粉煤灰对水溶液中磷的吸附性能及机理

以粉煤灰为吸附剂去除溶液中的磷,考察了其吸附除P动力学特征、热力学特征以及溶液初始pH和粉煤灰投加量对吸附除P效果的影响,并对其吸附除P机理做了初步探讨。结果表明,在给定实验条件下,粉煤灰对P具有较好的去除效果,随着初始P浓度从10 mg/L升高到80 mg/L,平衡吸附量为0.46～2.44 mg P/g粉煤灰,吸附效率从92.2%降低至61.1%;对不同浓度的含P溶液,粉煤灰最适用量为0.6～1.5 g粉煤灰/mg P;相同反应条件下,当温度由25℃升高到45℃时,P初始吸附速率提高了3倍;粉煤灰对P的吸附过程能够较好地拟合Langmuir、Freundlich及D-R吸附等温模型,相关系数均在0.98以上。通过对吸附饱和的粉煤灰进行解析实验发现,初始P浓度较低(<50 mg/L)时,以化学吸附为主,而在初始P浓度较高(>80 mg/L)时,则以物理吸附为主。     

粉煤灰协同微波-Fenton氧化法处理活性艳蓝KN-R染料废水

以粉煤灰联合微波-Fenton氧化工艺处理活性艳蓝KN-R生产废水,考察了粉煤灰投加量及吸附时间对处理效果的影响,并通过正交实验对微波-Fenton工艺参数进行了优化。实验结果表明,粉煤灰絮凝吸附与微波-Fenton氧化具有协同效应;在粉煤灰投加量为40 g/L,搅拌吸附时间为20 min,滤液pH值为4,Fe2＋和H2O2投加量分别为3.6 mmol/L和0.15 mol/L,微波功率为200 W,辐射反应时间为4 min的优化条件下,染料废水的处理效果最好,COD和色度的去除率分别达到90.90%和99.98%。     

改性粉煤灰处理低浓度含磷废水的研究

以酸改性粉煤灰为吸附剂,处理低质量浓度(1 mg/L左右)磷酸盐溶液,探讨了改性剂的种类、改性剂用量、吸附剂用量、反应时间、pH以及温度对除磷效果的影响.结果表明:(1)经过酸改性后粉煤灰的磷去除率显著提高,而且硫酸改性粉煤灰的除磷效果更好,磷去除率最高可达97.68％.(2)最佳条件:选择硫酸用量为5 mL/g进行改性,硫酸改性粉煤灰投加量为2.0g,反应时间为60 min,pH为7.2～10.8,温度为25℃(即室温).(3)改性粉煤灰对磷的吸附更符合Freundlich吸附等温模型,既有物理吸附,也有化学吸附,并以Ca、Mg氧化物与磷形成磷的沉淀物为主.     

Phosphate removal from digested sludge supernatant using modified fly ash

The removal of phosphate in digested sludge supernatant by modified coal fly ash was investigated in this study. Modification of the fly ash by the addition of sulfuric acid could significantly enhance its immobilization ability. The experimental results also showed that adsorption of phosphate by the modified fly ash was rapid with the removal percentage of phosphate reaching an equilibrium of 98.62% in less than 5 minutes. The optimum pH for phosphate removal was 9 and the removal percentage increased with increasing adsorbent dosage. The effect of temperature on phosphate removal efficiency was not significant from 20 to 40 degrees C. X-ray diffraction and scanning electron microscope analyses showed that phosphate formed an amorphous precipitate with water-soluble calcium, aluminum, and iron ions in the modified fly ash.     

Removal of PCBs from wastewater using fly ash

Liquids and sludges containing polychlorinated biphenyls (PCBs) can be treated to concentrate the PCBs in a solid residue. The latter can then be handled to destroy the PCBs. A study on sorption kinetics of PCBs on fly ash was conducted in controlled batch systems. TCB and HeCB are removed at 25 degrees C by adsorption on fly ash up to 97% at pH 7, with an adsorbent dose of 5 g/l. An examination of the thermodynamic parameters shows that the adsorption of TCB and HeCB by fly ash is a process occurring spontaneously at ambient conditions. Activation energies for the sorption process ranged between 5.6 and 49.1 kJ/mol. It was observed that the rate at which TCB and HeCB are adsorbed onto fly ash showed a diffusion limitation. The uptake rate of TCB and HeCB increases with increasing initial concentration and gradually tends to a constant value. A decrease in the adsorption of TCB and HeCB was observed when interfering ions and other PCB congeners were present. Changing the pH in the aqueous solution from 2 to 10 had no effect on the adsorption process. Overall, fly ash can be used for an efficient removal of PCBs from several aqueous solutions.     

Continuous CO2 capture and MSWI fly ash stabilization, utilizing novel dynamic equipment

Novel dynamic equipment with gas in and out continuously was developed to study the capture capacity of CO₂. Municipal solid waste incineration (MSWI) fly ash has a high capture rate of CO₂ in CO₂-rich gas. Fly ash can sequester pure CO₂ rapidly, and its capacity is 16.3 g CO₂/100 g fly ash with no water added and 21.4 g CO₂/100 g fly ash with 20% water added. For simulated incineration gas containing 12% CO₂, the capture rate decreased and the capacity was 13.2 g CO₂/100 g fly ash with no water added and 18.5 g CO₂/100 g fly ash with 20% water added. After accelerated carbonation, the C and O contents increased, indicating CO₂ capture in the fly ash; CO₂ combines with Ca(OH)₂ to form CaCO₃, which increased the CaCO₃ content from 12.5 to 54.3%. The leaching of Pb markedly decreased from 24.48 to 0.111 mg/L.     

Effect of fly ash characteristics on the removal of Cu(II) from aqueous solution

Fly ash is a particulate substance containing metal oxides, carbon and other microelements. In this study, fly ashes with different quantities of carbon and minerals prepared by a thermal process in the laboratory were used as adsorbents to investigate the contribution of precipitation and adsorption to the removal of aqueous Cu(II). Experimental results showed that the specific surface area of fly ash increased linearly with the quantity of carbon. The specific surface areas of the carbon and mineral fraction were 60 m2/g and 0.68 m2/g, respectively. The specific adsorption capacities of carbon ranged from 2.2 to 2.8 mg Cu/g carbon, while those for mineral were only about 0.63 to approximately 0.81 mg Cu/g mineral. Consequently, the carbon fraction in fly ash was important in the removal of Cu(II) at pH 5. However, Cu(II) removal owing to precipitation increases with a decreasing carbon fraction and the contribution of copper precipitation was estimated to be approximately 23% to approximately 82% of total removal, depending on the carbon fraction of fly ash.     

Preliminary study on removing Cs+/Sr2+ by activated porous calcium silicate—A by-product from high-alumina fly ash recycling industry

¹³⁷Cs⁺/⁹⁰Sr²⁺-containing radioactive wastewater is one of the most important problems that the world has been facing with. A by-product, activated porous calcium silicate, is generated at high levels by the pre-desiliconizing and soda-lime-sintering processes for producing Al₂O₃ from high-alumina fly ash. In order to examine if this by-product could be used as an absorbent for removal of ¹³⁷Cs⁺/⁹⁰Sr²⁺ from radioactive wastewater, various parameters, such as pH, adsorbent dose, contact time, and initial concentration, were discussed. Results indicated that the equilibrium reached in about 2 hr. Activated porous calcium silicate was highly pH sensitive and able to remove Cs⁺/Sr²⁺ in a near-neutral environment. The adsorption equilibrium was best described by Freundlich isotherm equations, and the adsorption of Cs⁺/Sr²⁺ was a physical process. The adsorption kinetic data could be better fitted by the pseudo-second-order model, and the adsorption was controlled by multidiffusion. Current study showed that activated porous calcium silicate has a good adsorption of Cs⁺/Sr²⁺ for their removal. However, other characteristics, such as selectivity because of coexisting cations, elution and regeneration, thermal stability, and acid resistance, should be discussed carefully before using it in an actual field.

Implications:Removing ¹³⁷Cs⁺/⁹⁰Sr²⁺ from radioactive wastewater is one of the tough issues that has been attracting more and more attention world widely, which is the same as fly ash. For recycling high-alumina fly ash, in which Al is extracted to produce Al₂O₃, a huge amount of activated porous calcium silicate is generated year by year. In this paper, this by-product was successfully used as an absorbent to remove ¹³⁷Cs⁺/⁹⁰Sr²⁺ from radioactive wastewater for the first time. Factors that affect the absorbability and the mechanisms were discussed in details, providing a possible choice for disposal of ¹³⁷Cs⁺/⁹⁰Sr²⁺-containing radioactive wastewater.     

壳聚糖联合碱改性粉煤灰对重金属离子的吸附特性

采用浸渍法将壳聚糖负载在经NaOH改性的粉煤灰上，制备了联合改性的粉煤灰。随粉煤灰上壳聚糖负载量的增加，粉煤灰对Pb²⁺和Cd²⁺的吸附率均提高。当负载壳聚糖的质量分数为8%，吸附温度为30℃，吸附时间为120 min时，粉煤灰对Pb²⁺的吸附率最高（为98.9%），对Cd²⁺的吸附率也最高（为91.5%）。其吸附行为符合Freundlich等温吸附模型，但表现为2个线性区。粉煤灰负载壳聚糖的改性机理是粉煤灰与带正电荷的壳聚糖的化学键合作用。     

Adsorption kinetics and modeling of H2S by treated waste oil fly ash

Waste oil fly ash (OFA) collected from disposal of power generation plants was treated by physicochemical activation technique to improve the surface properties of OFA. This synthesized material was further used for potential hydrogen sulfide (H₂S) adsorption from synthetic natural gas. The raw OFA was basically modified with a mixture of acids (20% nitric acid [HNO₃] and 80% phosphoric acid [H₃PO₄]), and it was further treated with 2 M potassium hydroxide (KOH) to enhance the surface affinity as well as surface area of synthesized activated carbon. Correspondingly, it enhanced the adsorption of H₂S. Crystallinity, surface morphology, and pore volume distribution of prepared activated carbon were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) analyses. Fourier transform infrared (FTIR) study was also performed to identify the functional groups during different synthesis stages of modified activated carbon. The Langmuir, Freundlich, Sips, and dual-site Langmuir (DSL) models were used to study the kinetic and breakthrough behavior of H₂S adsorption over alkali-modified activated carbon. Modeling results of isotherms indicated that OFA has dual sites with high and low affinity for H₂S adsorption. The Clark model, Thomas model, and Yoon-Nelson model were used to examine the effects of flow rate and inlet concentration on the adsorption of H₂S. Maximum uptake capacity of 8.5 mg/g was achieved at 100 ppm inlet concentration and flow rate of 0.2 L/min.

Implications: Utilization of worthless oil fly ash from power plant is important not only for cleaning the environment but also for solid waste minimization. This research scope is to eradicate one pollutant by using another pollutant (waste ash) as a raw material. Chemical functionalization of synthesized activated carbon from oil fly ash would lead to attachment of functional groups of basic nature to attract the acidic H₂S. Such type of treatment can enhance the uptake capacity of sorbent several times.     

Effect of fly ash on sorption behavior of metribuzin in agricultural soils

This investigation was undertaken to determine the effect of two different fly ashes [Kota and Inderprastha (IP)] amendment on the sorption behavior of metribuzin in three Indian soil types. The IP fly ash was very effective in increasing the metribuzin sorption in the soils. The sorption with IP amendment was increased by 15–92%, whereas with the Kota fly ash an increase in sorption by 13–38% was noted. The adsorption isotherms fitted very well to the Freundlich adsorption equation and, in general, slope (1/n) values less then unity were observed. Although both the fly ashes significantly decreased metribuzin desorption, the IP fly ash was comparatively more effective in retaining metribuzin in the soils. Metribuzin sorption in the IP fly ash-amended soils showed strong correlation with the fly ash content and compared to K_f/K_d values, K_FA values (sorption normalized to fly ash content) showed less variation. Metribuzin sorption-desorption did not correlate to the organic carbon content of the soil-fly ash mixture. The study demonstrates that all coal fly ashes may not be effective in enhancing the sorption of metribuzin in soils to the same extent. However, among the fly ashes used in this study, the IP fly ash was observed to be significantly effective in enhancing the sorption of metribuzin in soils. This may play an important role in reducing the run off and leaching losses of the herbicide by retaining it in the soil.     

粉煤灰砖块对磷酸盐的吸附特性

以建筑废料粉煤灰砖块为吸附剂材料,通过静态吸附实验研究其对磷酸盐的吸附特征,以及磷酸盐初始浓度、吸附剂投加量、pH等因素对吸附反应的影响。Langmuir、Freundlich和Temkin等温模型的分析发现,Langmuir等温式方程最适合描述吸附过程,对磷酸盐的理论饱和吸附容量为44.62 mg/g。利用伪一级动力学模型、伪二级动力学模型和颗粒内扩散模型考察了吸附过程特征,其中伪二级动力学模型为最适于描述粉煤灰砖块对磷酸盐的吸附过程的动力学模型。通过颗粒内扩散模型、Bangham方程及Boyd模型对吸附动力学机理进行的探讨表明,颗粒内扩散速率不是粉煤灰砖块吸附磷酸盐反应的惟一速率控制步,膜扩散速率和颗粒内扩散速率共同影响着吸附反应速率。磷酸盐浓度较低时主要是膜扩散限制吸附反应速率,而磷酸盐浓度较高时则颗粒内扩散成为速率控制步。研究证明,粉煤灰砖块粉末作为湿地基质具有对磷酸盐很强的吸附能力,在减少了固体废弃物的数量的同时又可以实现水污染控制的目的。     

Removal of arsenic species from water by batch and column operations on bagasse fly ash

Bagasse fly ash (BFA, a sugar industrial waste) was used as low-cost adsorbent for the uptake of arsenate and arsenite species from water. The optimum conditions for the removal of both species of arsenic were as follows: pH 7.0, concentration 50.0 μg/L, contact time 50.0 min, adsorbent dose 3.0 g/L, and temperature 20.0 °C, with 95.0 and 89.5 % removal of arsenate and arsenite, respectively. The Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich adsorption isotherms were used to analyze the results. The results of these models indicated single-layer uniform adsorption on heterogeneous surface. Thermodynamic parameters, i.e., ΔG°, ΔH°, and ΔS°, were also calculated. At 20.0 to 30.0 °C, the values of ΔG° lie in the range of ?4,722.75 to ?4,878.82 and ?4,308.80 to ?4,451.73 while the values of ΔH° and ΔS° were ?149.90 and ?121.07, and 15.61 and 14.29 for arsenate and arsenite, respectively, indicating that adsorption is spontaneous and exothermic. Pseudo-first-order kinetics was followed. In column experiments, the adsorption decreased as the flow rate increased with the maximum removal of 98.9 and 95.6 % for arsenate and arsenite, respectively. The bed depth service time and Yoon and Nelson models were used to analyze the experimental data. The adsorption capacity (N _o) of BFA on column was 3.65 and 2.98 mg/cm³ for arsenate and arsenite, respectively. The developed system for the removal of arsenate and arsenite species is economic, rapid, and capable of working under natural conditions. It may be used for the removal of arsenic species from any contaminated water resources.     

铁屑粉煤灰组合处理含磷废水

实验研究了铁屑粉煤灰组合处理含磷废水的除磷效果.通过单因素实验,考查了铁屑粉煤灰质量比、反应时间、pH值和投加量对除磷效果的影响.实验结果表明,该法除磷的最优条件为铁屑和粉煤灰的质量比为2∶1,反应时间为20 min,pH值为6,投加量为20 g/L.在最优实验条件下磷的去除率达到了97.5％.对比了该法和粉煤灰吸附法与传统铁屑法的除磷效果.与单一粉煤灰吸附法和传统铁屑法除磷的结果相比较,铁屑粉煤灰组合除磷的方法具有明显优势.     

Removal of cationic dyes from aqueous solutions using microspherical particles of fly ash

Batch sorption experiments were carried out for the removal of cationic dyes (methylene blue and malachite green) from their aqueous solutions using sorbent made from fly ash-a waste material. Effects of various experimental parameters: initial dye concentration, contact time, pH, adsorbent dosage, solution temperature, surfactant addition and ionic strength on the fly ash sorption of dyes were evaluated. The isothermal data for sorption followed the Langmuir model. The maximum sorption capacity obtained for methylene blue and malachite green was 36.05 mg/g and 40.65 mg/g, respectively. Kinetic studies indicate that sorption on fly ash follows the pseudo-second order kinetics. Present research suggests that fly ash could be an appropriate adsorbent for the removal of basic dyes from aqueous solutions.     

Immobilization and volume reduction of heavy metals in municipal solid waste fly ash using nano-size calcium and iron-dispersed reagent

This study was conducted to examine the synthesis and application of novel nano-size calcium/iron-based composite material as an immobilizing and separation treatment of the heavy metals in fly ash from municipal solid waste incineration. After grinding with nano-Fe/Ca/CaO and with nano-Fe/Ca/CaO/[PO₄], approximately 30 wt% and 25 wt% of magnetic fraction fly ash were separated. The highest amount of entrapped heavy metals was found in the lowest weight of the magnetically separated fly ash fraction (i.e., 91% in 25% of treated fly ash). Heavy metals in the magnetic or nonmagnetic fly ash fractions were about 98% and 100% immobilized, respectively. Additionally, scanning electron microscopy combined with energy-dispersive X-ray spectrometry (SEM-EDS) observations indicate that the main fraction of enclosed/bound materials on treated fly ash includes Ca/PO₄-associated crystalline complexes. After nano-Fe/Ca/CaO/[PO₄] treatment, the heavy metal concentrations in the fly ash leachate were much lower than the Japan standard regulatory limit for hazardous waste landfills. These results appear to be extremely promising. The addition of a nano-Fe/Ca/CaO/PO₄ mixture with simple grinding technique is potentially applicable for the remediation and volume reduction of fly ash contaminated by heavy metals.

Implications: After grinding with nano-Fe/Ca/CaO and nano-Fe/Ca/CaO/[PO₄], approximately 30 wt% and 25 wt% of magnetic fraction fly ash were separated. The highest amount of entrapped heavy metals was found in the lowest weight of the magnetically separated fly ash fraction (i.e., 91% in 25% of treated fly ash), whereas heavy metals either in the magnetic or nonmagnetic fly ash fractions were about 98% and 100% immobilized. These results appear to be very promising, and the addition of nano-Fe/Ca/CaO/PO₄ mixture with simple grinding technique may be considered potentially applicable for the remediation and volume reduction of contaminated fly ash by heavy metals.     

Synthesis of high-purity Na-A and Na-X zeolite from coal fly ash

Coal fly ash (CFA) was used as a raw material for the synthesis of zeolite molecular sieve. The synthesis began with the pretreatment of CFA to remove impurities (e.g., Fe₂O₃, CaO, etc.) under various acid types (HCl, H₂SO₄, and HNO₃) and acid/CFA ratios (5–25 mL_acid/g_CFA). High product purity (up to 97%) was achieved with HCl (20%wt), and acid/CFA ratio of 20 mL_HCl/g_CFA. The treated CFA was then converted to zeolite by the fusion reaction under various Si/Al molar ratios (0.54–1.84). Zeolite type A was synthesized when the Si/Al molar ratios were lower than 1, whereas sodium aluminum silicate hydrate was formed when the Si/Al molar ratio were higher than 1. The highest water adsorption performance of the zeolite product, i.e., the outlet ethanol concentration of 99.9%wt and the specific adsorption capacity of 2.31 × 10^?2 g_water/g_zeolite, was observed with the Si/Al molar ratio of 0.82. The zeolite was tested for its water adsorption capacity repeatedly 10 times without deactivation.

Implications: This work evaluated the technical feasibility in the conversion of CFA to zeolite, which would help reduce the quantity of waste needed to be landfilled. This adds value to the unwanted material by converting it into something that can be further used. The synthesized products were shown to be quite stable as water adsorbent for the dehydration of ethanol solution.     

粉煤灰负载铁离子催化氧化活性黄染料废水

以粉煤灰为载体,制备铁/粉煤灰负载型催化剂,并利用该催化剂催化H2O2氧化降解活性黄染料废水,探讨了H2O2投加量、催化剂投加量、染料初始浓度和初始pH值等因素对染料废水COD去除率和脱色率的影响。结果表明,当染料废水COD初始浓度为200 mg/L,初始pH值为1.7,投加0.5 g/100 mL催化剂及加入1.0 mL浓度为1.13 mol/L的H2O2溶液时,处理效果最好,此时染料废水的COD去除率和脱色率分别达到63%和99%,并且废水的可生化性得到很大的提高。利用该负载催化剂能够有效地减少活性黄染料废水中Fe3+的残留量。     

Effect of fly ash on metsulfuron-methyl sorption and leaching in soils

This investigation was undertaken to determine the effect of amendment of two fly ashes [Kota and Inderprastha (IP)] on sorption behavior of metsulfuron-methyl in three Indian soil types. Kota fly ash (5%) did not show any effect on herbicide sorption while IP fly ash significantly enhanced the sorption. Further studies on metsulfuron-methyl sorption-desorption behavior in 0.5, 1, 2, and 5% IP fly ash-amended soils suggested that effect of fly ash varied with soil type and better effect was observed in low organic carbon content soils. The sorption-desorption isotherms fitted very well to the Freundlich sorption equation and, in general, slope (1/n) values less than unity were observed. Metsulfuron-methyl sorption in the IP fly ash-amended soils showed strong correlation with the fly ash content and compared to the Freundlich sorption constant (K _f), K _FA values (sorption normalized to fly ash content) showed less variation. Metsulfuron-methyl leaching studies suggested greater retention of herbicide in the application zone in IP fly ash-amended soils, but effect varied with soil type and no herbicide leaching was observed in 5% fly ash-amended soils. The study suggested that all coal fly ashes are not effective in enhancing the sorption of metsulfuron-methyl in soils. However, one which enhanced herbicide sorption, could play an important role in reducing its leaching losses.     

改性粉煤灰吸附稀土废水中的氨氮

用硫酸和氢氧化钠对粉煤灰进行酸改性和碱改性处理,研究改性前后粉煤灰对稀土废水中氨氮的吸附效果变化及最佳吸附条件,并从吸附等温线入手探讨吸附机理。结果显示,经碱改性后粉煤灰对氨氮的吸附性能有明显改善,当最佳吸附条件确定为投加量2 g,吸附时间2 h,初始pH 7～8时,碱改性粉煤灰对氨氮的吸附过程符合Freundlich等温方程式和Langmuir等温方程式。碱改性粉煤灰对氨氮的吸附属于良性吸附,且为吸热过程,室温下理论饱和吸附量为1.9066mg/g。