Priming effects on PAH degradation and ecotoxicity during a phytoremediation experiment

An experiment was conducted to distinguish priming effects from the effects of phytoremediation of a creosote-polluted soil. The concentration of 13 polycyclic aromatic hydrocarbons (PAHs), and their combined soil toxicity (using four bioassays), was determined on recently excavated, homogenized soil and on such soil subjected to a time-course phytoremediation experiment with lucerne. The results showed a high priming effect, with minor positive and synergistic effects of planting and fertilization on PAH degradation rates. At the end of the experiment, PAH degradation reached 86% of the initial 519 mg PAHs kg(-1). Two of the four toxicity tests (bioluminescence inhibition and ostracod growth inhibition) corroborated the chemical data for residual PAHs, and indicated a significant reduction in soil toxicity. We conclude that priming effects can easily surpass treatment effects, and that an unintentional pre-incubation that ignores these effects can jeopardize the full quantitative assessment of in situ bioremediation of contaminated soil.     

Remediation of polycyclic aromatic hydrocarbon and metal-contaminated soil by successive methyl-β-cyclodextrin-enhanced soil washing–microbial augmentation: a laboratory evaluation

Polycyclic aromatic hydrocarbon (PAH) and metal-polluted sites caused by abandoned coking plants are receiving wide attention. To address the associated environmental concerns, innovative remediation technologies are urgently needed. This study was initiated to investigate the feasibility of a cleanup strategy that employed an initial phase, using methyl-β-cyclodextrin (MCD) solution to enhance ex situ soil washing for extracting PAHs and metals simultaneously, followed by the addition of PAH-degrading bacteria (Paracoccus sp. strain HPD-2) and supplemental nutrients to treat the residual soil-bound PAHs. Elevated temperature (50 °C) in combination with ultrasonication (35 kHz, 30 min) at 100 g MCD L^?1 was effective in extracting PAHs and metals to assist soil washing; 93 % of total PAHs, 72 % of Cd, 78 % of Ni, 93 % of Zn, 84 % of Cr, and 68 % of Pb were removed from soil after three successive washing cycles. Treating the residual soil-bound PAHs for 20 weeks led to maximum biodegradation rates of 34, 45, 36, and 32 % of the remaining total PAHs, 3-ring PAHs, 4-ring PAHs, and 5(+6)-ring PAHs after washing procedure, respectively. Based on BIOLOG Ecoplate assay, the combined treatment at least partially restored microbiological functions in the contaminated soil. The ex situ cleanup strategy through MCD-enhanced soil washing followed by microbial augmentation can be effective in remediating PAH and metal-contaminated soil.     

PAH removal from spiked municipal wastewater sewage sludge using biological, chemical and electrochemical treatments

Polycyclic aromatic hydrocarbons (PAHs) have been widely studied due to their presence in all the environmental media and toxicity to life. These molecules are strongly adsorbed on the particulate matters of soils, sludges or sediments because of their strong hydrophobicity which makes them less bioavailability, thus limiting their bioremediation. Different sludge treatment processes were tested to evaluate their performances for PAH removal from sludge prealably doped with 11 PAHs (5.5mg each PAH kg(-1) of dry matter (DM)): two biological processes (mesophilic aerobic digestion (MAD) and simultaneous sewage sludge digestion and metal leaching (METIX-BS)) were tested to evaluate PAH biodegradation in sewage sludge. In parallel, two chemical processes (quite similar Fenton processes: chemical metal leaching (METIX-AC) and chemical stabilization (STABIOX)) and one electrochemical process (electrochemical stabilization (ELECSTAB)) were tested to measure PAH removal by these oxidative processes. Moreover, PAH solubilisation from sludge by addition of a nonionic surfactant Tween 80 (Tw80) was also tested. The best yields of PAH removal were obtained by MAD and METIX-BS with more than 95% 3-ring PAH removal after a 21-day treatment period. Tw80 addition during MAD treatment increased 4-ring PAHs removal rate. In addition, more than 45% of 3-ring PAHs were removed from sludge by METIX-AC and during ELECSTAB process were quiet good with approximately 62% of 3-ring PAHs removal. However, little weaker removal of 3-ring PAHs (<35%) by STABIOX. None of the tested processes were efficient for the elimination of high molecular weight (> or = 5-ring) PAHs from sludge.     

Comparison of solid and liquid-phase bioassays using ecoscores to assess contaminated soils

Bioassays on aqueous and solid phases of contaminated soils were compared, belonging to a wide array of trophic and response levels and using ecoscores for evaluating ecotoxicological and genotoxicological endpoints. The method was applied to four coke factory soils contaminated mainly with PAHs, but also to a lesser extent by heavy metals and cyanides. Aquatic bioassays do not differ from terrestrial bioassays when scaling soils according to toxicity but they are complementary from the viewpoint of ecological relevance. Both aquatic and terrestrial endpoints are strongly correlated with concentrations of 3-ring PAHs. This evaluation procedure allows us to propose a cost-effective battery which embraces a wide array of test organisms and response levels: it includes two rapid bioassays (Microtox(?) and springtail avoidance), a micronucleus test and three bioassays of a longer duration (algal growth, lettuce germination and springtail reproduction). This battery can be recommended for a cost-effective assessment of polluted/remediated soils.     

Solid-phase bioassays and soil microbial activities to evaluate PAH-spiked soil ecotoxicity after a long-term bioremediation process simulating landfarming

The residual ecotoxicity of long-term bioremediated soils concomitantly spiked with three PAHs at four levels (15, 75, 150, 300 mg Sigma 3 PAHs kg(-1) soil) was evaluated using physico-chemical analyses, solid-phase bioassays and soil microbial activities. The pot-scale bioremediation process consisted of weekly moderate waterings in the presence or absence of sewage sludge compost (SSC) under greenhouse conditions. After 15 months, anthracene and pyrene were almost completely degraded whereas benzo[a]pyrene was still persisting, most apparently in SSC-amended soil treatments. However, no apparent toxic effects of the residual PAHs could be detected. SSC application at 40 t ha(-1) was performed to valorize the biowaste and stimulate PAH biodegradation but caused soil salinization and pH reduction at the end of the bioremediation process. Consequently, SSC-amended soils were characterized by strong phytotoxicity to lettuce and had adverse effects on the ostracod Heterocypris incongruens. Despite the smaller number of culturable bacterial populations in SSC-amended soils, soil enzymatic activities were not affected by the organic amendment and residual PAHs; and the bioremediation efficiency was likely to be more limited by the bioavailability of PAHs rather than by the total number of PAH-degraders.     

Chemical and bioanalytical characterisation of PAHs in risk assessment of remediated PAH-contaminated soils

Polycyclic aromatic hydrocarbons (PAHs) are common contaminants in soil at former industrial areas; and in Sweden, some of the most contaminated sites are being remediated. Generic guideline values for soil use after so-called successful remediation actions of PAH-contaminated soil are based on the 16 EPA priority pollutants, which only constitute a small part of the complex cocktail of toxicants in many contaminated soils. The aim of the study was to elucidate if the actual toxicological risks of soil samples from successful remediation projects could be reflected by chemical determination of these PAHs. We compared chemical analysis (GC-MS) and bioassay analysis (H4IIE-luc) of a number of remediated PAH-contaminated soils. The H4IIE-luc bioassay is an aryl hydrocarbon (Ah) receptor-based assay that detects compounds that activate the Ah receptor, one important mechanism for PAH toxicity. Comparison of the results showed that the bioassay-determined toxicity in the remediated soil samples could only be explained to a minor extent by the concentrations of the 16 priority PAHs. The current risk assessment method for PAH-contaminated soil in use in Sweden along with other countries, based on chemical analysis of selected PAHs, is missing toxicologically relevant PAHs and other similar substances. It is therefore reasonable to include bioassays in risk assessment and in the classification of remediated PAH-contaminated soils. This could minimise environmental and human health risks and enable greater safety in subsequent reuse of remediated soils.     

Removal of polycyclic aromatic hydrocarbons from manufactured gas plant-contaminated soils using sunflower oil: laboratory column experiments

Laboratory column experiments were performed to remove PAHs (polycyclic aromatic hydrocarbons) from two contaminated soils using sunflower oil. Two liters of sunflower oil was added to the top of the columns (33 cm x 21 cm) packed with 1 kg of PAH-contaminated soil. The sunflower oil was applied sequentially in two different ways, i.e. five additions of 400 ml or two additions of 1l. The influence of PAH concentration and the volume of sunflower oil on PAH removal were examined. A soil respiration experiment was carried out and organic carbon contents of the soils were measured to determine degradability of remaining sunflower oil in the soils. Results showed that the sunflower oil was effective in removing PAHs from the two soils, more PAHs were removed by adding sunflower oil in two steps than in five steps, probably because of the slower flow rate in the former method. More than 90% of total PAHs was removed from a heavily contaminated soil (with a total 13 PAH concentration of 4721 mg kg(-1)) using 4 l of sunflower oil. A similar removal efficiency was obtained for another contaminated soil (with a total 13 PAH concentration of 724 mg kg(-1)), while only 2l was needed to give a similar efficiency. Approximately 4-5% of the sunflower oil remained in the soils. Soil respiration curves showed that remaining sunflower oil was degraded by allowing air exchange and supplying with nutrients. Organic carbon content of the soil was restored to original level after 180 d incubation. These results indicated that the sunflower oil had a great capacity to remove PAHs from contaminated soils, and sunflower oil solubilization can be an alternative technique for remediation of PAH contaminated soils.     

A multi-process phytoremediation system for removal of polycyclic aromatic hydrocarbons from contaminated soils

To improve phytoremediation processes, multiple techniques that comprise different aspects of contaminant removal from soils have been combined. Using creosote as a test contaminant, a multi-process phytoremediation system composed of physical (volatilization), photochemical (photooxidation) and microbial remediation, and phytoremediation (plant-assisted remediation) processes was developed. The techniques applied to realize these processes were land-farming (aeration and light exposure), introduction of contaminant degrading bacteria, plant growth promoting rhizobacteria (PGPR), and plant growth of contaminant-tolerant tall fescue (Festuca arundinacea). Over a 4-month period, the average efficiency of removal of 16 priority PAHs by the multi-process remediation system was twice that of land-farming, 50% more than bioremediation alone, and 45% more than phytoremediation by itself. Importantly, the multi-process system was capable of removing most of the highly hydrophobic, soil-bound PAHs from soil. The key elements for successful phytoremediation were the use of plant species that have the ability to proliferate in the presence of high levels of contaminants and strains of PGPR that increase plant tolerance to contaminants and accelerate plant growth in heavily contaminated soils. The synergistic use of these approaches resulted in rapid and massive biomass accumulation of plant tissue in contaminated soil, putatively providing more active metabolic processes, leading to more rapid and more complete removal of PAHs.     

Behavior of PAHs during cold storage of historically contaminated soil samples

The stability of historically polycyclic aromatic hydrocarbon (PAH)-contaminated soils during cold storage was investigated. Samples from two former manufactured gas plants exhibited quantitative recoveries of PAHs over the whole period of sample holding at 4 °C in the dark (8–10 months), whereas significant losses of PAHs were observed for soils received from a former railroad sleeper preservation plant with low molecular weight compounds being notably more affected compared to heavier PAHs. Already after 2 weeks of holding time, 3-ring PAHs in one of theses samples were down to 29–73% of the initial concentration and significant losses were observed for up to 5-ring compounds. Dissipation of PAHs was found to be predominantly due to aerobic microbial metabolism since sodium azide poisoned samples showed quantitative recoveries for all PAHs over the entire storage time of 3 months. A similar stabilizing effect was observed for freezing at −20 °C as means of preservation. Except for acenaphthene, no significant loss for any of the PAHs was observed over 6 weeks of holding time. Eventually, selected chemical, physical, and biological parameters of two soils were investigated and identified as potential indicators for the stability of PAH-contaminated soil samples.     

Assessment of contaminant lability during phytoremediation of polycyclic aromatic hydrocarbon impacted soil

Polycyclic aromatic hydrocarbons (PAHs) are recalcitrant compounds, some of which are known carcinogens, often found in high residual soil concentrations at industrial sites. Recent research has confirmed that phytoremediation holds promise as a low-cost treatment method for PAH contaminated soil. In this study, the lability of soil bound PAHs in the rhizosphere was estimated using solid phase extraction resin. An extraction time of 14 days was determined to be appropriate for this study. Resin-extractable PAHs, which are assumed to be more bioavailable, decreased during plant treatments. Significant reductions in the labile concentrations of several PAH compounds occurred over 12 months of plant growth. The differences in concentration between the unplanted and the planted soil indicate that the presence of plant roots, in addition to the passage of time, contributes to reduction in the bioavailability of target PAHs.     

Dissolution and removal of PAHs from a contaminated soil using sunflower oil

This study reports on the feasibility of remediation of polycyclic aromatic hydrocarbon (PAH) contaminated soils using sunflower oil, an environmentally-friendly solvent. Batch experiments were performed to test the influence of oil/soil ratio on the remediation of PAH contaminated soil, and to test the mass transfer behaviors of PAHs from soil to oil. An empirical model was employed to describe the kinetics of PAH dissolution and to predict equilibrium concentrations of PAHs in oil. PAH containing oil was regenerated using active carbon. Results show that dissolution of PAHs from a Manufactured Gas Plant (MGP) soil at oil/soil ratios of one or two were almost the same. Nearly all PAHs (81-100%) could be removed by sunflower oil dissolution. Mass transfer coefficients for low molecular PAHs namely fluoranthene, phenanthrene and anthracene were one or two orders of magnitude higher than those for high molecular PAHs with 4-6 rings. Ninety milliliters of PAH containing oil could be regenerated by 10 g active carbon in a batch reactor. Such a remediation procedure indicates that sunflower oil is a promising agent for the removal of PAHs from MGP soils. However, further research is required before the method can be used for in situ remediation of contaminated sites.     

PAH dissipation in a contaminated river sediment under oxic and anoxic conditions

A batch experiment was conducted to compare PAH degradation in a polluted river sediment under aerobic and anaerobic conditions, and to investigate whether input of fresh organic material (cellulose) could enhance such degradation. All measurements were checked against abiotic control treatments to exclude artifacts of sample preparation and non-biological processes like aging. Three- and four-ring PAHs could be degraded by the indigenous microbial community under aerobic conditions, but anaerobic metabolism based on iron and sulphate reduction was not coupled with PAH degradation of even the simplest 3-ring compounds like phenanthrene. Cellulose addition stimulated both aerobic and anaerobic respiration, but had no effect on PAH dissipation. We conclude that natural attenuation of PAHs in polluted river sediments under anaerobic conditions is exceedingly slow. Dredging and biodegradation on land under aerobic conditions would be required to safely remediate and restore polluted sites.     

Dissipation of polycyclic aromatic hydrocarbons (PAHs) in the rhizosphere: Synthesis through meta-analysis

Polycyclic aromatic hydrocarbons (PAHs) are widespread and persistent organic pollutants with high carcinogenic effect and toxicity; their behavior and fate in the soil-plant system have been widely investigated. In the present paper, meta-analysis was used to explore the interaction between plant growth and dissipation of PAHs in soil based on the large body of published literature. Plants have a promoting effect on PAH dissipation in soils. There was no difference in PAH dissipation between soils contaminated with single and mixed PAHs. However, plants had a more obvious effect on PAH dissipation in freshly-spiked soils than in long-term field-polluted soils. Additionally, a positive effect of the number of microbial populations capable of degrading PAHs was observed in the rhizosphere compared with the bulk soil. Our meta-analysis established the importance of the rhizosphere effect on PAH dissipation in variety of the soil-plant systems.     

PAHs associated with the leaves of three deciduous tree species. I--Concentrations and profiles

Results for the concentrations of total polycyclic aromatic hydrocarbons (Sigma PAH) and the PAH profile in leaves from three deciduous tree species from the same woodland are presented, and discussed with reference to environmental and leaf-related variables. There were significant differences between oak, ash and hazel leaves in their Sigma PAH concentrations (sum of 23 PAHs), and in the relative contribution of individual PAHs to the sum. Leaves exhibiting pubescence (hairiness) were found to have significantly higher Sigma PAH concentrations than hairless leaves, regardless of their position in the vegetation strata of the wood. Hazel leaves from the understorey had a PAH profile consisting of a greater proportion of the 4-, 5- and 6-ring PAHs than oak or ash from the canopy. This was concluded to be the result of the filtering effect of the main canopy on the air passing over and through it, with subsequent transfer of particles and attendant PAHs to the understorey below. The proportion of Sigma PAH contributed by the 6-ring PAH in hazel leaves was negatively correlated with distance from the southern edge of the canopy. It is proposed that the predominantly windward edges of the woodland, where atmospheric turbulence is likely to be greatest, favoured the deposition of particle-bound PAHs to leaves.     

Comparison of solid-phase bioassays and ecoscores to evaluate the toxicity of contaminated soils

Five bioassays (inhibition of lettuce germination and growth, earthworm mortality, inhibition of springtail population growth, avoidance by springtails) were compared, using four coke factory soils contaminated by PAHs and trace elements, before and after biotreatment. For each bioassay, several endpoints were combined in an ‘ecoscore’, a measure of test sensitivity. Ecoscores pooled over all tested bioassays revealed that most organisms were highly sensitive to the concentration of 3-ring PAHs. When four soils were combined, behavioural tests using the springtail Folsomia candida showed higher ecoscores, i.e. they were most sensitive to soil contamination. However, despite overall higher sensitivity of behavioural tests, which could be used for cheap and rapid assessment of soil toxicity, especially at low levels of contamination, some test endpoints were more sensitive than others, and this may differ from a soil to another, pointing to the need for a battery of bioassays when more itemized results are expected.     

PAHs associated with the leaves of three deciduous tree species. II: uptake during a growing season.

Leaves from three species of deciduous tree (oak, ash and hazel) were sampled at intervals through a growing season in a mature, mixed-deciduous woodland. Polycyclic aromatic hydrocarbon (PAH) concentrations remained within a small range for all species between May and September, deviating significantly only when increases in atmospheric concentrations of PAHs (notably from the 'Bonfire night' festival in early autumn) have been shown. We concluded that the influence of air concentrations was more important than meteorological conditions (temperature, humidity and rainfall) in determining plant concentrations of PAHs over a growing season. Concentrations of 4-, 5- and 6-ring PAHs were positively correlated with time for all species, but there were significant differences in the PAH profile between species sampled from the canopy (oak and ash) compared with the understorey (hazel). Oak and ash had similar PAH profiles, while hazel leaves had proportionally greater concentrations of the heavier molecular weight (4-, 5- and 6-ring) PAHs, and the ratios of these compounds to 3-ring PAHs was positively correlated with time. This affirms earlier work conducted on the same species in the same woodland, where we concluded that the canopy was filtering particles and attendant PAHs from air passing over or through it, and that these particles were transferred to the understorey and the woodland floor.     

Influence of mature compost amendment on total and bioavailable polycyclic aromatic hydrocarbons in contaminated soils

A laboratory microcosm study was carried out to assess the influence of compost amendment on the degradation and bioavailability of PAHs in contaminated soils. Three soils, contaminated with diesel, coal ash and coal tar, respectively, were amended with two composts made from contrasting feedstock (green waste and predominantly meat waste) at two different rates (250 and 750 t ha^?1) and incubated for 8 months. During this period the treatments were sampled for PAH analysis after 0, 3, 6 and 8 months. Total and bioavailable fractions were obtained by sequential ultrasonic solvent extraction and hydroxypropyl-β-cyclodextrin extraction, respectively, and PAHs were identified and quantified by GC–MS. Bioavailability decrease due to sorption was only observed at the first 3 months in the diesel spiked soil. After 8 months, compost addition resulted in over 90% loss of total PAHs irrespective of soil types. Desorption and degradation contributed to 30% and 70%, respectively, of the PAH loss in the spiked soil, while PAH loss in the other two soils resulted from 40% enhanced desorption and 60% enhanced degradation. Compost type and application rates had little influence on PAH bioavailability, but higher PAH removal was observed at higher initial concentration during the early stage of incubation. The bioavailable fraction of PAH was inversely correlated to the number of benzene rings and the octanol–water partition coefficient. Further degradation was not likely after 8-month although over 30% of the residual PAHs were bioavailable, which highlighted the application of bioavailability concept during remediation activities.     

Sources and patterns of polycyclic aromatic hydrocarbons pollution in kitchen air,China

Twelve polycyclic aromatic hydrocarbons, multi-ringed compounds known to be carcinogenic in air of six domestic kitchens and four commercial kitchens of China were measured in 1999-2000. The mean concentration of total PAHs in commercial kitchens was 17 microg/m3, consisting mainly of 3- and 4-ring PAHs, and 7.6 microg/m3 in domestic kitchens, where 2- and 3-ring PAHs were predominant, especially naphthalene. The BaP levels in domestic kitchens were 0.0061-0.024 microg/m3 and 0.15- 0.44 microg/m3 in commercial kitchens. Conventional Chinese cooking methods were responsible for such heavy PAHs pollution. The comparative study for PAH levels in air during three different cooking practices: boiling, broiling and frying were conducted. It was found that boiling produced the least levels of PAHs. For fish, a low-fat food, frying it produced a larger amount of PAHs compared to broiling practice, except pyrene and anthracene. In commercial kitchens, PAHs came from two sources, cooking practice and oil-fumes, however the cooking practice had a more predominant contribution to PAHs in commercial kitchen air. In domestic kitchens, except for cooking practice and oil-fumes, there were other PAHs sources, such as smoking and other human activities in the domestic houses, where 3-4 ring PAHs mainly came from cooking practice. Naphthalene (NA, 2-ring PAHs) was the most predominant kind, mostly resulting from the evaporation of mothball containing a large quantity of NA, used to prevent clothes against moth. A fingerprint of oil-fumes was the abundance of 3-ring PAHs. Heating at the same temperature, the PAHs concentrations in different oil-fumes were lard > soybean oil > rape-seed oil. An increase in cooking temperature increased the levels of PAHs, especially acenaphthene.     

Release of polycyclic aromatic hydrocarbons from Yangtze River sediment cores during periods of simulated resuspension

The role of resuspension duration on release of 16 PAHs was measured experimentally using a particle entrainment simulator (PES). Three sediment cores were resuspended for 12h at 0.2 and 0.5N m(-2). PAHs in water column and total suspended solids (TSS) were monitored at intervals. After 0.25h of resuspension, PAH release was on average 42% of their concentrations after 12h of resuspension, indicating fast release of PAHs from sediments in an initial short time. Moreover, PAHs released faster at 0.5N m(-2) than at 0.2N m(-2); low molecular weight PAHs (2-3-ring) released faster than median molecular weight (4-ring) PAHs. PAH concentrations in TSS showed generally increase with time and differences in magnitudes based on sediment type and energy. Overall, the composition of sediments is the major factor in determining the amount of released PAHs, more so than the level of resuspension energy applied.     

Particle-bound PAH content in ambient air

Ambient air samples from a traffic intersection, an urban site and a petrochemical-industrial site (PCI) were collected by using several dry deposition plates, two Microorifice uniform deposited impactors (MOUDIs), one Noll Rotary Impactor (NRI) and several PS-1 (General Metal Work) samplers from March 1994 to June 1995 in southern Taiwan, to characterize the atmospheric particle-bound PAH content of these three areas. Twenty-one individual polycyclic aromatic hydrocarbons (PAHs) were analyzed primarily by using a gas chromatograph/mass spectrometer (GC/MS). In general, the sub-micron particles have a higher PAH content. This is due to the fact that soot from combustion sources consists primarily of fine particles and has a high PAH content. In addition, a smaller particle has a higher specific surface area and therefore may contain more organic carbon, which allows for more PAH adsorption. For a particle size range between 0.31 and 3.2 microm, both Urban/Traffic and PCI/Traffic ratios of particle-bound total-PAH content have the lowest values, ranging from 0.25 to 0.28 (mean = 0.26) and from 0.07 to 0.13 (mean = 0.10), respectively. This indicates that, during the accumulation process, the PAH mass shifted from a particle phase to a gas phase, or the particles aggregated with lower PAH-content particles, resulting in a reduction in particle-bound PAH content. By using the particle size distribution data, the dry deposition model in this study can provide a good prediction for the PAH content of dry deposition materials. In general, lower molecular weight PAHs had a larger fraction of dry deposition flux contributed by the gas phase; for 2-ring PAH (50.4, 46.3 and 28.4%), 3-ring PAHs (15.2, 15.4 and 11.7%) and 4-ring PAHs (13.0, 3.60 and 5.01%) for the traffic intersection, urban and PCI sites, respectively. For higher molecular weight PAHs-5-ring, 6-ring and 7-ring PAHs-their cumulation fraction (F%) of dry deposition flux contributed by the gas phase was lower than 3.26%. At the traffic intersection, urban and PCI sites, the mass median diameter of dry deposition materials (MMD(F)) of individual PAHs was between 25.3 and 49.6 microm, between 27.6 and 43.9 microm, and between 19.1 and 41.9 microm, respectively. This is due to the fact that PAH dry-deposition primarily resulted from gravitational settling of the coarse particulates (> 10 microm).