Effect of organic matter on phosphorus recovery from sewage sludge subjected to microwave hybrid pretreatment

Microwave (MW) hybrid processes are able to disrupt the flocculent structure of complex waste activated sludge, and help promote the recovery of phosphorus as struvite. In this study, to optimize struvite yield, (1) the characteristics of matter released in MW-hybrid treatments were compared, including MW, MW-acid, MW-alkali, MW-H₂O₂, and MW-H₂O₂-alkali. The results showed that selective release of carbon, nitrogen, phosphorus, Ca^2 +, and Mg^2 + achieved by sludge pretreatment using MW-hybrid processes. MW-H₂O₂ is the recommended sludge pretreatment process for phosphorus recovery in the form of struvite. The ratio of Mg^2 +:NH₄⁺-N:PO₄^3 −-P was 1.2:2.9:1 in the supernatant. (2) To clarify the effects of organic matter on struvite recovery, the composition and molecular weight distribution of organic matters were analyzed. Low molecular weight COD was found to facilitate the removal rate of NH₄⁺-N and PO₄³-P via crystallization, and the amorphous struvite crystals (< 1 kDa) from the filtered solutions had high purity. Therefore, the present study reveals the necessity of taking into consideration the interference effect of high molecular weight organic matters during struvite crystallization from sewage sludge.     

Investigation on mechanism of phosphate removal on carbonized sludge adsorbent

For the removal of phosphate (PO₄^3 -) from water, an adsorbent was prepared via carbonization of sewage sludge from a wastewater treatment plant: carbonized sludge adsorbent (CSA). The mechanism of phosphate removal was determined after studying the structure and chemical properties of the CSA and its influence on phosphate removal. The results demonstrate that phosphate adsorption by the CSA can be fitted with the pseudo second-order kinetics and Langmuir isotherm models, indicating that the adsorption is single molecular layer adsorption dominated by chemical reaction. The active sites binding phosphate on the surface are composed of mineral particles containing Si/Ca/Al/Fe. The mineral containing Ca, calcite, is the main factor responsible for phosphate removal. The phosphate removal mechanism is a complex process including crystallization via the interaction between Ca^2 + and PO₄^3 -; formation of precipitates of Ca^2 +, Al^3 +, and PO₄^3 -; and adsorption of PO₄^3 - on some recalcitrant oxides composed of Si/Al/Fe.     

Remediation of saline–sodic soil with flue gas desulfurization gypsum in a reclaimed tidal flat of southeast China

Salinization and sodicity are obstacles for vegetation reconstruction of coastal tidal flat soils. A study was conducted with flue gas desulfurization(FGD)-gypsum applied at rates of 0, 15, 30, 45 and 60 Mg/ha to remediate tidal flat soils of the Yangtze River estuary.Exchangeable sodium percentage(ESP), exchangeable sodium(ExNa), p H, soluble salt concentration, and composition of soluble salts were measured in 10 cm increments from the surface to 30 cm depth after 6 and 18 months. The results indicated that the effect of FGD-gypsum is greatest in the 0–10 cm mixing soil layer and 60 Mg/ha was the optimal rate that can reduce the ESP to below 6% and decrease soil p H to neutral(7.0). The improvement effect was reached after 6 months, and remained after 18 months. The composition of soluble salts was transformed from sodic salt ions mainly containing Na~+, HCO_3~-+ CO_3~(2-)and Cl-to neutral salt ions mainly containing Ca~(2+)and SO_4~(2-). Non-halophyte plants were survived at 90%. The study demonstrates that the use of FGD-gypsum for remediating tidal flat soils is promising.     

Characteristics of change in water quality along reclaimed water intake area of the Chaobai River in Beijing, China

To reveal the basic characteristics and controlling factors of water quality change in the project Wenyu to Chaobai reclaimed water diversion, the water quality in the study area was monitored for one year at seven monitoring sites. Inverse geochemical models of the statistical groups were developed using PHREEQC to elucidate the hydrochemistry characteristics of reclaimed water and the factors. The monitoring results indicated that nitrogen and phosphorus contents were significantly reduced along the river mainly caused by seasonal and location variation. The pH ranged from 7.44 to 9.81. Photosynthesis of algae and denitrification in anaerobic microenvironment ultimately led to a sudden p H increase after the Jian River and the Chaobai River confluence. Mg~(2+)and SO_4~(2-) levels dropped obviously in the summer and increased in winter seasons after intersection. Na+and Cl-are relatively stable, and marked drop in the concentration only after the two rivers meet. And there is a decrease of Ca~(2+) and HCO~(3-) and increase in CO_3~(2-) during monitoring period. As a whole, the primary ions and nutrient components, including nitrogen and phosphorus, had high levels in winter. Algae's photosynthesis and respiration were observed to have an impact on the river water quality; there was precipitation–dissolution of minerals and denitrification from upstream to downstream. Inverse geochemical PHREEQC modeling confirmed that there was precipitation of aragonite or calcite, and gypsum or anhydrite in summer, and dissolution in winter; as well as precipitation of dolomite in winter, and cationic exchange and denitrification along the river.     

Comparison between UV and VUV photolysis for the pre- and post-treatment of coking wastewater

In this study, ultraviolet (UV) and vacuum ultraviolet (VUV) photolysis were investigated for the pre-treatment and post-treatment of coking wastewater. First, 6-fold diluted raw coking wastewater was irradiated by UV and VUV. It was found that 15.9%–35.4% total organic carbon (TOC) was removed after 24 hr irradiation. The irradiated effluent could be degraded by the acclimated activated sludge. Even though the VUV photolysis removed more chemical oxygen demand (COD) than UV, the UV-irradiated effluent demonstrated better biodegradability. After 4 hr UV irradiation, the biological oxygen demand BOD₅/COD ratio of irradiated coking wastewater increased from 0.163 to 0.224, and its toxicity decreased to the greatest extent. Second, the biologically treated coking wastewater was irradiated by UV and VUV. Both of them were able to remove 37%–47% TOC within 8 hr irradiation. Compared to UV, VUV photolysis could significantly improve the transparency of the bio-treated effluent. VUV also reduced 7% more ammonia nitrogen (NH₄⁺–N), 17% more nitrite nitrogen (NO₂⁻–N), and 18% more total nitrogen (TN) than UV, producing 35% less nitrite nitrogen (NO₃⁻–N) as a result. In conclusion, UV irradiation was better in improving the biodegradability of coking wastewater, while VUV was more effective at photolyzing the residual organic compounds and inorganic N-species in the bio-treated effluent.     

Use of zeolitized coal fly ash in the simultaneous removal of ammonium and phosphate from aqueous solution

Discharge of wastewater containing nitrogen and phosphate can cause eutrophication. Therefore, the development of an efficient material for the immobilization of the nutrients is important. In this study, a low calcium fly ash and high calcium fly ash were converted into zeolite using the hydrothermal method. The removal of ammonium and phosphate that coexist in aqueous solution by the synthesized zeolites were studied. The results showed that zeolitized fly ash could efficiently eliminate ammonium and phosphate at the same time. Saturation of zeolite with Ca²⁺ rather than Na⁺ favored the removal of both ammonium and phosphate because the cation exchange reaction by the NH₄ ⁺ resulted in the release of Ca²⁺ into the solution and precipitation of Ca²⁺ with PO₄ ³⁻ followed. An increase in the temperature elevated the immobilization of phosphate whereas it abated the removal of ammonium. Nearly 60% removal efficiency for ammonium was achieved in the neutral pH range from 5.5 to 10.5, while the increase or decrease in pH out of the neutral range lowered the adsorption. In contrast, the removal of phosphate approached 100% at a pH lower than 5.0 or higher than 9.0, and less phosphate was immobilized at neutral pH. However, there was still a narrow pH range from 9.0 to 10.5 favoring the removal of both ammonium and phosphate. It was concluded that the removal of ammonium was caused by cation exchange; the contribution of NH₃ volatilization to immobilization at alkaline conditions (up to pH level of 11.4) was limited. With respect to phosphate immobilization, the mechanism was mainly the formation of precipitate as Ca₃(PO₄)₂ within the basic pH range or as FePO₄ and AlPO₄ within acidic pH range.     

Kinetics of nitrobenzene degradation coupled to indigenous microorganism dissimilatory iron reduction stimulated by emulsified vegetable oil

Widespread contamination by nitrobenzene(NB) in sediments and groundwater requires better understanding of the biogeochemical removal process of the pollutant. NB degradation, coupled with dissimilatory iron reduction, is one of the most efficient pollutant removal methods. However, research on NB degradation coupled to indigenous microorganism dissimilatory iron reduction stimulated by electron donors is still experimental. A model for remediation in an actual polluted site does not currently exist.Therefore, in this study, the dynamics was derived from the Michaelis–Menten model(when the mass ratio of emulsified vegetable oil and NB reached the critical value 91:1). The effect of SO_4~(2-), NO_3~-, Ca~(2+)/Mg~(2+), and the grain size of aquifer media on the dynamics were studied, and the NB degradation dynamic model was then modified based on the most significant factors. Utilizing the model, the remediation time could be calculated in a contaminated site.     

The effect of salinity on waste activated sludge alkaline fermentation and kinetic analysis

The effect of salinity on sludge alkaline fermentation at low temperature(20°C) was investigated, and a kinetic analysis was performed. Different doses of sodium chloride(Na Cl, 0–25 g/L) were added into the fermentation system. The batch-mode results showed that the soluble chemical oxygen demand(SCOD) increased with salinity. The hydrolysate(soluble protein, polysaccharide) and the acidification products(short chain fatty acids(SCFAs), NH+4–N, and PO_4~(3-)–P) increased with salinity initially, but slightly declined respectively at higher level salinity(20 g/L or 20–25 g/L). However, the hydrolytic acidification performance increased in the presence of salt compared to that without salt.Furthermore, the results of Haldane inhibition kinetics analysis showed that the salt enhanced the hydrolysis rate of particulate organic matter from sludge particulate and the specific utilization of hydrolysate, and decreased the specific utilization of SCFAs. Pearson correlation coefficient analysis indicated that the importance of polysaccharide on the accumulation of SCFAs was reduced with salt addition, but the importance of protein and NH+4–N on SCFA accumulation was increased.     

Ca and OH release of ceramsites containing anorthite and gehlenite prepared from waste lime mud

Lime mud is a kind of solid waste in the papermaking industry, which has been a source of serious environmental pollution. Ceramsites containing anorthite and gehlenite were prepared from lime mud and fly ash through the solid state reaction method at 1050°C. The objective of this study was to explore the efficiency of Ca^2 + and OH⁻ release and assess the phosphorus and copper ion removal performance of the ceramsites via batch experiments, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that Ca^2 + and OH⁻ were released from the ceramsites due to the dissolution of anorthite, gehlenite and available lime. It is also concluded that gehlenite had stronger capacity for Ca^2 + and OH⁻ release compared with anorthite. The Ca^2 + release could be fit well by the Avrami kinetic model. Increases of porosity, dosage and temperature were associated with increases in the concentrations of Ca^2 + and OH⁻ released. Under different conditions, the ceramsites could maintain aqueous solutions in alkaline conditions (pH = 9.3–10.9) and the release of Ca^2 + was not affected. The removal rates of phosphorus and copper ions were as high as 96.88% and 96.81%, respectively. The final pH values of both phosphorus and copper ions solutions changed slightly. The reuse of lime mud in the form of ceramsites is an effective strategy.     

Influences of anion concentration and valence on dispersion and aggregation of titanium dioxide nanoparticles in aqueous solutions

Dispersion and aggregation of nanoparticles in aqueous solutions are important factors for safe application of nanoparticles. In this study, dispersion and aggregation of nano-TiO₂ in aqueous solutions containing various anions were investigated. The influences of anion concentration and valence on the aggregation size, zeta potential and aggregation kinetics were individually investigated. Results showed that the zeta potential decreased from 19.8 to − 41.4 mV when PO₄^3 − concentration was increased from 0 to 50 mg/L, while the corresponding average size of nano-TiO₂ particles decreased from 613.2 to 540.3 nm. Both SO₄^2 − and NO₃⁻ enhanced aggregation of nano-TiO₂ in solution. As SO₄^2 − concentration was increased from 0 to 500 mg/L, the zeta potential decreased from 19.8 to 1.4 mV, and aggregate sizes increased from 613.2 to 961.3 nm. The trend for NO₃⁻ fluctuation was similar to that for SO₄^2 − although the range of variation for NO₃⁻ was relatively narrow. SO₄^2 − and NO₃⁻ accelerated the aggregation rapidly, while PO₄^3 − did so slowly. These findings facilitate the understanding of aggregation and dispersion mechanisms of nano-TiO₂ in aqueous solutions in the presence of anions of interest.     

Hydroxyl carboxylate based non-phosphorus corrosion inhibition process for reclaimed water pipeline and downstream recirculating cooling water system

A combined process was developed to inhibit the corrosion both in the pipeline of reclaimed water supplies (PRWS) and in downstream recirculating cooling water systems (RCWS) using the reclaimed water as makeup. Hydroxyl carboxylate-based corrosion inhibitors (e.g., gluconate, citrate, tartrate) and zinc sulfate heptahydrate, which provided Zn^2 + as a synergistic corrosion inhibition additive, were added prior to the PRWS when the phosphate (which could be utilized as a corrosion inhibitor) content in the reclaimed water was below 1.7 mg/L, and no additional corrosion inhibitors were required for the downstream RCWS. Satisfactory corrosion inhibition was achieved even if the RCWS was operated under the condition of high numbers of concentration cycles. The corrosion inhibition requirement was also met by the appropriate combination of PO₄^3 − and Zn^2 + when the phosphate content in the reclaimed water was more than 1.7 mg/L. The process integrated not only water reclamation and reuse, and the operation of a highly concentrated RCWS, but also the comprehensive utilization of phosphate in reclaimed water and the application of non-phosphorus corrosion inhibitors. The proposed process reduced the operating cost of the PRWS and the RCWS, and lowered the environmental hazard caused by the excessive discharge of phosphate. Furthermore, larger amounts of water resources could be conserved as a result.     

Layered sphere-shaped TiO2 capped with gold nanoparticles on structural defects and their catalysis of formaldehyde oxidation

We describe here a one-step method for the synthesis of Au/TiO₂ nanosphere materials, which were formed by layered deposition of multiple anatase TiO₂ nanosheets. The Au nanoparticles were stabilized by structural defects in each TiO₂ nanosheet, including crystal steps and edges, thereby fixing the Au–TiO₂ perimeter interface. Reactant transfer occurred along the gaps between these TiO₂ nanosheet layers and in contact with catalytically active sites at the Au–TiO₂ interface. The doped Au induced the formation of oxygen vacancies in the Au–TiO₂ interface. Such vacancies are essential for generating active oxygen species (*O⁻) on the TiO₂ surface and Ti^3 + ions in bulk TiO₂. These ions can then form Ti^3 +–O⁻–Ti^4 + species, which are known to enhance the catalytic activity of formaldehyde (HCHO) oxidation. These studies on structural and oxygen vacancy defects in Au/TiO₂ samples provide a theoretical foundation for the catalytic mechanism of HCHO oxidation on oxide-supported Au materials.     

Phosphate adsorption performance of a novel filter substrate made from drinking water treatment residuals

Phosphate is one of the most predominant pollutants in natural waters. Laboratory experiments were conducted to investigate the phosphate adsorption performance of a(NFS) made from drinking water treatment residuals. The adsorption of phosphate on the NFS fitted well with the Freundlich isotherm and pseudo second-order kinetic models. At p H 7.0, the maximum adsorption capacity of 1.03 mg/g was achieved at 15°C corresponding to the wastewater temperature in cold months, and increased notably to 1.31 mg/g at 35°C.Under both acidic conditions(part of the adsorption sites was consumed) and basic conditions(negative charges formed on the surface of NFS, which led to a static repulsion of PO43-and HPO42-), the adsorption of phosphate was slightly inhibited. Further study showed that part of the adsorption sites could be recovered by 0.25 mol/L Na OH. The activation energy was calculated to be above 8.0 k J/mol, indicating that the adsorption of phosphate on NFS was probably a chemical process. Considering the strong phosphate adsorption capacity and recoverability, NFS showed great promise on enhancing phosphate removal from the secondary treated wastewater in the filtration process.     

Particulate matter assessment of a wetland in Beijing

To increase the knowledge on the particulate matter of a wetland in Beijing, an experimental study on the concentration and composition of PM₁₀ and PM_2.5 was implemented in Beijing Olympic Forest Park from 2013 to 2014. This study analyzed the meteorological factors and deposition fluxes at different heights and in different periods in the wetlands. The results showed that the mean mass concentrations of PM₁₀ and PM_2.5 were the highest at 06:00–09:00 and the lowest at 15:00–18:00. And the annual concentration of PM₁₀ and PM_2.5 in the wetland followed the order of dry period (winter) > normal water period (spring and autumn) > wet period (summer), with the concentration in the dry period significantly higher than that in the normal water and wet periods. The chemical composition of PM_2.5 in the wetlands included NH₄⁺, K⁺, Na⁺, Mg^2 +, SO₄^2 −, NO₃⁻, and Cl⁻, which respectively accounted for 12.7%, 1.0%, 0.8%, 0.7%, 46.6%, 33.2%, and 5.1% of the average annual composition. The concentration of PM₁₀ and PM_2.5 in the wetlands had a significant positive correlation with relative humidity, a negative correlation with wind speed, and an insignificant negative correlation with temperature and radiation. The daily average dry deposition amount of PM₁₀ in the different periods followed the order of dry period > normal water period > wet period, and the daily average dry deposition amount of PM_2.5 in the different periods was dry period > wet period > normal water period.     

MAP沉淀法目标产物最优形成条件及分析方法

为了确定鸟粪石(MAP：MgNH₄PO₄·6H₂O)形成的最优条件,引入化学剖析法,利用酸溶液将鸟粪石沉淀法中所得沉淀物溶解后进行相应的元素分析;提出一种根据沉淀物中的NH⁺₄-N含量间接计算确定鸟粪石含量(即纯度)的分析方法.根据这种计算分析方法,分别得出了不同pH条件下以自来水(主要为地下水)和超纯水作为溶剂所合成的鸟粪石纯度,并对pH和Ca²⁺在鸟粪石形成过程中的影响进行了评估.结果表明,该计算分析方法能够有效实现对MAP沉淀法目标产物的定量分析,弥补了国内外目前普遍依靠XRD技术定性判断所得沉淀物中鸟粪石是否存在的缺陷.以超纯水作为溶剂时,使鸟粪石纯度>90%的最佳pH范围在7.5～9.0,而以自来水为溶剂时,获得相同鸟粪石纯度最佳pH范围则是7.0～7.5.实际污水中常常含有相当数量的Ca²⁺,实施碱性条件(pH>8.0)的MAP沉淀势必大幅降低鸟粪石的纯度.因此,对实际污水回收磷而言,MAP沉淀法的最优pH条件应控制在中性范围(<8.0)以内.     

The nitritation performance of biofilm reactor for treating domestic wastewater under high dissolved oxygen

The objective of this study was to investigate the nitritation performance in a biofilm reactor for treating domestic wastewater.The reactor was operated in continuous feed mode from phases 1 to 3.The dissolved oxygen(DO)was controlled at 3.5–7 mg/L throughout the experiment.The biofilm reactor showed excellent nitritation performance after the inoculation of nitrifying sludge,with the hydraulic retention time being reduced from 24 to 7 hr.Above 90%nitrite accumulation ratio(NAR)was maintained in phase 1.Afterwards,nitratation occurred with the low NH_4~+–N concentration in the reactor.The improvement of NH_4~+–N concentration to 20–35 mg/L had a limited effect on the recovery of nitritation.However,nitritation recovered rapidly when sequencing batch feed mode was adopted in phase 4,with the effluent NH_4~+-N concentration above 7 mg/L.The improvement of ammonia oxidizing bacteria(AOB)activity and the combined inhibition effect of free ammonia(FA)and free nitrous acid(FNA)on the nitrite oxidizing bacteria(NOB)were two key factors for the rapid recovery of nitritation.Sludge activity was obtained in batch tests.The results of batch tests had a good relationship with the long term operation performance of the biofilm reactor.     

Differences in nitrite-oxidizing communities and kinetics in a brackish environment after enrichment at low and high nitrite concentrations

Nitrite accumulation in shrimp ponds can pose serious adverse effects to shrimp production and the environment.This study aims to develop an effective process for the enrichment of ready-to-use nitrite-oxidizing bacteria(NOB)inocula that would be appropriate for nitrite removal in brackish shrimp ponds.To achieve this objective,the effects of nitrite concentrations on NOB communities and nitrite oxidation kinetics in a brackish environment were investigated.Moving-bed biofilm sequencing batch reactors and continuous moving-bed biofilm reactors were used for the enrichment of NOB at various nitrite concentrations,using sediment from brackish shrimp ponds as seed inoculum.The results from NOB population analysis with quantitative polymerase chain reaction(q PCR)show that only Nitrospira were detected in the sediment from the shrimp ponds.After the enrichment,both Nitrospira and Nitrobacter coexisted in the reactors controlling effluent nitrite at 0.1 and 0.5 mg-NO_2~--N/L.On the other hand,in the reactors controlling effluent nitrite at 3,20,and 100 mg-NO_2~--N/L,Nitrobacter outcompeted Nitrospira in many orders of magnitude.The half saturation coefficients(Ks)for nitrite oxidation of the enrichments at low nitrite concentrations(0.1 and 0.5 mg-NO_2~--N/L)were in the range of 0.71–0.98 mg-NO_2~--N/L.In contrast,the Ksvalues of NOB enriched at high nitrite concentrations(3,20,and 100 mg-NO_2~--N/L)were much higher(8.36–12.20 mg-NO_2~--N/L).The results suggest that the selection of nitrite concentrations for the enrichment of NOB inocula can significantly influence NOB populations and kinetics,which could affect the effectiveness of their applications in brackish shrimp ponds.     

Fluoride removal by Al, Ti, and Fe hydroxides and coexisting ion effect

Batch experiments were conducted to evaluate fluoride removal by Al,Fe,and Ti-based coagulants and adsorbents,as well as the effects of coexisting ions and formation of aluminum–fluoride complexes on fluoride removal by co-precipitation with alum(Al_2(SO_4)_3·18H_2O).Aluminum sulfate was more efficient than the other coagulants for fluoride removal in the pH range between 6 and 8.Nano-crystalline TiO_2 was more effective for fluoride removal than Al and Fe hydroxides in a pH range of 3–5.Coexisting anions in water decreased the removal of fluoride in the order:phosphate(2.5 mg/L) arsenate(0.1 mg/L) bicarbonate(200 mg/L) sulfate(100 mg/L) = nitrate(100 mg/L) silicate(10 mg/L) at a pH of 6.0.The effect of silicate became more significant at pH 7.0.Calcium and magnesium improved the removal of fluoride.Zeta-potential measurements determined that the adsorption of fluoride shifted the PZC of Al(OH)_3 precipitates from 8.9 to 8.4,indicating the chemical adsorption of fluoride at the surface.The presence of fluoride in solution significantly increased the soluble aluminum concentration at pH 6.5.A Visual MINTEQ modeling study indicated that the increased aluminum solubility was caused by the formation of AlF~(2+),AlF~(+2),and AlF_3complexes.The AlF_x complexes decreased the removal of fluoride during co-precipitation with aluminum sulfate.     

Application of internal standard method in recombinant luminescent bacteria test

Mercury and its organic compounds have been of severe concern worldwide due to their damage to the ecosystem and human health. The development of effective and affordable technology to monitor and signal the presence of bioavailable mercury is an urgent need. The Mer gene is a mercury-responsive resistant gene, and a mercury-sensing recombinant luminescent bacterium using the Mer gene was constructed in this study. The mer operon from marine Pseudomonas putida strain SP1 was amplified and fused with prompterless luxCDABE in the pUCD615 plasmid within Escherichia coli cells, resulting in pTHE30–E. coli. The recombinant strain showed high sensitivity and specificity. The detection limit of Hg^2 + was 5 nmol/L, and distinct luminescence could be detected in 30 min. Cd^2 +, Cu^2 +, Zn^2 +, Ca^2 +, Pb^2 +, Mg^2 +, Mn^2 +, and Al^3 + did not interfere with the detection over a range of 10^− 5–1 mM. Application of recombinant luminescent bacteria testing in environmental samples has been a controversial issue: especially for metal-sensing recombinant strains, false negatives caused by high cytotoxicity are one of the most important issues when applying recombinant luminescent bacteria in biomonitoring of heavy metals. In this study, by establishing an internal standard approach, the false negative problem was overcome; furthermore, the method can also help to estimate the suspected mercury concentration, which ensures high detection sensitivity of bioavailable Hg^2 +.     

Enhanced dechlorination of 2,4-dichlorophenol by recoverable Ni/Fe–Fe3O4 nanocomposites

Ni/Fe-Fe_3O_4 nanocomposites were synthesized for dechlorination of 2,4-dichlorophenol(2,4-DCP). The effects of the Ni content in Ni/Fe-Fe_3O_4 nanocomposites, solution pH, and common dissolved ions on the dechlorination efficiency were investigated, in addition to the reusability of the nanocomposites. The results showed that increasing content of Ni in Ni/Fe–Fe_3O_4 nanocomposites, from 1 to 5 wt.%, greatly increased the dechlorination efficiency; the Ni/Fe–Fe_3O_4 nanocomposites had much higher dechlorination efficiency than bare Ni/Fe nanoparticles. Ni content of 5 wt.% and initial p H below 6.0 was found to be the optimal conditions for the catalytic dechlorination of 2,4-DCP. Both 2,4-DCP and the intermediate product 2-chlorophenol(2-CP) were completely removed, and the concentration of the final product phenol was close to the theoretical phenol production from complete dechlorination of 20 mg/L of 2,4-DCP, after 3 hr reaction at initial p H value of 6.0,3 g/L Ni/Fe-Fe_3O_4 , 5 wt.% Ni content in the composite, and temperature of 22℃. 2,4-DCP dechlorination was enhanced by Cl-and inhibited by NO3-and SO_4~(2-). The nanocomposites were easily separated from the solution by an applied magnetic field. When the catalyst was reused, the removal efficiency of 2,4-DCP was almost 100% for the first seven uses, and gradually decreased to 75% in cycles 8–10. Therefore, the Ni/Fe–Fe_3O_4 nanocomposites can be considered as a potentially effective tool for remediation of pollution by 2,4-DCP.