核桃壳对模拟废水中Cu~(2+)的吸附性能研究

采用核桃壳作为吸附剂,对模拟废水中的Cu2+进行吸附去除,考察了吸附剂粒径、水样初始pH、吸附剂用量、Cu2+初始浓度、吸附时间等因素对Cu2+吸附效果的影响,确定最佳吸附参数,并进行了吸附动力学和吸附等温线分析。结果表明:最佳吸附参数为核桃壳吸附剂粒径1.25~1.60mm、水样初始pH 5.0、吸附剂用量2.5g,Cu2+初始质量浓度20mg/L、吸附时间360min,在此条件下100mL水样在200r/min、25℃条件下吸附的Cu2+去除率达70%以上,吸附量约为0.702mg/g;本实验过程采用伪二级动力学方程的拟合更好,R2均在0.9以上,Cu2+吸附速率与其浓度的二次方成正比;Langmuir方程可以较好地描述核桃壳吸附剂对Cu2+的吸附过程,此吸附过程是单分子层的吸附。     

棘孢曲霉（Aspergillus aculeatus）对Pb^2＋和Cd^2＋的吸附特征

为了研究棘孢曲霉（Aspergillus aculeatus）对溶液中Pb^2＋和Cd^2＋吸附过程的特征，分别从动力学、热力学和吸附等温线三方面进行了实验，同时还研究了pH、温度、时间、重金属离子起始浓度和吸附剂用量对吸附过程的影响。等温吸附过程可以用Langmuir方程来描述。在实验设定条件下，棘孢曲霉对Pb^2＋和Cd^2＋最大吸附量分别为71．2mg／g和59．8mg／g；动力学实验数据很好的符合二级动力学方程，吸附达到平衡的时间为3h；热力学实验数据显示该吸附过程为自发的、吸热的过程。     

沸石负载淀粉对Pb2＋、Cu2＋和Ni2＋的吸附性能

将淀粉负载到沸石表面得到新型重金属离子复合吸附剂ZLS。分别从沸石与淀粉质量比、吸附温度、吸附时间、pH与重金属初始浓度不同方面考察了复合吸附剂ZLS吸附Pb^2＋、Cu^2＋、Ni^2＋的影响。实验结果表明：当沸石与淀粉质量比为10：1，pH为6，吸附温度在30℃时，复合型吸附剂ZLS对Pb^2＋、Cu^2＋和Ni^2＋3种重金属离子的吸附效果最好；吸附动力学研究发现，ZLS对Pb^2＋、Cu^2＋和Ni^2＋的吸附行为均符合准二级动力学以及颗粒内部扩散模型；等温吸附数据符合Fre-undlich模型，吸附状态属于多层吸附。     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能

以微硅粉为硅源，CTAB和PEG-6000为模板剂，合成MCM-41介孔分子筛。采用XRD、N2吸附-脱附曲线、FT—IR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌，并且以该样品为吸附剂，对含Cu2＋的溶液进行了静态吸附实验。结果表明，以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41，其比表面积为869．5m。／g，孔容为0．97cm3／g，平均孔径为3．3nm；溶液pH为5—6时，MCM-41对Cu2＋的去除效果最好；MCM-41对Cu3＋的最大吸附吸附容量36．3mg／g；MCM-41对Cu2＋的吸附性能符合Langmuir吸附方程的特征。动力学研究表明，该过程符合准二级动力学模型。     

香蕉皮吸附废水中铜、锌的研究

用香蕉皮作为吸附剂，对含有Cu^2＋、Zn^2＋的重金属废水进行了吸附研究。分别考察了pH值、溶液初始浓度、吸附剂量、吸附剂粒径以及吸附时间等因素对吸附的影响。结果表明，香蕉皮对Cu^2＋、Zn^2＋有较好的吸附效果。溶液的pH值在5左右，吸附时间为7h，香蕉皮对Cu^2＋、Zn^2＋的吸附率可达95％以上。     

聚（丙烯酸-co-丙烯酰胺）/膨润土/腐植酸钠三维网络凝胶吸附剂对Cd^2＋吸附性能研究

制备了一种聚（丙烯酸-co-丙烯酰胺）/膨润土/腐植酸钠三维网络凝胶吸附剂,重点考察了吸附剂对Cd2＋吸附的pH依赖性、吸附动力学和吸附等温线。结果表明,Cd^2＋溶液pH值对吸附容量有较大影响。在pH=8、吸附时间30 min、Cd^2＋溶液初始浓度0.02 mol/L和吸附剂用量0.10 g的条件下,吸附剂对Cd2＋的饱和吸附量可达294.7 mg/g。与膨润土相比,三维网络凝胶吸附剂具有更高的吸附容量和更快的吸附速率。     

电极-SBBR处理含铜有机污水

采用电极一SBBR系统去除Cu^2＋，考察了电流强度，IA竞争离子（阴离子SO4^2-、NO3^-、CL^-和阳离子Zn^2＋、Ph^2＋）、初始含Cu^2＋量及溶液pH值对除铜效除果的影响。结果表明，当电流强度为40mA时Cu^2＋去除率最高为98％。投加阴（SO4^2-、NO3^-、Cl^-）、阳（Zn^2＋、Pb^2＋）离子均会引起出水Cu^2＋浓度的增加，且Cl^-和Ph^2＋含量分别为45mg／L和30mg／L时对Cu^2＋去除的影响更为显著。进水Cu^2＋浓度为30mg／L时，Cu^2＋去除率最高为98．48％，当进水Cu^2＋≥70mg／L时，出水Cu^2＋浓度不能达标。酸性（pH4．0～4．5）与碱性（pH9．0～10．0）条件均不利于Cu^2＋的去除，且酸性条件的负面影响更显著．当pH为4．5～7．5时．Cu^2＋去除率最高为97．78％。     

胺化木质素对水中Cu（Ⅱ）、Cd（Ⅱ）的吸附

以胺化木质素作吸附剂对水中Cu2＋、Cd2＋的去除进行了研究，主要考察了吸附时间、溶液pH值、温度和金属离子初始浓度对吸附去除率的影响，并研究了其吸附等温线和动力学。结果表明，胺化木质素能有效去除水溶液中的Cu2＋、Cd2＋，且对Cd2＋的吸附能力大于Cu2＋吸附动力学符合准二级动力学方程，吸附等温线均可以很好地用Langmuir方程描述。     

生物质材料预处理餐饮废水

采用4种廉价的生物质材料（水葫芦、柚子皮、木屑、核桃壳）用于餐饮废水的预处理。通过静态烧杯实验，研究了各生物质材料预处理废水的效果及最佳处理条件。结果表明，生物质材料对废水中COD的去除率均在45％以上，油脂吸附量为4～16mg／g，最优吸附材料为水葫芦，COD去除率达65％，油脂吸附量为16mg／g；水葫芦和柚子皮的最佳处理条件为：粒径〈0．2mm，投加量为20g／L，废水pH为4，处理时间为2h，温度为20℃；木屑和核桃壳的最佳实验条件为：粒径〈0．2mm，投加量为28g／L，pH为2，处理时间为2．5h，温度为20℃。生物质对餐饮废水的预处理，为废水中大量有机物和废弃油脂的去除提供了新思路和途径。     

介孔纳米γ-Al2O3对稀土元素锎、铈的吸附性能

以介孔纳米γ-Al2O3为吸附材料，重点研究了吸附剂投加量、溶液pH、吸附时间及温度对介孔纳米γ-Al2O3吸附稀土元素镧、铈的影响。通过正交实验优选出介孔纳米γ-Al2O3对稀土元素镧铈吸附的最优参数，采用10mg／L的La^3＋、Ce^4＋标准溶液，选择投加量、pH、吸附时间为影响因素，进行3因素3水平的正交实验。通过正交实验与单因素实验综合分析表明最佳实验方案为：投加量为0．20g，pH为7，吸附时间为15min。在初始浓度为10～100mg／L时，介孑L纳米γ-Al2O3对La^3＋、Ce^4＋的吸附符合Langmuir等温吸附式。拟合得到的理论饱和吸附量分别为22．32mg／g和23．75mg／g。     

改性花生壳对Cd(Ⅱ)和Pb(Ⅱ)的吸附机理

以前期制得改性块状花生壳为对象,测定改性花生壳等电点,考察离子强度对改性花生壳吸附Cd2+和Pb2+的影响、吸附前后吸附质溶液pH变化情况及蒸馏水、NaCl、HNO3、柠檬酸和EDTA 5种解吸液对Cd2+和Pb2+的解吸效果,并通过X-射线光电子能谱仪和傅里叶变换红外光谱仪对吸附前后的改性花生壳进行表征,推测并证实了改性花生壳对Cd2+和Pb2+可能的吸附机理。结果表明,改性花生壳对Cd2+和Pb2+可能的吸附机理是:Cd2+是通过外层络合、离子交换和内层络合的联合作用被吸附的;Pb2+主要是与改性花生壳上的O、N等活性基团发生内层络合;此外,改性花生壳表面生成的二氧化锰对Cd2+和Pb2+的吸附也起到一定的作用。     

液/固体系中硅藻土对Pb2+和Cd2+的吸附机制

为了提高硅藻土在重金属废水处理上的应用水平,采用静态吸附实验考察了液/固体系中硅藻土对Pb2＋、Cd2＋的吸附影响因素、吸附等温线和吸附动力学属性。结果表明,随着投加量的减少,离子初始浓度的提高,pH值的增大,吸附作用时间的延长,硅藻土对Pb2＋、Cd2＋吸附量不断上升;硅藻土对Pb2＋、Cd2＋的等温吸附都符合Langmuir模型,硅藻土对Pb2＋、Cd2＋最大吸附量分别为10.428 mg/g和7.916 mg/g,硅藻土对Pb2＋具有更好的吸附能力;Pb2＋具有较低的水合自由能,更容易脱去水膜与硅藻土孔道内的活性基团发生吸附作用;双常数扩散方程可以很好地描述硅藻土对Pb2＋、Cd2＋的吸附动力学属性,硅藻土对Cd2＋有较快的吸附速率。     

改性玉米秸秆吸附Cu2+的动力学和热力学

本研究用ZnCl2作为活化剂,使用功率640 W的微波照射4 min的方法制备改性玉米秸秆。考察投加量、pH、吸附时间对吸附性能的影响,并对等温吸附特征、吸附动力学和热力学进行了系统研究。结果表明:投加量为0.2 g,pH为6,改性玉米秸秆对Cu2+具有很好的吸附效果,吸附在8 h后达到平衡。该吸附过程符合Langmuir及Freundlich等温吸附模型和准二级动力学方程,其反应的吉布斯自由能△G<0,为自发反应过程。     

磷酸活化-微波热解改性污泥对镉的吸附性能

以城市污水处理厂剩余污泥为原料,利用磷酸活化-微波热解制取改性污泥。以此污泥作为吸附剂,对含Cd2+废水进行了吸附实验研究。考察了溶液反应时间、Cd2+浓度、pH值和吸附剂用量对镉吸附去除效果的影响;利用等温吸附实验作出吸附等温线,并考察了改性污泥吸附剂吸附Cd2+的动力学方程。实验结果表明,改性污泥对Cd2+有良好的吸附性能,吸附最佳pH值为6.0,吸附较好地符合一级动力学吸附模型和Langmuir-Freundlich等温吸附方程,吸附为物理吸附,吸附反应发生12 h后达到吸附平衡。     

原位帽封材料对水体中Pb(Ⅱ)与Cd(Ⅱ)静态吸附

用无纺布包裹珊瑚和丙烯酸树脂制成帽封材料,将底泥中重金属离子原位固定的同时吸附水体中的重金属离子pb2和Cd2.通过红外光谱,电镜扫描和火焰原子吸收仪器来分析该帽封材料的吸附性能.通过改变pH值,吸附剂投放量来检测其吸附效果.结果表明,该帽封材料在pH等于5的时候,Cd2最大吸附量达到434.67 mg/g,pb2+最大吸附量达到524.27 mg/g.pH和吸附剂量保持不变,随着底物浓度增加吸附量也增加;电镜扫描图和红外光谱图表明,该材料能很好地吸附重金属离子.     

三乙二醇二甲基丙烯酸酯为交联剂制备的高吸水树脂对重金属的吸附

以前期工作中合成的树脂PAANa-TE为吸附剂进行重金属吸附测试,考察吸附剂用量、丙烯酸中和度、吸附时间、溶液pH、初始浓度和吸附温度对树脂吸附重金属离子Cu2+、Pb2+、Cr3+和Co2+性能的影响,用原子吸收分光光度计测定了树脂吸附Cu2+、Pb2+、Cr3+和Co2+后的残留浓度,树脂对4种金属离子的吸附容量分别为21.59、2.39、5.66和4.98 mmol/g,吸附容量大小为Cu2+Cr3+Co2+Pb2+,吸附速率顺序为Cr3+Pb2+Cu2+Co2+。结果表明,该树脂对高浓度重金属离子有较快速,高效率的吸附,吸附过程在100 min左右吸附容量达到最大,并用不同浓度的酸对吸附重金属离子的树脂进行脱附处理,脱附量很小,据此可考虑进一步对金属离子进行回收处理。且脱附率较低,因此,可对工业化和城市化进程所产生的各种化学形态的重金属水体污染物造成的生态环境和质量问题起到重要的改善作用。     

Kinetics and isotherm analysis of Tropaeoline 000 adsorption onto unsaturated polyester resin (UPR): a non-carbon adsorbent

The presence of dyes in water is undesirable due to the toxicological impact of their entrance into the food chain. Owing to the recalcitrant nature of dyes to biological oxidation, a tertiary treatment like adsorption is required. In the present study, unsaturated polyester resin (UPR) has been used as a sorbent in the treatment of dye-contaminated water. Different concentrations of Tropaeoline 000 containing water were treated with UPR. The preliminary investigations were carried out by batch adsorption to examine the effects of pH, adsorbate concentration, adsorbent dosage, contact time, and temperature. A plausible mechanism for the ongoing adsorption process and thermodynamic parameters have also been obtained from Langmuir and Freundlich adsorption isotherm models. Thermodynamic parameter showed that the sorption process of Tropaeoline 000 onto activated carbon (AC) and UPR were feasible, spontaneous, and endothermic under studied conditions. The estimated values for (ΔG) are ?10.48?×?10³ and ?6.098?×?10³ kJ mol^?1 over AC and UPR at 303 K (30 °C), indicating towards a spontaneous process. The adsorption process followed pseudo-first-order model. The mass transfer property of the sorption process was studied using Lagergren pseudo-first-order kinetic models. The values of % removal and k _ad for dye systems were calculated at different temperatures (303–323 K). The mechanism of the adsorption process was determined from the intraparticle diffusion model.     

Comparative study of adsorption of Pb(II) on native garlic peel and mercerized garlic peel

A comparative study using native garlic peel and mercerized garlic peel as adsorbents for the removal of Pb²⁺ has been proposed. Under the optimized pH, contact time, and adsorbent dosage, the adsorption capacity of garlic peel after mercerization was increased 2.1 times and up to 109.05 mg g^?1. The equilibrium sorption data for both garlic peels fitted well with Langmuir adsorption isotherm, and the adsorbent–adsorbate kinetics followed pseudo-second-order model. These both garlic peels were characterized by elemental analysis, Fourier transform infrared spectrometry (FT-IR), and scanning electron microscopy, and the results indicated that mercerized garlic peel offers more little pores acted as adsorption sites than native garlic peel and has lower polymerization and crystalline and more accessible functional hydroxyl groups, which resulted in higher adsorption capacity than native garlic peel. The FT-IR and X-ray photoelectron spectroscopy analyses of both garlic peels before and after loaded with Pb²⁺ further illustrated that lead was adsorbed on the through chelation between Pb²⁺ and O atom existed on the surface of garlic peels. These results described above showed that garlic peel after mercerization can be a more attractive adsorbent due to its faster sorption uptake and higher capacity.     

胺基树脂的合成及对水中重金属离子的吸附特征

研究了使用氯甲基化聚苯乙烯交联微球为前驱体与二乙烯三胺经回流反应合成胺基树脂及其对水中Cd2+和Ni2+的吸附特征。结果表明,胺基官能团成功地嫁接到树脂表面,胺基含量为5.6 mmol/g。胺基树脂对Cd2+和Ni2+的吸附等温线表明,温度的升高有利于吸附,且吸附等温线都符合Langmuir模型。pH值对吸附的影响较大,最佳吸附pH值范围为4~6。2种金属离子在胺基树脂上的吸附都符合准二级动力学方程。     

Removal of sulfamethoxazole from solution by raw and chemically treated walnut shells

Purpose

The sorption of sulfamethoxazole, a frequently detected pharmaceutical compound in the environment, onto walnut shells was evaluated.

Methods

The sorption proprieties of the raw sorbent were chemically modified and two additional samples were obtained, respectively HCl and NaOH treated. Scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and thermogravimetric (TG/DTG) techniques were applied to investigate the effect of the chemical treatments on the shell surface morphology and chemistry. Sorption experiments to investigate the pH effect on the process were carried out between pH?2 and 8.

Results

The chemical treatment did not substantially alter the structure of the sorbent (physical and textural characteristics) but modified the surface chemistry of the sorbent (acid?Cbase properties, point of zero charge??pH_pzc). The solution pH influences both the sorbent??s surface charge and sulfamethoxazole speciation. The best removal efficiencies were obtained for lower pH values where the neutral and cationic sulfamethoxazole forms are present in the solution. Langmuir and Freundlich isotherms were applied to the experimental adsorption data for sulfamethoxazole sorption at pH?2, 4, and 7 onto raw walnut shell. No statistical difference was found between the two models except for the pH?2 experimental data to which the Freundlich model fitted better.

Conclusion

Sorption of sulfamethoxazole was found to be highly pH dependent in the entire pH range studied and for both raw and treated sorbent.