Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

表面活性剂强化抽出处理含水层中DNAPL污染物的去除特征

为明确表面活性剂强化抽出处理含水层中DNAPL污染物过程中表面活性剂的增强修复效果,及DNAPL自身理化性质和介质孔径的影响,利用数码图像分析技术对1,2-二氯乙烷和四氯乙烯2种DNAPL在石英砂填充的二维砂箱中的抽取迁移过程进行了实验模拟研究,并对抽出水样中DNAPL的浓度进行了测试分析。结果表明,实验条件下加入低浓度(0.18%)的十二烷基苯磺酸钠(SDBS)大幅提高了对弱透水层截留的2种DNAPL聚集体的抽出处理效率。1,2-二氯乙烷在该表面活性剂溶液中的表观溶解度远高于四氯乙烯,因此其短时间内的绝对去除率更高。SDBS强化抽出处理DNAPL的作用机理以增溶作用为主,而其增流作用使DNAPL迁移流动后分布面积增大,增加了与表面活性剂溶液接触的面积,对增溶作用起到促进效果。细粒介质中DNAPL迁移后的最大分布面积较大,因此体系中DNAPL的溶解速率较高。在DNAPL聚集体质量与水力梯度固定的条件下,油水界面张力越低,DNAPL的密度越大,DNAPL垂向迁移的风险就越大。本研究为修复工程中如何依据DNAPL种类与场地多孔介质的情况选择表面活性剂提供了参考。     

Environmental features of two commercial surfactants widely used in soil remediation

One of the main limitations for a wider application of surfactants in soil remediation is the lack of knowledge about environmental fate and toxicity of surfactant itself especially for in situ application. Sorption behaviour, biodegradability, toxicity of parent compound and its metabolites are important processes that affect environmental fate of surfactants in site remediation applications. Tween 80 (poly(oxyethylene)(20)-sorbitane monooleate) and Aerosol MA+80 (dihexyl sodium sulfosuccinate) are surfactants that have been tested in laboratory and field scale remediation of soil and groundwater. In this work, the sorption and biodegradability of these surfactants were assessed to provide conditions and limitations for their use. The soil used in this experimentation was analysed for organic carbon content, soil bacteria, and size fraction and resulted to be a good model because is characterised by mean values for almost all considered parameters. Tween 80 showed high degree of biodegradability but a high affinity for soil matrix. Results suggest that Tween 80 could find its best application in ex situ solid phase remediation like ex situ bioremediation; its high affinity to soil could limit in situ applications. Biodegradation tests for Aerosol MA+80 show low degree of biodegradability and mineralisation. Biodegradation experiments, coupled with analysis of toxicity, could support the hypothesis that degradation of Aerosol MA+80 is not complete and leads to an accumulation of intermediates with at least the same toxicity of the parental compound. Therefore, aquifer remediation application with Aerosol MA+80 has to be conducted with necessary precautions to avoid product loss and excess surfactant should be flushed from the soil.     

Removal of DNAPL contamination from the saturated zone by the combined effect of vertical upward flushing and density reduction

A common aspect of innovative remediation techniques is that they tend to reduce the interfacial tension between the aqueous and non-aqueous phase liquids, resulting in mobilization of the organic contaminant. This complicates the remediation of aquifers, contaminated with Dense Non-Aqueous Phase Liquids (DNAPLs), as they are likely to migrate downwards, deeper into the aquifer and into finer layers. A possible solution is the use of swelling alcohols, which tend to reduce the density difference between the aqueous phase and the DNAPL. To avoid premature mobilization upon the initial contact between the DNAPL and the alcohol, several researchers have proposed the use of vertical upward flow of the alcohol. In this paper, we present an equation, which describes the upward mobilization of both continuous and discontinuous DNAPLs and so the important parameters governing the upward controlled mobilization of the DNAPL. The need and required magnitude of this specific discharge was investigated by conducting four column experiments in which the initial density of the DNAPL and the permeability was varied. It was shown that the required flow velocities increase with the permeability of the porous medium and the initial density difference between the aqueous phase and the DNAPL. Whenever the specific discharge falls below the critical value, the DNAPL moves downward. A second set of column experiments looked at the impact of permeability of porous medium on the solubilization and mobilization of DNAPL during alcohol flooding. Columns, packed with coarse or fine sand, containing a residual trichloroethylene (TCE) or perchloroethylene (PCE) saturation were flushed with the alcohol mixture at a fixed specific discharge rate. The induced pressure gradients in the aqueous phase, which were higher in the fine sand, resulted for this porous medium in extensive mobilization of the DNAPL against the direction of the buoyancy force. The density of the first NAPL coming out of the top of the fine sand was close to that of the pure DNAPL. In the coarser sand, the pressure gradients were sufficient to prevent downward migration of the DNAPL, but upward mobilization was minimal. The predominant removal mechanism in this case was the much slower solubilization.     

Mobilization and entry of DNAPL pools into finer sand media by cosolvents: two-dimensional chamber studies

Two-dimensional chamber studies were conducted to determine qualitative and quantitative performance of cosolvents targeted at pooled dense non-aqueous phase liquid (DNAPL) (perchlorethylene, PCE) residing above a fine-grain capillary barrier. Downward mobilization of DNAPL, up gradient along an overriding cosolvent front, was observed. This produced significant pooling above a fine-grain layer that in some cases lead to entry into the capillary barrier beneath. Entry pressure calculations using physical and hydrogeologic parameters provided an excellent prediction of breakthrough of DNAPL into the capillary barrier. Calculations predict approximately 0.5 m of DNAPL would be necessary to enter a Beit Netofa clay, under extreme cosolvent flooding conditions (100% ethanol). Gradient injection of cosolvent did not appear to provide any benefit suggesting a rapid decrease in interfacial tension (IFT) compared to the rate of DNAPL solubilization. Use of a partitioning alcohol (tertiary butyl alcohol, TBA) resulted in DNAPL swelling and reduced entry into the capillary barrier. However, the trapping of flushing solution, containing PCE, could potentially lead to longer remediation times.     

Determining effective interfacial tension and predicting finger spacing for DNAPL penetration into water-saturated porous media

The difficulty in determining the effective interfacial tension limits the prediction of the wavelength of fingering of immiscible fluids in porous media. A method to estimate the effective interfacial tension using fractal concepts was presented by Chang et al. [Water Resour. Res. 30 (1994) 125]. We modified the method in that the macroscopic interface length was used instead of the system width. Methods to determine the macroscopic and the microscopic interface length are given. Lab experiments of dense nonaqueous phase liquid (DNAPL) penetrating into water-saturated glass beads were carried out in a two-dimensional (2-D) transparent chamber. The displacement processes were recorded using a 35-mm camera or a video camera, which was directly connected to and controlled by a computer. Unlike the method of Chang et al. (1994), the modified method used here gives a constant value of the effective interfacial tension over time. The predicted wavelengths of fingering are relatively close to those observed except for the fine beads.     

Intermediate-scale 2D experimental investigation of in situ chemical oxidation using potassium permanganate for remediation of complex DNAPL source zones

In situ chemical oxidation is a technology that has been applied to speed up remediation of a contaminant source zone by inducing increased mass transfer from DNAPL sources into the aqueous phase for subsequent destruction. The DNAPL source zone can consist of one or more individual sources that may be present as an interconnected pool of high saturation, as a region of disconnected ganglia at residual saturation, or as combinations of these two morphologies. Potassium permanganate (KMnO(4)) is a commonly employed oxidant that has been shown to rapidly destroy DNAPL compounds like PCE and TCE following second-order kinetics in an aqueous system. During the oxidation of a target DNAPL compound, or naturally occurring reduced species in the subsurface, manganese oxide (MnO(2)) solids are produced. Research has shown that these manganese oxide solids may result in permeability reductions in the porous media thus reducing the ability for oxidant to be transported to individual DNAPL sources. It can also occur at the DNAPL-water interface, decreasing contact of the oxidant with the DNAPL. Additionally, MnO(2) formation at the DNAPL-water interface, and/or flow-bypassing as a result of permeability reductions around the source, may alter the mass transfer from the DNAPL into the aqueous phase, potentially diminishing the magnitude of any DNAPL mass depletion rate increase induced by oxidation. An experiment was performed in a two-dimensional (2D) sand-filled tank that included several discrete DNAPL source zones. Spatial and temporal monitoring of aqueous PCE, chloride, and permanganate concentrations was used to relate changes in mass depletion of, and mass flux, from DNAPL residual and pool source zones to chemical oxidation performance and MnO(2) formation. During the experiment, permeability changes were monitored throughout the 2D tank and these were related to MnO(2) deposition as measured through post-oxidation soil coring. Under the conditions of this experiment, MnO(2) formation was found to reduce permeability in and around DNAPL source zones resulting in changes to the overall flow pattern, with the effects depending on source zone configuration. A pool with little or no residual around it, in a relatively homogeneous flow field, appeared to benefit from resulting MnO(2) pore-blocking that substantially reduced mass transfer from the pool even though there was relatively little PCE mass removed from the pool. In contrast, a pool with residual around it (in a more typical heterogeneous flow field) appeared to undergo increased mass transfer as MnO(2) reduced permeability, altering the water flow and increasing the mixing at the DNAPL-water interface. Further, the magnitude of increased PCE mass depletion during oxidation appeared to depend on the PCE source configuration (pool versus ganglia) and decreased as MnO(2) was formed and deposited at the DNAPL-water interface. Overall, the oxidation of PCE mass appeared to be rate-limited by the mass transfer from the DNAPL to aqueous phase.     

Interphase mass transfer during chemical oxidation of TCE DNAPL in an aqueous system

The chemical oxidation of trichloroethene dense non-aqueous phase liquid by permanganate was studied in an aqueous system using micro-reaction/extraction vessels in a novel approach. Experiments were conducted at ambient temperature ( approximately 20 degrees C) under static and mixed conditions to evaluate the rate of TCE(DNAPL) dissolution as a function of permanganate concentration. Chemical oxidation by permanganate was shown to increase the rate of TCE(DNAPL) dissolution under static conditions and decrease the rate of dissolution under mixed conditions. The apparent inconsistency in results appears to result from the local deposition of a film at the DNAPL interface composed of manganese oxide solids as discovered through visual observation with the aid of a Goniometer. Data from interfacial deposition experiments suggest that the film formed rapidly and reached maturation within approximately 2 h with little or no growth occurring thereafter. A conceptual model of the reaction and mass transfer processes occurring at the DNAPL interface was proposed based on the experimental results.     

Improving the extraction of tetrachloroethylene from soil columns using surfactant gradient systems

In this work, we extend the recently developed gradient approach for surfactant-enhanced remediation of dense non-aqueous phase liquid (DNAPL)-impacted sites. The goal of the gradient approach is to maximize the DNAPL solubilization capacity in swollen micelles (Type I aqueous microemulsions) while at the same time minimizing the potential for DNAPL mobilization. In this work, we introduce a modified version of the capillary/trapping curve that we refer to as the gradient curve to help interpret and/or design the gradient approach. The gradient curve presents the residual DNAPL saturation as a function of interfacial tension and microemulsion viscosity. This approach demonstrates that keeping a low viscosity of the microemulsion phase is not only important for keeping a low head loss during surfactant flooding but also to prevent oil mobilization. Eight microemulsion systems were evaluated in this research; these systems were evaluated based on their tetrachloroethylene (PCE) solubilization capacity, interfacial tension (IFT), viscosity, density, and coalescence kinetics. Two of these systems were chosen for evaluation in site-specific column tests using an increasing electrolyte gradient to produce a decreasing IFT/increasing solubilization gradient system. The column studies were conducted with media from Dover Air Force Base in Dover, DE. Both solubilized and mobilized DNAPL were quantified. During the column studies, we observed that substantial PCE was mobilized when the residual level of PCE in the column was significantly higher than the steady-state residual saturation level being approach (as predicted from the gradient curve). Four column studies were performed, three of which were used to asses the validity of the gradient curve in predicting the residual saturation after each gradient step. From these tests we observed that starting IFTs of less than 1 mN/m all produced the same mobilization potential. In the last column, we used an additional gradient step with an initial IFT above 1 mN/m to dramatically reduce the amount of PCE mobilize. Based on the good agreement between column results and projections based on the gradient curve, we propose this as a preferred method for designing gradient surfactant flushing systems.     

Surfactant enhanced recovery of tetrachloroethylene from a porous medium containing low permeability lenses. 1. Experimental studies

A matrix of batch, column and two-dimensional (2-D) box experiments was conducted to investigate the coupled effects of rate-limited solubilization and layering on the entrapment and subsequent recovery of a representative dense NAPL, tetrachloroethylene (PCE), during surfactant flushing. Batch experiments were performed to determine the equilibrium solubilization capacity of the surfactant, polyoxyethylene (20) sorbitan monooleate (Tween 80), and to measure fluid viscosity, density and interfacial tension. Results of one-dimensional column studies indicated that micellar solubilization of residual PCE was rate-limited at Darcy velocities ranging from 0.8 to 8.2 cm/h and during periods of flow interruption. Effluent concentration data were used to develop effective mass transfer coefficient (Ke) expressions that were dependent upon the Darcy velocity and duration of flow interruption. To simulate subsurface heterogeneity, 2-D boxes were packed with layers of F-70 Ottawa sand and Wurtsmith aquifer material within 20-30 mesh Ottawa sand. A 4% Tween 80 solution was then flushed through PCE-contaminated boxes at several flow velocities, with periods of flow interruption. Effluent concentration data and visual observations indicated that both rate-limited solubilization and pooling of PCE above the fine layers reduced PCE recovery to levels below those anticipated from batch and column measurements. These experimental results demonstrate the potential impact of both mass transfer limitations and subsurface layering on the recovery of PCE during surfactant enhanced aquifer remediation.     

Mobilization of small DNAPL pools formed by capillary entrapment

We performed an experimental study to quantify the critical conditions for the mobilization of small pools of dense nonaqueous phase liquids (DNAPLs) that may form at capillary-heterogeneity boundaries. A series of experiments were conducted in columns packed with uniform sands arranged to create capillary heterogeneities. DNAPL pools readily formed in these packings and were more easily mobilized than trapped DNAPL ganglia. A model was developed to describe the critical conditions for DNAPL pool mobilization. Pool mobilization was expected when a dimensionless pool trapping number N(T)p> 1 while mobilization was observed in our experiments when N(T)p>0.76+/-0.16 (+/- 95% confidence interval). The difference between the model prediction and the experimental observations was attributed to experimental error. Using this model for DNAPL pool mobilization, a simple numerical experiment was conducted to illustrate use of the model and to explore the effect of scale on the critical conditions for pool mobilization. With an increase in system scale flow bypassing around the DNAPL pool increased and the system-averaged conditions for the onset of mobilization changed: a greater system-average Darcy flux or lower interfacial tensions were required for DNAPL pool mobilization. This result illustrates the importance of system scale on mobilization of DNAPL pools in systems with capillary heterogeneities.     

Refinement of the density-modified displacement method for efficient treatment of tetrachloroethene source zones

A novel method to remediate dense nonaqueous phase liquid (DNAPL) source zones that incorporates in situ density conversion of DNAPL via alcohol partitioning followed by displacement with a low interfacial tension (IFT) surfactant flood has been developed. Previous studies demonstrated the ability of the density-modified displacement (DMD) method to recover chlorobenzene (CB) and trichloroethene (TCE) from heterogeneous porous media without downward migration of the dissolved plume or free product. However, the extent of alcohol (n-butanol) partitioning required for in situ density conversion of high-density NAPLs, such as tetrachloroethene (PCE), could limit the utility of the DMD method. Hence, the objective of this study was to compare the efficacy of two n-butanol delivery approaches: an aqueous solution of 6% (wt) n-butanol and a surfactant-stabilized macroemulsion containing 15% (vol) n-butanol in water, to achieve density reduction of PCE-NAPL in two-dimensional (2-D) aquifer cells. Results of liquid-liquid equilibrium studies indicated that density conversion of PCE relative to water occurred at an n-butanol mole fraction of 0.56, equivalent to approximately 5 ml n-butanol per 1 ml of PCE when in equilibrium with an aqueous solution. In 2-D aquifer cell studies, density conversion of PCE was realized using both n-butanol preflood solutions, with effluent NAPL samples exhibiting density reductions ranging from 0.51 to 0.70 g/ml. Although the overall PCE mass recoveries were similar (91% and 93%) regardless of the n-butanol delivery method, the surfactant-stabilized macroemulsion preflood removed approximately 50% of the PCE mass. In addition, only 1.2 pore volumes of the macroemulsion solution were required to achieve in situ density conversion of PCE, compared to 6.4 pore volumes of the 6% (wt) n-butanol solution. These findings demonstrate that use of the DMD method with a surfactant-stabilized macroemulsion containing n-butanol holds promise as an effective source zone remediation technology, allowing for efficient recovery of PCE-DNAPL while mitigating downward migration of the dissolved plume and free product.     

Assessing the impacts of partial mass depletion in DNAPL source zones I. Analytical modeling of source strength functions and plume response

Analytical solutions are developed for approximating the time-dependent contaminant discharge from DNAPL source zones undergoing dissolution and other decay processes. The source functions assume a power relationship between source mass and chemical discharge and can consider partial DNAPL source remediation (depletion) at any time after the initial DNAPL release. The source functions are used as a time-dependent boundary condition in an idealized chemical transport model to develop leading order approximations of the plume response to DNAPL source removal. The results suggest that partial DNAPL remediation does not tend to have a dramatic impact on the maximum extent of the plume if very low concentration values are used to define the plume boundaries. However, the solutions show that partial DNAPL removal from the source zone is likely to lead to large reductions in plume concentrations and mass, and it reduces the longevity of the plume. When the mass discharge from the source zone is linearly related to the DNAPL mass, it is shown that partial DNAPL depletion leads to linearly proportional reductions in the plume mass and concentrations.     

Assessing impacts of partial mass depletion in DNAPL source zones: II. Coupling source strength functions to plume evolution

Analytical solutions, describing the time-dependent DNAPL source-zone mass and contaminant discharge rate, derived previously in Part I [Falta, R.W., Rao, P.S., Basu, N., this issue. Assessing the impacts of partial mass depletion in DNAPL source zones: I. Analytical modeling of source strength functions and plume response. J. Contam. Hydrol.] are used as a flux-boundary condition in a semi-analytical contaminant transport model. These analytical solutions assume a power relationship between the flow-averaged source concentration, and the source DNAPL mass; the empirical exponent (gamma) is a function of the flow field heterogeneity, DNAPL architecture, and the correlation between them. The DNAPL source strength terms can account for partial source remediation, either at time zero, or at some later time after the DNAPL release. The transport model considers advection, retardation, three-dimensional dispersion, and sequential first-order decay/production of several species. A separate solution is used to compute the time-dependent mass of each contaminant in the plume. A series of examples using different values of gamma shows how the benefits of partial DNAPL source remediation can vary with site conditions. In general, when gamma>1, relatively large short-term reductions in the plume concentrations and mass occur, but the source longevity is not strongly affected. Conversely, when gamma<1, the short-term reductions in the plume concentrations and mass are smaller, but the source longevity can be greatly reduced. In either case, the source remediation effort is much more effective if it is undertaken at an early time, before much contaminant mass has entered the plume. If the remediation effort is significantly delayed, the leading parts of the plume are not affected by the source remediation, and additional control or remediation of the plume itself is required.     

A multi-objective optimization framework for surfactant-enhanced remediation of DNAPL contaminations

The occurrence of Dense Non-Aqueous Phase Liquid (DNAPL) contaminations in the subsurface is a threat for drinkwater resources in the western world. Surfactant-Enhanced Aquifer Remediation (SEAR) is widely considered as one of the most promising techniques to remediate DNAPL contaminations in-situ, be it with considerable additional costs compared to classical pump-and-treat remediations. A cost-effective design of the remediation set-up is therefore essential. In this work, a pilot SEAR test is executed at a DNAPL contaminated site in Belgium in order to collect data for the calibration of a multi-phase multi-component model. The calibrated model is used to assess a series of scenario-analyses for the full-scale remediation of the site. The remediation variables that were varied were the injection and extraction rate, the injection and extraction duration, and the surfactant injection concentrations. A constrained multi-objective optimization of the model was applied to obtain a Pareto set of optimal remediation strategies with different weights for the two objectives of the remediation: (i) the maximal removal of DNAPL and (ii) a total minimal cost. These Pareto curves can help decision makers to select an optimal remediation strategy in terms of cost and remediation efficiency. The Pareto front shows a considerable trade-off between the total remediation cost and the removed DNAPL mass.     

Mass removal of chlorinated ethenes from rough-walled fractures using permanganate

In situ chemical oxidation (ISCO) employing permanganate is an emerging technology that has been successful at enhancing mass removal from DNAPL source zones in unconsolidated media at the pilot-scale. The focus of this study was to evaluate the applicability of flushing a permanganate solution across two single vertical fractures in a laboratory environment to remove free phase DNAPL. The fracture experiments were designed to represent a portion of a larger fractured aquifer system impacted by a near-surface DNAPL spill over a shallow fractured rock aquifer. Each fracture was characterized by hydraulic and tracer tests, and the aperture field for one of the fractures was mapped using a co-ordinate measurement machine. Following DNAPL emplacement, a series of water and permanganate flushes were performed. To support observations from the fracture experiments, a set of batch experiments was conducted. The data from both fracture experiments showed that the post-oxidation effluent concentration was not impacted by the oxidant flush; however, changes in the aperture distribution, flow field, and flow rate were observed. These changes resulted in a significant decrease to the mass loading from the fractures, and were attributed to the build-up of oxidation by-products (manganese oxides and carbon dioxide) within the fracture which was corroborated by the batch experiment data and visual examination of the walls of one fracture. These results provide insight into the potential impact that a permanganate solution and oxidation by-products can have on the aperture distribution within a fracture and on DNAPL mass transfer rates. A permanganate flush or injection completed within a fractured rock aquifer may lead to the development of an insoluble product adjacent to the DNAPL which results in the reduction or complete elimination of advective regions near the DNAPL and reduces mass transfer rates. This outcome would have significant implications on the plume generating potential of the remaining DNAPL.     

Influence of surfactant-facilitated interfacial tension reduction on chlorinated solvent migration in porous media: observations and numerical simulation

The ability of a multiphase flow model to capture the migration behavior of chlorinated solvents under conditions of surfactant-facilitated interfacial tension (IFT) reduction is assessed through comparison of model predictions with observations from controlled laboratory experiments. Tetrachloroethene (PCE) was released in two-dimensional saturated systems, packed with sandy media that incorporated rectangular lenses of capillary contrast. Spatially uniform interfacial tension conditions were created in the tanks by pre-flushing the porous medium with either Milli Q water or an aqueous surfactant solution. Experimental observations showed that surfactant-facilitated IFT reductions substantially lowered capillary resistance to the vertical downward migration of PCE and enabled PCE to enter finer grained, less permeable lenses that were not penetrated in the absence of surfactant. An immiscible flow model was used to simulate the conditions of the laboratory experiments. Under higher IFT conditions (47.5 and 5 dyn/cm), the model could successfully predict the general migration behavior of the organic liquid. Model predictions, however, exhibited poorer agreement with observed migration pathways under low IFT conditions (0.5 dyn/cm). In all cases, the predicted PCE distributions were influenced by selection of the parametric model for capillary retention and relative permeability. Simulated migration rates were more consistent with observed behavior when the Brooks-Corey/Burdine model was employed. For low interfacial tensions, improved predictions of migration pathways were obtained through grid refinement and incorporation of small-scale packing variability. Simulations highlight the substantial sensitivity of model predictions to the capillary pressure-scaling factor, grid resolution, and small-scale porosity variations at interfaces of permeability contrast under reduced IFT conditions.     

Laboratory investigation of flux reduction from dense non-aqueous phase liquid (DNAPL) partial source zone remediation by enhanced dissolution

This study investigated the benefits of partial removal of dense nonaqueous phase liquid (DNAPL) source zones using enhanced dissolution in eight laboratory scale experiments. The benefits were assessed by characterizing the relationship between reductions in DNAPL mass and the corresponding reduction in contaminant mass flux. Four flushing agents were evaluated in eight controlled laboratory experiments to examine the effects of displacement fluid property contrasts and associated override and underride on contaminant flux reduction (R(j)) vs. mass reduction (R(m)) relationships (R(j)(R(m))): 1) 50% ethanol/50% water (less dense than water), 2) 40% ethyl-lactate/60% water (more dense than water), 3) 18% ethanol/26% ethyl-lactate/56% water (neutrally buoyant), and 4) 2% Tween-80 surfactant (also neutrally buoyant). For each DNAPL architecture evaluated, replicate experiments were conducted where source zone dissolution was conducted with a single flushing event to remove most of the DNAPL from the system, and with multiple shorter-duration floods to determine the path of the R(j)(R(m)) relationship. All of the single-flushing experiments exhibited similar R(j)(R(m)) relationships indicating that override and underride effects associated with cosolvents did not significantly affect the remediation performance of the agents. The R(j)(R(m)) relationship of the multiple injection experiments for the cosolvents with a density contrast with water tended to be less desirable in the sense that there was less R(j) for a given R(m). UTCHEM simulations supported the observations from the laboratory experiments and demonstrated the capability of this model to predict R(j)(R(m)) relationships for non-uniformly distributed NAPL sources.     

The significance of heterogeneity on mass flux from DNAPL source zones: an experimental investigation

Understanding the process of mass transfer from source zones of aquifers contaminated with organic chemicals in the form of dense non-aqueous phase liquids (DNAPL) is of importance in site management and remediation. A series of intermediate-scale tank experiments was conducted to examine the influence of aquifer heterogeneity on DNAPL mass transfer contributing to dissolved mass emission from source zone into groundwater under natural flow before and after remediation. A Tetrachloroethylene (PCE) spill was performed into six source zone models of increasing heterogeneity, and both the spatial distribution of the dissolution behavior and the net effluent mass flux were examined. Experimentally created initial PCE entrapment architecture resulting from the PCE migration was largely influenced by the coarser sand lenses and the PCE occupied between 30 and 60% of the model aquifer depth. The presence of DNAPL had no apparent effect on the bulk hydraulic conductivity of the porous media. Up to 71% of PCE mass in each of the tested source zone was removed during a series of surfactant flushes, with associated induced PCE mobilization responsible for increasing vertical DNAPL distributions. Effluent mass flux due to water dissolution was also found to increase progressively due to the increase in NAPL-water contact area even though the PCE mass was reduced. Doubling of local groundwater flow velocities showed negligible rate-limited effects at the scale of these experiments. Thus, mass transfer behavior was directly controlled by the morphology of DNAPL within each source zone. Effluent mass flux values were normalized by the up-gradient DNAPL distributions. For the suite of aquifer heterogeneities and all remedial stages, normalized flux values fell within a narrow band with mean of 0.39 and showed insensitivity to average source zone saturations.     

Effect of scale and dimensionality on the surfactant-enhanced solubilization of a residual DNAPL contamination

The mass transfer rate from residual dense non-aqueous phase liquids (DNAPLs) to the mobile aqueous phase is an important parameter for the efficiency of surfactant-enhanced remediation through solubilization of this type of contamination. The mass transfer kinetics are highly dependent on the dimensionality of the system. In this study, irregularly shaped residual TCE saturations in two-dimensional saturated flow fields were flushed with a 2% polyoxyethylene sorbitan (20) monooleate (POESMO) solution until complete removal had been achieved. A numerical model was developed and used for the simulation of the various surfactant-flushing experiments with different initial saturation patterns and flow rates. Through optimization against in situ concentration and saturation data, a phenomenological power-law model for the relationship between the mass transfer rate from the DNAPL to the mobile aqueous phase on the one hand and the residual DNAPL saturation and the flow velocity on the other hand was derived. The obtained mass transfer rate parameters provide a reasonable fit to the experimental data, predicting the cleanup time and the general saturation and concentration pattern quite well but failing to predict the concentration curves at every individual sampling port. The obtained mass transfer rate model gives smaller values for the predicted mass transfer rate but shows a comparable dependence on water flow and saturation as in earlier published one-dimensional column experiments with identical characteristics for porous medium, DNAPL and surfactant. Mass transfer rate predictions were about one order of magnitude lower in the 2-D flow cell experiment than in 1-D column experiments. These results give an indication for the importance of dimensionality during surfactant remediation.