany aquifer in sugarcane fields in Brazil

This study was undertaken to evaluate the degradation and mobility of the herbicide tebuthiuron (N-[5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl]-N,N′-dimethylurea) in soil under field conditions, and its potential for leaching and groundwater contamination. A watershed, Espraiado, located over a recharge area in Brazil, was chosen for soil and water studies. At Espraiado, water samples were collected from seven wells at intervals of three months from March 2004 to June 2006 and analyzed for tebuthiuron. Other samples were taken from city wells located outside of the recharge area. To assess the potential movement to the aquifer, tebuthiuron was also applied to trial plots at the recommended label rate of 1.0 kg/ha a.i. in May of 2004, with and without sugarcane coverage, on sandy soil. Soil samples were collected during the years of 2004 and 2005, at depths intervals of 20 cm from soil surface down to 120 cm and analyzed for tebuthiuron at zero, 3, 30, 60, 90, 120, 150, 180, 240, and 300 days after application. There was no clear effect of sugarcane coverage on the tebuthiuron degradation in soils, but it moved faster into the soil where there was no cover. After 180 days there were no measurable residues in the soil, and tebuthiuron was not found below 40 cm depth in any time. Tebuthiuron had a half-life of 20 days under those conditions. No tebuthiuron residue was found in ground water samples at any sampling time.     

Persistence of herbicide fenoxaprop ethyl and its acid metabolite in soil and wheat crop under Indian tropical conditions

The persistence of fenoxaprop ethyl {Ethyl (RS)-2-[4-(6-chloro-1,3-benzoxazol-2-yloxy) phenoxy] propionate} herbicide and its active metabolite fenoxaprop acid was investigated in soil and wheat crop. Fenoxaprop acid was prepared by alkaline hydrolysis of fenoxaprop ethyl. A HPLC method was developed in which fenoxaprop ethyl herbicide and its acid metabolite showed sharp single peak at 6.44 and 2.61 min respectively. The sensitivity of the method for ester and acid was 2 and 1 ng respectively with limit of detection of 0.1 and 0.05 μg mL^?1. The recovery of fenoxaprop ethyl and fenoxaprop acid from soil, wheat straw and grain ranged between 73.8–80.2%. In a field experiment fenoxaprop ethyl (Puma super® 10 EC) when applied to wheat crop at the rate of 120 g and 240 g a.i. ha^-1 as post emergence spray, fenoxaprop ethyl converted to fenoxaprop acid. Residues of fenoxaprop ethyl and acid dissipated in soil with a half-life of 0.5 and 7.3 days, respectively. At harvest no detectable residues of fenoxaprop ethyl or acid were observed in soil, wheat grain and straw samples.     

Adsorption of glyphosate on Brazilian subtropical soils rich in iron and aluminum oxides

Abstract

We investigated the adsorption of glyphosate onto five subtropical soils of Paraná and São Paulo states, Brazil, a region of intense agricultural activities, aiming at the determination of kinetic and isotherm adsorption parameters which enable the evaluation of the potential leaching of the herbicide. The adsorption was fast, being described by the pseudo-second order and intraparticle diffusion models, thus suggesting that mixed mechanisms are involved. The Oxisol containing the highest concentrations of metal oxides (209.5?g kg^?1 Fe₂O₃ and 160.2?g kg^?1 Al₂O₃) was the sample with the highest rate constant, indicating the adsorption sites are readily available. All the soils are rich in aluminum and iron oxides, explaining the Freundlich coefficients (K_F) between 642 and 1360?mg^1-1/n kg^?1 L^1/n, which are higher than most of the coefficients described for other soils around the world. The maximum desorption (15% of the adsorbed amount) was observed for the Oxisol. For the other soils, desorption ranged from 2 to 7%. These results suggest that the leaching of free glyphosate to nearby surface and groundwaters is unlikely unless excessive doses are used. The adsorption parameters are useful for managing the right doses applied to the crops, thus avoiding contamination of adjacent areas.     

Dissipation of pendimethalin in the soil of field pea (Pisum sativum L.) and detection of terminal residues in plants

Dissipation of pendimethalin in the soil of field peas (Pisum sativum L.) at 0 to 110 days, and terminal residues in green and mature pea were studied under field conditions. Pendimethalin was applied as pre-emergence herbicide at 750, to 185 g a.i. ha^?1 in winter, in field peas. Dissipation of pendimethalin in the soil at 0 to 110 days followed first-order kinetics showing a half-life of 19.83 days averaged over all doses. Low pendimethalin residues were found in mature pea grain (0.004, 0.003, <0.001 μg g^?1), and straw (0.007, 0.002, <0.001 μg g^?1) at 750, 350 and 185 g a.i. ha^?1 treatments, respectively. The study indicated that residues of pendimethalin in green and mature pea were within the prescribed MRL limits.     

Sorption and leaching of flucetosulfuron in soil

Abstract

The adsorption–desorption and leaching of flucetosulfuron, a sulfonylurea herbicide, was investigated in three Indian soils. Freundlich adsorption isotherm described the sorption mechanism of herbicide with adsorption coefficients (K_f) ranging from 17.13 to 27.99 and followed the order: Clayey loam?>?Loam?>?Sandy loam. The K_f showed positive correlation with organic carbon (OC) (r?=?0.910) and clay content (r?=?0.746); but, negative correlation with soil pH (r = ?0.635). The adsorption isotherms were S-type suggesting that herbicide adsorption was concentration dependent and increased with increase in concentration. Desorption followed the sequence: sandy loam?>?clayey loam?>?loam . Hysteresis (H) was observed in all the three soils with H?<?1. Leaching of flucetosulfuron correlated positively with the soil pH; but, negatively with the OC content. Sandy loam soil (OC- 0.40%, pH ?7.25) registered lowest adsorption and highest leaching of flucetosulfuron while lowest leaching was found in the loam soil (pH ? 7.89, OC ? 0.65%). The leaching losses of herbicide increased with increase in the rainfall intensity. This study suggested that the soil OC content, pH and clay content played important roles in deciding the adsorption–desorption and leaching behavior of flucetosulfuron in soils.     

Uptake,translocation, and control of trumpet flower (Tecoma stans) with aminocyclopyrachlor

To gain a better understanding of the physiology of the herbicide aminocyclopyrachlor in young plants of trumpet flower, the uptake and translocation were evaluated after the application of herbicide. This was determined by treating individual leaves with formulated herbicides plus ¹⁴C-aminocyclopyrachlor after the application of the formulated herbicide. This experiment used a randomized experimental design with three replications. In addition, field studies were conducted to assess the effectiveness of foliar applications of aminocyclopyrachlor in association with metsulfuton-methyl. The plant absorbed 20% of the herbicide applied. The translocation percentage did not surpass 5% of the total amount applied. Only 1% of the herbicide applied was translocated to the roots. Rate of 40 + 13 g a.i. 100 L^?1 of aminocyclopyrachlor+metsulfuron-methyl was effective to control T. stans.     

Natural deep eutectic solvent mediated pretreatment of rice straw: bioanalytical characterization of lignin extract and enzymatic hydrolysis of pretreated biomass residue

The present investigation demonstrated pretreatment of lignocellulosic biomass rice straw using natural deep eutectic solvents (NADESs), and separation of high-quality lignin and holocellulose in a single step. Qualitative analysis of the NADES extract showed that the extracted lignin was of high purity (>90 %), and quantitative analysis showed that nearly 60?±?5 % (w/w) of total lignin was separated from the lignocellulosic biomass. Addition of 5.0 % (v/v) water during pretreatment significantly enhanced the total lignin extraction, and nearly 22?±?3 % more lignin was released from the residual biomass into the NADES extract. X-ray diffraction studies of the untreated and pretreated rice straw biomass showed that the crystallinity index ratio was marginally decreased from 46.4 to 44.3 %, indicating subtle structural alterations in the crystalline and amorphous regions of the cellulosic fractions. Thermogravimetric analysis of the pretreated biomass residue revealed a slightly higher T _dcp (295 °C) compared to the T _dcp (285 °C) of untreated biomass. Among the tested NADES reagents, lactic acid/choline chloride at molar ratio of 5:1 extracted maximum lignin of 68?±?4 mg g^?1 from the rice straw biomass, and subsequent enzymatic hydrolysis of the residual holocellulose enriched biomass showed maximum reducing sugars of 333?±?11 mg g^?1 with a saccharification efficiency of 36.0?±?3.2 % in 24 h at 10 % solids loading.     

Mobility and efficacy of 2,4-D herbicide from slow-release delivery systems based on organo-zeolite and organo-bentonite complexes

This research aimed to develop slow-release formulations (SRFs) of 2,4-dichlorophenoxyacetic acid (2,4-D) using zeolite and bentonite minerals modified with cetyltrimethylammonium (CTMA) surfactant. Adsorption–desorption, greenhouse bioassay and column experiments were carried out to assess the potential of the SRFs to control weeds while reducing the herbicide leaching losses to deep layers of soil. The results showed that only 6.5 mmol 2,4-D kg^?1 was retained by Na-bent, and the herbicide was not adsorbed by Na-zeol at all. The surface modification with CTMA surfactant, however, improved the 2,4-D adsorption capacity of the zeolite and bentonite up to 207.5 and 415.8 mmol kg^?1, respectively. The synthesized organo-minerals slowly released the retained 2,4-D discharging 22 to 64% of the adsorbed 2,4-D to the solution phase within 7 days. The SRFs significantly (P = 0.05) reduced the herbicide mobility within the soil columns keeping a great portion of the herbicide active ingredient in the upper 5 cm soil layer. The SRFs were significantly (P = 0.05) as effective as the free technical herbicide in weed control without harming the ryegrass as the main plant. Therefore, the synthesized SRFs could be considered as useful tools for weed control in sustainable agriculture.     

Determination of pendimethalin (PROWL®480 EC) spray drift from ground applications

Abstract

Pendimethalin herbicide (PROWL^®480 EC) spray drift was determined from ground applications representing the highest rate applied to corn in eastern Canada. A novel drift collector pattern was laid out on the ground immediately before herbicide application. Most of the drift collectors were located downwind of the application target area. The maximum labelled rate of 1.68 kg ai/Ha was applied on 2 occasions on separate sites. In both applications, drift collector cards indicated that concentrations of pendimethalin were not detectable outside the target zone (<0.01 μg/cm²) at or beyond the 10 metre drift collector stations. Risk assessment calculations indicated that non‐target organisms would not be at significant risk from off‐site movement of pendimethalin.     

Matrine and oxymatrine in corroborant plant extracts and fertilizers: HPLC/MS-MS method development and single-laboratory validation

A reversed phase high-performance liquid chromatographic method (HPLC/MS-MS) has been developed and validated for detection of alkaloids matrine and oxymatrine in fertilizer with labeled enhancer plant defense activities. The analytical method was validated statistically. The results show a strong matrix effect, requiring quantification by standard addition method. The regression lines showed r² > 0.994. Recoveries ranging from 97 to 104% were obtained for the fortification level of 0.01% wt wt^?1 and the relative standard deviations ranged from 3 to 4% (n = 10). The limits of detection were below 0.0001% wt wt^?1, while the limits of quantification did not exceed 0.0004% wt wt^?1. The method is currently applied in ICQRF Laboratory of Catania on fertilized and corroborant plant extract collected in the Italian market in the frame of MIPAAF institutional quality control activity, with the aim to dectect these unpermitted active substances.     

Dissipation and runoff transport of metazachlor herbicide in rapeseed cultivated and uncultivated plots in field conditions

The environmental fate of metazachlor herbicide was investigated under field conditions in rapeseed cultivated and uncultivated plots, over a period of 225 days. The cultivation was carried out in silty clay soil plots with two surface slopes, 1 and 5 %. The herbicide was detectable in soil up to 170 days after application (DAA), while the dissipation rate was best described by first-order kinetics and its half-life ranged between 10.92 and 12.68 days. The herbicide was detected in the soil layer of 10–20 cm from 5 to 48 DAA, and its vertical movement can be described by the continuous stirred tank reactor (CSTR) in series model. Relatively low amounts of metazachlor (less than 0.31 % of the initial applied active ingredient) were transferred by runoff water. More than 80 % of the total losses were transferred at the first runoff event (12 DAA), with herbicide concentrations in runoff water ranging between 70.14 and 79.67 μg L⁻¹. Minor amounts of the herbicide (less than 0.07 % of the initial applied active ingredient) were transferred by the sediment, with a maximum concentration of 0.57 μg g⁻¹ (12 DAA), in plots with 5 % inclination. Finally, in rapeseed plants, metazachlor was detected only in the first sampling (28 DAA) at concentrations slightly higher than the limit of quantification; when in seeds, no residues of the herbicide were detected.