Fly-ash-amended sand as filter media in bioretention cells to improve phosphorus removal.

This study identified material with high phosphorus sorption suitable for bioretention filter media. Materials examined were fly ash, two expanded shales, peat moss, limestone, and two common Oklahoma soils--Teller loam and Dougherty sand. The peat moss was a phosphorus source, while the two soils, limestone, and one expanded shale had only modest sorption capacity. One expanded shale and the fly ash had significant phosphorus sorption. Fly ash is unsuitable for use in a pure form, as a result of its low permeability, but phosphorus sorption on the sand was increased significantly with the incorporation of small amounts of fly ash. Column leaching experiments found that the sand with 2.5 and 5% fly ash and the better expanded shale had linear, non-equilibrium transport retardation factors of 272, 1618, and 185, with first-order rate coefficients of 0.153, 0.0752, and 0.113 hour(-1), respectively. Desorption experiments showed that the phosphorus sorption on the sand/fly ash mixture is largely nonreversible. Transport simulation assuming a 1-m-deep sand/fly ash treatment layer, with 5% of the watershed area, showed that the sand/fly ash filter media could effectively treat 1 mg/L influent for 12 years in a paved watershed and 34 years in a grassed watershed before exceeding Oklahoma's scenic rivers' phosphorus criterion of 0.037 mg/L. Significant phosphorus removal would continue for over 100 years.     

Practical and mechanistic aspects of the removal of cadmium from aqueous systems using peat

A sphagnum peat moss removed Cd from aqueous solutions very efficiently, and its effectiveness in taking up the metal was significantly enhanced by exposure to a 1N NaOH solution. The capacity of the untreated peat for Cd reached 300 g/kg and that of the NaOH-activated peat was over 400 g/kg. Although saturation was rarely reached, the Cd uptake from concentrated solutions often exceeded 200 g/kg. In column experiments, 1g of the NaOH-activated peat completely removed the metal from over 0.2L of a 200-mg/L Cd solution (final Cd concentration<0.1mg/L), while 1g of non-activated peat cleared Cd from less than 25% of that volume. The cation exchange capacity measured for the peat depended on the time of contact with the exchanging solution. After 72 h contact, the value for the NaOH-activated peat was 135 cmol(c)/kg. In addition to uptake by exchange, a significant amount of Cd was sorbed by non-exchange mechanisms. FTIR spectroscopy revealed the importance of carboxyl groups in the uptake.     

Sorption of isoxaflutole diketonitrile degradate (DKN) and dicamba in unsaturated soil

When analyzing the sorption characteristics of weakly sorbing or labile pesticides, batch methods tend to yield a high margin of error attributable to errors in concentration measurement and to degradation, respectively. This study employs a recently developed unsaturated transient flow method to determine the sorption of isoxaflutole's herbicidally active diketonitrile degradate (DKN) and dicamba. A 20-cm acrylic column was packed with soils with varied texture that had been uniformly treated with 14C-labeled chemical.The antecedent solution herbicide in equilibrium with sorbed phase herbicide was displaced by herbicide-free water, which was infiltrated into the column. Sorption coefficients, Kd, were obtained from a plot of total herbicide concentration in the soil versus water content in the region where the antecedent solution accumulated. DKN Kd values were approximately 2-3 times (average Kd = 0.71 L kg-1) greater using the unsaturated transient flow method as compared to the batch equilibration method in clay loam (Kd = 0.33 L kg-1), but similar for the two methods in sand (0.12 vs 0.09 L kg-1) soils. Dicamba Kd values were 3 times greater using the unsaturated transient flow method as compared to the batch equilibration method in the clay loam soil (0.38 vs 0.13 L kg-1), however, the Kd values were the same for the two methods in the sand (approximately 0.06 L kg-1). This demonstrates that to determine sorption coefficients for labile hydrophilic pesticides, an unsaturated transient flow method may be a suitable alternative to the batch method. In fact, it may be better in cases where transport models have overpredicted herbicide leaching when batch sorption coefficients have been used.     

Sorption and mobility of metronidazole, olaquindox, oxytetracycline and tylosin in soil

Laboratory studies were conducted to characterise four different antibiotic compounds with regard to sorption and mobility in various soil types. Distribution coefficients (Kd values) determined by a batch equilibrium method varied between 0.5 and 0.7 for metronidazole, 0.7 and 1.7 for olaquindox and 8 and 128 for tylosin. Tylosin sorption seems to correlate positively with the soil clay content. No other significant interactions between soil characteristics and sorption were observed. Oxytetracycline was particularly strongly sorbed in all soils investigated, with Kd values between 417 in sand soil and 1026 in sandy loam, and no significant desorption was observed. Soil column leaching experiments indicated large differences in the mobility of the four antibiotic substances, corresponding to their respective sorption capabilities. For the weakly adsorbed substances metronidazole and olaquindox the total amounts added were recovered in the leachate of both sandy loam and sand soils. For the strongly adsorbed oxytetracyline and tylosin nothing was detected in the leachate of any of the soil types, indicating a much lower mobility. Results from defractionation and extraction of the columns (30 cm length) showed that 60-80% of the tylosin added had been leached to a depth of 5 cm in the sandy loam soil and 25 cm in the sand soil.     

The sorption of Zectran on bottom sediments and peat moss

Abstract

A modified analytical method employed to determine the insecticide Zectran in natural waters frequently has resulted in erroneous data. The errors have been attributed to interferences from particulate matter in these waters. In order to evaluate analytical interferences due to sorption of Zectran on particu‐lates, a series of experiments was performed using bottom sediments and a peat moss in contact with aqueous solutions of Zectran at a pH value of 6.0 and 20°C.

Isotherm studies confirmed that Zectran sorption occurs in a direct relation to the amount of chemically oxidizable carbon present in the bottom sediments or peat moss. However, the extent of sorption was limited, which suggested that particulates may not be the primary interference in the modified analytical method.     

Fertilizer source effects on phosphate and nitrate leaching through simulated golf greens

Phosphorus and nitrogen leached from high-porosity golf greens can adversely affect surface water and groundwater quality. Greenhouse and field lysimeter experiments were carried out to determine the effects of eight fertilizer sources on P and N leaching from simulated golf greens. Phosphorus appeared in the leachate later than nitrate-N, and the highest concentrations were for the soluble 20-20-20 and the 16-25-12 starter fertilizers. The other six sources resulted in lower P concentrations. The soluble 20-20-20 and the 16-25-12 sources each resulted in 43% of the added P eluting in the leachate, whereas the others varied from 15 to 25%. For nitrate-N the lowest cumulative mass was for the controlled-release 13-13-13 and sulfur-coated urea. A higher percentage of applied P than applied N leached from both field and greenhouse lysimeters. However, the amounts of P leached for the field lysimeters were lower than for the greenhouse columns.     

Tylosin sorption to silty clay loam soils, swine manure, and sand

The objectives of this study were to assess sorption and desorption of tylosin, a macrolide antimicrobial chemical used in swine, cattle, and poultry production, in three silty clay loam soils of South Dakota and compare soil sorption to sand and manure sorption. The silty clay loam soils, from a toposequence in eastern South Dakota, standardized sand samples, and swine manure were used in 24-h batch sorption studies with tylosin concentrations ranging from 25 to 232 micro mole/L. Desorption from soil was conducted over a four-day period. Partition coefficients, based on the Freundlich isotherm (K(f)) or K(d) values, were calculated. K(f) values for the silty clay loams were similar, not influenced by landscape position, and averaged 1,350 with isotherm slopes ranging from 0.85 to 0.93. K(f) values for sand were dependent on solution/sand ratios and pH, ranging from 1.4 to 25.1. K(d) values of manure were dependent on the solution type and ranged from 840 L/kg with urine to about 175 L/kg when sorbed from water. Desorption of tylosin from each soil over the four-day period was < 0.2% of the amount added. The soils' high K(f) values and low desorption amounts suggest that once tylosin is in these soils, leaching to lower depths may not occur. However, this does not preclude runoff with soil eroded particles. If tylosin reaches a sand aquifer, through bypass flow or other mechanism(s), movement in the aquifer most likely would occur.     

Sorption and desorption kinetics of diuron, fluometuron, prometryn and pyrithiobac sodium in soils

The sorption and desorption characteristics of four herbicides (diuron, fluometuron, prometryn and pyrithiobac-sodium) in three different cotton growing soils of Australia was investigated. Kinetics and equilibrium sorption and desorption isotherms were determined using the batch equilibrium technique. Sorption was rapid (> 80% in 2 h) and sorption equilibrium was achieved within a short period of time (ca 4 h) for all herbicides. Sorption isotherms of the four herbicides were described by Freundlich equation with an r2 value > 0.98. The herbicide sorption as measured by the distribution coefficient (Kd) values ranged from 3.24 to 5.71 L/kg for diuron, 0.44 to 1.13 L/kg for fluometuron, 1.78 to 6.04 L/kg for prometryn and 0.22 to 0.59 L/kg for pyrithiobac-sodium. Sorption of herbicides was higher in the Moree soil than in Narrabri and Wee Waa soils. When the Kd values were normalised to organic carbon content of the soils (Koc), it suggested that the affinity of the herbicides to the organic carbon increased in the order: pyrithiobac-sodium < fluometuron < prometryn < or = diuron. The desorption isotherms were also adequately described by the Freundlich equation. For desorption, all herbicides exhibited hysteresis and the hysteresis was stronger for highly sorbed herbicides (diuron and prometryn) than the weakly sorbed herbicides (fluometuron and pyrithiobac-sodium). Hysteresis was also quantified as the percentage of sorbed herbicides which is not released during the desorption step (omega = [nad/nde - 1] x 100). Soil type and initial concentration had significant effect on omega. The effect of sorption and desorption properties of these four herbicides on the off-site transport to contaminate surface and groundwater are also discussed in this paper.     

Sorption of fenamiphos to different soils: the influence of soil properties

Fenamiphos (0-ethyl-0(3-methyl-4-methylthiophenyl)-isopropylamido-phosphate) is a widely used nematicide and insecticide in bowling greens and agriculture, but information on its sorption including its metabolites is limited. Hence, the sorption of fenamiphos (nematicide) and its major degradation products fenamiphos sulfoxide (FSO) and fenamiphos sulfone (FSO2) were determined in thirteen contrasting soils collected from Australia and Ecuador. The sorption coefficients (Kd) exhibited a wide range of variation from 2.48 to 14.94 L/Kg for fenamiphos; from 0 to 7.42 L/Kg for FSO and from 0 to 9.49 L/Kg for FSO2. The sorption affinity of the three compounds for all soils tested was as follows: fenamiphos > fenamiphos sulfone > fenamiphos sulfoxide. The results showed that the sorption of fenamiphos and its metabolites in some soils is very low, and in one case is nonexistant for the metabolites. This is of particular concern as due to its low sorption coefficient, the compound could easily migrate and contaminate water bodies. Fenamiphos and its oxidation products have been reported to be highly toxic to aquatic invertebrates and therefore, the information generated in this study assumes great importance in the risk assessment of fenamiphos and its metabolites in the environment.     

Tylosin Sorption to Silty Clay Loam Soils,Swine Manure,and Sand

The objectives of this study were to assess sorption and desorption of tylosin, a macrolide antimicrobial chemical used in swine, cattle, and poultry production, in three silty clay loam soils of South Dakota and compare soil sorption to sand and manure sorption. The silty clay loam soils, from a toposequence in eastern South Dakota, standardized sand samples, and swine manure were used in 24-h batch sorption studies with tylosin concentrations ranging from 25 to 232 μ mole/L. Desorption from soil was conducted over a four-day period. Partition coefficients, based on the Freundlich isotherm (K _f ) or K _d values, were calculated. K _f values for the silty clay loams were similar, not influenced by landscape position, and averaged 1350 with isotherm slopes ranging from 0.85 to 0.93. K _f values for sand were dependent on solution/sand ratios and pH, ranging from 1.4 to 25.1. K _d values of manure were dependent on the solution type and ranged from 840 L/kg with urine to about 175 L/kg when sorbed from water. Desorption of tylosin from each soil over the four-day period was < 0.2% of the amount added. The soils' high K _f values and low desorption amounts suggest that once tylosin is in these soils, leaching to lower depths may not occur. However, this does not preclude runoff with soil eroded particles. If tylosin reaches a sand aquifer, through bypass flow or other mechanism(s), movement in the aquifer most likely would occur.     

Retention of organic and inorganic chemicals by the drainage/supply piping material

A critical issue facing the turfgrass industry is the environmental fate and transport of organic and inorganic chemicals used on golf courses. The fate and distribution of those chemicals are strongly influenced by sorptive interactions with soil and sediment. In this study, the drainage and water supply piping material (used for construction of a prototype encapsulated golf green) was utilized to determine its potential sorption of three organic chemicals [2,4-dichloro-phenoxyacetic acid] (2,4-D), naphthalene and toluene and nitrate. Crushed piping material (small-to-large particle sizes) was evaluated. Isotherms were constructed using a batch equilibration technique. The results showed that the drainage/supply piping material at small particle sizes (<2.5 mm) has higher sorptive ability compared to soil (1.7 for 2,4-D and 13.4 for naphthalene). The K(F) value was 44, 253 and 70 for 2,4-D, naphthalene and toluene, respectively. K(oc) values were much higher than those of peat and soil at lower equilibrium concentrations. However, sorption decreased dramatically with increasing particle size (approaching zero at particle size 10 mm), due to reduction of surface areas and sorption sites. Sorption of NO(3)-N by the piping material was negligible. We concluded that sorption by intact drainage/supply piping material would not affect the recycling efficiency of pesticides and nutrients in the constructed encapsulated green. Conversely, drainage/supply piping material particles smaller than 2.5 mm in diameter can effectively be utilized as a filtering material.     

Adsorption-desorption,persistence, and leaching behavior of dithiopyr in an alluvial soil of India

Investigations were undertaken to determine the adsorption-desorption, persistence and leaching of dithiopyr (S,S'-dimethyl 2-difluoromethyl-4-isobutyl-6-trifluoromethyl pyridine-3,5-dicarbothioate) in an alluvial soil under laboratory condition. The adsorption-desorption studies were carried out using batch equilibration technique. The mass balance studies showed that 83-97% of the pesticide was recovered during adsorption-desorption studies. The results revealed strong adsorption of dithiopyr in alluvial soil with Kd values ranging from 3.97-5.78 and Freundlich capacity factor (KF) value of 2.41. The strong adsorption was evident from the hysteresis effect observed during desorption. The hysteresis coefficients ranged from 0.17-0.40. The persistence studies were carried out at two concentrations (1.0 and 10.0 microg g(-1) level) under field capacity moisture and submerged condition by incubating the treated soil at 25 +/- 1 degrees C. In general, dithiopyr persisted beyond 90 days with half-life varying from 11.5-12.9 days under different conditions. The rate of application and moisture regimes had no overall effect on the persistence. The leaching studies carried out in packed column under saturated flow condition revealed that dithiopyr was highly immobile in alluvial soil. Only small amounts (0.02-0.04%) were recovered from leachate whereas major portion (99.9%) remained in top layer of the soil column. The data suggest that strong adsorption of dithiopyr will cause a greater persistence problem in the soil. However, the chances of its movement to ground water will be negligible due to its immobility.     

Distribution coefficient of selenium in Japanese agricultural soils

In order to evaluate the selenium (Se) sorption level in Japanese soils, soil/soil solution distribution coefficients (K(d)s) were obtained for 58 agricultural soil samples (seven soil classification groups) using 75Se as a tracer. Although several chemical forms of Se are present in agricultural fields, selenite was used, because it is the major inorganic Se form in acid soils such as found in Japan. The Kd values obtained covered a wide range, from 12 to 1060l/kg, and their arithmetic mean was 315l/kg. Among the soil groups, Andosols had higher Kd values. The Kd values for all samples were highly correlated with soil active-aluminum (Al) and active-iron (Fe) contents. Thus, active-Al and active-Fe were considered to be the major adsorbents of Se. Then, a new sequential extraction procedure was applied to 12 soil samples in order to quantify the effect of soil components on Se adsorption. The sequential extraction results showed that 80-100% of the adsorbed Se was recovered as Al-bound Se and Fe-bound Se. The amount of Al-bound Se was the highest in the soils that showed high Kd values, though the relative contribution of Fe-bound Se tended to increase with decreasing Kd values. The high values of Kd seemed to be caused mainly by the adsorption of Se onto active-Al in Japanese soils.     

Sorption of fipronil and its metabolites on soils from South Australia

This paper reports on the sorption of fipronil [(+/-)-5-amino-1-(2,6-dichloro-alpha,alpha,alpha-trifluoro-p-tolyl)-4-trifluoromethyl-sulfinylpyrazole-3-carbonitrile] and its two main metabolites, desulfynil and sulfide derivatives on a range of soils from South Australia. The Freundlich sorption coefficient (Kf) values for fipronil on the soils ranged from 1.94 to 4.84 using a 5% acetonitrile/water mixture as the soil solution. Its two metabolites had a higher sorption affinity for soils, with Kf values ranging from 11.09 to 23.49 for the sulfide derivative and from 4.70 to 11.77 for the desulfynil derivative. Their sorption coefficients were found to be better related to the soil organic carbon than clay content. The presence of cosolvents in soil solutions had a significant influence on the sorption of fipronil. The Freundlich sorption coefficients showed a log linear relationship with the fractions of both acetonitrile and methanol in solutions. The sorption coefficient of fipronil on Turretfield soil in the aqueous solution was estimated to be from 13.80 to 19.19. Methanol had less effect on the sorption of fipronil than acetonitrile. The Kd values for fipronil on the eight soils using a 5% methanol/water mixture were from 5.34 to 13.85, which reflect more closely the sorption in the aqueous solution. The average Koc value for fipronil on the eight South Australian soils was calculated to be 825+/-214.     

Application of a mechanistic desorption-biodegradation model to describe the behavior of polycyclic aromatic hydrocarbons in peat soil aggregates

A procedure was developed to obtain three size fractions (2360 < d(p) < 1000, 1000 < d(p) < 710, and 710 < d(p) < 425 microm) of stable aggregates from Koopveen peat soil by application of an intense mixing regime prior to sieving of the soil material. The organic matter content, aggregation structure and the microstructure of these aggregates were determined and the particles were artificially contaminated with naphthalene and phenanthrene via a solvent phase. A nonlinear Freundlich sorption isotherm was determined for the naphthalene contaminated soil aggregates (n = 0.39; K(F) = 1.13 x 10(-2) m(1.17) kg(-0.39)). The applicability of a mathematical model, that describes sorption equilibrium, intraparticle mass-transfer, and nonlinear bacterial degradation kinetics, was tested by fitting results of dynamic desorption and biodegradation experiments, generated in this study and earlier work on the peat soil aggregates. The experimental data were described adequately although strong variations in the values of the fit parameter, the intra-particle porosity (0.30 < epsilon < 0.88), were found. This indicates the necessity of further investigations.     

Sorption of weak organic acids in soils: clofencet, 2,4-D and salicylic acid.

The sorption behaviour of a new wheat hybridising agent (clofencet, 2-4-(chlorophenyl)-3-ethyl-2,5-dihydro-5-oxopyridazine-4-carboxylic acid) was investigated in batch equilibrium experiments and compared to that of two other organic acids (2,4-D and salicylic acid). Sorption coefficients Kd for the three compounds were determined in 18 Cambisols and Ferralsols. Kd values for clofencet were 0.3-9.4 l/kg for Cambisols and 2.1-68 l/kg for Ferralsols. Sorption of clofencet was strongly related statistically to that of salicylic acid. Sorption of clofencet and salicylic acid decreased exponentially with increasing solution pH in Cambisols whereas a bell-shaped curve was obtained for the sorption of salicylic acid in Ferralsols. Sorption of 2,4-D (2,4-dichlorophenoxyacetic acid) was not statistically related to the pH of the different soils. Positively charged oxide surfaces were shown to play a significant role in the sorption of clofencet and salicylic acid. The use of simple correlation and multiple linear regressions suggested that the main sorption mechanisms of clofencet in soils were likely to be ligand exchange on oxide surfaces and, to a lesser extent, cation bridging. Differences in the sorption behaviour of clofencet/salicylic acid and 2,4-D might be attributed to the possibility of the two former compounds forming bidentate complexes with metals.     

Antimony mobility in Japanese agricultural soils and the factors affecting antimony sorption behavior

The mobility of antimony (Sb) in Japanese agricultural soils was studied by radiotracer experiments using 124Sb tracer. The soil-solution distribution coefficients (Kd) of Sb were measured for 110 soil samples. These Kds ranged from 1 to 2065 L kg(-1); the geometric mean was 62 L kg(-1) excluding one extremely high value, 2065 L kg(-1). Experimental measurement of Kd showed a decrease with both increasing pH and increasing phosphate concentration. The latter suggested that one aspect of the Sb sorption phenomena in Japanese soil was influenced by specific adsorption of anions such as phosphate. However, other aspects could not be explained by this specific adsorption mechanism, because only 20-40% of soil-sorbed Sb could be extracted by phosphate solution.     

Effect of organic fertilizers derived dissolved organic matter on pesticide sorption and leaching

Incorporation of organic fertilizers/amendments has been, and continues to be, a popular strategy for golf course turfgrass management. Dissolved organic matter (DOM) derived from these organic materials may, however, facilitate organic chemical movement through soils. A batch equilibrium technique was used to evaluate the effects of organic fertilizer-derived DOM on sorption of three organic chemicals (2,4-D, naphthalene and chlorpyrifos) in USGA (United States Golf Association) sand, a mixed soil (70% USGA sand and 30% native soil) and a silt loam soil (Typic Fragiochrept). DOM was extracted from two commercial organic fertilizers. Column leaching experiments were also performed using USGA sand. Sorption experiments showed that sorption capacity was significantly reduced with increasing DOM concentration in solution for all three chemicals. Column experimental results were consistent with batch equilibrium data. These results suggest that organic fertilizer-derived DOM might lead to enhanced transport of applied chemicals in turf soils.     

Sorption of naphthoic acids and quinoline compounds to estuarine sediment

The sorption of 16 ionizable organic compounds (IOCs) to an estuarine sediment was measured in synthetic estuarine water as a function of IOC concentration (1-100 microM) at fixed ionic strength (0.4 M), pH (7.6), and sediment concentration (0.018 g sediment kg(-1) suspension). Of the 16 IOCs, 11 were naphthoic acids and five were quinoline compounds. The linear sorption distribution coefficient (Kd) was used to correlate sorption to IOC physicochemical and molecular characteristics. With respect to naphthoic acid, sorption increased with the addition of ortho-substituent groups and with increasing chain length of the 1-acid group, and the greatest increase occurred with ortho-hydroxyl, carbonyl, and carboxyl groups. With respect to quinoline, sorption decreased with substituent group addition (except for nitro group) and with additional heterocyclic N atoms. For the naphthoic acids, log Kd exhibited a positive correlation with water solubility (log Sw) indicative of sorption primarily to mineral surfaces under the solution chemistry. For the quinoline compounds, log Kd exhibited a negative correlation with log Sw and a positive correlation with n-octanol/water partition coefficient (log K(OW)) indicative of sorption primarily to organic matter. For both compounds, poor or no correlations were established between log Kd and acid dissociation constant (pKa1), and between log Kd and a variety of molecular connectivity indexes. The results from this study demonstrate that the sorption of IOCs differ depending on their backbone structure and may differ between parent compound and ionizable degradation product.     

Sorption of pentachlorophenol on peat-bentonite mixtures.

Batch kinetic and isotherm studies were carried out to determine the adsorptive characteristics of peat and bentonite mixtures for pentachlorophenol, and to examine the hydraulic conductivity of peat-bentonite mixtures to determine if they are applicable for use as cutoff barriers. Batch kinetic studies showed that over 90% of PCP was removed from water spiked with approximately 1 mg/l of PCP using a peat-bentonite (5%) mixture. The equilibrium time was 8 hours. The optimum pH range for adsorption of PCP by the peat-bentonite mixture was found to be 3-3.5. Batch isotherm studies showed that the adsorption of PCP by the peat-bentonite mixture from aqueous solution was best described by the Freundlich isotherm equation. Batch adsorption studies using various ratios of bentonite in the mixture showed that the adsorption of PCP decreased linearly with increased amount of bentonite in the mixture, indicating that adsorption of PCP by the peat moss portion of the mixture was the dominant process. The inverse of the hydraulic conductivity was found to increase exponentially with an increase in the bentonite content of the mixture over the range studied. The minimum hydraulic conductivity observed was 3.3 x 10(-7) cm/s for a 50% peat-50% bentonite mixture. Peat-bentonite mixtures can be used to successfully remove PCP from aqueous media and can be used effectively as a barrier to attenuate the migration of PCP through soil and groundwater systems.