树脂吸附法处理分散蓝NKF脱磺母液

对NDA－9大孔吸附树脂吸附法处理分散蓝NKF生产过程中产生的脱磺母液（废水）进行了研究。在试验条件下，废水经吸附处理后COD由7500mg/L以上降至700mg/L以下，去除率达90％以上，树脂的脱附率大于98％。吸附出水经Fenton试剂氧化处理后，出水COD降至100mg/L以下，去除率达98％以上。     

苯基周位酸生产废水处理试验研究

采用CHA－111大孔吸附树脂对苯基周位酸生产过程排放的汽提苯胺盐析废水和苯基周位酸酸析母液进行处理试验,效果良好。汽提苯胺盐析废水苯胺质量浓度＞1600mg／L,经树脂吸附处理后苯胺质量浓度＜2mg／L,苯胺去除率＞99．9％,COD去除率＞97％,树脂工作吸附量达120g／L,脱附率＞98％;苯基周位酸酸析母液经树脂吸附、混凝沉淀处理后,苯基周位酸质量浓度＜190mg／L,苯基周位酸去除率为94．8％,COD去除率为94．3％,氨基值去除率为80％,脱附率＞99％。     

HZ-16型大孔树脂吸附处理含RDT-8废水

采用HZ-16型大孔树脂对含三（三溴苯氧基）三嗪（RDT-8）废水进行吸附及脱附处理。实验结果表明：在废水流量为4.0 BV/h的条件下，树脂最佳吸附工艺条件为出水体积88.0 BV，此条件下出水COD小于291 mg/L，挥发酚质量浓度小于0.08 mg/L；在脱附液流量为0.5 BV/h的条件下，树脂最佳脱附工艺条件为脱附液体积3.0 BV，此条件下脱附液中挥发酚质量浓度为30.6 mg/L，挥发酚脱附率高达76.4%。在最佳吸附-脱附工艺条件下，连续进行10次动态吸附-脱附实验，吸附出水中COD为137~294 mg/L，COD去除率为72.5%~89.1%，挥发酚质量浓度稳定在0.05 mg/L以下，挥发酚去除率为99.8%~100%，说明HZ-16型大孔树脂的吸附-脱附性能稳定。     

树脂吸附-Fenton试剂氧化法处理水杨醛生产废水

采用树脂吸附-Fenton试剂氧化法处理水杨醛生产废水。XF-01树脂和XF-02树脂静态吸附水杨醛生产废水时，COD去除率均在85％以上，挥发酚去除率均高于90％。XF-02树脂对水杨醛生产废水的处理效果更佳。动态吸附随废水流量增大，吸附出水的COD和挥发酚质量浓度均增加。适宜的废水流量为15BV，树脂的最佳脱附温度为80℃。在连续4批的吸附-脱附实验中，吸附出水的平均COD约为1200mg／L，平均挥发酚质量浓度小于10mg／L。在Fenton试剂氧化中，铁屑和铁粉的催化效果差别很小，都好于FeSO4·7H2O。以铁屑为催化剂、H2O2溶液加入量为1％时，氧化出水的COD小于150mg／L，挥发酚质量浓度小于0．5mg／L。     

大孔树脂吸附—Fenton试剂氧化法预处理含邻苯二甲酸二异丁酯废水

采用大孔树脂吸附—Fenton试剂氧化法预处理含邻苯二甲酸二异丁酯(DIBP)废水。大孔树脂吸附工段的最佳实验条件为:以树脂NDA88为吸附剂,废水pH为2。NDA88经过10批次的连续使用,COD去除率基本稳定在58%左右,脱附率可达96%以上,吸附后废水COD为12 000 mg/L左右。Fenton试剂氧化工段的最佳实验条件为:H2O2加入量70 mL/L,n(H2O2):n(Fe2+)=4,废水pH 4。在此最佳条件下进行实验,Fenton试剂氧化工段COD去除率达65%,处理后废水COD为4 200 mg/L。     

吸附-Fenton氧化-絮凝法处理对硝基苯胺生产废水

采用吸附-Fenton氧化-絮凝法处理对硝基苯胺生产废水(简称废水),研究了吸附剂、脱附温度、絮凝剂等因素对处理效果的影响.经实验确定的最佳工艺条件为:DM301大孔树脂加入量5.0 g/L,吸附时间20 h,Fenton氧化pH 3.0,H_20_2加入量0.3 moL/L,m(Fe):m(H_20_2)=6,絮凝阴离子型聚丙烯酰胺加入量20 mg/L.在此条件下对COD为2 780 mg/L、色度为185倍和pH为12.2的废水进行处理,出水的COD、色度和pH分别为169 mg/L、10倍和6.5,COD去除率和色度去除率分别达到93.9%和94.5%.DM301树脂在10～25次重复使用后对硝基苯胺的平均总去除率为47.7%,对硝基苯胺的平均回收率为37.9%.     

树脂吸附法处理对氨基苯酚废水

采用自制的NDA-99特种复合功能树脂处理对氨基苯酚（PAP）生产废水，考察了各种因素对吸附和脱附效果的影响。小试实验结果得出的工艺条件为：吸附流量2．0BV／h，吸附温度15℃，单柱吸附量10BV；脱附剂为2BV盐酸（质量分数1．5％）＋2BV水。中试试验结果表明，在上述工艺条件下，NDA-99树脂处理PAP废水的吸附性能和脱附性能稳定，平均COD去除率约为93％，平均PAP脱附率达98％。     

树脂吸附法处理硝基苯和硝基氯苯生产废水的研究

研究了用ＣＨＡ－１１１树脂吸附处理硝基本和硝基氯苯生产废水的最佳工艺条件，当废水中硝基苯类化合物含量为６３９ｍｇ／Ｌ时，ＣＨＡ－１１１树脂的工作吸附容量为１２６ｍｇ／ｍＬ，处理水量为１９０ＢＶ，处理后硝苯类化合物的浓度〈５ｍｇ／Ｌ，去除率〉９９％；采用异丙醇作脱附剂；表明该树脂的吸附与脱附性能良好。     

离子交换树脂处理三乙胺废水

采用离子交换树脂对废水中三乙胺进行吸附。探讨了静态及动态吸附三乙胺的影响因素,考察了树脂的脱附条件及其吸附稳定性。实验结果表明:RX01型树脂对三乙胺的吸附性能优于HD-81型和D155型树脂;在三乙胺初始质量浓度为1 500 mg/L、初始pH为11.5、吸附时间为2 h、吸附温度为298 K的静态吸附条件下,三乙胺去除率为96.3%,饱和吸附量为145 mg/g,等浓度条件下阳离子影响的大小顺序为Ca~(2+)Mg~(2+)K~(+)Na~(+);当三乙胺初始质量浓度为1 500 mg/L、废水流量为60 BV/h、动态吸附柱高径比为5.37时,穿透体积为70 BV,出水三乙胺质量浓度小于3 mg/L,三乙胺去除率高达99.5%;以2 mol/L的HCl溶液为脱附剂,脱附剂流量为1 BV/h、出水体积为4 BV时,三乙胺的脱附率达94.8%;在最优动态吸附-脱附条件下重复使用10次,树脂性能稳定。     

活性碳纤维吸附处理对硝基苯酚生产废水

采用活性碳纤维(ACF)吸附处理对硝基苯酚(PNP)生产废水,考察了动态吸附和脱附过程.实验结果表明,在298 K、pH 4时,最佳进水流量为0.25 L/h,ACF的有效吸附量为439.3 mg/g,PNP去除率大于99.95%,TOC去除率大于99.5%,脱附率大于99.5%,ACF的吸附--脱附性能稳定.ACF吸附和电解相结合的工艺能有效去除废水中的有害物质,回收利用PNP和氯化钠,实现了PNP的清洁生产.     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩，馏出液经铁炭氧微电解和混凝预处理，再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下，处理后出水pH6～9，COD 302mg／L，BOD5 108mg／L，SS30mg／L，色度36倍，水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.