固硫灰固化焦化废水处理外排污泥

采用机械力化学法活化循环流化床燃煤固硫灰,用于固化焦化废水处理外排污泥(CWT污泥)。探讨了固硫灰活化条件,并通过XRD和FTIR分析了固硫灰固化CWT污泥中重金属的机理。实验结果表明:当m(Ca O)∶m(Ca O+固硫灰)为20%、球磨频率为40 Hz、球磨时间为2 h时,养护28 d固硫灰固化体的平均抗压强度达到72.2 MPa;当污泥掺加量为50%(w)时,养护28 d含污泥固化体的抗压强度达到8.5 MPa,固化体浸出液中Pb2+和As5+的质量浓度分别为0.177 mg/L和0.013 mg/L,均远低于GB 5085.3—2007《危险废物鉴别标准浸出毒性鉴别》的规定限值。XRD和FTIR表征结果表明,在固硫灰活化过程中,混合体系水化生成了C—S—H凝胶、斜方钙沸石和钙矾石,可通过物理包裹、吸附及离子交换的形式实现CWT污泥中Pb2+和As5+的固化/稳定化。     

《化工环保》2003年总目次

研究报告反硝化处理硝氮废水的动力学研究杜丽平 ,等………………………………………………………… 1 1强碱性离子交换树脂再生新工艺的研究赵会义 ,等…………………………………………………… 1 5树脂吸附法处理磺胺中间体生产废水的研究孙越 ,等………………………………………………… 1 9钙类化合物固硫作用动力学分析李宗孝 ,等…………………………………………………………… 1 14混合填充体系对铬渣中六价铬的阻留作用刘彬 ,等…………………………………………………… 2 6 3吸附—混凝—紫外光催化氧化法处理医药废水的研究黄…     

天然气再燃添加有机酸盐同时降低SO2及NOx的机理研究

对天然气再燃过程中添加的有机酸盐同时脱硫、脱氮反应途径及机理进行了详细的分析.探讨了有机酸盐(钙镁醋酸盐CMA)分解的CHi还原NO的主要机理,研究了CMA固硫的反应机理,分析了脱硫过程影响HCN、NH3还原NO的因素.提出了天然气再燃添加CMA同时脱硫、脱氮时,也要综合考虑CaO对SO2的脱除和对NO生成的促进作用.     

油页岩在流化床燃烧过程中放硫与固硫的数学模拟研究

为预测油页岩粒度、床温、钙硫比、床中灰分含量等参数对流化床二氧化硫排放量的影响，本文开发了耦合油页岩燃烧放硫、石灰石固硫和灰粒固硫的综合模型，并将该模型的预测值与实验结果进行了比较，发现两者吻合良好。本文的工作是研究工业化连续式油页岩流化床燃烧脱硫的基础，对茂名建设５万千瓦油页岩流化床燃烧热电站有重要的参考价值，并对于研究煤的燃烧利用有借鉴意义。     

Fe_2O_3和K_2CO_3对钙基添加剂脱硫脱硝的影响

在研究焦炭燃烧过程中使用钙基添加剂固硫的基础上,探讨了Fe_2O_3或K_2CO_3对CaO脱硫脱硝的影响。实验结果表明:添加剂的种类对焦炭燃烧过程中排放的SO_2和NO的浓度及总量均有一定的影响;加入Fe_2O_3或K_2CO_3替代部分CaO后,焦炭燃烧过程中排放的SO_2和NO比单独加入CaO时均有所下降;向焦炭中分别混合3.0%(w)CaO),1.5%(w)CaO+1.5%(w)Fe_2O_3,1.5%(w)CaO+1.5%(w)K_2CO_3的添加剂时,焦炭的SO_2排放总量分别降低了69.93%,75.98%,79.98%,NO排放总量分别降低了64.38%,79.73%,84.14%;加入Fe_2O_3或K_2CO_3后,钙基添加剂的表面性质发生了变化,同时增加了反应的活性中心数,因而复合添加剂能更有效地进行脱硫脱硝。     

碱熔融活化固硫灰制备地聚合物

采用碱熔融活化法，由固硫灰制备地聚合物。在前期开展的单因素实验的基础上，采用正交实验，考察了NaOH和固硫灰的质量比、煅烧温度、煅烧时间3个因素对固硫灰基地聚合物的抗压强度的影响。采用XRD，SEM，IR等手段分析固硫灰碱熔融活化前后的物相、微观形貌以及硅铝化学键的变化。实验结果表明，以在NaOH与固硫灰的质量比为0.60、煅烧温度为550 ℃、煅烧时间为60 min的条件下制备的碱熔融固硫灰为原料，制备的固硫灰基地聚合物的抗压强度为38.00 MPa。表征结果显示：通过碱熔融活化固硫灰制备的地聚合物的XRD谱图中出现了地聚合物的特征衍射峰;碱熔融固硫灰的结构松散，在颗粒表面及内部存在大量孔隙;经碱熔融处理后固硫灰的硅酸盐和铝酸盐发生了解聚。     

超滤膜系统污染物的形貌及组成分析

通过SEM、能谱、FTIR以及电感耦合等离子体质谱的分析方法对被污染超滤膜面的无机污染物、有机污染物和微生物进行了识别和分析。研究结果表明:超滤膜面无机污染物主要为Fe(OH)3、Cu(OH)2、Al(OH)3和Si等胶体物和少量CaSO4;有机污染物主要为多菌霉素类化合物;微生物可能富含铁类化合物。同时污染膜的清洗液分析结果说明该超滤膜污染物主要为无机胶体和有机物。     

固硫剂制备工艺探讨

探讨了循环流化床锅炉脱硫方法中固硫剂的制备工艺，对几种石灰石破碎设备及工艺进行了分析比较，通过柱磨机粉磨石灰石的工业试验，了解其产品粒度分布，从而择优确定固硫剂制备工艺流程。     

半干法脱除球团烟气中的SO2及Hg0

采用钙基吸收剂及复合氧化剂半干法脱除模拟球团烟气中的SO_2及Hg~0,考察了多因素条件对吸收效果的影响。实验结果表明,在以NaClO和NaClO_2为复合氧化剂、 NaClO与NaClO_2体积比1∶0.5、复合氧化剂质量分数3%、反应温度110℃、钙基吸收剂质量3.0 g、模拟烟气进气流量1.2 L/min的条件下,SO_2和Hg~0的脱除率分别为98%和93%,证明钙基吸收剂与复合氧化剂对污染物球团烟气中的SO_2和Hg~0有良好的脱除作用。     

二恶英类化合物检测方法的研究现状及展望

介绍了二恶英类化合物的检测方法,并对各种检测方法的原理和应用进行了对比分析;其中高分辨率色谱/质谱法、荧光素酶报告基因法及酶免役分析法在实践中取得了很好的检测效果;CALUX 法与其他生物检测方法相比更适合于大批量样品中二恶英含量的快速定量筛选,对于二恶英污染调查有广阔的应用前景;综述了我国二恶英类化合物检测方法的研究现状,并对我国开展二恶英分析监测提出了建议和展望.     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Heavy Metals Removal by Biosorption and Flotation

The removal of a mixture of heavy (toxic) metal cations (copper, nickeland zinc) from liquid effluents was investigated in this study at pilotscale, using counter-current contact mode. The innovative processinvolved the abstraction of metal ions onto fungal biosorbents, followedby the application of flotation for the subsequent solid/liquid separationof biomass particles. The ability of microorganisms to remove metal ionsfrom aqueous solutions is a well-known phenomenon. Nevertheless,engineering considerations are very important in decisions, concerningthe commercial future of biosorption and practical solutions are neededfor certain problems, such as the efficient post-separation ofmetal-loaded biomass. The two processes (flotation and biosorption) caneffectively operate in combination, in what it was termed biosorptiveflotation process. The sorbents may be recycled, after appropriate elutionof metals, as well as the treated (clean) water.     

Selection of Autochthonous Plant Species from SE Spain for Soil Lead Phytoremediation Purposes

Mining activity in SE of Spain, in the west Mediterranean coast, originated more than two millenniums ago. It has generated huge areas affected by heavy metals contamination, especially of lead, which is possibly one of the most important. Investigations related to the selection of autochthonous plant taxa from a typical Spanish Mediterranean area, useful for phytoextraction and phytostabilization purposes in these polluted areas are shown. Under these edaphoclimatic conditions 12 interesting species were considered, from them six taxa were chosen for further studies. Some plant species have been proposed either for phytoextraction or phytostabilization purposes. Recommendations for further research have been discussed.     

Concentrations and Pools of Heavy Metals in Urban Soils in Stockholm,Sweden

The concentrations of heavy metals (Cd, Cr, Cu, Hg, Ni, Pb andZn) and arsenic (As) were surveyed and the metal pools estimatedin soils in Stockholm Municipality. The sampling sites were distributed all over the entire municipality with a higher sampling density in the city centre. Soils were sampled to a maximum depth of 25 to 60 cm. Soil texture, total-C content, electrical conductivity and pH were analysed. Heavy metal concentrations were determined after wet digestion with boiling7 M HNO₃.The results showed a wide range in heavy metal concentrations, as well as in other soil properties. The city centre soils constituted a rather homogeneous group whereas outside this areano geographical zones could be distinguished. These soils were grouped based on present land use, i.e. undisturbed soils, public parks, wasteland (mainly former industrial areas), and roadside soils. The city centre and wasteland soils generally hadenhanced heavy metal concentrations to at least 30 cm depth compared to park soils outside the city centre and rural (arable)soils in the region, which were used to estimate background levels. For example, the mean Hg concentration was 0.9 (max 3.3)mg kg^-1 soil at 0–5 cm and 1.0 (max 2.9) at 30 cm depth in the city centre soils, while the background level was 0,04 mg kg^-1. Corresponding values for Pb were 104 (max 444) and135 (max 339) mg kg^-1, at 0–5 and 30 cm, respectively, while the background level was 17 mg kg^-1.The average soil pools (0–30 cm depth) of Cu, Pb and Zn were 21,38 and 58 g m^-2 respectively, which for Pb was 3–4 timeshigher and for Cu and Zn 1.5–2 times higher than the backgroundlevel. The total amount of accumulated metals (down to 30 cm)in the city centre soils (4.5^*10 ⁶ m² public gardens and green areas) was estimated at 80, 1.1, 120 and 40 t for Cu, Hg, Pb and Zn, respectively. The study showed (1) thatfrom a metal contamination point of view, more homogeneous soilgroups were obtained based on present land use than on geographicdistance to the city centre, (2) the importance of establishing a background level in order to quantify the degree of contamination, and (3) soil samples has to be taken below the surface layer (and deeper than 30 cm) in order to quantify theaccumulated metal pools in urban soils.