Removal of Pb(II) ions from aqueous solution using activated tea waste: Adsorption on a fixed-bed column

An inexpensive and effective adsorbent was developed from waste tea leaves for the dynamic uptake of Pb(II). Characterization of the adsorbents showed a clear change between physico-chemical properties of activated tea waste and simply tea waste. The purpose of this work was to evaluate the potential of activated tea waste in continuous flow removal of Pb(II) ions from synthetic aqueous effluents. The performance of the system was evaluated to assess the effect of various process variables, viz., of bed height, hydraulic loading rate and initial feed concentration on breakthrough time and adsorption capacity. The shape of the breakthrough curves was determined for the adsorption of Pb(II) by varying different operating parameters like hydraulic loading rate (2.3–9.17 m³/h m²), bed height (0.3–0.5 m) and feed concentration (2–10 mg/l). An attempt has also been made to model the data generated from column studies using the empirical relationship based on the Bohart–Adams model. There was an acceptable degree of agreement between the data for breakthrough time calculated from the Bohart–Adams model and the present experimental study with average absolute deviation of less than 5.0%. The activated tea waste in this study showed very good promise as compared with the other adsorbents available in the literature. The adsorbent could be suitable for repeated use (for more than four cycles) without noticeable loss of capacity.     

Removal of direct red 12B and methylene blue from water by adsorption onto Fe (III)/Cr (III) hydroxide, an industrial solid waste

Removal of direct red 12B and methylene blue by adsorption onto Fe (III)/Cr (III) hydroxide was studied using various parameters such as agitation time, dye concentration, adsorbent dose and pH. Equilibrium adsorption data followed both Langmuir and Freundlich isotherms. Adsorption followed second-order rate kinetics. The Langmuir adsorption capacity (Qo) was found to be 5.0 and 22.8 mg dye per g of the adsorbent for direct red 12B and methylene blue, respectively. Acidic pH was favorable for the adsorption of direct red 12B and basic pH for methylene blue. Desorption studies showed that chemisorption seems to be the major mode of adsorption.     

Application of surface molecular imprinting adsorbent in expanded bed for the adsorption of Ni(2+) and adsorption model

A new surface molecular imprinting adsorbent (SMIA) was used in an expanded bed. The expansion ratio and adsorption performance were studied at different volumetric rates, inlet concentrations, and pH values. A model based on the Adams-Bohart adsorption model of breakthrough curves was established. The predicted curves had good agreement with the experimental curves. The breakthrough time (T(1/2)) decreased with increasing inlet concentration when the outlet concentration was half the initial concentration (C/C(0)=0.5). The inlet concentration had little effect on the adsorption rate constant (k(1)) value when the initial concentration (C(0)) was above 150 mg/L. However, T(1/2) values increased with increasing initial pH of the inlet solution, and the k(1) value decreased due to the competition between H(+) and Ni(2+).     

Green coconut shells applied as adsorbent for removal of toxic metal ions using fixed-bed column technology

This study applies green coconut shells as adsorbent for the removal of toxic metal ions from aqueous effluents using column adsorption. The results show that a flow rate of 2 mL/min and a bed height of 10 cm are most feasible. Furthermore, larger amounts of effluent can be treated for removal of single ions. The breakthrough curves for multiple elements gave the order of adsorption capacity: Cu⁺² > Pb⁺² > Cd⁺² > Zn⁺² > Ni⁺². Real samples arising from the electroplating industry can be efficiently handled.     

Biosorption of Reactive Black 5 from aqueous solutions by chitosan: Column studies

Fixed-bed column studies were carried out to investigate the dynamic sorption of Reactive Black 5 (RB5) onto chitosan. The effect of operating parameters such as initial dye concentration, superficial flow velocity, bed height and particle size on the sorption of RB5 onto chitosan was studied. Column regeneration, dye recovery and the possibility of reusing the regenerated chitosan were also investigated. The results show that both the breakthrough curves and the adsorption parameters of the column were strongly affected by the operating parameters studied. An analysis of the breakthrough curves indicated that adsorption was affected by mass transfer limitations, probably due to intraparticle diffusion. An empirical model was applied to describe the breakthrough curves, while the Bohart–Adams and BDST models were used to determine the operating parameters useful in the process design. Elution of the column with 0.01 mol L^?1 NaOH allowed the chitosan to be regenerated and the dye to be recovered and concentrated. The concentration factor was 10. Several cycles of adsorption–elution showed that the regenerated chitosan retained good adsorption efficiency and the elution efficiency was always higher than 80%.     

Mechanisms and chemistry of dye adsorption on manganese oxides-modified diatomite

The investigations into structural changes which occur during adsorbent modification and the adsorption mechanisms are essential for an effective design of adsorption systems. Manganese oxides were impregnated onto diatomite to form the type known as δ-birnessite. Initial investigations established the effectiveness of manganese oxides-modified diatomite (MOMD) to remove basic and reactive dyes from aqueous solution. The adsorption capacity of MOMD for methylene blue (MB), hydrolysed reactive black (RB) and hydrolysed reactive yellow (RY) was 320, 419, and 204 mg/g, respectively. Various analytical techniques were used to characterise the structure and the mechanisms of the dye adsorption process onto MOMD such as Fourier transform infrared (FTIR), X-ray diffraction (XRD) and atomic absorption spectrometry (A.A.). A small shift to higher values of the d-spacing of dye/MOMD was observed indicating that a small amount of the dye molecules were intercalated in the MOMD structure and other molecules were adsorbed on the external surface of MOMD. Two mechanisms of dye adsorption onto MOMD were proposed; intercalation of the dye in the octahedral layers and adsorption of the dye on the MOMD external surface. Moreover, the results demonstrated that the MOMD structure was changed upon insertion of MB and RY with an obvious decrease in the intensity of the second main peak of the MOMD X-ray pattern.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Optimization of the continuous biosorption of copper with sugar-beet pectin gels

Sugar-beet pectin xerogels obtained from residues of the sugar industry are an adequate material for metal recovery from effluents in continuous systems. The xerogels were used as a biosorbent for copper removal in a fixed-bed column. The performance of the system was evaluated in different experimental conditions: flow rate, bed height, inlet metal concentration and feeding system (drop and reverse). The effect on the biosorption parameters (saturation time, amount of adsorbed and treated metal, column performance and metal uptake) and the shape of the breakthrough curves was determined. The saturation time increased with increasing bed height but decreased with increasing feed flow rate and inlet metal concentration. Preferential flow channels greatly influenced the metal uptake and column performance. Copper was completely desorbed with 0.1 M HNO₃. Additionally, the column data fitted both the linear and nonlinear expressions of the Thomas model.     

A two stage batch adsorber design for methylene blue removal to minimize contact time

The adsorption of methylene blue onto bentonite in a batch adsorber has been studied. Three kinetic models, the intraparticle diffusion equation and the pseudo first and second order equations, were selected to follow the adsorption process. Kinetic parameters, rate constants, equilibrium adsorption capacities and related correlation coefficients for each kinetic model were calculated and discussed. It was shown that the adsorption of methylene blue onto bentonite could be described by the pseudo second order equation. Adsorption of methylene blue onto bentonite followed the Langmuir isotherm. A model has been developed for the design of a two stage batch adsorber based on pseudo second order adsorption kinetics. The model has been optimized with respect to operating time in order to minimize total contact time to achieve a specified amount of methylene blue removal using a fixed mass of adsorbent. The results of two stage batch adsorber design studies showed that the required times for specified amounts of methylene blue removal significantly decreased. This design is particularly suitable for low-cost adsorbents/adsorption systems when minimising contact time is a major operational and design criterion and a significant volume of effluent needs to be treated in the minimum amount of time.     

Adsorption studies of hazardous malachite green onto treated ginger waste

Adsorption of malachite green (MG) from aqueous solution onto treated ginger waste (TGW) was investigated by batch and column methods. The effect of various factors such as initial dye concentration, contact time, pH and temperature were studied. The maximum adsorption of MG was observed at pH 9. Langmuir and Freundlich isotherms were employed to describe the MG adsorption equilibrium. The monolayer adsorption capacities were found to be 84.03, 163.9 and 188.6 mg/g at 30, 40 and 50 °C, respectively. The values of thermodynamic parameters like ΔG°, ΔH° and ΔS° indicated that adsorption was spontaneous and endothermic in nature. The pseudo second order kinetic model fitted well in correlation to the experimental results. Rechienberg's equation was employed to determine the mechanism of adsorption. The results indicated that film diffusion was a major mode of adsorption. The breakthrough capacities were also investigated.     

Treatment and toxicity evaluation of methylene blue using electrochemical oxidation,fly ash adsorption and combined electrochemical oxidation-fly ash adsorption

Treatment of a basic dye, methylene blue, by electrochemical oxidation, fly ash adsorption, and combined electrochemical oxidation-fly ash adsorption was compared. Methylene blue at 100 mg L^?1 was used in this study. The toxicity was also monitored by the Vibrio fischeri light inhibition test.When electrochemical oxidation was used, 99% color and 84% COD were removed from the methylene blue solution in 20 min at a current density of 428 A m^?2, NaCl of 1000 mg L^?1, and pH₀ of 7. However, the decolorized solution showed high toxicity (100% light inhibition).For fly ash adsorption, a high dose of fly ash (>20,000 mg L^?1) was needed to remove methylene blue, and the Freundlich isotherm described the adsorption behavior well.In the combined electrochemical oxidation-fly ash adsorption treatment, the addition of 4000 mg L^?1 fly ash effectively reduced intermediate toxicity and decreased the COD of the electrochemical oxidation-treated methylene blue solution. The results indicated that the combined process effectively removed color, COD, and intermediate toxicity of the methylene blue solution.     

Preparation of activated carbons from unburnt coal in bottom ash with KOH activation for liquid-phase adsorption

In this work, unburnt coal (UC) in bottom ash from coal-fired power plants was soaked in KOH solution and activated for 1 h at 780 °C. The yield of activated carbons varied from 47.8 to 54.8% when the KOH/UC weight ratio changed from 2 to 4. Pore properties of these activated carbons including the BET surface area, pore volume, pore size distribution, and pore diameter were characterized based on N₂ adsorption isotherms. It was shown that the isotherms for the adsorption of methylene blue, acid blue 74, and 4-chlorophenol from aqueous solutions on these activated carbons at 30 °C were well fitted by the Langmuir equation (correlation coefficient r² > 0.9968). The adsorption capacities of methylene blue, acid blue 74, and 4-chlorophenol were obtained to be 2.40–2.88, 0.57–1.29, and 2.34–5.62 mmol/g, respectively. Moreover, the adsorption kinetics could be suitably described by the Elovich equation.     

Loofa egyptiaca as a novel adsorbent for removal of direct blue dye from aqueous solution

In this paper, Loofa egyptiaca (LE), an agricultural plant cultivated in Egypt, was used to prepare low-cost activated carbon (LE_C1 and LE_C2) adsorbents. The adsorbents (LE, LE_C1 and LE_C2) were evaluated for their ability to remove direct blue 106 dye from aqueous solutions. Batch mode experiments were conducted using various parameters such as pH, contact time, dye concentration and adsorbent concentration. The surface chemistry of LE, LE_C1 and LE_C2 was analyzed by scanning electron microscopy (SEM). The experimental data were examined using Langmuir, Freundlich, Temkin and Harkins–Jura isotherms. The results showed that the adsorption of direct blue 106 was maximal at the lowest value of pH (pH = 2). Removal efficiency was increased with an increase in dye concentration and a decrease in amount of adsorbent. Maximum adsorption capacity was found to be 57.14, 63.3 and 73.53 mg/g for LE, LE_C1 and LE_C2 respectively. Kinetics were also investigated using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The experimental data fitted very well with the pseudo-first-order and pseudo-second-order kinetic models. The results indicate that LE, LE_C1 and LE_C2 could be employed as adsorbents for the removal of direct blue dye from aqueous solutions.     

草木灰对亚甲基蓝的吸附研究

本实验目的是研究草木灰对吸附亚甲基蓝的去除效果,探讨了亚甲基蓝初始量、吸附时间、pH值等对吸附效果的影响,并运用伪一级、伪二级反应动力学模型和Laugmuir、Freundlich等温线模型进行拟合。结果表明,草木灰对亚甲基蓝溶液的吸附在5 min~30 min速率比较快,约在65 min内达到吸附平衡,pH越大越有利于吸附,浓度在5mg/L时草木灰对亚甲基蓝的吸附最佳。与伪二级动力学曲线模型拟合效果较好,由Laugmuir等温线模型计算得出理论最大吸附容量Qm为2.275 mg/g,吸附性能优异。     

Lead removal from contaminated water using mineral adsorbents

This study records experiments undertaken to determine the suitable conditions for the use of naturally occurring minerals (talc, chalcopyrite and barite) as an adsorbent for the removal of lead ions from liquid wastes. The adsorption of lead ions from solutions containing different initial lead concentrations (50, 100, 200, 400, 600, 800 and 1000 mg l^–1 Pb as lead nitrate) using different size fractions (<63 m, 63–150 m) of talc, chalcopyrite and barite at different pH (3, 5, 7 and 9) and different adsorption times (24, 48, 72 and 96 hr) was examined. The results revealed that of the studied minerals, the chalcopyrite fraction at 63–150 m showed the highest adsorption capacity. The adsorption data of Pb ions was also analyzed with the help of the Langmuir and Freundlich models to evaluate the mechanistic parameters associated with the adsorption process. The adsorption isotherms obtained from the Langmuir and Freundlich equations were generally linear and the adsorption of Pb by the studied minerals was correlated with the adsorption maximum and binding energy constant of the Langmuir equation and equilibrium partition constant and binding partition coefficient of the Freundlich equation. It was concluded that the equilibrium time of adsorption was 72 hr at an optimum pH from 7 to 9. This technique might be successfully used for the removal of lead ions from liquid industrial wastes and wastewater.     

树脂固定床吸附含酚废水预测模型研究

针对应用于实际工业化的树脂固定床吸附研究较少,而与之相关的固定床吸附穿透曲线可以用来确定固定床吸附操作参数,为固定床的设计和实际操作提供指导。通过对恒定波振荡理论和吸附等温方程的联合,来预测固定床吸附穿透曲线;并研究了不同操作条件对大孔弱碱树脂吸附对硝基酚穿透曲线预测模型的影响。以期望为树脂固定床的设计和实际工业应用产生指导意义。     

Phenol removal from aqueous environments by natural & chemically modified kaolin clay

Natural, acid and base modified kaolin clays were studied for the sake of phenol and 4-chlorophenol removal from aqueous environments and their application to real ground and industrial wastewater samples. Scanning electron microscope (SEM), infrared spectroscopy (IR), X-ray diffraction (XRD), Thermo Gravimetric Analysis (TGA), Differential Thermal Analysis (DTA), and Surface area analysis were employed for characterization of the adsorbents microstructure. Operating factors such as adsorbent dose, solution pH, initial phenol concentration, and contact time were studied. The experimental data displayed that the increase of the adsorbent dose, contact time, and pH value from 2 to 7 increases the efficiency of the removal process. Optimal conditions for phenolic removal were; contact time of 300 min, primary phenol solution of 25 mg/L, pH 7 and 2.5 g/L as an appropriate adsorbent dose using crude (natural), acid modified and base modified kaolin clays. The higher phenolic removal efficiencies were obtained at 5 mg/L as 90, 97, 96.2%, respectively, for the adsorbents in the previously mentioned order. The adsorption capacity in the removal of phenol and 4-chlorophenol were 7.481 and 4.195, 8.2942 and 3.211, and 8.05185 and 18.565 mg/g, respectively, for the adsorbents in the same mentioned order. The adsorption equilibrium data were fitted and analyzed with four isotherm models, namely, Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm equations. The adsorption process of phenol on studied adsorbents was exothermic, spontaneous and thermodynamically favorable proved by the negative values of their thermodynamic parameters ΔH° and ΔG°. The correlation coefficient (R²) for all concentrations was higher than 0.94, which indicates that in the studied system, the data suitably fit the first-order kinetics. The % desorption capacity was amounted to 96%, 91.11%, and 87.06% of adsorbed phenol, respectively, for the adsorbents in the previous order using 0.1N NaOH and 10% V/V ethanol solutions as eluents at 25°C, indicating the reusability of the adsorbents. Kaolin and its modified forms can be introduced as eco-friendly and low-cost adsorbents in water remediation implementation.     

Platinum (IV) recovery from chloride solution by functionalized acrylic copolymers

Two acrylic adsorbents with different morphological structures and bearing amidoethylenamine and thiol groups were obtained and used for platinum sorption from chloride solution by the batch method. Physico-chemical parameters that influence adsorption such as initial Pt(IV) concentration, stirring time, pH, and adsorbent amount were investigated. The thermodynamic parameters of Pt(IV) sorption on the synthesized adsorbent were also evaluated based on Langmuir and Freundlich isotherms. Thermodynamic parameters estimated from Langmuir constants indicated that the adsorption is spontaneous, exothermic and there is a disordered state at the molecular level. The models used to analyze the sorption rate led to the conclusion that the most important step in the sorption of Pt(IV) could be both particle diffusion and chemical reaction of [PtCl₆]⁻ with amine functional groups. Thus, both the ion exchange and complex formation mechanisms can occur via nitrogen atoms in the recovery of Pt(IV) on the studied adsorbent.     

Fly ash for the treatment of Zn(II) rich effluents

Summary The ability of fly ash to remove Zn(II) from water by adsorption has been tested at different concentrations, temperatures and pH of the solution. It was found that low adsorbate concentration, small particle size of adsorbent and higher temperature favoured the removal of Zn(II) from aqueous solution. The Langmuir isotherm was used to represent the equilibrium data at different temperatures. The apparent heat of adsorption has been found to be 17.325 Kcal mol^–1, which indicates the process to be endothermic. The uptake of Zn(II) is diffusion controlled and the mass transfer coefficient is 3.56 × 10^–5 cm s ^–1.The maximum removal was noted at pH 7.5. Dr V.N. Singh is Professor and Head of the Department of Applied Chemistry, Dr A.K. and Prof. D.P. Singh are members of the Department of Mining Engineering; all are situated in the Institute of Technology at Banaras Hindu University.     

Adsorption of basic dye from aqueous solution onto fly ash

The fly ash treated by H₂SO₄ was used as a low-cost adsorbent for the removal of a typical dye, methylene blue, from aqueous solution. An increase in the specific surface area and dye-adsorption capacity was observed after the acid treatment. The adsorption isotherm and kinetics of the treated fly ash were studied. The experimental results were fitted using Langmuir and Freundlich isotherms. It shows that the Freundlich isotherm is better in describing the adsorption process. Two kinetic models, pseudo-first order and pseudo-second order, were employed to analyze the kinetic data. It was found that the pseudo-second-order model is the better choice to describe the adsorption behavior. The thermodynamic study reveals that the enthalpy (ΔH⁰) value is positive (5.63 kJ/mol), suggesting an endothermic nature of the adsorption.