Ammonium removal from landfill leachate by chemical precipitation

The landfill leachate in Hong Kong usually contains quite high NH₄⁺–N concentration, which is well known to inhibit nitrification in biological treatment processes. A common pre-treatment for reducing high strength of ammonium (NH₄⁺–N) is by an air-stripping process. However, there are some operational problems such as carbonate scaling in the process of stripping. For this reason, some technical alternatives for NH₄⁺–N removal from leachate need to be studied. In this study, a bench-scale experiment was initiated to investigate the feasibility of selectively precipitating NH₄⁺–N in the leachate collected from a local landfill in Hong Kong as magnesium ammonium phosphate (MAP). In the experiment, three combinations of chemicals, MgCl₂·6H₂O+Na₂HPO₄·12H₂O, MgO+85% H₃PO₄, and Ca(H₂PO₄)₂·H₂O+MgSO₄·7H₂O, were used with the different stoichiometric ratios to generate the MAP precipitate effectively. The results indicated that NH₄⁺–N contained in the leachate could be quickly reduced from 5618 to 112 mg/l within 15 min, when MgCl₂·6H₂O and Na₂HPO₄·12H₂O were applied with a Mg²⁺:NH₄⁺:PO₄³⁻ mol ratio of 1:1:1. The pH range of the minimum MAP solubility was discovered to be between 8.5 and 9.0. Attention should be given to the high salinity formed in the treated leachate by using MgCl₂·6H₂O and Na₂HPO₄·12H₂O, which may affect microbial activity in the following biological treatment processes. The other two combinations of chemicals [MgO+85% H₃PO₄ and Ca(H₂PO₄)2·H₂O+MgSO₄·7H₂O] could minimise salinity after precipitation, but they were less efficient for NH₄⁺–N removal, compared with MgCl₂·6H₂O and Na₂HPO₄·12H₂O. COD had no significant reduction during this precipitation. It was found that the sludge of MAP generated was easily settled within 10 min to reach its solids content up to 27%. The other characteristics including capillary suction time (CST) and dry density (DD) of the MAP sludge were also tested. The experimental results indicate that the settled sludge is quite solid and can be directly dumped at a landfill site even without any further dewatering treatment.     

Preparation of Natural Rubber/Condensed Tannin Semi-interpenetrating Polymer Network Composites by Hematin-Catalyzed Cross-Linking

In this study, the preparation of semi-interpenetrating polymer network (semi-IPN) composites composed of natural rubber and condensed tannin was performed by means of the enzyme-mimetic cross-linking of condensed tannin catalyzed by hematin. Prior to the preparation of the composites, the hematin-catalyzed cross-linking behavior of condensed tannin was evaluated by the TGA measurement. The TGA results indicated that condensed tannin was sufficiently cross-linked by the hematin-catalyzed reaction in the presence of appropriate amounts of 30% (w/v) H₂O₂ aq. to give the relatively thermostable materials. For the preparation of the composites, a solution of condensed tannin and hematin, and subsequently 30% (w/v) H₂O₂ aq. were added to natural rubber latex and the mixture was stirred at room temperature for 10 min to perform the cross-linking of condensed tannin, followed by drying of the reaction mixture at 50 °C for 5 h, which was subsequently put into a heat device and hot-pressed at 100 °C and 20 MPa for 20 min to give the semi-IPN composite. The tensile stress?Cstrain measurement of the composites was conducted to evaluate the mechanical properties, which were changeable depending on the weight ratios of natural rubber to condensed tannin and the amounts of 30% (w/v) H₂O₂ aq. Moreover, the miscibility of the cross-linked tannin with natural rubber in the composite was evaluated by the SEM measurement.     

New Methods for the Preparation Nanosized Metal Coordination Polymers

Transition-metal coordination polymers [M(ndc)(bpy)·(H₂O)m]·xH₂O (where M = Co(II), Ni(II), Cu(II) and Zn(II), ndc = 1,4-naphthalenedicarboxylate, bpy = 4,4′-bipyridine; m = 0 or 1; x = 1 or 2) were prepared by reacting the ligands and metal ions at room temperature with the aid of microwave irradiation and sonication methods. The structure of the coordination polymers was assigned based on elemental analysis, FT-IR and electronic spectral studies, thermal analysis, scanning electron microscope and X-ray powder diffraction. Thermogravimetric analysis was also used to follow up the possible thermal decomposition steps and to calculate the thermodynamic parameters of the nano-sized metal complexes. The kinetic parameters were calculated making use of the Coats–Redfern and Horowitz–Metzger equations. All obtained results of the different technics used in our study stated the ability to synthesis the metal coordination polymers of our interest using both microwave irradiation and sonication methods.     

Archaeal Poly (3-hydroxybutyrate) Polymer Production from Glycerol: Optimization by Taguchi Methodology

In this study the possibility of poly (3-hydroxybutyrate) production from glycerol was investigated and optimized by Halorcula sp. IRU1, a novel archaea isolated from Urmia lake, Iran in batch experiments. Using Taguchi methodology, three important independent parameters (glycerol, yeast extract and KH₂PO₄) were evaluated for their individual and interactive effects on poly (3-hydroxybutyrate) production. It was shown that the glycerol concentration was the most significant factor affecting the yield of poly (3-hydroxybutyrate). The optimum factor levels were a glycerol concentration of 8% (v/v), yeast extract 0.8% (w/v) and KH₂PO₄ 0.002% (w/v). The predicted value obtained for poly (3-hydroxybutyrate) production under these conditions was about 81.87%. We can conclude that Haloarcula sp. IRU1 has a high potential for synthesis of poly (3-hydroxybutyrate) from glycerol.     

Thermogravimetric and XRD study of the effects of chloride salts on the thermal decomposition of mercury compounds

In this paper, the effects of chloride salt (MgCl₂, CaCl₂ or NaCl) addition on the thermal decomposition of five inorganic mercury compounds (HgCl₂, HgS, Hg(NO₃)₂·H₂O, HgO, and HgSO₄) were investigated by thermogravimetric analysis. Mercury-contaminated soil samples collected from Inner Mongolia were used to verify the results. The desorption temperatures of the mercury compounds increased in the following order: HgCl = HgCl₂ < HgS < Hg(NO₃)₂·H₂O < HgO < HgSO₄. Among the chloride salts, MgCl₂ had the greatest effect on thermal desorption of the mercury compounds, with the greatest reduction in the initial temperature of thermal desorption. After MgCl₂ treatment, the mercury removal rates for the soil were 65.67–81.35 % (sample A), 70.74–84.91 % (sample B), and 69.08 % (sample C). The increase in the mercury removal rate for sample C with addition of MgCl₂ was particularly large (34.96–69.08 %). X-Ray diffraction analysis of white crystals from the thermal desorption with MgCl₂ indicated that MgCl₂ promoted conversion of the mercury compounds in the soil to mercury(II) chloride and dimercury dichloride. This transformation is beneficial for applying thermal desorption to remedy mercury-contaminated soils and treat of mercury containing waste.     

Dechlorination and decomposition of Aroclor 1242 in real waste transformer oil using a nucleophilic material with a modified domestic microwave oven

This research was done to assess the dechlorination and decomposition of polychlorinated biphenyls (PCBs) in real waste transformer oil through a modified domestic microwave oven (MDMW). The influence of microwave power (200–1000 W), reaction time (30–600 s), polyethylene glycol (PEG) (1.5–7.5 g), iron powder (0.3–1.5 g), NaOH (0.3–1.5 g), and H₂O (0.4–2 ml) were investigated on the decomposition efficiency of PCBs existing in real waste transformer oil with MDMW. Obtained data indicate that PEG and NaOH have the greatest influence on decomposition of PCBs; while, iron did not influence, and H₂O decreased, the decomposition efficiency of PCBs. Experimental data also indicated that with the optimum amount of variables through a central composites design method (PEG = 5.34 g, NaOH = 1.17 g, Fe = 0.6 g, H₂O = 0.8 ml and microwave power 800 W), 78 % of PCBs was degraded at a reaction time of about 6 min. In addition, the PCBs decomposition without using water increased up to 100 % in the reactor with the MDMW at 6 min. Accordingly, results showed that MDMW was a very efficient factor for PCBs decomposition from waste transformer oil. Also, using microwave irradiation, availability and inexpensive materials (PEG, NaOH), and iron suggest this method as a fast, effective, and cheap method for PCB decomposition of waste oils.     

Nucleophilic substitution of poly(vinyl chloride) with iminoacetic acid and n-dodecanethiol

The modification of poly(vinyl chloride) was carried out with iminodiacetic acid (IDA, C₄H₇NO₄) and iminodiacetic acid dimethylester (IDADM, C₆H₁₁NO₄), as well as with n-dodecanethiol (DT, C₁₂H₂₆S) in the presence of K₂CO₃. The reaction was carried out at different temperatures below 100 °C with dimethyl formamide (DMF) and cyclohexanone as solvents. IDA did not show any reactivity, probably due to the dipolar character of the molecule. IDADM caused the elimination of HCl, while only substitution ratios of about 3 % were observed. However, the modification of PVC with DT resulted in a substitution rate of 18 % without elimination. DT-PVC showed excellent thermal properties, comparable with those of the unmodified polymer.     

Conjugation of Soybean Oil and It’s Free-Radical Copolymerization with Acrylonitrile

The conjugated soybean oil was synthesized through the isomerization reaction of soybean oil to transformed the structure of linoleic acid into conjugated linoleic acid structure, and Rhodium complexes (RhCl(Pph₃)₃) was used as catalyst. The efficiency on the conjugation of catalyst RhCl (Pph₃)₃, tin dichloride dehydrate (SnCl₂·2H₂O) and triphenylphosphine (Pph₃) were evaluated. The results showed when RhCl(Pph₃)₃, SnCl₂·2H₂O and Pph₃ are 9.25, 9.0 and 13.1 mg in 100 g soybean oil respectively, the highest conversion of conjugation achieved 96%. The free radical copolymerization of conjugated soybean oil with acrylonitrile (AN) and dicyclopentadiene (DCP) was studied. AIBN was used as the initiator. FT-IR and ¹H-NMR results indicates that the conjugated soybean oil with AN and DCP did occur free radical copolymerization with the initiator AIBN. The product is light yellow powder. The thermal properties of the soy-based copolymer were investigated by TG and DSC. The initial degradation temperature of polymers is higher then 250 °C.     

Optimization of Carbon Dioxide and Valeric Acid Utilization for Polyhydroxyalkanoates Synthesis by Cupriavidus necator

The utilization of captured CO₂ as a part of the CO₂ capture and storage system to produce biopolymers could address current environmental issues such as global warming and depletion of resources. In this study, the effect of feeding strategies of CO₂ and valeric acid on cell growth and synthesis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] in Cupriavidus necator was investigated to determine the optimal conditions for microbial growth and biopolymer accumulation. Among the studied CO₂ concentrations (1–20 %), microbial growth and poly(3-hydroxybutyrate) accumulation were optimal at 1 % CO₂ using a gas mixture at H₂:O₂:N₂ = 7:1:91 % (v/v). When valeric acid was fed together with 1 % CO₂, (R)-3-hydroxyvalerate synthesis increased with increasing valeric acid concentration up to 0.1 %, but (R)-3-hydroxybutyrate synthesis was inhibited at >0.05 % valeric acid. Sequential addition of valeric acid (0.05 % at Day 0 followed by 0.025 % at Day 2) showed an increase in 3HV fraction without inhibitory effects on 3HB synthesis during 4 d accumulation period. The resulting P(3HB-co-3HV) with 17–32 mol  % of 3HV is likely to be biocompatible. The optimal concentrations and feeding strategies of CO₂ and valeric acid determined in this study for microbial P(3HB-co-3HV) synthesis can be used to produce biocompatible P(3HB-co-3HV).     

Recovery of yttrium from fluorescent powder of cathode ray tube,CRT: Zn removal by sulphide precipitation

This work is focused on the recovery of yttrium and zinc from fluorescent powder of cathode ray tube (CRT). Metals are extracted by sulphuric acid in the presence of hydrogen peroxide. Leaching tests are carried out according to a 2² full factorial plan and the highest extraction yields for yttrium and zinc equal to 100% are observed under the following conditions: 3 M of sulphuric acid, 10% v/v of H₂O₂ concentrated solution at 30% v/v, 10% w/w pulp density, 70 °C and 3 h of reaction.Two series of precipitation tests for zinc are carried out: a 2² full factorial design and a completely randomized factorial design. In these series the factors investigated are pH of solution during the precipitation and the amount of sodium sulphide added to precipitate zinc sulphide. The data of these tests are used to describe two empirical mathematical models for zinc and yttrium precipitation yields by regression analysis. The highest precipitation yields for zinc are obtained under the following conditions: pH equal to 2–2.5% and 10–12% v/v of Na₂S concentrated solution at 10% w/v. In these conditions the coprecipitation of yttrium is of 15–20%.Finally further yttrium precipitation experiments by oxalic acid on the residual solutions, after removing of zinc, show that yttrium could be recovered and calcined to obtain the final product as yttrium oxide. The achieved results allow to propose a CRT recycling process based on leaching of fluorescent powder from cathode ray tube and recovery of yttrium oxide after removing of zinc by precipitation. The final recovery of yttrium is 75–80%.     

Experimental and numerical calculations of waste R-134a thermal decomposition for energy and fluorine material recovery

Considering the global warming potential of R-134a (C₂H₂F₄) with the substantial generation of this refrigerant as waste material in various industrial sectors, the development of proper thermal destruction method of R-134a is of great practical significance. For this, experiment and numerical calculations have initially made for a tubular-type furnace in order to figure out the basic combustion characteristics of R-134a. A series of experimental investigations for the thermal decomposition of R-134a have been made as a function of wall temperature of tubular furnace and important reacting species such as O₂ and H₂O necessary for the decomposition of C₂H₂F₄ into HF, CO₂ and H₂O. In general, the thermal decomposition of R-134a is successfully made for the condition of temperature above 800 °C with the supply of stoichiometric amount of O₂ and these results are well agreed with numerical prediction. And this information is employed for the simulation of a full-scale, practical incinerator used for the CDM project. For this, numerical investigation has been made for a commercial-scale incinerator using CH₄–air flames for the proper destruction C₂H₂F₄ together with the control of pollutants such as CO and NO. In general, the destruction rate of C₂H₂F₄ appears more than 99.99 % and the generation of CO and NO species appears rather sensitive to the operational condition such as amount of water vapor. The numerical method of HFCs (hydrofluorocarbons) thermal treatment shows high possibility as a viable tool for the proper design and optimal determination of the operational condition for a HFCs incinerator.     

Treatment of Stormwater using Fibre Filter Media

In this study, a high-rate fibre filter was used as a pre-treatment to stormwater in conjunction with in-line flocculation. The effect of operating the fibre filter with different packing densities (105, 115 and 125 kg/m³) and filtration velocities (20, 40, 60 m/h) with and without in-line flocculation was investigated. In-line flocculation was provided using 5, 10 and 15 mg/L of ferric chloride (FeCl₃·6H₂O). The filter performance was studied in terms of pressure drop (ΔP), solids removal efficiency, heavy metals (total) removal efficiency and total organic carbon (TOC) removal efficiency. It is found that the use of in-line flocculation at a dose of 15 mg/L improved the performance of fibre filter as measured by turbidity removal (95%), total suspended solids reduction (98%), colour removal efficiency (99%), TOC removal (reduced by 30–40 %) and total coliform removal (93%). The modified fouling index reduced from 750–950 to 12 s/L² proving that fibre filter can be an excellent pre-treatment to membrane filtration that may be consider as post-treatment. The removal efficiency of heavy metal was variable as their concentration in raw water was small. Even though the concentration of some of these metals such as iron, aluminium, copper and zinc were reduced, others like nickel, chromium and cadmium showed lower removal rates.     

Mechanochemical dechlorination of polyvinyl chloride with calcium sulfates

Polyvinyl chloride (PVC) was milled with hydrated or unhydrated calcium sulfates (CaSO₄·2H₂O or CaSO₄) in air by using a planetary mill to investigate mechanochemical dechlorination behavior. The milling process resulted in size reduction and in the breaking of bonds leading to mechanically induced solid state reaction, forming CaCl₂ and dechlorinated hydrocarbon with C=C double bonds in the product. Washing the milled mixtures with water at room temperature allowed removal of the chloride formed during milling, and more than 95% of the chlorine in PVC was removed from a mixture milled for 4 h. This process could offer a potential route for the handling and disposal of both PVC and gypsum wastes. H₂S gas was generated during milling; more H₂S was released from the unhydrated sample than from the hydrated sample.     

Phosphate recovery from phosphorus-rich solution obtained from chicken manure incineration ash

The recovery of phosphorus from waste is very important for Japan because Japan has no natural phosphorus resources. In order to recover phosphorus from incineration ash of chicken manure, an acid dissolution–alkali precipitation method was investigated. Phosphorus content in the ash was 8%. The ash was treated with hydrochloric acid to obtain phosphorus-rich solution. Phosphorus could then be recovered as a precipitant by adding sodium hydroxide solution into the phosphorus-rich solution and gradually changing the pH in the solution to 3, 4, and 8. At pH 3, a small amount of phosphorus was precipitated to remove iron, which would cause coloring of subsequent precipitants. At pH 4, 84% of the phosphorus in the original solution could be recovered as CaHPO₄ · 2H₂O with a purity of 92%. At pH 8, 8% of the phosphorus in the phosphorus-rich solution could be recovered as identified hydroxyapatite. A recovery rate of 92% phosphorus as CaHPO₄ · 2H₂O and identified as hydroxyapatite was achieved.     

Recovery of Nd and Dy from rare earth magnetic waste sludge by hydrometallurgical process

This paper describes a hydrometallurgical process for recovering neodymium (Nd) and dysprosium (Dy) from a magnetic waste sludge generated from the Nd–Fe–B(–Dy) manufacturing process. Phase analysis by XRD study revealed Nd(OH)₃ and Fe₂O₃ as main mineral phases, and chemical analysis by ICP showed the contents of 35.1 wt% Nd, 29.5 wt% Fe, 1.1 wt% Dy and 0.5 wt% B. A solution of 1 M HNO₃ + 0.3 M H₂O₂ was used to dissolve up to 98 % Nd and 81 % Dy, while keeping Fe dissolution below 15 % within 10 min. Fe dissolved in solution was completely removed as Fe(OH)₃ at pH 3 followed by precipitation of Nd and Dy with oxalic acid (H₂C₂O₄) and recovered 91.5 % of Nd and 81.8 % of Dy from solution. The precipitate containing Nd and Dy was calcined at 800 °C to obtain Nd₂O₃ as final product with 68 % purity, and final recovery of 69.7 % Nd and 51 % of Dy was reported in this process.     

The behaviors of H2, CH4, C2H4 and C3H6 from the decomposition of polypropylene by NiO/Si–Al catalyst

The purpose of this study was to investigate the possibility of light gases produced from polypropylene, specifically hydrogen. In particular, we examined the effect of operating conditions on gaseous product and compositions in the catalytic cracking of polypropylene. We also characterized the gaseous product generated from polypropylene cracking. The feedstock (2.0 g) mixed with NiO/SiO₂–Al₂O₃ (Si–Al) was used, under non-isothermal conditions at low temperature range between 380 and 500 °C. Argon gas was used to carry the pyrolyzed gas, and the gas collected in a tedlar bag was analyzed for its behavior. We observed the behavior of major gases (H₂, CH₄, C₂H₄ and C₃H₆, etc.) according to reaction time and temperature. Finally, the effect of reaction conditions on evolved gases from catalytic cracking of polypropylene was analyzed.     

Stabilization of sewage sludge in the presence of nanoscale zero-valent iron (nZVI): abatement of odor and improvement of biogas production

The potential benefits of nanoscale zero-valent iron (nZVI) on sludge stabilization, either the abatement of odor or the improvement of biogas production, were investigated in this study. Two commercial-grade microscale iron powders were also utilized for comparison. Adding 0.10 wt% of nZVI in sludge during anaerobic incubation significantly reduced the concentration of H₂S in biogas by 98.0 % (96.2–98.9 %), probably attributed by reactions between sulfides and the neo-formed hydrous Fe(II)/Fe(III) oxides layer at the surface of ZVI nanoparticles. Meanwhile, the percentage of P in bioavailable fractions decreased from 76.8 to 52.5 %, possibly due to the formation of vivianite [Fe₃(PO₄)₂]. Furthermore, 0.10 wt% of nZVI in anaerobic digestion for 17 days enhanced the concentration of CH₄ in biogas by 5.1–13.2 % and improved the production of biogas and methane by 30.4 and 40.4 %, respectively. The amendment of iron nanoparticles during anaerobic digestion can not only effectively reduce H₂S in biogas, but also potentially boost methane production significantly.     

Effect of MgO and CaO/SiO2 on the immobilization of chromium in synthetic slags

This work investigated the chemical and mineralogical properties of CaO–SiO₂–Cr₂O₃–CaF₂–MgO slags. Synthetic slags were prepared and the effect of the slag basicity (mass ratio CaO/SiO₂) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by X-ray powder diffraction (XRD) and scanning electron microscope-energy dispersive spectroscopy (SEM–EDS), whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO₂?=?1, the main Cr-compound was MgCr₂O₄ spinel, which forms octahedron crystals. Small amounts of CaCr₂O₄ and CaCrO₄ were also observed. It was found that with increasing the slag basicity from 1 to 2 the compounds MgCr₂O₄ and CaCr₂O₄ were formed together with the Cr(V)-containing compound complex Ca₅(CrO₄)₃F which forms hexagonal crystals. The results showed that the highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO₂?=?2, probably owing to the formation of CaCrO₄ and Ca₅(CrO₄)₃F, whilst the lowest chromium concentration levels corresponded to MgO-based slags owing to the stable binding of chromium in spinel with MgO. Additionally, potential–pH diagrams for the Ca–Cr–H₂O and Mg–Cr–H₂O systems at 25?°C were calculated.     

Polychloroprene Degradation by Photo-Fenton. Conductivity Measures as New Approach for Detecting/Evaluation of Degradation Products

In the present work the photo-degradation of polychloroprene (PCP) in toluene solution catalyzed by FeCl₃·6H₂O and polychromatic light was investigated based on FTIR and ¹³C NMR spectroscopies, on conductivity measurements and DSC technique. The band in the 1700–1790 cm⁻¹ range in the FTIR spectrum characterized the presence of carbonyl products due to the degradation of the PCP on the solution exposed to polychromatic light. The formation of carbonyl on degraded PCP was confirmed by the presence of signal on ¹³C NMR at δ 203.5. Products of PCP degradation, such as acid chlorides, generated in the toluene solution migrate to the aqueous phase (in contact with toluene phase) and the conductivity of aqueous phase increased as the time is elapsed. The area related to the PCP melting-peak on the DSC (film casted after the PCP-FeCl₃·6H₂O toluene solution has been exposed to polychromatic light) significantly decreased in comparison to that in the DSC of the raw PCP cast film.     

Arsenic Removal from Dilute Solutions by High Surface Area Mesoporous Iron Oxyhydroxide

Mesostructured iron oxyhydroxide (FeO _x ) and iron oxyhydroxide–phosphate (FeO _x P) composites were organized using dodecylsulfate surfactant as a template. X-ray diffraction studies depicted a lamellar structure of the product. Ion exchange and solvent extraction methods were employed for the removal of the surfactant. Carboxylate ions exchanged lamellar type mesostructured material reorganized to a wormhole-like mesoporous material when heated under N₂ atmosphere. Surfactant was completely removed by carboxylate ions as observed by the Fourier transform infrared spectra. High surface area acetate-exchanged FeO _x (230 m² g^?1) was obtained after the surfactant removal from the composite (2.8 m² g^?1). Surface area of acetate-exchanged FeO _x P was the highest (240 m²g^?1) after the removal of the surfactant. Local structure of iron species of FeO _x was investigated by X-ray absorption fine structure spectroscopy. Further, Fe···Fe bond appeared at 3.21–3.25 Å with coordination number 2–3, showing a high degree of un-saturation of Fe···Fe bonds. As compared with bulk iron oxyhydroxide and iron-intercalated montmorillonite, the mesoporous iron materials were highly effective for arsenic removal from low concentrations of aqueous solutions. Furthermore, mesoporous iron materials were stable in aqueous phase.