pH调节-Fenton试剂氧化法预处理间甲酚生产氧化废水

采用pH调节结合Fenton试剂氧化的方法对间甲酚生产氧化废水进行预处理,探讨了pH调节条件及Fenton试剂氧化条件对废水处理效果的影响。结果表明,在室温下将废水pH调节至4．0时,由于其中的部分有机污染物析出,COD可以从78000mg／L下降至61000mg／L,COD去除率达20％以上;接着在H2O2质量浓度与COD的比值为0．18、Fe^2＋与H2O2质量浓度的比值为0．267、反应时间为20min的条件下对废水进行Fenton试剂氧化处理,COD可以进一步下降至26000mg／L,COD去除率接近70％。     

UV/Fenton氧化-混凝联合工艺处理含酚废水

采用UV／Fenton氧化-混凝联合工艺对模拟苯酚废水进行处理,探讨了UV／Fenton预氧化程度和混凝处理条件对模拟苯酚废水处理效果的影响。结果表明,采用混凝处理,COD去除率仅为14．1％;当UV／Fenton预氧化处理过程中H2O2的质量浓度为150～300mg／L时,废水的混凝性能可提高1．5倍以上;当H2O2质量浓度为450mg／L、光反应时间为30min时,采用UV／Fenton氧化一混凝工艺联合处理后COD去除率达82．7％。苯酚废水采用UV／Fenton预氧化处理后,进行混凝处理过程的适宜pH为6．5,混凝剂Fe^3 的适宜质量浓度为500mg／L.     

Fenton氧化-生物接触氧化工艺处理甲醛和乌洛托品废水

采用Fenton氧化一生物接触氧化工艺处理含甲醛和乌洛托品的模拟废水（简称废水），在H2O2（体积分数30％）加入量2．5g／L、H2O2与Fe^2＋质量浓度比3．75、反应时间3h、不调节废水初始pH的Fenton氧化预处理最佳操作条件下，废水COD从1000mg／L左右降至300mg／L，COD去除率达72％。原废水完全无法直接进行生化处理，经Fenton氧化预处理后其BOD，／COD约为0．5，易于生化处理。Fenton氧化一生物接触氧化工艺处理废水，生物接触氧化停留时间为12h时，废水COD去除率高达94％，处理后出水COD小于70mg／L，处理效果很好。     

絮凝沉淀-Fenton试剂氧化法处理含高浓度硫酸盐的洗涤剂生产废水

采用絮凝沉淀-Fenton试剂氧化法处理含高浓度硫酸盐的洗涤剂生产废水（简称废水），考察了各种因素对COD去除率的影响。实验结果表明：根据实际废水的水质情况，选用聚合氯化铝（PAC）为絮凝剂，PAC最佳加入量为0．3g／L，经絮凝处理后COD去除率为42．3％；Fenton试剂氧化的最佳操作条件为：n（H2O2）：n（Fe^2＋）=0．5、H2O2加入量为7mmol／L、反应时间为2h，不调节废水初始pH，经Fenton试剂氧化处理后COD去除率为70％以上。经絮凝沉淀-Fenton试剂氧化法处理后，废水COD由1950mg／L降至240mg／L，总的COD去除率为87．7％，废水处理效果良好。     

膜法处理难降解石化废水的预处理工艺研究

采用混凝法分别以聚合氯化铁（PFC）、聚合氯化铝（PAC）和聚合硫酸铁（PFS）为混凝剂处理天津某石油化工厂二级氧化处理工艺出水，PFC对废水COD的去除效果最好，在PFC加入量为120mg／L时，废水的COD去除率最高，为22．35％。经正交实验确定了Fenton试剂氧化法处理废水的最佳实验条件为：Fe^2＋加入量290mg／L、H2O2加入量100mg／L、pH=6、反应时间30min，此时COD去除率为20．45％。活性炭吸附法对废水的处理效果随活性炭加入量增加而改善，活性炭的最佳加入量为2000mg／L，此时废水的COD去除率最高，为87．78％。     

微波-改性活性炭-Fenton试剂氧化法降解水中2,4-二氯酚

以经Fe2（SO4）3溶液浸渍改性的活性炭作催化剂、Fenton试剂作氧化剂，采用微波-改性活性炭-Fenton试剂氧化法降解水中的2，4-二氯酚。考察了改性活性炭加入量、H2O2与Fe^2＋摩尔比、Fenton试剂加入量、微波功率和2，4-二氯酚溶液初始pH对2，4-二氯酚降解效果的影响。在改性活性炭加入量1．0g／L、n（H2O2）：n（Fe^2＋）=16．7（H2O2加入量6．0mmol／L、Fe^2＋加入量0．36mmol／L）、Fenton试剂加入量为6．36mmol／L、微波功率600W、微波辐射时间10min、2，4-二氯酚溶液初始pH为6．0的条件下，2，4-二氯酚降解率和TOC去除率分别可达98．7％和84．0％。     

高铁酸钾预氧化-三氯化铁混凝去除水中AS^3＋

采用K2FeO4预氧化-Fecl3混凝联合去除水中的As^3＋，考察了适宜的K2FeO4预氧化时间、Fe^3＋和Fe^6＋加入量，分析了预氧化pH、混凝pH、碳酸盐和腐殖酸浓度对该工艺去除As^3＋效果的影响。实验结果表明：K2FeO4预氧化的适宜时间为2min；加入质量浓度为2．4mg／L的Fe^6＋和14．0mg／L的Fe^3＋能使处理后水样中的As^3＋浓度符合GB-57492006《生活饮用水卫生标准》（As^3＋质量浓度小于0．01mg／L）；预氧化pH在4～9范围内，对K2FeO4预氧化-FeCl3混凝去除As^3＋的效果影响不大；FeCl3混凝阶段适宜的pH为6．0～8．5。碳酸盐对K2FeO4预氧化-Fecl，混凝去除As^3＋的效果基本没有影响；腐殖酸的存在使As^3＋的去除率有一定程度的降低。     

混凝—催化氧化法处理丁苯橡胶生产废水

以聚合氯化铝（PAC）、阴离子聚丙烯酰胺（PAM）为混凝剂，以H2O2-O3为氧化剂，采用混凝-催化氧化法处理对丁苯橡胶生产废水。考察了混凝剂种类及其加入量、废水pH对混凝处理效果的影响，氧化剂及其加入量、反应时间和废水pH对COD去除率的影响。实验得出的最佳工艺条件：混凝实验，废水pH为7、PAC和PAM加入量为400mg／L和4mg／L；催化氧化实验，废水pH为7～8、H2O2加入量为200mg／L、H2O2与O3的质量比为0．5。处理后，废水COD从860mg／L降至145mg／L，COD去除率达83．1％，出水水质达到国家二级排放标准。     

H2O2协同TiO2光催化处理模拟苯胺废水

采用TiO2光催化处理模拟苯胺废水.实验结果表明,最佳反应条件为:初始苯胺质量浓度10 mg/L,纳米TiO2加入量100 mg/L,光催化反应时间60 min,废水pH 7.5.加入20 mg/L的H2O2协同TiO2光催化处理苯胺废水,光催化反应24 min后,苯胺去除率达99％.H2O2协同TiO2光催化降解苯胺过程符合二级动力学方程.     

超声辐射法降解废水中的二甲苯、苯酚和丙烯腈

采用频率为20kHz的超声波处理二甲苯、丙稀腈、苯酚溶液。实验结果表明，在二甲苯初始质量浓度为27．6mg／L、H2O2质量浓度为1．68g／L、溶液温度为25℃、声强为141．32W／cm^2、辐射全程时间为60min的条件下，二甲苯降解率可达99．20％；在丙烯腈初始质量浓度为100．0mg／L、通氧量为15mL／rain、溶液温度为28℃、声强为141．32W／cm^2、辐射全程时间为30rain的条件下，丙烯腈降解率可达98．20％；在苯酚初始质量浓度为20．0mg／L、H202质量浓度为1．50g／L、FeSO4质量浓度为0．22g／L、溶液温度为28℃、声强为48．92W／cm^2、辐射全程时间为40rain的条件下，苯酚降解率可达99．81％。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Heavy Metals Removal by Biosorption and Flotation

The removal of a mixture of heavy (toxic) metal cations (copper, nickeland zinc) from liquid effluents was investigated in this study at pilotscale, using counter-current contact mode. The innovative processinvolved the abstraction of metal ions onto fungal biosorbents, followedby the application of flotation for the subsequent solid/liquid separationof biomass particles. The ability of microorganisms to remove metal ionsfrom aqueous solutions is a well-known phenomenon. Nevertheless,engineering considerations are very important in decisions, concerningthe commercial future of biosorption and practical solutions are neededfor certain problems, such as the efficient post-separation ofmetal-loaded biomass. The two processes (flotation and biosorption) caneffectively operate in combination, in what it was termed biosorptiveflotation process. The sorbents may be recycled, after appropriate elutionof metals, as well as the treated (clean) water.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩，馏出液经铁炭氧微电解和混凝预处理，再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下，处理后出水pH6～9，COD 302mg／L，BOD5 108mg／L，SS30mg／L，色度36倍，水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.