Characterization and source presumption of wintertime submicron organic aerosols at Saitama,Japan, using the Aerodyne aerosol mass spectrometer

The chemical composition and size distribution of submicron aerosols were analyzed at a suburban site at Saitama, Japan, in the winter of 2004/2005, using an Aerodyne aerosol mass spectrometer. Although organics and nitrate were the dominant species during the sampling period, a large fraction of sulfate was observed at the accumulation mode when mass loading was low and wind speed was high. The size distributions of m/z 44 (mostly CO₂⁺) and sulfate aerosols during periods of high wind speed showed remarkable similarities in the accumulation mode, indicating that oxygenated organics were aged aerosols and internally mixed with sulfate. Ozone concentrations were also increased during these high wind speed periods although nighttime (e.g., 12/17 2004), indicating that the oxygenated compounds were strongly influenced by transported and aged air masses. The diurnal profiles of ultrafine-mode organics and hydrocarbon-like organic aerosols (HOA) were similar to NO_X derived from traffic and other combustion sources. The temporal variation of oxygenated organic aerosols (OOA) agreed well with that of nitrate as a secondary aerosol tracer, and the diurnal profile of the OOA fraction of organics increased during the day associated with higher UV light intensity. The result of time and size-resolved chemical composition of submicron particles indicated that the OOA is associated with both photochemical activity and transboundary pollution, and ultrafine-mode organic and HOA aerosols are mainly associated with combustion sources.     

Sources of fine particle composition in the northeastern US

Fine particle composition data obtained at three sampling sites in the northeastern US were studied using a relatively new type of factor analysis, positive matrix factorization (PMF). The three sites are Washington, DC, Brigantine, NJ and Underhill, VT. The PMF method uses the estimates of the error in the data to provide optimal point-by-point weighting and permits efficient treatment of missing and below detection limit values. It also imposes the non-negativity constraint on the factors. Eight, nine and 11 sources were resolved from the Washington, Brigantine and Underhill data, respectively. The factors were normalized by using aerosol fine mass concentration data through multiple linear regression so that the quantitative source contributions for each resolved factor were obtained. Among the sources resolved at the three sites, six are common. These six sources exhibit not only similar chemical compositions, but also similar seasonal variations at all three sites. They are secondary sulfate with a high concentration of S and strong seasonal variation trend peaking in summer time; coal combustion with the presence of S and Se and its seasonal variation peaking in winter time; oil combustion characterized by Ni and V; soil represented by Al, Ca, Fe, K, Si and Ti; incinerator with the presence of Pb and Zn; sea salt with the high concentrations of Na and S. Among the other sources, nitrate (dominated by NO₃⁻) and motor vehicle (with high concentrations of organic carbon (OC) and elemental carbon (EC), and with the presence of some soil dust components) were obtained for the Washington data, while the three additional sources for the Brigantine data were nitrate, motor vehicle and wood smoke (OC, EC, K). At the Underhill site, five other sources were resolved. They are wood smoke, Canadian Mn, Canadian Cu smelter, Canadian Ni smelter, and another salt source with high concentrations of Cl and Na. A nitrate source similar to that found at the other sites could not be obtained at Underhill since NO₃⁻ was not measured at this site. Generally, most of the sources at the three sites showed similar chemical composition profiles and seasonal variation patterns. The study indicated that PMF was a powerful factor analysis method to extract sources from the ambient aerosol concentration data.     

Biotransformation of Herbicides in the Presence of Various Electron Acceptors

Abstract

Among the important factors affecting the biotransformation of xenobiotic chemicals upon their release into the environment are the dominant electron acceptor condition present and the presence of other, more readily degraded carbon sources. Here, glass-bead biofilm columns were used to investigate the effects of the presence of three different inorganic electron acceptor conditions (oxygen respiration, nitrate reduction, and sulfate reduction) on the biotransformation of the acetanilide herbicides alachlor and propachlor, and to determine the effects of two exogenous carbon sources (acetate and glucose) on their biotransformation under each of these conditions.

Biotransformation of alachlor and propachlor occurred in the presence of both carbon sources and under each of the three electron acceptor conditions. Both were transformed most rapidly under sulfate-reducing conditions. Analysis by gas chromatography/mass spectrometry (GC/MS) did not reveal any significant metabolic products. Both herbicides react abiotically with bisulfide, produced within the sulfate-reducing cultures, though most of the transformation was attributed to the microorganisms. The primary, readily degraded carbon source (acetate or glucose) was needed to establish each culture, and its continuous presence was required to sustain herbicide biotransformation in the sulfate-reducing reactors. Loss of either acetate or glucose from the column influent did not significantly affect herbicide biotransformation in the aerobic or nitratereducing reactors, at least for short periods. Temporary loss of the external electron acceptors (O₂, NO^- ₃or SO₄ ^2-) slowed transformation of both herbicides.     

Causes of Haze in the Columbia River Gorge

Abstract

Visibility impairment in the Columbia River Gorge National Scenic Area is an area of concern. A field study conducted from July 2003 to February 2005 was followed by data analysis and receptor modeling to better understand the temporal and spatial patterns of haze and the sources contributing to the haze in the Columbia River Gorge in the states of Washington and Oregon. The nephelometer light scattering and surface meteorological data at eight sites along the gorge showed five distinct wind patterns, each with its characteristic diurnal and spatial patterns in light scattering by particles (b_sp). In summer, winds were nearly always from west to east (upgorge) and showed decreasing b_sp with distance into the gorge and a pronounced effect of the Portland, OR, metropolitan area on haze, especially in the western portions of the gorge. Winter often had winds from the east with very high levels of b_sp, especially at the eastern gorge sites, with sources east of the gorge responsible for much of the haze. The major chemical components responsible for haze were organic carbon, sulfate, and nitrate. Positive matrix factorization (PMF) using chemically speciated Inter-agency Monitoring of Protected Visual Environments data indicated seven source factors in the western gorge and five factors in the eastern gorge. Organic mass is a large contributor to haze in the gorge in all seasons, with a peak in fall. The PMF analysis suggests that approximately half of the organic mass is biomass smoke, with mobile sources as the second largest contributor. PMF analysis showed nitrates (important in fall and winter) mainly attributed to a generic secondary nitrate factor, with the next largest contributor being oil combustion at Mt. Zion, WA and mobile sources at Wishram, WA. Sulfate is a significant contributor in all seasons, with peak sulfate concentrations in summer.     

Effect of PM2.5 chemical constituents on atmospheric visibility impairment

PM_2.5 sampling was conducted at a curbside location in Delhi city for summer and winter seasons, to evaluate the effect of PM_2.5 and its chemical components on the visibility impairment. The PM_2.5 concentrations were observed to be higher than the National Ambient Air Quality Standards (NAAQS), indicating poor air quality. The chemical constituents of PM_2.5 (the water-soluble ionic species SO₄^2-, NO₃^?, Cl^?, and NH₄⁺, and carbonaceous species: organic carbon, elemental carbon) were analyzed to study their impact on visibility impairment by reconstructing the light extinction coefficient, b_ext. The visibility was found to be negatively correlated with PM_2.5 and its components. The reconstructed b_ext showed that organic matter was the largest contributor to b_ext in both the seasons which may be attributed to combustion sources. In summer season, it was followed by elemental carbon and ammonium sulfate; however, in winter, major contributions were from ammonium nitrate and elemental carbon. Higher elemental carbon in both seasons may be attributed to traffic sources, while lower concentrations of nitrate during summer, may be attributed to volatility because of higher atmospheric temperatures.

Implications: The chemical constituents of PM_2.5 that majorly effect the visibility impairment are organic matter and elemental carbon, both of which are products of combustion processes. Secondary formations that lead to ammonium sulfate and ammonium nitrate production also impair the visibility.     

Chemical composition and mass closure of ambient coarse particles at traffic and urban-background sites in Thessaloniki,Greece

Concentrations and chemical composition of the coarse particle fraction (PM_c) were investigated at two urban sites in the city of Thessaloniki, Greece, through concurrent sampling of PM₁₀ and PM_2.5 during the warm and the cold months of the year. PM_c levels at the urban-traffic site (UT) were among the highest found in literature worldwide exhibiting higher values in the cold period. PM_c levels at the urban-background site (UB) were significantly lower exhibiting a reverse seasonal trend. Concentration levels of minerals and most trace metals were also higher at the UT site suggesting a stronger impact from traffic-related sources (road dust resuspension, brake and tire abrasion, road wear). According to the chemical mass closure obtained, minerals (oxides of Si, Al, Ca, Mg, Fe, Ti, and K) dominated the PM_c profile, regardless of the site and the period, with organic matter and secondary inorganic aerosols (mainly nitrate) also contributing considerably to the PM_c mass, particularly in the warm period. The influence of wind speed to dilution and/or resuspension of coarse particles was investigated. The source of origin of coarse particles was also investigated using surface wind data and atmospheric back-trajectory modeling. Finally, the contribution of resuspension to PM_c levels was estimated for air quality management perspectives.     

Estimating Gas Emissions from Multiple Sources Using a Backward Lagrangian Stochastic Model

Abstract

Manure storage tanks and animals in barns are important agricultural sources of methane. To examine the possibility of using an inverse dispersion technique based on a backward Lagrangian Stochastic (bLS) model to quantify methane (CH₄) emissions from multiple on-farm sources, a series of tests were carried out with four possible source configurations and three controlled area sources. The simulated configurations were: (C1) three spatially separate ground-level sources, (C2) three spatially separate sources with wind-flow disturbance, (C3) three adjacent ground-level sources to simulate a group of adjacent sources with different emission rates, and (C4) a configuration with a ground level and two elevated sources. For multiple ground-level sources without flow obstructions (C1 and C3), we can use the condition number (k, the ratio of the uncertainty in the calculated emission rate to the uncertainty in the predicted ratio of concentration to emission rate) to evaluate the applicability of this inverse dispersion technique and a preliminary threshold of k < 10 is recommended. For multiple sources with wind disturbance (C2) or an even more complex configuration including ground level and elevated sources (C4), a low k is not sufficient to provide reasonable discrete and total emission rates. The effect of flow obstructions can be neglected as long as the distance between the source and the measurement location is greater than approximately 10 times the height of the flow obstructions. This study shows that the bLS model has the potential to provide accurate discrete emission rates from multiple on-farm emissions of gases provided that certain conditions are met.     

The stable carbon isotope composition of PM2.5 and PM10 in Mexico City Metropolitan Area air

The sources and distribution of carbon in ambient suspended particles (PM_2.5 and PM₁₀) of Mexico City Metropolitan Area (MCMA) air were traced using stable carbon isotopes (¹³C/¹²C). Tested potential sources included rural and agricultural soils, gasoline and diesel, liquefied-petroleum gas, volcanic ash, and street dust. The complete combustion of LP gas, diesel and gasoline yielded the lightest δ¹³C values (?27 to ?29‰ vs. PDB), while street dust (PM₁₀) represented the isotopically heaviest endmember (?17‰). The δ¹³C values of rural soils from four geographically separated sites were similar (?20.7 ± 1.5‰). δ¹³C values of particles and soot from diesel and gasoline vehicle emissions and agricultural soils varied between ?23 and ?26‰. Ambient PM samples collected in November of 2000, and March and December of 2001 at three representative receptor sites of industrial, commercial and residential activities had a δ¹³C value centered around ?25.1‰ in both fractions, resulting from common carbon sources. The predominant carbon sources to MCMA atmospheric particles were hydrocarbon combustion (diesel and/or gasoline) and particles of geological origin. The significantly depleted δ¹³C values from the industrial site reflect the input of diesel combustion by mobile and point source emissions. Based on stable carbon isotope mass balance, the carbon contribution of geological sources at the commercial and residential sites was approximately 73% for the PM₁₀ fraction and 54% for PM_2.5. Although not measured in this study, biomass-burning emissions from nearby forests are an important carbon source characterized by isotopically lighter values (?29‰), and can become a significant contributor (67%) of particulate carbon to MCMA air under the prevalence of southwesterly winds. Alternative sources of these ¹³C-depleted particles, such as cooking fires and municipal waste incineration, need to be assessed. Results show that stable carbon isotope measurements are useful for distinguishing between some carbon sources in suspended particles to MCMA air, and that wind direction has an impact on the distribution of carbon sources in this basin.     

Wintertime Vertical Variations in Particulate Matter (PM) and Precursor Concentrations in the San Joaquin Valley during the California Regional Coarse PM/Fine PM Air Quality Study

Abstract

Air quality monitoring was conducted at a rural site with a tower in the middle of California’s San Joaquin Valley (SJV) and at elevated sites in the foothills and mountains surrounding the SJV for the California Regional PM₁₀/M_2.5 Air Quality Study. Measurements at the surface and on a tower at 90 m were collected in Angiola, CA, from ecember 2000 through February 2001 and included hourly black carbon (BC), particle counts from optical particle counters, nitric oxide, ozone, temperature, relative humidity, wind speed, and direction. Boundary site measurements were made primarily using 24-hr integrated particulate matter (PM) samples. These measurements were used to understand the vertical variations of PM and PM precursors, the effect of stratification in the winter on concentrations and chemistry aloft and at the surface, and the impact of aloft-versus-surface transport on PM concentrations. Vertical variations of concentrations differed among individual species. The stratification may be important to atmospheric chemistry processes, particularly nighttime nitrate formation aloft, because NO₂ appeared to be oxidized by ozone in the stratified aloft layer. Additionally, increases in accumulation-mode particle concentrations in the aloft layer during a fine PM (PM_2.5) episode corresponded with increases in aloft nitrate, demonstrating the likelihood of an aloft nighttime nitrate formation mechanism. Evidence of local transport at the surface and regional transport aloft was found; transport processes also varied among the species. The distribution of BC appeared to be regional, and BC was often uniformly mixed vertically. Overall, the combination of time-resolved tower and surface measurements provided important insight into PM stratification, formation, and transport.     

Air Quality Measurements from the Fresno Supersite

ABSTRACT

The Fresno Supersite intends to 1) evaluate non-routine monitoring methods, establishing their comparability with existing methods and their applicability to air quality planning, exposure assessment, and health effects studies; 2) provide a better understanding of aerosol characteristics, behavior, and sources to assist regulatory agencies in developing standards and strategies that protect public health; and 3) support studies that evaluate relationships between aerosol properties, co-factors, and observed health end-points. Supersite observables include in-situ, continuous, short-duration measurements of 1) PM_2.5, PM₁₀, and coarse (PM₁₀ minus PM_2.5) mass; 2) PM_2.5 SO₄ ^-2, NO₃ ^-, carbon, light absorption, and light extinction; 3) numbers of particles in discrete size bins ranging from 0.01 to ~10μm; 4) criteria pollutant gases (O₃, CO, NO_x); 5) reactive gases (NO₂, NO_y, HNO₃, peroxyacetyl nitrate [PAN], NH₃); and 6) single particle characterization by time-of-flight mass spectrometry. Field sampling and laboratory analysis are applied for gaseous and particulate organic compounds (light hydrocarbons, heavy hydrocarbons, carbonyls, polycyclic aromatic hydrocarbons [PAH], and other semi-volatiles), and PM_2.5 mass, elements, ions, and carbon. Observables common to other Supersites are 1) daily PM_2.5 24-hr average mass with Federal Reference Method (FRM) samplers; 2) continuous hourly and 5-min average PM_2.5 and PM₁₀ mass with beta attenuation monitors (BAM) and tapered element oscillating microbalances (TEOM); 3) PM_2.5 chemical specia-tion with a U.S. Environmental Protection Agency (EPA) speciation monitor and protocol; 4) coarse particle mass by dichotomous sampler and difference between PM₁₀ and PM_2.5 BAM and TEOM measurements; 5) coarse particle chemical composition; and 6) high sensitivity and time resolution scalar and vector wind speed, wind direction, temperature, relative humidity, barometric pressure, and solar radiation. The Fresno Supersite is coordinated with health and toxicological studies that will use these data in establishing relationships with asthma, other respiratory disease, and cardiovascular changes in human and animal subjects.     

Characterization of summertime coarse particulate matter in the Desert Southwest—Arizona,USA

A year-long study was conducted in Pinal County, AZ, to characterize coarse (2.5 – 10 μm aerodynamic diameter, AD) and fine (< 2.5 μm AD) particulate matter (PMc and PMf, respectively) to further understand spatial and temporal variations in ambient PM concentrations and composition in rural, arid environments. Measurements of PMc and PMf mass, ions, elements, and carbon concentrations at one-in-six day resolution were obtained at three sites within the region. Results from the summer of 2009 and specifically the local monsoon period are presented.

The summer monsoon season (July – September) and associated rain and/or high wind events, has historically had the largest number of PM₁₀ NAAQS exceedances within a year. Rain events served to clean the atmosphere, decreasing PMc concentrations resulting in a more uniform spatial gradient among the sites. The monsoon period also is characterized by high wind events, increasing PMc mass concentrations, possibly due to increased local wind-driven soil erosion or transport. Two PM₁₀ NAAQS exceedances at the urban monitoring site were explained by high wind events and can likely be excluded from PM₁₀ compliance calculations as exceptional events. At the more rural Cowtown site, PM₁₀ NAAQS exceedances were more frequent, likely due to the impact from local dust sources.

PM mass concentrations at the Cowtown site were typically higher than at the Pinal County Housing and Casa Grande sites. Crustal material was equal to 52-63% of the PMc mass concentration on average. High concentrations of phosphate and organic carbon found at the rural Cowtown were associated with local cattle feeding operations. A relatively high correlation between PMc and PMf (R²?=?0.63) indicated that the lower tail of the coarse particle fraction often impacts the fine particle fraction, increasing the PMf concentrations. Therefore, reductions in PMc sources will likely also reduce PMf concentrations, which also are near the value of the 24-hr PM_2.5 NAAQS.

Implications: In the desert southwest, summer monsoons are often associated with above average PM₁₀ (<10 μm AD) mass concentrations. Competing influences of monsoon rain and wind events showed that rain suppresses ambient concentrations while high wind increase them. In this region, the PMc fraction dominates PM₁₀ and crustal sources contribute 52-63% to local PMc mass concentrations on average. Cattle feedlot emissions are also an important source and a unique chemical signature was identified for this source. Observations suggest monsoon wind events alone cannot explain PM₁₀ NAAQS exceedances, thus requiring these values to remain in compliance calculations rather than being removed as exceptional wind events.     

固态碳源去除地下水硝酸盐的模拟实验

选取了5种研究较少的固体材料,棉花、丝瓜络、甘蔗渣、可降解餐盒、木屑作为去除地下水硝酸盐的外加碳源。在锥形瓶中进行反硝化对比实验,研究了不同固态碳源下NO3--N、NO2--N、NH4+-N及pH的变化情况,分析了NO3--N及总氮的去除率。研究结果表明,反硝化过程中pH呈升高趋势,在6.9～8.5范围内浮动。可降解餐盒和丝瓜络相对于其他的固态碳源来说,对NO3--N和总氮有较高的去除率,但丝瓜络的总氮去除率明显低于可降解餐盒。可降解餐盒的硝酸盐去除率达到98.28%,总氮去除率达到93.48%。可降解餐盒能够有效地去除地下水硝酸盐,达到以废治废的效果,是经济有效的最佳固态碳源。     

Contribution of Primary and Secondary Sources to Organic Aerosol and PM2.5 at SEARCH Network Sites

Abstract

Chemical tracer methods for determining contributions to primary organic aerosol (POA) are fairly well established, whereas similar techniques for secondary organic aerosol (SOA), inherently complicated by time-dependent atmospheric processes, are only beginning to be studied. Laboratory chamber experiments provide insights into the precursors of SOA, but field data must be used to test the approaches. This study investigates primary and secondary sources of organic carbon (OC) and determines their mass contribution to particulate matter 2.5 µm or less in aerodynamic diameter (PM_2.5) in Southeastern Aerosol Research and Characterization (SEARCH) network samples. Filter samples were taken during 20 24-hr periods between May and August 2005 at SEARCH sites in Atlanta, GA (JST); Birmingham, AL (BHM); Centerville, AL (CTR); and Pensacola, FL (PNS) and analyzed for organic tracers by gas chromatography-mass spectrometry. Contribution to primary OC was made using a chemical mass balance method and to secondary OC using a mass fraction method. Aerosol masses were reconstructed from the contributions of POA, SOA, elemental carbon, inorganic ions (sulfate [SO₄ ^2?], nitrate [NO₃ ^?], ammonium [NH₄ ⁺]), metals, and metal oxides and compared with the measured PM_2.5. From the analysis, OC contributions from seven primary sources and four secondary sources were determined. The major primary sources of carbon were from wood combustion, diesel and gasoline exhaust, and meat cooking; major secondary sources were from isoprene and monoterpenes with minor contributions from toluene and β-caryophyllene SOA. Mass concentrations at the four sites were determined using source-specific organic mass (OM)-to-OC ratios and gave values in the range of 12–42 µg m^?3. Reconstructed masses at three of the sites (JST, CTR, PNS) ranged from 87 to 91% of the measured PM_2.5 mass. The reconstructed mass at the BHM site exceeded the measured mass by approximately 25%. The difference between the reconstructed and measured PM_2.5 mass for nonindustrial areas is consistent with not including aerosol liquid water or other sources of organic aerosol.     

冬季沈阳市典型源排放PM_(10)浓度分布模拟分析

选取沈阳市7个典型的大气污染源2006年12月~2007年2月的PM10排放浓度资料,利用CALPUFF对PM10浓度月平均分布做模拟分析。模拟结果分析表明:冬季月平均PM10浓度分布的范围与风场、地形有直接的关系。地势平坦、风速大时,污染物扩散范围大,污染物浓度小;地势不平、风速小时,污染物扩散范围小,污染物浓度大。1月份是沈阳市冬季月平均大气污染最严重的月份,污染物分布主要集中在市区的北部、东部和南部地区,东部地区大气污染最为严重。     

Evaluation of low wind modeling approaches for two tall-stack databases

The performance of the AERMOD air dispersion model under low wind speed conditions, especially for applications with only one level of meteorological data and no direct turbulence measurements or vertical temperature gradient observations, is the focus of this study. The analysis documented in this paper addresses evaluations for low wind conditions involving tall stack releases for which multiple years of concurrent emissions, meteorological data, and monitoring data are available. AERMOD was tested on two field-study databases involving several SO₂ monitors and hourly emissions data that had sub-hourly meteorological data (e.g., 10-min averages) available using several technical options: default mode, with various low wind speed beta options, and using the available sub-hourly meteorological data. These field study databases included (1) Mercer County, a North Dakota database featuring five SO₂ monitors within 10 km of the Dakota Gasification Company’s plant and the Antelope Valley Station power plant in an area of both flat and elevated terrain, and (2) a flat-terrain setting database with four SO₂ monitors within 6 km of the Gibson Generating Station in southwest Indiana. Both sites featured regionally representative 10-m meteorological databases, with no significant terrain obstacles between the meteorological site and the emission sources. The low wind beta options show improvement in model performance helping to reduce some of the overprediction biases currently present in AERMOD when run with regulatory default options. The overall findings with the low wind speed testing on these tall stack field-study databases indicate that AERMOD low wind speed options have a minor effect for flat terrain locations, but can have a significant effect for elevated terrain locations. The performance of AERMOD using low wind speed options leads to improved consistency of meteorological conditions associated with the highest observed and predicted concentration events. The available sub-hourly modeling results using the Sub-Hourly AERMOD Run Procedure (SHARP) are relatively unbiased and show that this alternative approach should be seriously considered to address situations dominated by low-wind meander conditions.

Implications: AERMOD was evaluated with two tall stack databases (in North Dakota and Indiana) in areas of both flat and elevated terrain. AERMOD cases included the regulatory default mode, low wind speed beta options, and use of the Sub-Hourly AERMOD Run Procedure (SHARP). The low wind beta options show improvement in model performance (especially in higher terrain areas), helping to reduce some of the overprediction biases currently present in regulatory default AERMOD. The SHARP results are relatively unbiased and show that this approach should be seriously considered to address situations dominated by low-wind meander conditions.     

Feasibility of coupling a thermal/optical carbon analyzer to a quadrupole mass spectrometer for enhanced PM2.5 speciation

A thermal/optical carbon analyzer (TOA), normally used for quantification of organic carbon (OC) and elemental carbon (EC) in PM_2.5 (fine particulate matter) speciation networks, was adapted to direct thermally evolved gases to an electron impact quadrupole mass spectrometer (QMS), creating a TOA-QMS. This approach produces spectra similar to those obtained by the Aerodyne aerosol mass spectrometer (AMS), but the ratios of the mass to charge (m/z) signals differ and must be remeasured using laboratory-generated standards. Linear relationships are found between TOA-QMS signals and ammonium (NH₄⁺), nitrate (NO₃^?), and sulfate (SO₄^2-) standards. For ambient samples, however, positive deviations are found for SO₄^2-, compensated by negative deviations for NO₃^?, at higher concentrations. This indicates the utility of mixed-compound standards for calibration or separate calibration curves for low and high ion concentrations. The sum of the QMS signals across all m/z after removal of the NH₄⁺, NO₃^?, and SO₄^2- signals was highly correlated with the carbon content of oxalic acid (C?H?O?) standards. For ambient samples, the OC derived from the TOA-QMS method was the same as the OC derived from the standard IMPROVE_A TOA method. This method has the potential to reduce complexity and costs for speciation networks, especially for highly polluted urban areas such as those in Asia and Africa.

Implications: Ammonium, nitrate, and sulfate can be quantified by the same thermal evolution analysis applied to organic and elemental carbon. This holds the potential to replace multiple parallel filter samples and separate laboratory analyses with a single filter and a single analysis to account for a large portion of the PM_2.5 mass concentration.     

Estimation of particle resuspension source strength on a major London Road

Non-exhaust particles from road traffic arise from both abrasion sources and the resuspension of particles from the road surface. This paper reports a new combination of existing methods for indirect estimation of resuspension emission factors for Marylebone Road, London, a busy multi-lane highway in a street canyon. The method involves firstly estimating the total source strength of coarse particles (PM_2.5–10) arising from the road by calculating the roadside incremental concentration of coarse particles above the urban background. This is converted to a source strength by its ratio to NO_x whose source strength is estimated from the knowledge of the traffic mix and mean speed. This coarse particle source strength is assumed to represent the sum of resuspension emissions and the coarse particle component of abrasion emissions. Using information on the traffic mix and speed, the abrasion emissions have been calculated from the EMEP/CORINAIR emissions factor database, the result subtracted from the total coarse particle emissions in order to yield resuspension emissions, and combined with traffic count data to derive fleet-average emission factors. Using the fact that the traffic mix differs substantially between weekdays and weekends, separate average emission factors for light- and heavy-duty vehicles have been estimated. In addition to traffic mix, the influence of wind speed and the time elapsed since the last rainfall upon resuspension have been estimated. Wind speed was found to have by far the larger influence, although this was still secondary to the number of heavy-duty vehicles. Uncertainties arising from the choice of urban background site and poor data quality are discussed.     

C2–C5 Hydrocarbon measurements in the Netherlands 1981–1991

Measurements of C₂–C₅ hydrocarbons on an hourly basis at the TNO site in Delft from 1982 to 1984 and at Moerdijk over the period 1981–1991 are presented. In combination with meteorological data (wind direction and wind speed) the Delft and Moerdijk series are evaluated to identify source categories, annual variations, background concentrations and trends. The C₂–C₅ hydrocarbon concentrations at Delft and Moerdijk are determined mainly by emission characteristics and meteorological dispersion; the dominant sources are relatively nearby and atmospheric degradation is not of much importance. Under conditions of high wind speed the concentrations measured at Moerdijk in the marine sector are close to the Atlantic background concentrations in winter and somewhat above this in summer. The continental background concentrations are higher than the marine background concentrations by a factor of almost two. The annual variation of acetylene is more pronounced than that of the other hydrocarbons, most likely due to a different seasonal variation in acetylene emissions. The annual variation of propene is smoother, indicating stronger sources in summer than in winter. This feature of propene is observed in continental as well as in marine sectors. The observations show that at Moerdijk C₂–C₄ concentrations measured in Rijnmond sector have decreased considerably since the early 1980s, corresponding with changes in emissions in that area. Averaged over all wind directions the trend of all species is downward, but for acetylene the trend is significant at a 95% confidence interval. The acetylene concentrations show an annual downward trend of 3% during the 1980s, supporting other estimates of decreasing hydrocarbon emissions from traffic over this period at the same rate.     

The Southeastern Aerosol Research and Characterization Study,Part 3: Continuous Measurements of Fine Particulate Matter Mass and Composition

Abstract

Deployment of continuous analyzers in the Southeastern Aerosol Research and Characterization Study (SEARCH) network began in 1998 and continues today as new technologies are developed. Measurement of fine particulate matter (PM_2.5) mass is performed using a dried, 30 °C tapered element oscillating microbalance (TEOM). TEOM measurements are complemented by observations of light scattering by nephelometry. Measurements of major constituents include: (1) SO₄ ^2? via reduction to SO₂; (2) NH₄ ⁺ and NO₃ ^? via respective catalytic oxidation and reduction to NO, (3) black carbon (BC) by optical absorption, (4) total carbon by combustion to CO₂, and (5) organic carbon by difference between the latter two measurements. Several illustrative examples of continuous data from the SEARCH network are presented. A distinctive composite annual average diurnal pattern is observed for PM_2.5 mass, nitrate, and BC, likely indicating the influence of traffic-related emissions, growth, and break up of the boundary layer and formation of ammonium nitrate. Examination of PM_2.5 components indicates the need to better understand the continuous composition of the unmeasured “other” category, because it contributes a significant fraction to total mass during periods of high PM_2.5 loading. Selected episodes are presented to illustrate applications of SEARCH data. An SO₂ conversion rate of 0.2%/hr is derived from an observation of a plume from a coal-fired power plant during early spring, and the importance of local, rural sources of NH₃ to the formation of ammonium nitrate in particulate matter (PM) is demonstrated.     

Characteristics of the major chemical constituents of PM2.5 and smog events in Seoul,Korea in 2003 and 2004

One hundred ninety-five chemically speciated samples were collected from March 2003 to February 2005 in the Seoul Metropolitan area to investigate the characteristics of the major components in PM_2.5 and to characterize the chemical variations between smog and non-smog events. The annual average PM_2.5 concentration was 43 μg m⁻³ that is almost three times higher than the US NAAQS annual PM_2.5 standard of 15 μg m⁻³. During this sampling period, smog and yellow sand events were observed on 27 and 10 days, respectively. The PM_2.5 concentrations and its constituents during smog events were about two–three times higher than those during non-smog and yellow sand events. In particular, the mass fractions of secondary aerosols such as sulfate, nitrate, and ammonium during the smog events were higher than those of the other constituents. The mean concentration and mass fraction of secondary organic carbon (SOC) were highest during the winter smog events. Sulfate, nitrate and SOC that can have long residence times were important species during the smog events suggesting that regional scale sources rather than local sources were important. Five-day backward air trajectory analysis showed that the air parcels during smog events passed through the major industrial areas in China more often than those during non-smog events.