Simultaneous nitrification and denitrification with anoxic phosphorus uptake in a membrane bioreactor system.

The performance of an innovative membrane bioreactor (MBR) process using anoxic phosphorus uptake with nitrification and denitrification for the treatment of municipal wastewater with respect to operational performance and effluent quality is addressed in this paper. The system was operated at steady-state conditions with a synthetic acetate-based wastewater at a hydraulic retention time (HRT) of 12 hours and on degritted municipal wastewater at a total system HRT of 6 hours. The MBR system was able to achieve 99% biochemical oxygen demand (BOD), chemical oxygen demand (COD), and ammonia-nitrogen (NH4(+)-N); 98% total Kjeldahl nitrogen (TKN); and 97% phosphorus removal, producing effluent BOD, COD, NH4+-N, TKN, nitrate-nitrogen, nitrite-nitrogen, and phosphate-phosphorus of <3, 14, 0.2, 0.26, 5.8, 0.21, and <0.01 mg/L, respectively, at the 6-hour HRT. The comparison of the synthetic and municipal wastewater run is presented in this paper. Steady-state mass balance on municipal wastewater was performed to reveal some key features of the modified MBR system.     

Treatment of high-strength pet food wastewater using two-stage membrane bioreactors.

A two-stage membrane bioreactor was used to treat dissolved-air-flotation pretreated, high-strength pet food wastewater characterized by oil and grease concentrations of 50 000 to 82 000 mg/L and total chemical oxygen demand (COD) and five-day biochemical oxygen demand (BOD5) concentrations of 100 000 and 80 000 mg/L, respectively, to meet stringent surface discharge criteria (i.e., BOD5, total suspended solids [TSS], and ammonium-nitrogen [NH4(+)-N] of < 10 mg/L at an overall hydraulic retention time of 6.3 days). Organic contaminants were removed primarily in the first stage, followed by almost complete removal of ammonia in the second stage. Despite a rise in poorly biodegradable COD in the second stage, overall removal of TSS, BOD5, COD, and ammonia was 100, 99.9, 95.2, and 99.7%, respectively, thus readily achieving the required criteria. Consistent nitrite accumulation over a period of more than 100 days, even at dissolved oxygen concentrations of more than 2.5 mg/L, was remarkable. A residual alkalinity requirement for nitrification was quantified. Membrane performance was extensively studied in this work.     

Aerobic Treatment of a Nitrogen-Limited Chemical Process Waste water

Abstract

Nitrogen transformations and their effect on aerobic suspended growth treatment of an industrial wastewater were studied in three parallel bench-scale reactors operated at 5 "C at mean cell residence times (MCRT) of 15, 30, and 60 days. In normal process wastewater, the bulk of influent nitrogen was in organic form, and the fraction transformed was almost totally incorporated into synthesized biomass. Assimilative control by heterotrophs maintained ammonianitrogen levels below permitted effluent levels, and nitrification was not significant. Although volatile suspended solids had a nitrogen content of only 5% to 8%, effective organics removal was maintained, and total organic carbon and filtered daily average five-day biochemical oxygen demand (BODS) were below permitted effluent levels. A marked improvement in settleability and lower effluent total suspended solids was achieved by adding ammonia-nitrogen to the wastewater in excess of stoichiometric growth requirements.

During a batch production cycle of a cationic chemical, the ratio of nitrogen to chemical oxygen demand and the fraction of the total influent nitrogen in soluble form increased in the wastewater. Reactor effluent ammonia levels increased to above permit levels at all three MCRTs during treatment of wastewater containing cationic production effluents. The magnitude of ammonia increase was greater for longer MCRTs, suggesting that synthesis of cell mass was not capable of assimilating the increased ammonia supply under these non-steady conditions. The experimental results suggest several potential strategies for operating the aerobic process at the treatment facility, including adding nitrogen to improve settleability and discontinuing these additions when wastewater contains a high ratio of nitrogen to chemical oxygen demand and an elevated soluble nitrogen fraction     

Advanced oxidation treatment of physico-chemically pre-treated olive mill industry effluent

In this study, the applicability of physico-chemical methods was investigated for the pre-treatment of the olive mill effluents prior to the discharge into the common sewerage ending with a municipal wastewater treatment plant. The samples were taken from an olive oil industry operated as three-phase process located in Turkey. Various pre-treatment methods including acid craking, polyelectrolyte and lime additions were applied. Advanced oxidation study using Fenton's process was also investigated following pre-treatment by acid cracking and cationic polyelectrolyte. Acid cracking alone gave satisfactory treatment efficiencies and polyelectrolite additions to the acid-cracked samples enhanced treatment efficiency. Since a complete treatment plant is available at the end of the sewer system, results indicated that the effluents of the investigated industry could be discharged into the municipal sewerage in the case of total chemical oxygen demand (COD_tot), suspended solid (SS) and volatile suspended solid (VSS) concentrations according to the Turkish Water Pollution Control Regulation after pre-treatment with 5 ppm anionic polyelectrolyte following acid cracking. The minimum COD_tot, SS and VSS removals were observed when raw wastewater was pre-treated with lime and the discharge standards to the municipal sewer system could not be met. Advanced oxidation with Fenton's process was applied after acid cracking and cationic polyelectrolyte treatment in order to investigate further reduction in chemical oxygen demand (COD) concentration for minimizing the influence of this industrial discharge on the existing municipal wastewater treatment plant. Results indicated that COD_tot removal increased up to 89% from 74% after Fenton's oxidation for the acid cracked samples in which cationic polyelectrolite (10 ppm) was added.     

Advanced oxidation treatment of physico-chemically pre-treated olive mill industry effluent

In this study, the applicability of physico-chemical methods was investigated for the pre-treatment of the olive mill effluents prior to the discharge into the common sewerage ending with a municipal wastewater treatment plant. The samples were taken from an olive oil industry operated as three-phase process located in Turkey. Various pre-treatment methods including acid craking, polyelectrolyte and lime additions were applied. Advanced oxidation study using Fenton's process was also investigated following pre-treatment by acid cracking and cationic polyelectrolyte. Acid cracking alone gave satisfactory treatment efficiencies and polyelectrolite additions to the acid-cracked samples enhanced treatment efficiency. Since a complete treatment plant is available at the end of the sewer system, results indicated that the effluents of the investigated industry could be discharged into the municipal sewerage in the case of total chemical oxygen demand (COD(tot)), suspended solid (SS) and volatile suspended solid (VSS) concentrations according to the Turkish Water Pollution Control Regulation after pre-treatment with 5 ppm anionic polyelectrolyte following acid cracking. The minimum COD(tot), SS and VSS removals were observed when raw wastewater was pre-treated with lime and the discharge standards to the municipal sewer system could not be met. Advanced oxidation with Fenton's process was applied after acid cracking and cationic polyelectrolyte treatment in order to investigate further reduction in chemical oxygen demand (COD) concentration for minimizing the influence of this industrial discharge on the existing municipal wastewater treatment plant. Results indicated that COD(tot) removal increased up to 89% from 74% after Fenton's oxidation for the acid cracked samples in which cationic polyelectrolite (10 ppm) was added.     

Behaviors of intercellular materials and nutrients in biological nutrient removal process supplied with domestic wastewater and food waste.

A four-stage biological nutrient removal (BNR) process was operated to investigate the effect of anaerobically fermented leachate of food waste (AFLFW) as an external carbon source on nutrient removal from domestic wastewater having a low carbon-to-nitrogen ratio. The BNR system that was supplemented with AFLFW showed a good performance at a sludge retention time (SRT) of 30 days, despite low temperature. With this wastewater, average removal efficiencies of soluble chemical oxygen demand (COD), total nitrogen (T-N), and total phosphorus (T-P) were 88 to 93%, 70 to 74%, and 63 to 68%, respectively. In this study, several kinds of poly-hydroxyalkanoates (PHAs) were observed in cells. These included 24% poly-3-hydroxybutyrate (PHB), 41% poly-3-hydroxyvalerate (PHV), 18% poly-3-hydroxyhexanoate (PHH), 10% poly-3-hydroxyoctanoate (PHO), 5% poly-3-hydroxydecanoate (PHD). and 2% poly-3-hydroxydodecanoate (PHDD), indicating that microorganisms could store various PHAs through the different metabolic pathways. However, breakdown of the enhanced biological phosphorus removal (EBPR) mechanism was observed when SRT increased from 30 to 50 days for the enhancement of nitrification. To study the effect of SRT on EBPR, a sequencing batch reactor (SBR) system that was supplied with glucose was operated at various SRTs of 5, 10, and 15 days. Nitrification and denitrification efficiencies increased as SRT increased. However, the content of intracellular materials such as PHAs, glycogen. and poly-P in cells decreased. From these results, it was concluded that SRT should be carefully controlled to increase nitrification activity and to maintain biological phosphorus removal activity in the BNR process.     

An approach to wastewater treatment in organised industrial districts: a pilot-scale example from Turkey

In this study, a detailed wastewater profile and treatability studies of Demirtas Organized Industrial District (OID) were undertaken on a pilot-scale. The industrial categorisation of Demirtas OID was determined, and the wastewater characterisations of each industrial sector were analysed and the flow-rates were measured. The results were used to design a wastewater treatment plant for Demirtas OID. Pilot-scale chemical and biological treatability studies were carried out. The steady-state performance of the pilot-scale treatment system in removing chemical oxygen demand (COD) and suspended solids (SS) was studied for a period of three months. The removal efficiencies obtained in this study were 42% of COD and 67% of SS in the chemical treatment, and 84% of COD and 25% of SS in the biological treatment. The overall removal efficiency of the pilot-scale system was 91% COD and 75% SS. The pilot-scale study showed that the wastewater from Demirtas OID could be treated with biological and chemical methods, and the treated wastewater met the Regulation of Discharge Standards of Turkey. The significance of this study is that it is the first such system in Turkey to be tested on a pilot scale.     

低C/N比水产养殖废水生物脱氮实验研究

随着短程硝化-反硝化理论研究的发展,在低C/N比条件下,实现污水的生物脱氮处理已成为可能。为此,设计了水产养殖用水的三级生物膜短程硝化-反硝化处理工艺,并对该工艺在去除模拟水产养殖废水主要污染物的作用进行了初步研究。研究结果表明,在进水pH值7.5~8.5,温度为28~32℃,溶解氧为0.5~1 mg/L,游离氨浓度为5~10 mg/L的条件下,模拟废水的COD、NH4+-N和TN的平均去除率分别达到94.4%、91.6%和70.1%;并且低C/N比对出水氨氮NH4+-N的去除率影响不大,NO2--N的平均浓度控制在5.2 mg/L以下,低于鱼类的耐受浓度。表明该短程硝化-反硝化工艺设计,可用于低C/N比水产养殖废水主要污染物的生物处理,尤其是可消除NO2--N对水产养殖的潜在威胁,基本达到养鱼回用标准。     

Adverse effects of erythromycin on the structure and chemistry of activated sludge

This study examines the effects of erythromycin on activated sludge from two French urban wastewater treatment plants (WWTPs). Wastewater spiked with 10 mg/L erythromycin inhibited the specific evolution rate of chemical oxygen demand (COD) by 79% (standard deviation 34%) and the specific N-NH₄⁺ evolution rate by 41% (standard deviation 25%). A temporary increase in COD and tryptophan-like fluorescence, as well as a decrease in suspended solids, were observed in reactors with wastewater containing erythromycin. The destruction of activated sludge flocs was monitored by automated image analysis. The effect of erythromycin on nitrification was variable depending on the sludge origin. Erythromycin inhibited the specific nitrification rate in sludge from one WWTP, but increased the nitrification rate at the other facility.     

生物脱氮工艺控制优化策略的研究进展

针对传统的单污泥生物脱氮系统具有所需反应器体积大、硝化反硝化效率低及对进水COD利用率低等一系列问题 ,总结了提高生物脱氮工艺效率的在线控制策略 ,如曝气控制、外投碳源控制和污泥龄控制 (SRT) ,为当前污水厂在工艺设计一定的限制性条件下进行在线优化以满足日益严格的排放标准提供了重要保证。     

SFBR工艺顺序进行硝化和反硝化的动力学研究

采用序半连续式反应器(sequencing fed-batch reactor,简称SFBR)对人工合成废水顺序地进行硝化和反硝化动力学进行了研究.硝化和反硝化所用微生物为活性污泥.反应器在不同的操作条件进行操作,获得了用于确定动力学常数的数据;获得动力学参数um=0.05 h-1,KNO=2.0 mg/L,y=0.47 mg X/mg N,a=0.001 h-1.类似地确定了反硝化动力学参数kD=0.01 h-1和KD,NO=0.4 mg/L.在一定范围内硝化和反硝化速率随着氨浓度和硝酸盐浓度的增加而增加.实验数据表明,硝化和反硝化的动力学符合Monod动力学方程.     

Microbial activity in a combined UASB-activated sludge reactor system

A combined upflow anaerobic sludge bed-activated sludge (UASB-AS) reactor system with consistently wasting of excess biomass was used to treat suspended-solids pre-settled piggery wastewater (COD=2000 mg l(-1), total Kjeldahl nitrogen TKN=400 mg l(-1), suspended solids=250-400 mg l(-1)). Thus, the activity of nitrogen-related microbial groups in each individual bioreactor was investigated. When the granules retention time (GRT) of 20-50 d in the UASB reactor, the solids retention time (SRT) of 10-25 d in the AS reactor and the recycle-to-influent ratio (Re) of 1 were maintained, the combined system removed 95-97% of chemical oxygen demand (COD), 100% of TKN and 54-55% of total nitrogen (TN). Denitrification and methanogenesis occurred in the UASB reactor so that both biochemical processes contributed to most of the COD removal and, complete nitrification (most of the TKN removal) occurred in the AS reactor. Compact granules with good settling abilities developed in the UASB reactor, and rapid rates of granulation of break-up granules in the UASB reactor were confirmed by experiments. The activity of nitrifiers and denitrifiers (an=0.68-0.87; adn=0.55-0.70) and the calculated specific nitrification and denitrification rates (qn=0.26-0.47 mg NH4+ -N mg VSS(-1)d(-1); qdn=0.046-0.076 mg NOx- -N mg VSS(-1)d(-1)) significantly increased with decreasing SRT and GRT, respectively. Accordingly, the combined UASB-AS reactor system should be regarded a promising alternative for the removal of organic carbon and nitrogen from piggery wastewater.     

Comparison of bioluminescence and nitrification inhibition methods for assessing toxicity to municipal activated sludge

The aim of this study was to compare two alternative toxicity assessment methods to determine wastewater toxicity and predict treatment plant process upsets. The toxicity of two synthetic organic compounds (triclosan and 4-n-nonylphenol), which are commonly detected in municipal wastewater, and municipal and industrial wastewaters with different heavy metals content were evaluated by the nitrification inhibition assay and bioluminescence toxicity test. Comparison between both assays confirmed that Vibrio fischeri is generally more sensitive than autotrophic bacteria, and, if not calibrated, the bioluminescence method tends to overestimate toxic effects on activated sludge biomass. The nitrification inhibition assay appears to predict plant process upsets more accurately. Both methods showed a significant toxicity decrease through treatment that could be partially attributed to the significant heavy metals removal obtained by primary and secondary treatment. A good correlation for the two assays was obtained, as indicated by a high correlation coefficient (r2 = 0.80).     

两级SBR与传统SBR工艺的对比研究

用两级SBR工艺（TSSBR）处理COD与氮浓度较高的工业废水，SBR1去除有机物，SBR2主要进行硝化反硝化。TSSBR与传统SBR工艺相比，COD降解速率和硝化反应速率明显提高，COD去除率由84％提高到93％，2种工艺的反硝化速率没有明显差别。在原水COD浓度较高的情况下，TSSBR可有效克服高COD浓度对硝化反应的抑制，硝化反应速率是传统SBR的2倍。对于COD和氮浓度较高的工业废水，TSSBR明显优于传统SBR，是一种理想的处理工艺。     

低COD/N-NH_4比废水的同时硝化反硝化生物处理策略

从生化反应计量学出发 ,提出了对低 COD/ N- NH4比废水可以通过控制营养配比、调控溶解氧浓度和控制生物硝化及生物反硝化 ,经过 NO- 2 途径进行同时硝化反硝化的生物处理策略。对香港低 COD/ N- NH4比的垃圾渗漏水用同时硝化反硝化处理的成功实例进行了讨论     

一株高效异养硝化-好氧反硝化菌的分离鉴定及脱氮性能

从经驯化的污泥中筛选出一株异养硝化-好氧反硝化细菌，编号为TN-05，通过形态学特征观察，生理生化特征试验和核酸序列分析鉴定其为门多萨假单胞菌（pseudomonasmendocina）。同时对其进行脱氮性能研究，结果表明，TN-05具有较好的异养硝化能力，菌株在培养至48h时对总氮和氨氮去除率均能达95％以上。通过反硝化能力验证实验发现，菌株对NO3-N和N0f—N也分别具有较好的去除效率。将菌株应用于人工合成废水中，发现对废水中氨氮优先利用并能在24h时使去除率接近100％，对硝态氮和亚硝态氮也具有一定的去除效率。因此，菌株TN-05是一株同时具备异养硝化和好氧反硝化能力的高效菌株。     

实际污水与模拟污水活性污泥系统的特性差异

实验中经常采用人工配置的模拟生活污水,为了研究其与实际生活污水活性污泥系统的特性差异,采用2个序批式间歇反应器(SBR)进行平行实验(厌氧、好氧方式运行),系统地考察了在进水主要组分和运行参数相同的情况下,不同原水对活性污泥系统脱氮、除磷、比好氧速率、污泥絮体形态和出水水质等方面的影响。结果表明,模拟污水系统的硝化活性强于实际污水系统,两者的平均硝化速率分别为7.43 mg NH4+-N/(L.h)和5.55 mg NH4+-N/(L.h)。在前置厌氧段,模拟污水系统的释磷量比实际污水系统高出36.45%。两者在后续好氧阶段都能够充分吸磷。模拟污水系统的平均比好氧速率(SOUR)高达64.54 mg O2/(g MLSS.h),而实际污水系统的则只有32.81 mg O2/(g MLSS.h)。模拟污水系统的污泥絮体疏松,粒径小,形状不规则,沉降性差,沉后出水平均悬浮物浓度(SS)为20 mg/L;而实际污水系统的污泥絮体则密实、粒径大,沉降性好,沉后水十分清澈,SS几乎检测不出。     

Process performance evaluation of the contact stabilisation system at Birzeit University

The purification capacity of the contact stabilisation system at Birzeit University campus has been studied for two years. The oxidation capacity of organic matter, ammonium oxidation, and denitrification potential were determined. The reduction of chemical oxygen demand (COD) was 85%, and the effluent COD concentration was less than 110 mg/l (the average value was 88 mg/l). Suspended solids were removed with equal efficiency. The aerobic stabilization of organic solids was efficient, and no excess biosolids (sludge) had to be removed. High nitrification (70% of the influent nitrogen were nitrified) could be maintained at 15°C, and 42% of the oxidised nitrogen was denitrified. The specific oxygenation capacity of the treatment system is relatively high and reached about 5 kwh/kg COD. The specific wastewater treatment cost is about 0.52 US$/m3 or about 58 US$ per population equivalent per year. Based on the results obtained, batch operation and intermittent aeration of the biological process are suggested to achieve high effluent quality and to reduce power consumption.     

Simultaneous nitrification-denitrification and clarification in a pseudoliquified activated sludge system.

This paper describes results from a pilot study of a novel wastewater treatment technology, which incorporates nutrient removal and solids separation to a single step. The pseudoliquified activated sludge process pilot system was tested on grit removal effluent at flowrates of 29.4 to 54.7 m3/d, three different solid residence times (SRT) (15, 37, and 57 days), and over a temperature range of 12 to 28 degrees C. Despite wide fluctuations in the influent characteristics, the system performed reliably and consistently with respect to organics and total suspended solids (TSS) removals, achieving biochemical oxygen demand (BOD) and TSS reductions of > 96% and approximately 90%, respectively, with BOD5 and TSS concentrations as low as 3 mg/L. Although the system achieved average effluent ammonia concentrations of 2.7 to 3.2 mg/L, nitrification efficiency appeared to be hampered at low temperatures (< 15 degrees C). The system achieved tertiary effluent quality with denitrification efficiencies of 90 and 91% total nitrogen removal efficiency at a total hydraulic retention time of 4.8 hours and an SRT of 12 to 17 days. With ferric chloride addition, effluent phosphorous concentrations of 0.5 to 0.8 mg/L were achieved. Furthermore, because of operation at high biomass concentrations and relatively long biological SRTs, sludge yields were over 50% below typical values for activated sludge plants. The process was modeled using activated sludge model No. 2, as a two-stage system comprised an aerobic activated sludge system followed by an anoxic system. Model predictions for soluble BOD, ammonia, nitrates, and orthophosphates agreed well with experimental data.     

Influence of chemical oxygen demand/total Kjeldahl nitrogen ratio and sludge age on nitrification of nitrogenous wastewater.

Four laboratory-scale biological nitrification units (influent total Kjeldahl nitrogen [TKN] = 1002 to 1062 mg/L) were operated at chemical oxygen demand (COD)/TKN ratios of approximately 0.5, 1.0,15, and 2.0 and at three different sludge ages of 30, 20, and 10 days to study the influence of COD/TKN, sludge age, COD loading, and TKN loading on nitrification and nitrifiers. Percent nitrification was found to increase with decreases in COD/TKN and increases in sludge age. The average nitrifier concentration increased from 460 mg/L at a COD/TKN of 2.22 and a sludge age of 10 days to 706 mg/L at a COD/TKN of 0.676 and a sludge age of 30 days. The nitrifier fraction was found to be higher at a lower COD/TKN and lower at a higher COD/TKN. The nitrifier fraction increased with the decrease in sludge age and COD loadings and the increase in TKN loadings. The effect of sludge age on the nitrifier fraction was amplified at a COD/ TKN of approximately 0.5 rather than at approximately 2.0. The nitrification rate (kilograms TKN oxidized per kilograms nitrifiers per day) was shown to be dependent on COD/TKN and sludge age. The activity performed by Nitrobacter was affected at all COD/TKN ratios studied as well as at a sludge age of 10 days. This was manifested by the accumulation of high levels of nitrite-nitrogen in the nitrified effluent. The presence of heterotrophs did not affect nitrification rates and the growth of nitrifiers, which were found to be beneficial. High sludge age and COD loadings resulted in a higher sludge volume index of more than 200 mL/g mixed liquor suspended solids. Microscopic examination showed filamentous structure of sludge under these conditions. It is concluded from the investigations that a sludge age of 30 days and a COD/TKN of approximately 1.0 are optimal to yield maximum nitrification and nitrifier growth rates for treating high-strength nitrogenous wastewater.