Identification and source apportionment of polycyclic aromatic hydrocarbons in ambient air particulate matter of Riyadh, Saudi Arabia

In an effort to assess the occurrence and sources of polycyclic aromatic hydrocarbons (PAHs) in the ambient air of Riyadh, Saudi Arabia, PM₁₀ samples were collected during December 2010. Diagnostic PAH concentration ratios were used as a tool to identify and characterize the PAH sources. The results reflect high PM₁₀ and PAH concentrations (particulate matter (PM)?=?270–1,270 μg/m³). The corresponding average PAH concentrations were in the range of 18?±?8 to 1,003?±?597 ng/m³ and the total concentrations (total PAHs (TPAHs) of 17 compounds) varied from 1,383 to 13,470 ng/m³ with an average of 5,871?±?2,830 ng/m³. The detection and quantification limits were 1–3 and 1–10 ng/ml, respectively, with a recovery range of 42–80 %. The ratio of the sum of the concentrations of the nine major non-alkylated compounds to the total (CPAHs/TPAHs) was 0.87?±?0.10, and other ratios were determined to apportion the PM sources. The PAHs found are characteristic for emissions from traffic with diesel being a predominant source.     

Source apportionment of polycyclic aromatic hydrocarbons in surface sediments of the Bohai Sea, China

A total of 112 surface sediment samples covering virtually the entire Bohai Sea were analyzed for polycyclic aromatic hydrocarbons (PAHs), in order to provide the extensive information of recent occurrence levels, distribution, possible sources, and potential biological risk of these compounds in this area. Surface sediment samples were collected from the Bohai Sea using a stainless steel grab sampler. Sixteen PAHs were determined by a Finnigan TRACE DSQ gas chromatography/mass spectrometry. Diagnostic ratios, cluster analysis, and principal component analysis (PCA) with multivariate linear regression (MLR) were performed to identify and quantitatively apportion the major sources of sedimentary PAHs in the Bohai Sea. Concentrations of total PAHs in the Bohai Sea ranged widely from 97.2 to 300.7 ng/g (mean, 175.7?±?37.3 ng/g). High concentrations of PAHs were found in the vicinity of Luan River Estuary-Qinhuangdao Harbor, Cao River Estuary-Bohai Sea Center, and north of the Yellow River Estuary. The three-ring PAHs were most abundant, accounting for about 37?±?5 % of total PAHs. The four-ring and five-ring PAHs were the next dominant ones comprising approximately 29?±?7and 23?±?3 % of total PAHs, respectively. Concentrations of acenaphthylene, acenaphthene, and dibenz[a,h]anthracene are higher than Canadian interim marine sediment quality guideline values at most of the sites in the study area. Contamination levels of PAHs in the Bohai Sea were low in comparison with other coastal sediments in China and developed countries. The distribution pattern of PAHs and source identification implied that PAH contamination in the Bohai Sea mainly originates from petrogenic and pyrogenic sources. Further PCA/MLR analysis suggested that the contributions of spilled oil products (petrogenic), coal combustion, and traffic-related pollution were 39, 38, and 23 %, respectively. Pyrogenic sources (coal combustion and traffic-related pollution) contributed 61 % of anthropogenic PAHs to sediments, which indicates that energy consumption could be a dominant factor in PAH pollution in this area. Acenaphthylene, acenaphthene, and dibenz[a,h]anthracene are the three main species of PAHs with more ecotoxicological concern in the Bohai Sea.     

Biogenic polycyclic aromatic hydrocarbons in sediments of the San Joaquin River in California (USA), and current paradigms on their formation

Biogenic perylene and higher plant pentacyclic triterpenoid-derived alkylated and partially aromatized tetra- and pentacyclic derivatives of chrysene (3,4,7-trimethyl- and 3,3,7-trimethyl-1,2,3,4-tetrahydrochrysene, THC) and picene (1,2,9-trimethyl- and 2,2,9-trimethyl-1,2,3,4-tetrahydropicene, THP) were two- to four-fold more abundant than pyrogenic PAH in two sediment cores from the San Joaquin River in Northern California (USA). In a core from Venice Cut (VC), located in the river, PAH concentrations varied little downcore and the whole-core PAH concentration (biogenics?+?pyrogenics) was 250.6?±?73.7 ng g^?1 dw; biogenic PAH constituted 67?±?4 % of total PAH. THC were 26?±?9 % of total biogenic PAH, THP were 36?±?7 %, and perylene was 38?±?7 %. PAH distributions in a core from Franks Tract (FT), a former wetland that was converted to an agricultural tract in the late 1800s and flooded in 1938, were more variable. Surface sediments were dominated by pyrogenic PAH so that biogenic PAH were only ~30 % of total PAH. Deeper in the core, biogenic PAH constituted 60–93 % of total PAH; THC, THP and perylene were 31?±?28 %, 24?±?32 %, and 45?±?36 % of biogenic PAH. At 100–103 cm depth, THP constituted 80 % of biogenic PAH and at 120–123 cm perylene was 95 % of biogenic PAH. Current concepts related to precursors and transformation processes responsible for the diagenetic generation of perylene and triterpenoid-derived PAH are discussed. Distributions of biogenic PAH in VC and FT sediments suggest that they may not form diagenetically within these sediments but rather might be delivered pre-formed from the river’s watershed.     

Characterization and concentrations of polycyclic aromatic hydrocarbons in emissions from different heating systems in Damascus,Syria

Traffic has long been recognized as the major contributor to polycyclic aromatic hydrocarbon (PAH) emissions to the urban atmosphere. Stationary combustion sources, including residential space heating systems, are also a major contributor to PAH emissions. The aim of this study was to determine the profile and concentration of PAHs in stack flue gas emissions from different kinds of space heaters in order to increase the understanding of the scale of the PAH pollution problem caused by this source. This study set out to first assess the characteristics of PAHs and their corresponding benzo[a]pyrene equivalent emissions from a few types of domestic heaters and central heating systems to the urban atmosphere. The study, enabled for the first time, the characterization of PAHs in stationary combustion sources in the city of Damascus, Syria. Nine different types of heating systems were selected with respect to age, design, and type of fuel burned. The concentrations of 15 individual PAH compounds in the stack flue gas were determined in the extracts of the collected samples using high-performance liquid chromatography system (HPLC) equipped with ultraviolet–visible and fluorescence detectors. In general, older domestic wood stoves caused considerably higher PAH emissions than modern domestic heaters burning diesel oil. The average concentration of ΣPAH (sum of 15 compounds) in emissions from all types of studied heating systems ranged between 43?±?0.4 and 316?±?1.4 μg/m³. Values of total benzo[a]pyrene equivalent ranged between 0.61 and 15.41 μg/m³.     

Interaction of erythromycin ethylsuccinate and acetaminophen with protein fraction of extracellular polymeric substances (EPS) from various bacterial aggregates

Extracellular polymeric substances (EPS) are, along with microbial cells, the main components of the biological sludges used in wastewater treatment and natural biofilms. EPS play a major role in removing pollutants from water by means of sorption. The ability of soluble EPS (S-EPS) and bound EPS (B-EPS) derived from various bacterial aggregates (flocs, granules, biofilms) to bind at pH 7.0?±?0.1 to two pharmaceutical substances, acetaminophen (ACE) and erythromycin ethylsuccinate (ERY), has been investigated using the fluorescence quenching method. Two intense fluorescence peaks, A (Ex/Em range, 200–250/275–380 nm) and B (Ex/Em range, 260–320/275–360 nm), corresponding respectively to the aromatic protein region and soluble microbial by-product-like region, were identified in a three-dimensional excitation-emission matrix of EPS samples. The fluorescence peak, which corresponds to humic-like substances, was also identified though at low intensity. The ability of EPS to bind ACE was found to exceed that for ERY. The aromatic protein fraction of EPS displays a slightly higher affinity for drugs than that shown by the soluble microbial by-product-like fraction. The S-EPS and B-EPS present the same affinity for ACE and ERY. The effective quenching constants (log K) derived from the Stern–Volmer Equation equaled at peak A (with S-EPS): 3.7?±?0.2 to 4.0?±?0.1 for ACE and 2.1?±?0.3 to 2.7?±?0.1 for ERY. With B-EPS, these values were 3.9?±?0.1 to 4.0?±?0.1 for ACE and 2.0?±?0.2 to 2.6?±?0.1 for ERY. Our results suggest that the weaker EPS affinity for ERY than for ACE serves to partially explain why only about 50–80 % of ERY is removed from wastewater at the treatment plant. Moreover, this work demonstrates that EPS from natural river biofilms are able to bind drugs, which in turn may limit the mobility of drugs in natural waters.     

The behaviors and fate of polycyclic aromatic hydrocarbons (PAHs) in a coking wastewater treatment plant

The occurrence, behaviors and fate of 18 PAHs were investigated in a coking wastewater treatment plant in Songshan coking plant, located in Shaoguan, Guangdong Province of China. It was found that the target compounds occurred widely in raw coking wastewater, treated effluent, sludge and gas samples. In raw coking wastewater, high molecular weight (MW) PAHs were the dominant compounds, while 3-6 ring PAHs predominated in the final effluent. The dominant compounds in gas samples were phenathrene, fluoranthene and pyrene, while they were fluoranthene, pyrene, chrysene and benzo[k]fluoranthene for sludge. The process achieved over 97% removal for all the PAHs, 47-92% of eliminations of these target compounds in liquid phase were achieved in biological stage. Different behaviors of PAHs were observed in the primary tank, anaerobic tank, aerobic tank, hydrolytic tank and coagulation tank units, while heavier and lower ones were mainly removed in anaerobic tank and aerobic tanks, respectively. Regarding the fate of PAHs, calculated fractions of mass losses for low MW PAHs due to transformation and adsorption to sludge accounted for 15-50% and 24-49%, respectively, while the rest was less than 1%. For high MW PAHs, the mass losses were mainly due to adsorption to sludge and separation with tar (contributing 56-76% and 22-39%, respectively), and the removal through transformation was less.     

Accumulation pattern and distribution of polycyclic aromatic hydrocarbons (PAHs) in liver tissues of seven species of birds from Ahmedabad, India, during 2005–2007

Concentrations of polycyclic aromatic hydrocarbons (PAHs) were measured in liver tissues of seven species of birds collected from Ahmedabad, India during 2005–2007. All the samples collected were dead as victims of kite flying. Concentrations of ∑PAHs in livers of birds were ranged from 110?±?32.6 ng/g wet wt (1,078?±?320 lipid wt) in common myna Acridotheres tristis to 382?±?90.1 ng/g (2,388?±?563 lipid wt) in white-backed vulture. Statistically significant (p?<?0.05) differences in ∑PAHs were observed among species. However, year of collection and sex of birds did not show significant differences in concentrations of PAHs. The levels of ∑PAHs measured in the present study species were higher than the levels documented for a number of avian species and were lower than those reported to have deleterious effects on survival or reproduction of birds. Presence of PAH residues in birds of Ahmedabad city show the continuous input of PAHs through environmental exposure. Although no threat is posed by any of the hydrocarbons detected, continuous monitoring of breeding colonies of birds is recommended in unpolluted reference sites as well as polluted sites. It is also the first account of a comprehensive analysis of PAHs in various species of birds in India. Therefore, the values reported in this study can serve as baseline values for future research.     

Polycyclic aromatic hydrocarbons in wastewater, WWTPs effluents and in the recipient waters of Beijing, China

In this study, surface water samples from the Wenyu River and the North Canal, effluent from major wastewater treatment plants (WWTPs) in Beijing, and wastewater from open sewers that discharge directly into the river system were collected and analyzed for 16 priority USEPA polycyclic aromatic hydrocarbons (PAHs). Concentrations of these 16 PAHs ranged from 193 to 1790 ng/L in river surface waters, 245 to 404 ng/L in WWTP effluents, and 431 to 2860 ng/L in the wastewater from the small sewers. The WWTP effluent was the main contributor of dissolved PAHs to the river, while wastewater from the small sewers contributed both dissolved and suspended particulate matter-associated PAH to the river as indicated by the high dissolved organic carbon and suspended particulate matter contents in the wastewater. Although the flow from each open sewer was small, a PAH discharge as high as 44 kg/year could occur into the river from these types of sewers. This amount was equivalent to about 22 % of the PAH loads discharged into the North Canal downstream from Beijing, whereas the remainder was mainly released by the major WWTPs in Beijing.     

Occurrence and removal of polycyclic aromatic hydrocarbons and their derivatives in an ecological wastewater treatment plant in South China and effluent impact to the receiving river

Ecological wastewater treatment plant (EWWTP), a kind of emerging wastewater treatment plant (WWTP) in recent years, combined microbiology with botany which is efficient for the removal of nitrogen and organic matter, as well as deodorization. The occurrence and removal of micro-organic pollutants in EWWTPs were still not well known. Polycyclic aromatic hydrocarbons (PAHs) and their typical derivatives (SPAHs) including the oxygenated PAHs (OPAHs), chlorinated PAHs (ClPAHs), and methyl PAHs (MPAHs) were investigated in an EWWTP in Guangdong Province, China. The concentrations of the Σ6 OPAHs (114–384 ng/L) were higher than the Σ16 PAHs (92–250 ng/L), and much higher than the Σ4 MPAHs (13–64 ng/L) and Σ9 ClPAHs (2–3 ng/L) in the EWWTP and the effluent receiving river. The total removal efficiencies of the PAHs, OPAHs, MPAHs, and ClPAHs in the EWWTP (43?±?14%, 41?±?7%, 55?±?16%, and 18?±?4%) were lower than the traditional WWTPs, probably due to the lower concentration of the sludge in the ecological treatment. The advanced treatment process (microfiltration and UV disinfection treatment) contributed much less (0–20%) to the whole removal efficiency than the ecological treatment (80–100%). The effluent from the EWWTP slightly reduced the PAHs and SPAHs concentrations in the receiving river. The high concentrations of the PAHs and SPAHs in the receiving river were similar to the influent of the EWWTP, indicating that some untreated wastewater was directly discharged to the river, especially in the upstream.

     

Tracer-based source apportionment of polycyclic aromatic hydrocarbons in PM2.5 in Guangzhou, southern China, using positive matrix factorization (PMF)

From 28 November to 23 December 2009, 24-h?PM_2.5 samples were collected simultaneously at six sites in Guangzhou. Concentrations of 18 polycyclic aromatic hydrocarbons (PAHs) together with certain molecular tracers for vehicular emissions (i.e., hopanes and elemental carbon), coal combustion (i.e., picene), and biomass burning (i.e., levoglucosan) were determined. Positive matrix factorization (PMF) receptor model combined with tracer data was applied to explore the source contributions to PAHs. Three sources were identified by both inspecting the dominant tracer(s) in each factor and comparing source profiles derived from PMF with determined profiles in Guangzhou or in the Pearl River Delta region. The three sources identified were vehicular emissions (VE), biomass burning (BB), and coal combustion (CC), accounting for 11?±?2 %, 31?±?4 %, and 58?±?4 % of the total PAHs, respectively. CC replaced VE to become the most important source of PAHs in Guangzhou, reflecting the effective control of VE in recent years. The three sources had different contributions to PAHs with different ring sizes, with higher BB contributions (75?±?3 %) to four-ring PAHs such as pyrene and higher CC contributions (57?±?4 %) to six-ring PAHs such as benzo[ghi]perylene. Temporal variations of VE and CC contributions were probably caused by the change of weather conditions, while temporal variations of BB contributions were additionally influenced by the fluctuation of BB emissions. Source contributions also showed some spatial variations, probably due to the source emission variations near the sampling sites.     

Degradation of polycyclic aromatic hydrocarbons in a coking wastewater treatment plant residual by an O3/ultraviolet fluidized bed reactor

Coking wastewater treatment plant (CWWTP) represents a typical point source of polycyclic aromatic hydrocarbons (PAHs) to the water environment and threatens the safety of drinking water in downstream regions. To enhance the removal of residual PAHs from bio-treated coking wastewater, a pilot-scale O₃/ultraviolet (UV) fluidized bed reactor (O₃/UV FBR) was designed and different operating factors including UV irradiation intensity, pH, initial concentration, contact time, and hydraulic retention time (HRT) were investigated at an ozone level of 240 g h^?1 and 25?±?3 °C. A health risk evaluation and cost analysis were also carried out under the continuous-flow mode. As far as we know, this is the first time an O₃/UV FBR has been explored for PAHs treatment. The results indicated that between 41 and 75 % of 18 target PAHs were removed in O₃/UV FBR due to synergistic effects of UV irradiation. Both increased reaction time and increased pH were beneficial for the removal of PAHs. The degradation of the target PAHs within 8 h can be well fitted by the pseudo-first-order kinetics (R ²?>?0.920). The reaction rate was also positively correlated with the initial concentrations of PAHs. The health risk assessment showed that the total amount of carcinogenic substance exposure to surface water was reduced by 0.432 g day^?1. The economic analysis showed that the O₃/UV FBR was able to remove 18 target PAHs at a cost of US$0.34 m^?3. These results suggest that O₃/UV FBR is efficient in removing residuals from CWWTP, thus reducing the accumulation of persistent pollutant released to surface water.     

Characterisation of volatile organic compounds and polycyclic aromatic hydrocarbons in the ambient air of steelworks

Investigations have been undertaken at two integrated steelworks in the UK to characterise airborne organic micro-pollutants and to assess the contribution of iron ore sintering and coke making operations on the air quality. Concentrations of volatile organic compounds (VOCs), namely benzene, toluene and p-xylene, were measured continuously within the boundary of a coking plant using for the first time differential optical absorption spectrometry (DOAS) between 2004 and 2006. Concentrations were obtained along two monitoring paths surrounding the coke plant and the average benzene concentration measured along both paths over the campaign was 28 μg m^?3. Highest benzene concentrations were associated with winds downwind of the coke oven batteries. Concentrations of polycyclic aromatic hydrocarbons (PAHs) in ambient air were measured during 27 consecutive days in 2005 at three different locations on an integrated steelworks. PAH profiles were determined for each sampling point and compared to coke oven and sinter plant emission profiles showing an impact from the steelworks. The mean benzo [a] pyrene concentration determined in the immediate vicinity of the coke ovens downwind from the battery was 19 ng m^?3, whereas for the two other sites average benzo [a] pyrene concentrations were much lower (around 1 ng m^?3). Data were analysed using principal components analysis (PCA) and results showed that coke making and iron ore sintering were responsible for most of the variation in the PAH concentrations in the vicinity of the investigated plant.     

Remediation of polycyclic aromatic hydrocarbon and metal-contaminated soil by successive methyl-β-cyclodextrin-enhanced soil washing–microbial augmentation: a laboratory evaluation

Polycyclic aromatic hydrocarbon (PAH) and metal-polluted sites caused by abandoned coking plants are receiving wide attention. To address the associated environmental concerns, innovative remediation technologies are urgently needed. This study was initiated to investigate the feasibility of a cleanup strategy that employed an initial phase, using methyl-β-cyclodextrin (MCD) solution to enhance ex situ soil washing for extracting PAHs and metals simultaneously, followed by the addition of PAH-degrading bacteria (Paracoccus sp. strain HPD-2) and supplemental nutrients to treat the residual soil-bound PAHs. Elevated temperature (50 °C) in combination with ultrasonication (35 kHz, 30 min) at 100 g MCD L^?1 was effective in extracting PAHs and metals to assist soil washing; 93 % of total PAHs, 72 % of Cd, 78 % of Ni, 93 % of Zn, 84 % of Cr, and 68 % of Pb were removed from soil after three successive washing cycles. Treating the residual soil-bound PAHs for 20 weeks led to maximum biodegradation rates of 34, 45, 36, and 32 % of the remaining total PAHs, 3-ring PAHs, 4-ring PAHs, and 5(+6)-ring PAHs after washing procedure, respectively. Based on BIOLOG Ecoplate assay, the combined treatment at least partially restored microbiological functions in the contaminated soil. The ex situ cleanup strategy through MCD-enhanced soil washing followed by microbial augmentation can be effective in remediating PAH and metal-contaminated soil.     

Risk assessment of inhalation exposure to polycyclic aromatic hydrocarbons in school children

Polycyclic aromatic hydrocarbons (PAHs) associated with the inhalable fraction of particulate matter were determined for 1 year (2009–2010) at a school site located in proximity of industrial and heavy traffic roads in Delhi, India. PM₁₀ (aerodynamic diameter ≤10 μm) levels were ～11.6 times the World Health Organization standard. Vehicular (59.5 %) and coal combustion (40.5 %) sources accounted for the high levels of PAHs (range 38.1–217.3 ng m^?3) with four- and five-ring PAHs having ～80 % contribution. Total PAHs were dominated by carcinogenic species (～75 %) and B[a]P equivalent concentrations indicated highest exposure risks during winter. Extremely high daily inhalation exposure of PAHs was observed during winter (439.43 ng day^?1) followed by monsoon (232.59 ng day^?1) and summer (171.08 ng day^?1). Daily inhalation exposure of PAHs to school children during a day exhibited the trend school hours?>?commuting to school?>?resting period in all the seasons. Vehicular source contributions to daily PAH levels were significantly correlated (r?=?0.94, p?<?0.001) with the daily inhalation exposure level of school children. A conservative estimate of ～11 excess cancer cases in children during childhood due to inhalation exposure of PAHs has been made for Delhi.     

Migration of polycyclic aromatic hydrocarbons (PAHs) in urban treatment sludge to the air during PAH removal applications

In the present study, the amounts of polycylic aromatic hydrocarbons (PAHs) penetrating into air during PAH removal applications from the urban treatment sludge were investigated. The effects of the temperature, photocatalyst type, and dose on the PAH removal efficiencies and PAH evaporation were explained. The sludge samples were taken from an urban wastewater treatment plant located in the city of Bursa, with 585,000 equivalent population. The ultraviolet C (UV-C) light of 254 nm wavelength was used within the UV applications performed on a specially designed setup. Internal air of the setup was vacuumed through polyurethane foam (PUF) columns in order to collect the evaporated PAHs from the sludge during the PAH removal applications. All experiments were performed with three repetitions. The PAH concentrations were measured by gas chromatography–mass spectrometry (GC-MS). It was observed that the amounts of PAHs penetrating into the air were increased with increase of temperature, and more than 80% of PAHs migrated to the air consisted of 3-ring compounds during the UV and UV-diethylamine (DEA) experiments at 38 and 53 °C. It was determined that 40% decrease was ensured in Σ₁₂ (total of 12) PAH amounts with UV application and 13% of PAHs in sludge penetrated into the air. In the UV-TiO₂ applications, a maximum 80% of Σ₁₂ PAH removal was obtained by adding 0.5% TiO₂ of dry weight of sludge. The quantity of PAH penetrating into air did not exceed 15%. UV-TiO₂ applications ensured high levels of PAH removal in the sludge and also reduced the quantity of PAH penetrating into the air. Within the scope of the samples added with DEA, there was no increase in PAH removal efficiencies and the penetration of PAHs into air was not decreased. In light of these data, it was concluded that UV-TiO₂ application is the most suitable PAH removal alternative that restricts the convection of PAH pollution.

Implications: Polycyclic aromatic hydrocarbon (PAH) evaporation rates from sludge samples obtained from an urban wastewater treatment plant were investigated here for the first time by employing removal applications. TiO₂ and diethylamine were used as photocatalysts in this study. A special device was designed and successfully used in this study. Treatment sludge can be a significant source of PAHs for the atmosphere. The data highlight the need for removal of PAHs in treatment sludge via methods limiting their evaporation to the air. It was observed that UV-TiO₂ application was the most suitable PAH removal alternative that restricts the convection of PAH pollution.     

Environmental Progress and Problems: A Chemical Industry Perspective

From 1995 to 2004, in Genoa, Italy, daily concentrations of twelve polycyclic aromatic hydrocarbons (PAHs) were measured in particulate phase (PM10), around a coke oven plant in operation from the 1950s and closed in 2002. The study permitted to identify the coke oven as the main PAH source in Genoa, causing constant exceeding of benzo(a)pyrene (BaP) air quality target (1.0 ng/m3) in the urban area till 1,900 meters distance downwind the plant. For this reason the plant was closed. Distance and daily hours downwind the coke plant were the main sources of variability of toxic BaP equivalent (BaPeq) concentrations and equations that best fitted these variables were experimentally obtained. During full plant activity, annual average BaPeq concentrations, measured in the three sampling sites aligned downwind to the summer prevalent winds, were: 85 ng/m3 at 40 m (site 2, industrial area), 13.2 ng/m3 at 300 m (site 3, residential area) and 5.6 ng/m3 at 575 m (site 4, residential area).

Soon after the coke oven's closure (February 2002) BaPeq concentrations (annual average) measured in residential area, decreased drastically: 0.2 ng/m3 at site 3, 0.4 ng/m3 at site 4. Comparing 1998 and 2003 data, BaPeq concentrations decreased 97.6% in site 3 and 92.8% in site 4.

Samples collected at site 3, during the longest downwind conditions, provided a reliable PAH profile of fugitive coke oven emissions. This profile was significantly different from the PAH profile, contemporary found at site 5, near the traffic flow.

This study demonstrates that risk assessment based only on distance of residences from a coke plant can be heavily inaccurate and confirmed that seasonal variability of BaPeq concentrations and high variability of fugitive emissions of PAHs during coke oven activities require at least one year of frequent and constant monitoring (10-15 samples each month).

Implications: Around a coking plant, polycyclic aromatic hydrocarbons (PAHs), concentrations depend mainly on downwind hours and distance. Equations that best fit these variables were experimentally calculated. Fugitive emissions of an old coke oven did not comply with the threshold BAP air concentration proposed by the World Health Organization (WHO), up to 1,900 m distance. The study identified the PAH profile of fugitive emissions of a coke oven, statistically different from the profile of traffic emissions. During its activity, in the Genoa residential area, 575 m away from the plant, 92.8% of found PAHs was due to coke oven emission only.     

Risk Assessment of 26 Polycyclic Aromatic Hydrocarbon (PAH) Compounds in Parkıng Garages

The aim of this study was to determine the level of 26 polycyclic aromatic hydrocarbons (PAHs) at parking garages and to provide the necessary annual information based on occupational inhalation exposure and non-occupational inhalation exposure, which carry risks for the environment. For this purpose, 22 samples were collected continuously from both gas and particulates phase PAHs from two parking garages at Konya City Center, Turkey. The exposure-based risk of these samples was evaluated using concentrations of the carcinogenic PAH compounds. None of the 26 PAHs measured had values exceeding the recommended exposure limits (RELs) standard values for inhalation rate recommended by the World Health Organization (WHO). Exposure levels of gas and particulate PAHs for the occupational group and the public (children and adults who spend time in shopping centers) were found to be 0.07–28.24 μgm^?3 and 0.05–5.753 μgm^?3, respectively, representing levels two to four times higher than those at the control site. Maximum daily inhalation of B[a]Py was estimated at 1.33 ngd^?1 for exposure of the public and as 274 ngd^?1 for the occupational group. It is believed that traffic makes a substantial contribution to the PAH profile, which had relatively high concentrations of naphthalene (Napth) and coronene (Coro). Highly carcinogenic dibenzo(a,l)pyrene (B[al]Pyre) was found in the ambient air at two parking garages. Napth and phenanthrene (Phen) were the main compounds found in nearly all the tested samples. In this study, benzo[e]pyrene (B[e]Py) was used as a reference for PAHs because its concentration is stable and does not change seasonally. Considering the importance of these compounds in relation to human health, the aim of this work was to characterize and quantify the more toxic PAHs in parking garages. Conducting PAH sampling and their chemical analysis is very costly and labor intensive. This study produced data that can be a powerful tool for environmental forensics.     

Polycyclic aromatic hydrocarbon contamination in an urban area assessed by Quercus ilex leaves and soil

We investigated the PAH contamination of Naples urban area, densely populated and with high traffic flow, by analyses of environmental matrices: soil and Quercus ilex leaves. Being some PAHs demonstrated to have hazardous effects on human health, the accumulation of carcinogenic and toxic PAHs (expressed as B(a)Peq) was evaluated in the leaves and soil. The main sources of the PAHs were discriminated by the diagnostic ratios in the two matrices. The urban area appeared heavily contaminated by PAHs, showing in soil and leaves total PAH concentrations also fivefold higher than those from the remote area. The soil mainly accumulated heavy PAHs, whereas leaves the lightest ones. Median values of carcinogenic PAH concentrations were higher in soil (440 ng g^?1 d.w.) and leaves (340 ng g^?1 d.w.) from the urban than the remote area (60 and 70 ng g^?1 d.w., respectively, for soil and leaves). Also, median B(a)Peq concentrations were higher both in soil and leaves from the urban (137 and 63 ng g^?1 d.w., respectively) than those from the remote area (19 and 49 ng g^?1 d.w., respectively). Different from the soils, the diagnostic ratios found for the leaves discerned PAH sources in the remote and urban areas, highlighting a great contribution of vehicular traffic emission as main PAH source in the urban area.     

Organic micropollutants’ distribution within sludge organic matter fractions explains their dynamic during sewage sludge anaerobic digestion followed by composting

The simultaneous fate of organic matter and 4 endocrine disruptors (3 polycyclic aromatic hydrocarbons (PAHs) (fluoranthene, benzo(b)fluoranthene, and benzo(a)pyrene) and nonylphenols (NP)) was studied during the anaerobic digestion followed by composting of sludge at lab-scale. Sludge organic matter was characterized, thanks to chemical fractionation and 3D fluorescence deciphering its accessibility and biodegradability. Total chemical oxygen demand (COD) removal was 41% and 56% during anaerobic digestion and composting, respectively. 3D fluorescence highlighted the quality changes of organic matter. During continuous anaerobic digestion, organic micropollutants’ removal was 22?±?14%, 6?±?5%, 18?±?9%, and 0% for fluoranthene, benzo(b)fluoranthene, benzo(a)pyrene, and nonylphenols, respectively. Discontinuous composting allowed to go further on the organic micropollutants’ removal as 34?±?8%, 31?±?20%, 38?±?10%, and 52?±?6% of fluoranthene, benzo(b)fluoranthene, benzo(a)pyrene, and nonylphenols were dissipated, respectively. Moreover, the accessibility of PAH and NP expressed by their presence in the various sludge organic matter fractions and its evolution during both treatments was linked to both the quality evolution of the organic matter and the physicochemical properties of the PAH and NP; the presence in most accessible fractions explained the amount of PAH and NP dissipated.

     

Dietary risk evaluation for 28 polycyclic aromatic hydrocarbons (PAHs) in tea preparations made of teas available on the Polish retail market

The aim of this work was to assess dietary risk resulting from consumption of polycyclic aromatic hydrocarbons (PAHs) with tea infusions. To this end, levels of 28 PAHs in black, green, red and white teas available on the Polish retail market have been assessed. Profiles and correlation between concentrations of individual PAHs have been identified. A model study on transfer of PAHs from tea leaves into tea preparations has been conducted. Relatively high concentrations of 28 evaluated PAHs have been found in 58 tested samples of black, green, red and white teas sampled on the Polish retail market. Total concentration ∑28PAH ranged from 57 to 696 µg kg^?1 with mean 258 µg kg^?1 (dry tea leaves). The most mature tea leaves fermented to a small degree contained relatively the highest PAH levels among all four tested tea types. Relatively low PAH transfer rates into tea infusions and limited volumes of the consumed tea keep the risks associated with PAH dietary intake at a safely low level.

The worst-case scenario dietary intake values were 7.62/0.82/0.097 ng kg^?1 b.w. day^?1 (estimated on the basis of the maximum found concentrations 696/113/23 µg kg^?1 and maximum observed transfer rates 24/16/9%) for ∑28PAH/∑PAH4/B[a]P, respectively. MOE values calculated using the above worst case estimates exceeded 700,000 and 400,000 (BMDL₁₀ 0.07 and 0.34 mg kg^?1 b.w. day^?1) for B[a]P and PAH4, respectively. Both B[a]P and PAH4 concentrations may be used as indicators of total PAH concentration in tea leaves; PAH4 slightly better fits low molecular weight PAHs. Several correlations between various PAHs/groups of PAHs have been identified, the strongest one (R² = 0.92) between PAH4 and EU PAH 15+1.