Sequential box models for indoor air quality: Application to airliner cabin air quality

In this paper we present the development and application of a model for indoor air quality. The model represents a departure from the standard box models typically used for indoor environments which has applicability in residences and office buildings. The model has been developed for a physical system consisting of sequential compartments which communicate only with adjacent compartments. Each compartment may contain various source and sink terms for a pollutant as well as leakage, and air transfer from adjacent compartments. The mathematical derivation affords rapid calculation of equilibrium concentrations in an essentially unlimited number of compartments. The model has been applied to air quality in the passenger cabin of three commercial aircraft. Simulations have been performed for environmental tobacco smoke (ETS) under two scenarios, CO₂ and water vapor. Additionally, concentrations in one aircraft have been simulated under conditions different from the standard configuration. Results of the simulations suggest the potential for elevated concentrations of ETS in smoking sections of non-air-recirculating aircraft and throughout the aircraft when air is recirculated. Concentrations of CO₂ and water vapor are consistent with expected results. We conclude that this model may be a useful tool in understanding indoor air quality in general and on aircraft in particular.     

Jet Aircraft Operations: Impact on the Air Environment

This paper is directed to those concerned with the air environment and its degradation by the burden of pollution from jet aircraft operations. A summary is presented of the results of a comprehensive air pollution study of jet aircraft operations at the Los Angeles International Airport (LAX). Included in the data obtained from this study are jet engine exhaust measurements for currently used turboprop, turbojet and turbofan engines; measurements of specific contaminants in the atmosphere inside and outside of passenger terminals and ticketing areas, and in aircraft cabins during ground operations including passenger loading and taxiing prior to takeoff; also presented are ambient air measurements in a two-mile radius of the airport. An evaluation is made of the emissions of contaminants from air transport operations and all related ground activities including motor vehicles, that contribute to the total atmospheric contaminant burden at the airport.     

Isokinetic Sampler for Continuous Airborne Aerosol Measurements

For aerosol measurements, especially those concerned with the aerosol particle size distribution, it is important to sample in isokinetic conditions. Most available instrumentation for aerosol measurements is intended for use on the ground under light wind conditions; intake air speeds rarely exceed a few meters per second. If the same instrumentation is used onboard an aircraft, the air must be decelerated 60 or more m/sec before It is sampled by individual instruments.

On The Pennsylvania State University Meteorology research aircraft, the air for all aerosol instruments is decelerated in a single isokinetic sampler located above the roof of the cabin outside the aircraft boundary layer. The air enters the sampler through a carefully designed circular intake. Its velocity is reduced as the cross section increases along a 7° conical diffuser. The expansion cone terminates in a cylindrical chamber in which the air velocity is 1/16 the aircraft speed. Behind the sampling chamber the air is accelerated in a second conical section to an end exhaust port. Exhaust porf "pumping" is used to compensate internal losses and, thus, helps preserve the isokinetic nature of the sampler.

Tubes leading to individual instruments are located in the sampling chamber and may be individually adapted to match the air sampling velocity with the local air speed inside the sampling chamber. The level of turbulence (u_rms/û) in the sampling section is =^0.05.

The sampler has been thoroughly wind tunnel and flight tested and successfully used in August and November, 1974, for field programs in the St. Louis and Tucson metropolitan areas, respectively.     

Polybrominated diphenyl ethers in aircraft cabins--a source of human exposure?

Commercial aircrafts need a high degree of fire protection for passenger safety. Brominated flame retardants (BFRs), including polybrominated diphenyl ethers (PBDEs), may be used for this purpose. Because PBDEs readily absorb to dust particles, aircraft crew and passengers may receive significant PBDEs exposure via inhalation. The aims of this work were to assess whether PBDEs could be found in aircraft cabin dust and whether serum levels of PBDEs increased in passengers after long-distance flights. Hence nine subjects on intercontinental flights collected cabin dust samples, as well as donated blood samples before departure and after return to Sweden. Two subjects who were domestic frequent flyers were also investigated. The levels of PBDEs in dust and serum were determined by GC/MS in electron capture negative ionization (ECNI) mode. Authentic reference substances were used for identification and quantitation. PBDEs were found in all aircraft dust samples at high concentrations, higher than in common household dust. Congener patterns indicated that the technical products PentaBDE, OctaBDE and DecaBDE were used in the aircrafts. Serum concentrations in the travellers were similar to those observed in Swedish residents in general. Post-travel serum levels of BDE-28, BDE-99, BDE-100, BDE-153, and BDE-154 were significantly higher (p<0.05) than concentrations prior to travel. The findings from this pilot study call for investigations of occupational exposures to PBDEs in cabin and cockpit crews.     

Simulation of the Environmental Impact of an Airport on the Surrounding Air Quality

It is the purpose of this study to demonstrate the procedure involved in simulating those average and maximum pollutant concentrations at or around an airport which fall under the control of the Clean Air Act. The information is useful, when planning new or expanding existing airports, when estimating the impact of airports on the surrounding air quality, and when assessing the effectiveness of control procedures. Simulation of airport air quality requires the accurate assessment of the temporal and spatial emission patterns. This involves the tabulation of air traffic density by type and engine, make and model of aircraft, and engine mode number; the use of fuel by different aircraft; the pollutant emission rates by engine model and operational mode; the allocation of emission rates to the respective runways, turn-off points, taxi-ways, and parking areas, and the time each aircraft spent in the different operational modes. The resulting emission pattern for the Honolulu International Airport reflects scheduled and unscheduled commercial and military jet and piston aircraft and nonaircraft operations. Using this and the appropriate meteorological information average and maximum surface concentrations were calculated and compared with local ambient air quality standards. The calculation of concentrations is based on a newly developed diffusion model incorporating harmonic mean wind speeds for every degree of wind direction as determined by a Parzen maximum likelihood interpolation technique, and the assumption of log-normal concentration distributions. It is shown that for some pollutants the air quality standards are substantially exceeded, and it is concluded that airports may have a considerable adverse impact on their surrounding air quality.     

Air quality mapping using GIS and economic evaluation of health impact for Mumbai City,India

Mumbai, a highly populated city in India, has been selected for air quality mapping and assessment of health impact using monitored air quality data. Air quality monitoring networks in Mumbai are operated by National Environment Engineering Research Institute (NEERI), Maharashtra Pollution Control Board (MPCB), and Brihanmumbai Municipal Corporation (BMC). A monitoring station represents air quality at a particular location, while we need spatial variation for air quality management. Here, air quality monitored data of NEERI and BMC were spatially interpolated using various inbuilt interpolation techniques of ArcGIS. Inverse distance weighting (IDW), Kriging (spherical and Gaussian), and spline techniques have been applied for spatial interpolation for this study. The interpolated results of air pollutants sulfur dioxide (SO₂), nitrogen dioxide (NO₂) and suspended particulate matter (SPM) were compared with air quality data of MPCB in the same region. Comparison of results showed good agreement for predicted values using IDW and Kriging with observed data. Subsequently, health impact assessment of a ward was carried out based on total population of the ward and air quality monitored data within the ward. Finally, health cost within a ward was estimated on the basis of exposed population. This study helps to estimate the valuation of health damage due to air pollution.

Implications: Operating more air quality monitoring stations for measurement of air quality is highly resource intensive in terms of time and cost. The appropriate spatial interpolation techniques can be used to estimate concentration where air quality monitoring stations are not available. Further, health impact assessment for the population of the city and estimation of economic cost of health damage due to ambient air quality can help to make rational control strategies for environmental management. The total health cost for Mumbai city for the year 2012, with a population of 12.4 million, was estimated as USD8000 million.     

In-vehicle carbon dioxide concentration in commuting cars in Bangkok,Thailand

It is known that in-vehicle carbon dioxide (CO₂) concentration tends to increase due to occupant exhalation when the HVAC (heating, ventilation, and air conditioning) air is in recirculation mode. Field experiments were conducted to measure CO₂ concentration during typical commute in Bangkok, Thailand. The measured concentrations agreed with the concentration predicted using first-order mass balance equation, in both recirculating and outside air modes. The long-term transient decay of the concentration when the vehicle was parked and the HVAC system was turned off was also studied. This decay was found to follow Fickian diffusion process. The paper also provides useful operational details of the automotive HVAC system and fresh air ventilation exchange between cabin interior and exterior.

Implications: Drivers in tropical Asian countries typically use HVAC recirculation mode in their automobiles. This behavior leads to excessive buildup of cabin CO₂ concentration levels. The paper describes the CO₂ buildup in a typical commute in Bangkok, Thailand. Auto manufacturers can potentially take measures to alleviate such high concentration levels. The paper also discusses the diffusion of CO₂ through the vehicle envelope, an area that has never been investigated before.     

Controlling air pollution from passenger ferries: cost-effectiveness of seven technological options

Continued interest in improving air quality in the United States along with renewed interest in the expansion of urban passenger ferry service has created concern about air pollution from ferry vessels. This paper presents a methodology for estimating the air pollution emissions from passenger ferries and the costs of emissions control strategies. The methodology is used to estimate the emissions and costs of retrofitting or re-powering ferries with seven technological options (combinations of propulsion and emission control systems) onto three vessels currently in service in San Francisco Bay. The technologies include improved engine design, cleaner fuels (including natural gas), and exhaust gas cleanup devices. The three vessels span a range of ages and technologies, from a 25-year-old monohull to a modern, high-speed catamaran built only four years ago. By looking at a range of technologies, vessel designs, and service conditions, a sense of the broader implications of controlling emissions from passenger ferries across a range of vessels and service profiles is provided. Tier 2-certified engines are the most cost-effective choice, but all options are cost-effective relative to other emission control strategies already in place in the transportation system.     

Reducing Air Pollutant Emissions at Airports by Controlling Aircraft Ground Operations

Potential reductions in air pollutant emissions were determined for four strategies to control aircraft ground operations at two case study airports, Los Angeles and San Francisco International Airports. Safety, cost, and fuel savings associated with strategy implementation were examined.

Two strategies, aircraft towing and shutdown of one engine during taxi operations, provided significant emission reductions. However, there are a number of safety problems associated with aircraft towing. The shutdown of one engine while taxiing was found to be the most viable strategy because of substantial emission reductions, cost benefits resulting from fuel savings, and no apparent safety problems.     

The influence of passenger activities on exposure to particles inside buses

Elevated personal exposures to particles have been reported in buses, but the factors associated with these high exposures are uncertain, and the potential role of passenger activities within buses has not been quantified. To improve understanding of this factor we measured particle number concentrations in the range 0.3–15 μm simultaneously inside and outside buses in the city of York (UK), while carefully noting passenger activities. We also developed a box model to simulate the effects of passenger activities, and parameterised this from independent studies with controlled passenger activities. The number concentrations inside buses were significantly higher than those outside in all size classes, and the inside/outside ratios increased with particle size. The model showed broad agreement with measured particle concentrations inside buses, and demonstrated, for particles in the range 3–15 μm, that both re-suspension by passenger activities and deposition to the surface of the passengers had significant effects on concentrations. Hence, understanding of the effects of passenger activities on both particle deposition and re-suspension is essential to interpret exposure measurements inside buses. Exposure of regular commuters inside buses could be of potential health significance and needs further assessment.     

Rapid measurement of emissions from military aircraft turbine engines by downstream extractive sampling of aircraft on the ground: Results for C-130 and F-15 aircraft

Aircraft emissions affect air quality on scales from local to global. More than 20% of the jet fuel used in the U.S. is consumed by military aircraft, and emissions from this source are facing increasingly stringent environmental regulations, so improved methods for quickly and accurately determining emissions from existing and new engines are needed. This paper reports results of a study to advance the methods used for detailed characterization of military aircraft emissions, and provides emission factors for two aircraft: the F-15 fighter and the C-130 cargo plane. The measurements involved outdoor ground-level sampling downstream behind operational military aircraft. This permits rapid change-out of the aircraft so that engines can be tested quickly on operational aircraft. Measurements were made at throttle settings from idle to afterburner using a simple extractive probe in the dilute exhaust. Emission factors determined using this approach agree very well with those from the traditional method of extractive sampling at the exhaust exit. Emission factors are reported for CO₂, CO, NO, NO_x, and more than 60 hazardous and/or reactive organic gases. Particle size, mass and composition also were measured and are being reported separately. Comparison of the emissions of nine hazardous air pollutants from these two engines with emissions from nine other aircraft engines is discussed.     

The impact of NOx,CO and VOC emissions on the air quality of Zurich airport

To study the impact of emissions at an airport on local air quality, a measurement campaign at the Zurich airport was performed from 30 June 2004 to 15 July 2004. Measurements of NO, NO₂, CO and CO₂ were conducted with open path devices to determine real in-use emission indices of aircraft during idling. Additionally, air samples were taken to analyse the mixing ratios of volatile organic compounds (VOC). Temporal variations of VOC mixing ratios on the airport were investigated, while other air samples were taken in the plume of an aircraft during engine ignition. CO concentrations in the vicinity of the terminals were found to be highly dependent on aircraft movement, whereas NO concentrations were dominated by emissions from ground support vehicles. The measured emission indices for aircraft showed a strong dependence upon engine type. Our work also revealed differences from emission indices published in the emission data base of the International Civil Aviation Organisation. Among the VOC, reactive C₂–C₃ alkenes were found in significant amounts in the exhaust of an engine compared to ambient levels. Also, isoprene, a VOC commonly associated with biogenic emissions, was found in the exhaust, however it was not detected in refuelling emissions. The benzene to toluene ratio was used to discriminate exhaust from refuelling emission. In refuelling emissions, a ratio well below 1 was found, while for exhaust this ratio was usually about 1.7.     

A Cost-Benefit Approach to Air Pollution Control

Air pollution has plagued the urban areas of our Nation for many years, both as a serious health hazard and as a costly economic burden. Users of the air as a waste disposal medium have treated it as a free resource with no regard for the damages incurred by receptors of the dirty air. Unfortunately, no self-regulating market forces exist that will bring this diseconomy into an acceptable equilibrium. An outside regulating force, which can affect abatement of air pollution, is needed to achieve control of air pollution to a level acceptable to a community. A prerequisite of any proposed regulatory action to be applied by an outside force, however, is the need to define an acceptable level of pollution. One means of accomplishing the task is to apply an economic evaluation, in the form of a cost-benefit analysis, to the problem. Previous analyses of the economic aspects of air pollution have stressed only one side of the problem. That is, they have dealt only with the cost of control or the damages caused by air pollution. No analysis has combined both aspects into a meaningful analysis of the overall economic impact. The objective of this paper is to present a technique that can be used to find the level of pollution abatement in an area that balances the cost of controlling pollution with the benefits received from its control. To present a clearer picture of this technique and its results, it has been applied to the Washington, D. C. area to find the optimum level of particulate abatement. This method is generally applicable to any area, in which an air pollution problem exists.     

Brominated flame retardants in dust from UK cars--within-vehicle spatial variability, evidence for degradation and exposure implications

Polybrominated diphenyl ethers (PBDEs), hexabromocyclododecanes (HBCDs), and tetrabromobiphenol-A (TBBP-A) were measured in a preliminary study of dust from passenger cabins and trunks of 14 UK cars. Concentrations in cabin dust of HBCDs, TBBP-A, and BDEs 47, 85, 99, 100, 153, 154, 183, 196, 197, 202, 203, 206, 207, 208, and 209 exceeded significantly (p < 0.05) those in trunk dust. Sampling cabin dust thus appears to provide a more accurate indicator of human exposure via car dust ingestion than trunk dust. Elevated cabin concentrations are consistent with greater in-cabin use of BFRs. In five cars, while no significant differences (p > 0.05) in concentrations of HBCDs and most PBDEs were detected in dust sampled from four different seating areas; concentrations of TBBP-A and of PBDEs 154, 206, 207, 208, and 209 were significantly higher (p < 0.05) in dust sampled in the front seats. Possible photodebromination of BDE-209 was indicated by significantly higher (p < 0.05) concentrations of BDE-202 in cabin dust. In-vehicle exposure via dust ingestion to PBDEs, HBCDs and TBBP-A exceeded that via inhalation. Comparison with overall exposure via diet, dust ingestion, and inhalation shows while in-vehicle exposure is a minor contributor to overall exposure to BDE-99, ΣHBCDs, and TBBP-A, it is a significant pathway for BDE-209.     

A Finite Line Source Dispersion Model for Mobile Source Air Pollution

The body of information presented in this paper is directed to individuals interested in dispersion modeling, and in particular to those concerned with evaluation of air quality in the vicinities of airports and roadways. The paper describes briefly the formulation and application of a finite line source dispersion model constructed on the basis of a Gaussian-type transport kernel. The formulation is sufficiently general that any arbitrary orientation of the line can be handled. For cases where the line is at small angles with respect to the wind, approximate expressions as well as segmentation of the line, if necessary, are used. These are Integrated into the general algorithmic scheme by means of a series of geometric tests. The general capabilities of the model are tested first with some hypothetical cases and then with actual air quality data. The latter case studies correspond to three separate periods of air quality monitoring at O’Hare Airport during which the aircraft emissions and the ground vehicle emissions play alternately important roles. The generally good agreement between model predictions and air quality data provides support for the validity of the approach. The overall efficiency of the model in terms of computer time as well as its limitations are briefly discussed.     

Crowded skies: Conflicts between expanding goose populations and aviation safety

We here review the collision risks posed by large-bodied, flocking geese to aircraft, exacerbated by recent major increases in northern hemisphere goose populations and air traffic volume. Mitigation of goose–aircraft strike risks requires knowledge of local goose movements, global goose population dynamics and ecology. Airports can minimise goose strikes by managing habitats within the airport property, applying deterrents to scare geese away and lethal control, but goose migration and movements at greater spatial scales present greater challenges. Habitat management outside of airports can locally reduce goose attractiveness of peripheral areas, but requires stakeholder involvement and coordination. Information on bird strike rates, individual goose movements and goose population dynamics is essential to understand how best to reduce the risk of goose strikes. Avian radar provides tactical information for mitigation measures and strategic data on local patterns of goose migration and habitat use. In the face of expanding air traffic, goose distributions and populations, these threats need to be integrated with other local, national and international stakeholder involvement to secure viable solutions to multiple conflicts.     

European abatement of surface ozone in a global perspective

EU's programme Clean Air for Europe (CAFE) is presently revising the policy on air quality which will lead to the adoption of a thematic strategy on air pollution under the Sixth Environmental Action Programme by mid-2005. For the abatement of surface ozone it is becoming evident that processes outside European control will be crucial for meeting long-term aims and air quality guidelines in Europe in the future. Measurements and modelling results indicate that there is a strong link between climate change and surface ozone. A warmer and dryer European climate is very likely to lead to increased ozone concentrations. Furthermore, increased anthropogenic emissions in developing economies in Asia are likely to raise the hemispheric background level of ozone. A significant increase in the background concentration of ozone has been observed at several sites in Northern Europe although the underlying causes are not settled. The photochemical formation of tropospheric ozone from increased concentrations of methane and CO may also lead to a higher ozone level on a global scale. Gradually, these effects may outweigh the effect of the reduced European ozone precursor emissions. This calls for a global or hemispheric perspective in the revision of the European air quality policy for ozone.     

Measurements of Pollutants inside an Automobile

A series of experiments was conducted to determine the concentration of certain pollutants inside a car under typical driving conditions. The work was performed during the summer months in the Los Angeles area and measurements of O₃, CO, NO, and NO_x were taken. It was found that the O₃ concentration in the passenger compartment may be maintained at relatively low values provided that the influx of outside air is limited. The low levels were explained by decay of O₃ on surfaces within the compartment. The average concentration of the other components inside the car is about equal to that on the outside. In the current tests, however, the measured concentrations did not exceed any of the present standards.