Biodegradability of the X-ray contrast compound diatrizoic acid, identification of aerobic degradation products and effects against sewage sludge micro-organisms

Pharmaceuticals and contrast media have been detected in hospital effluents, sewage treatment plants, surface water, and ground water. Only little is known about their elimination during sewage treatment and effects of possible biotransformation products against bacteria. The modified Zahn-Wellens test (ZWT, OECD 302 B) and a test simulating biological sewage treatment (modified OECD 303 A test) were used to assess the biodegradability of the widely used ionic iodinated contrast agent diatrizoic acid (diatrizoate). Effects against sewage sludge bacteria were studied in the two test systems by monitoring the biomarkers quinones, polyamines, phospholipids and adenosine triphosphate. Diatrizoate was biotransformed into 2,4,6-triiodo-3,5-diamino-benzoic acid in the ZWT. 2,4,6-Triiodo-3,5-diamino-benzoic acid was stable under the test conditions of the ZWT. Diatrizoate was not eliminated in the OECD 303 A simulation test. It was not adsorbed by the sewage sludge. No effects of the test compound or its aerobic transformation products against the bacteria present in the sewage sludge were detected using phospholipids, quinones, polyamines, and adenosine triphosphate as biomarkers.     

Assessment of aliphatic-aromatic copolyester biodegradable mulch films. Part II: laboratory simulated conditions

In a previous paper, we demonstrated that the main mechanism of degradation of poly(butylene adipate-co-terephthalate) (PBAT) biodegradable mulch films when exposed to field conditions was crosslinking due to the photodegradation from solar radiation. The aim of this work was to determine the effect of crosslinking on the biodegradability of PBAT samples. PBAT films were subjected to UV photodegradation in laboratory simulated conditions to investigate the effects of crosslinking and other major changes in the structure and mechanical properties of the films. Crosslinking caused the films to become more brittle and produced a reduction of the tensile strength and percent elongation. Besides the crosslinking degradation mechanism, chain scission also occurred in the samples. After 45d of biodegradation test, the non-crosslinked PBAT sample reached 60% of mineralization. However, the percent mineralization was reduced when samples were crosslinked. The percent mineralization of samples with 10%, 30%, 50%, and 70% gel content was 36%, 43%, 21%, and 24%, respectively. Our results indicate that crosslinking is a key process underlying the degradation of the PBAT film and did affect the biodegradability of the films, since the samples with greater amount of gel content generally showed less percent mineralization in the biodegradation tests.     

Ultimate biodegradation and elimination of antibiotics in inherent tests

The biodegradation and elimination of antibiotics in municipal wastewater treatment plants is of particular concern because sewage is the main exposure route for antibiotics used in human medicine. The inherent biodegradability of 17 antibiotics was determined in a combined test design based on the Zahn-Wellens test (OECD 302 B, 1992) and the CO2-evolution test (OECD 301 B, 1992). CO2 Evolution test (Modified Sturm test). OECD Guideline for the Testing of Chemicals, Paris). Only benzylpenicillin sodium salt (Penicillin G) proved to be ultimately biodegradable, reaching ThCO2 degradation extents of 78-87%. Among the others, only amoxicillin, imipenem and nystatin showed certain ultimate biodegradation in few of the parallel flasks and can be regarded as partially biodegradable with formation of stable metabolites. The DOC-elimination of tetracycline-HCl showed a typical degradation curve starting with 18% and reaching the plateau phase at 80% after 21 days. Nevertheless, the CO2-evolution measured in parallel did not support the data, indicating that the time needed for reaching the adsorption equilibrium was underestimated. Several other antibiotics showed considerable DOC-elimination in the inherent test while only minor incidences of ultimate biodegradation were observed. The combination of CO2-evolution and DOC-elimination is a suitable instrument for assessing the behaviour of chemicals within one test. It enables one to assess both inherent ultimate biodegradability and DOC-elimination by sorption. The applicability of the test is limited to substances with a moderate toxicity.     

Benzyl-penicillin (Penicillin G) transformation in aqueous solution at low temperature under controlled laboratory conditions

Antibiotics are released into the environment in a variety of ways: via wastewater effluent as a result of incomplete metabolism in the body after use in human therapy, as runoff after use in agriculture, through improper disposal by private households or hospitals or through insufficient removal by water treatment plants. Unlike in most European countries, in Arctic regions effluents are not suitably treated prior to their release into the aquatic environment. Also, many of the scattered human settlements in remote regions of the Arctic do not possess sewage treatment facilities and pharmaceutical residues therefore enter the aqueous environment untreated. Only limited data are available on the biodegradation of antibiotics under Arctic conditions. However, such information is needed to estimate the potential harm of antibiotics for the environment. Pen-G is used in this study since it is a widely prescribed antibiotic compound whose environmental properties have not yet been investigated in detail. Thus, for a very first assessment, the OECD approved biodegradation Zahn-Wellens test (ZWT, OECD 302 B) was used to study biodegradation and non-biotic elimination of the antibiotic Benzyl-penicillin (Pen-G) at different temperatures (5°C, 12.5°C and 20°C). The testing period was extended from the OECD standard of 28-42d. In addition to dissolved organic carbon (DOC), Pen-G levels and major transformation products were recorded continuously by LC-ion-trap-MS/MS. DOC monitoring revealed considerable temperature dependence for the degradation process of Pen-G. DOC loss was slowest at 5°C and considerably faster at 12.5°C and 20°C. In the initial step of degradation it was found that Pen-G was hydrolyzed. This hydrolyzed Pen-G was subsequently further degraded by decarboxylation, the result of which was 2-(5,5-dimethyl-1,3-thiazolidin-2-yl)-2-(2-phenylacetamido)acetic acid. Furthermore, direct elimination of 2-phenyl-acetaldehyde from the hydrolyzed and decarboxylated Pen-G also led to the formation of 2-[amino(carboxy)methyl]-5,5-dimethyl-1,3-thiazolidone-4-carboxylic acid. Since biodegradation slows down considerably at a low temperature, the resulting transformation products had considerably longer residence times at 5°C compared to higher temperature conditions within the 42-d experiment. The results presented here clearly demonstrate that a risk assessment for pharmaceuticals present in low ambient temperature environments (i.e. the Arctic) cannot be based on test results obtained under standard laboratory conditions (i.e. 20°C ambient temperatures).     

Measuring the biodegradability of nonylphenol ether carboxylates, octylphenol ether carboxylates, and nonylphenol

We examined the biodegradability of several metabolites of C8- and C9-alkylphenol ethoxylates, including nonylphenoxyacetic acid (NPEC1), nonylphenoxyethoxyacetic acid (NPEC2), octylphenoxyacetic acid (OPEC1), octylphenoxyethoxyacetic acid (OPEC2), and nonylphenol (NP). Using OECD method 301B (modified Sturm method), OPEC1 and OPEC2 are readily biodegradable: both compounds exceeded 60% of theoretical CO2 formation (ThCO2) by day 28, and required less than 10 days to go from 10% to 60% ThCO2. Also using method 301B, NPEC1 and NPEC2 exceeded 60% ThCO2 at day 28, but did not meet the 10 day window. Using OECD method 301F, the manometric respirometry method that measures oxygen consumption, approximately 62% of NP was biodegraded in 28 days, but required more than 10 days to go from 10% to 60% biodegradation. While the validity of the "10-day window" is currently being debated within OECD, the data show that the common metabolites of C8- and C9-APEs are rapidly degraded in the test systems used, which strongly suggests that they would not accumulate or persist in the environment.     

Assessment of degradation of 18 antibiotics in the Closed Bottle Test

Large quantities of antibiotics are used in health care. After administration, they are discharged into the effluent and reach sewage treatment plants (STPs); if they are not degraded, they will eventually enter the environment. Antibiotics can affect bacteria in the environment and thus disturb natural elemental cycles. For this reason, it is necessary to take a closer look at the fate and effects of these substances in the environment. The biodegradability of 18 clinically important antibiotics and their effects on environmental bacteria was studied using the Closed Bottle Test (CBT) (OECD 301 D 1992). In addition, a toxicity control was performed in the CBT and the colony forming units (CFUs) were monitored. Disappearance of some of the 18 antibiotics was monitored by HPLC (high performance liquid chromatography) analysis. The antibiotics were used in two concentrations: (a) according to OECD 301 D in the mg/l-range and (b) on the basis of calculated concentrations in the influent of STPs in the microg/l-range. None of the 18 antibiotics were readily biodegradable. The HPLC analysis showed that some substances were partially or even completely disappeared by a non-biotic mechanism. In the case of some antibiotics, partial biological removal took place in test vessels containing readily biodegradable sodium acetate and the test compound. However, in the toxicity control, toxicity had not been eliminated.     

Biodegradation potential of ofloxacin and its resulting transformation products during photolytic and photocatalytic treatment

The release of pharmaceuticals in the environment, as parent compounds, metabolites and transformation products, and the consequent risks posed to living organisms due to the unintended exposure of the latter to these chemicals are nowadays of increasing scientific concern. The development of advanced oxidation processes able to degrade these substances is in the core of the current research objectives, the main target being the removal of these compounds from wastewaters. Often the focus is on the removal of the parent compound only. However, these processes can form transformation products. Knowledge on the risk related to such transformation products is scarce. Among others, knowledge on their toxic effects and their biodegradability is of importance not only when they are present in the environment but also for the assessment of the advanced oxidation processes’ efficiency applied for their degradation. Photolytic (UV irradiation) and photocatalytic treatment (UV irradiation in the presence of TiO₂) of the fluoroquinolone ofloxacin were applied, and the biodegradability of the formed products was investigated using the Closed Bottle test (OECD 301 D). Various transformation products, formed both during the photo(cata)lytic treatment and the Closed Bottle test, were identified using chromatographic analysis with an ultra high-performance liquid chromatography–tandem mass spectrometry (UPLC–MS/MS) system. The transformation products formed during the phototreatments were found to be non-readily biodegradable as the biodegradation percentages were close to zero. The persistence of the various photo(cata)lytic transformation products during the Closed Bottle test may be attributed to the fluorine present in all the transformation products formed. The transformation products identified suggest that two transformation routes were present: decarboxylation and opening of the piperazinyl ring. Interestingly, it was observed that in the presence of a readily biodegradable carbon source (sodium acetate), the biodegradation percentage increased drastically for some of the photolytically treated samples. This was not the case for the photocatalytically treated samples, in which also mineralization of the parent compound was achieved faster. Further research is needed, however, in order to increase the understanding of the conditions that may lead to less potent and persistent substances during the application of such engineered or natural processes.     

Incomplete aerobic degradation of the antidiabetic drug Metformin and identification of the bacterial dead-end transformation product Guanylurea

Active pharmaceutical ingredients as well as personal care products are detected in increasing prevalence in different environmental compartments such as surface water, groundwater and soil. Still little is known about the environmental fate of these substances. The type II antidiabetic drug Metformin has already been detected in different surface waters worldwide, but concentrations were significantly lower than the corresponding predicted environmental concentration (PEC). In human and mammal metabolism so far no metabolites of Metformin have been identified, so the expected environmental concentrations should be very high.To assess the aerobic biodegradability of Metformin and the possible formation of degradation products, three Organisation of Economic Cooperation and Development (OECD) test series were performed in the present study.In the Closed Bottle test (OECD 301 D), a screening test that simulates the conditions of an environmental surface water compartment, Metformin was classified as not readily biodegradable (no biodegradation). In the Manometric Respiratory test (OEDC 301 F) working with high bacterial density, Metformin was biodegraded in one of three test bottles to 48.7% and in the toxicity control bottle to 57.5%. In the Zahn-Wellens test (OECD 302 B) using activated sludge, Metformin was biodegraded in both test vessels to an extent of 51.3% and 49.9%, respectively.Analysis of test samples by high performance liquid chromatography coupled to multiple stage mass spectrometry (HPLC-MS(n)) showed in the tests vessels were biodegradation was observed full elimination of Metformin and revealed Guanylurea (Amidinourea, Dicyandiamidine) as single and stable aerobic bacterial degradation product. In another Manometric Respiratory test Guanylurea showed no more transformation. Photodegradation of Guanylurea was also negative.A first screening in one of the greatest sewage treatment plant in southern Germany found Metformin with high concentrations (56.8 μg L⁻¹) in the influent (PEC = 79.8 μg L⁻¹), but effluent concentration was much lower (0.76 μg L⁻¹) whereas Guanylurea was detected in a low influent and high effluent concentration (1.86 μg L⁻¹). These data support the experimental findings in the OECD tests and analytical results of other studies, that Metformin under aerobic conditions can bacterially be degraded to the stable dead-end transformation product Guanylurea.     

紫外光照射与生物降解耦合用于PCBs降解的研究

介绍了PCBs紫外光降解的机理及研究进展 ,讨论了影响PCBs光降解的主要因素 ,即环上的氯原子数目、取代位置及所处的微环境均显著地影响PCBs的光降解速率。简述了PCBs生物降解的研究进展 ,重点概述了好氧降解、厌氧降解及好氧厌氧协同作用的机理及特点。最后 ,讨论了PCBs生物降解和光降解的互补性 ,介绍了最近的研究进展 ,指出光降解和生物降解耦合将加快PCBs的移走速率 ,提出了PCBs污染土壤原位修复需要进一步解决的问题。     

Application of the headspace CO2 method (ISO 14 593) to the assessment of the ultimate biodegradability of surfactants: results of a calibration exercise

In the recent review of the control of marketing surfactants used in detergents, the EU decided to increase the severity of the testing procedure by using the criterion of ultimate biodegradability (mineralization) rather than primary biodegradation (removal of the parent molecule) to ensure that possible harmful organic metabolites do not reach the environment. The relatively new ISO headspace CO2 test, considered to be an improvement on the OECD 301B (Sturm CO2) test was chosen. The method was subjected to a ring test by 11 laboratories using one of each of four classes of surfactants plus a poorly degradable reference surfactant; all laboratories satisfactorily applied the method. The necessary addition of silica gel to the medium containing the cationic surfactant, known as a class to be more inhibitory than other classes, was confirmed as a technique for avoiding inhibition of the inoculum. The biodegradability of the surfactants was in general agreement with results reported in the literature and the often reported variable values of % inorganic carbon (IC) produced of the theoretical was found. The anionic and cationic surfactants were readily biodegradable (%IC > 60), the non-ionic surfactant was well below the pass value, while the amphoteric was borderline. The IC production by the blank controls, one of the validity criteria, was about 0.3 mg C/100 ml test medium, equivalent to 3 mg C/l, as recommended in the ISO text. Mild conditions of pre-exposure of the inoculum to the test surfactant did not produce consistent worthwhile effects on either the percentage biodegradation or on its variability.     

Benzyl-penicillin (Penicillin G) transformation in aqueous solution at low temperature under controlled laboratory conditions

Antibiotics are released into the environment in a variety of ways: via wastewater effluent as a result of incomplete metabolism in the body after use in human therapy, as runoff after use in agriculture, through improper disposal by private households or hospitals or through insufficient removal by water treatment plants. Unlike in most European countries, in Arctic regions effluents are not suitably treated prior to their release into the aquatic environment. Also, many of the scattered human settlements in remote regions of the Arctic do not possess sewage treatment facilities and pharmaceutical residues therefore enter the aqueous environment untreated.Only limited data are available on the biodegradation of antibiotics under Arctic conditions. However, such information is needed to estimate the potential harm of antibiotics for the environment. Pen-G is used in this study since it is a widely prescribed antibiotic compound whose environmental properties have not yet been investigated in detail. Thus, for a very first assessment, the OECD approved biodegradation Zahn–Wellens test (ZWT, OECD 302 B) was used to study biodegradation and non-biotic elimination of the antibiotic Benzyl-penicillin (Pen-G) at different temperatures (5 °C, 12.5 °C and 20 °C). The testing period was extended from the OECD standard of 28–42 d. In addition to dissolved organic carbon (DOC), Pen-G levels and major transformation products were recorded continuously by LC-ion-trap-MS/MS. DOC monitoring revealed considerable temperature dependence for the degradation process of Pen-G. DOC loss was slowest at 5 °C and considerably faster at 12.5 °C and 20 °C. In the initial step of degradation it was found that Pen-G was hydrolyzed. This hydrolyzed Pen-G was subsequently further degraded by decarboxylation, the result of which was 2-(5,5-dimethyl-1,3-thiazolidin-2-yl)-2-(2-phenylacetamido)acetic acid. Furthermore, direct elimination of 2-phenyl-acetaldehyde from the hydrolyzed and decarboxylated Pen-G also led to the formation of 2-[amino(carboxy)methyl]-5,5-dimethyl-1,3-thiazolidone-4-carboxylic acid. Since biodegradation slows down considerably at a low temperature, the resulting transformation products had considerably longer residence times at 5 °C compared to higher temperature conditions within the 42-d experiment. The results presented here clearly demonstrate that a risk assessment for pharmaceuticals present in low ambient temperature environments (i.e. the Arctic) cannot be based on test results obtained under standard laboratory conditions (i.e. 20 °C ambient temperatures).     

Biological and photochemical degradation rates of diethylenetriaminepentaacetic acid (DTPA) in the presence and absence of Fe(III)

The environmental fate of ethylenediaminetetraacetic acid (EDTA) has been extensively studied, while much less is known about the environmental behaviour of diethylenetriaminepentaacetic acid (DTPA). In this study, it was confirmed that DTPA is persistent toward biodegradation. The biodegradability of DTPA was investigated in the absence and in the presence of Fe(III) by using CO2 evolution test and Manometric respirometry test. The CO2 evolution and oxygen uptake of iron-free (DTPA was added as free acid) and Fe(III)DTPA were less than in inoculum blank. Possible inhibitor effect was analysed by testing biodegradation of sodium benzoate with and without iron-free or Fe(III)DTPA in the Manometric respirometry test. Only slight inhibition was observed when DTPA was added as free acid. Photodegradation of iron-free DTPA and Fe(III)-DTPA complex was studied by using sunlight and UV radiation at the range 315-400 nm emitted by black light lamps. The results indicate that DTPA added as free acid degrades photochemically in humic lake water. Fe(III)DTPA was shown to be very photolabile in humic lake water in the summer; the photochemical half-life was below one hour. Photodegradation products were identified by the mass spectrometric technique (GC-MS). It was shown that photodegradation of Fe(III)DTPA does not result in total mineralization of the compound. Diethylenetriaminetetraacetic acid, diethylenetriaminetriacetic acid, ethylenediaminetriacetic acid, N,N'- and/or N,N-ethylenediaminediacetic acid, iminodiacetate, ethylenediaminemonoacetic acid and glycine were identified as photodegradation products of Fe(III)DTPA. Based on these observations, we propose a photodegradation pathway for Fe(III)DTPA.     

Biodegradability of some antibiotics, elimination of the genotoxicity and affection of wastewater bacteria in a simple test

Most antibiotics and their metabolites are excreted by humans after administration and therefore reach the municipal sewage with the excretions. Only little is known about their biodegradability in aquatic environments. It was recognised that genotoxic substances may represent a health hazard to humans but also may affect organisms in the environment. Therefore, the biodegradability of some clinically important antibiotic drugs (ciprofloxacin, ofloxacin, metronidazole) and hereby the elimination of their genotoxicity was investigated as the first step of an environmental risk assessment using the Closed Bottle test (CBT) (OECD 301 D) and the SOS chromotest. Additionally, to assess toxicity of the antibiotics tested against aquatic bacteria (i) a growth inhibition test (GIT) with Pseudomonas putida was conducted, (ii) a toxicity control was used in the CBT and (iii) the colony forming units (CFUs) were monitored in the test vessels. Worst case concentrations of the antibiotics in hospital effluents were estimated and compared with minimum inhibitory concentrations for susceptible pathogenic bacteria and with the genotoxic potency in the SOS chromotest. Both the concentrations calculated for hospital effluents and the adverse effects in bacteria were in the same order of magnitude. None of the test compounds were biodegraded. The genotoxicity was not eliminated.     

Biodegradation of US premanufacture notice chemicals in OECD tests

Biodegradation testing of commercial chemicals other than pesticides is generally performed using test guidelines of the Organization for Economic Cooperation and Development (OECD). We used test data submitted with US Premanufacture Notifications (PMNs) received from 1995 through 2005 to study performance of OECD biodegradation tests, as well as the overall testing strategy and guidance. Among the findings are that (1) ready biodegradation (RB) tests gave fairly consistent results relative to the pass/fail outcome, but not necessarily percent degradation; (2) the Zahn-Wellens test worked well in providing a quick measure of sorption potential, but aside from this, provided little useful information for the investigated chemicals beyond what was already available from RB tests; (3) the SCAS test sometimes gives lower % removal than continuous-feed simulation tests like OECD 303A; and (4) OECD 306 (marine biodegradation test) appeared less conservative than ordinary RB tests. Overall, the PMN data lend support to new OECD guidance that endorses the primary role of RB tests, but emphasizes simulation rather than inherent biodegradation tests as the next step.     

Photocatalytic degradation of an organophosphorus pesticide phosalone in aqueous suspensions of titanium dioxide

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO2 particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. The half-life (DT50) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K=0.0532 min(-1)). The half-life time of photomineralization in the concentration range of 7.5-20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

Mixtures of quaternary ammonium compounds and anionic organic compounds in the aquatic environment: Elimination and biodegradability in the closed bottle test monitored by LC-MS/MS

Quaternary ammonium compounds (QACs) are widely used as disinfectants, detergents and fabric softeners. Anionic detergents are one of the most widely used chemical substances. QACs and anionic surfactants can form ionic pairs. In the present study we investigated the biodegradability of QACs in the presence of different anionic surfactants. The biodegradability of three QACs, namely benzalkonium chloride (BAC), didecyldimethylammonium chloride (DDMAC) and ethacridine lactate (EL), when applied as single substances and in combination with anionic surfactants such as benzene sulfonic acid (BSA), LAS, naphthalene sulfonic acid (NSA) and sodium dodecylsulfonate (SDS) was studied applying the closed bottle test (CBT) [OECD 301D, 1992. Guidelines for Testing of Chemicals. Closed bottle test. Organisation of Economic Cooperation and Development, Paris] at a ratio of 1:1 (mol:mol). Biodegradation was monitored by measuring oxygen concentration in the test vessels with an oxygen electrode in accordance with international standard methods [ISO 5414, 1990. Water quality - determination of dissolved oxygen. In: German Standard Methods for the Examination of Water, Wastewater and Sludge. VCH Verlagsgesellschaft, Weinheim, New York, Basel Cambridge]. Primary elimination of the QACs and of LAS was monitored by LC-MS/MS. There was little biodegradability of the QACs as either single compounds or in the presence of organic counter ions. The biodegradability of the organic counter ions was lower in the presence of QACs as compared to the single substances. Primary elimination of the QACs by sorption took place.     

PCB removal from contaminated dredged material

The purpose of this study was to evaluate the feasibility of decontaminating PCB contaminated sediment using land treatment technology. Five glass aquariums were set up to test the disappearance of polychlorinated biphenyls (PCBs) in dredged sediment under laboratory conditions that simulated photodegradation, biological transformation, and volatilization in dredged material confined disposal facilities (CDFs). A 40% decline in PCB concentration was achieved over a period of 5 months. Analysis of the variance in the data showed that periodic tilling produced a tangible effect on the disappearance of PCBs. However, the process or processes responsible for PCB disappearance could not be determined. PCB disappearance from the sediment was most likely caused by a combination of photolysis, volatilization, and biodegradation mechanisms rather than by any single process.     

Nitrate-induced photodegradation of atenolol in aqueous solution: kinetics, toxicity and degradation pathways

The extensive utilization of β-blockers worldwide led to frequent detection in natural water. In this study the photolysis behavior of atenolol (ATL) and toxicity of its photodegradation products were investigated in the presence of nitrate ions. The results showed that ATL photodegradation followed pseudo-first-order kinetics upon simulated solar irradiation. The photodegradation was found to be dependent on nitrate concentration and increasing the nitrate from 0.5 mM L⁻¹ to 10 mM L⁻¹ led to the enhancement of rate constant from 0.00101 min⁻¹ to 0.00716 min⁻¹. Hydroxyl radical was determined to play a key role in the photolysis process by using isopropanol as molecular probe. Increasing the solution pH from 4.8 to 10.4, the photodegradation rate slightly decreased from 0.00246 min⁻¹ to 0.00195 min⁻¹, probably due to pH-dependent effect of nitrate-induced OH formation. Bicarbonate decreased the photodegradation of ATL in the presence of nitrate ions mainly through pH effect, while humic substance inhibited the photodegradation via both attenuating light and competing radicals. Upon irradiation for 240 min, only 10% reduction of total organic carbon (TOC) can be achieved in spite of 72% transformation rate of ATL, implying a majority of ATL transformed into intermediate products rather than complete mineralization. The main photoproducts of ATL were identified by using solid phase extraction-liquid chromatography-mass spectrometry (SPE-LC-MS) techniques and possible nitrate-induced photodegradation pathways were proposed. The toxicity of the phototransformation products was evaluated using aquatic species Daphnia magna, and the results revealed that photodegradation was an effective mechanism for ATL toxicity reduction in natural waters.     

Photocatalytic Degradation of an Organophosphorus Pesticide Phosalone in Aqueous Suspensions of Titanium Dioxide

Abstract

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO₂ particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. The half-life (DT₅₀) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K = 0.0532 min^?1). The half-life time of photomineralization in the concentration range of 7.5–20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

Aerobic biodegradability of the calcium channel antagonist verapamil and identification of a microbial dead-end transformation product studied by LC-MS/MS

In recent years pharmaceuticals and personal care products have been detected in increasing concentrations in hospital effluents, sewage treatment plants (STP) as well as in different environmental compartments such as surface water, groundwater and soil. Little is known about the elimination of these substances during sewage treatment or about the formation of potential metabolites in the environment caused by bacterial biotransformation. To assess the biodegradability of the popular cardiovascular drug verapamil and the possible formation of potential microbial degradation products, two tests from the OECD series were used in the present study: the widely used Closed Bottle test (OECD 301 D) and the modified Zahn-Wellens test (OECD 302 B). In the Closed Bottle test, a screening test that simulates the conditions of an environmental surface water compartment, no biological degradation was observed for verapamil at concentrations of 2.33mgl(-1). In the Zahn-Wellens test, a test for inherent biodegradability which allows evaluation of aerobic degradation at high bacterial density, only a partial biological degradation was found. Analysis of test samples by high performance liquid chromatography coupled to multiple stage mass spectrometry (HPLC-MSn) revealed 2-(3,4-dimethoxyphenyl)-2-isopropyl-5-(methylamino)pentane nitrile, already known as D617 (Knoll nomenclature), a metabolite of mammalian metabolism, which is the major degradation product and dead-end transformation product of aerobic degradation of verapamil.