Sorption and cosorption of organic contaminant on surfactant-modified soils

Three kinds of soils were modified with the cationic surfactants, hexadecyltrimethylammonium (HDTMA) bromide and tetramethylammonium (TMA) bromide to increase their sorptive capabilities. Sorption of chlorobenzene in simulated groundwater by these soils was investigated. HDTMA-modified soil has a higher ability to sorb chlorobenzene from simulated groundwater than unmodified soil. TMA-modified soil did not show the superiority. HDTMA thus can be used to modify soil to improve its sorption capability. Cosorption of chlorobenzene in simulated groundwater in the absence or presence of nitrobenzene and dichloromethane on HDTMA-modified soil was also investigated. Nitrobenzene facilitated sorption of chlorobenzene on all HDTMA-modified soil. Dichloromethane did not influence the sorption of chlorobenzene by HDTMA-modified soil. The results suggest that HDTMA-modified soil is a highly effective sorbent for chlorobenzene and multiple organic compounds did not impede the uptake of chlorobenzene.     

Sorption and desorption kinetics of diuron, fluometuron, prometryn and pyrithiobac sodium in soils

The sorption and desorption characteristics of four herbicides (diuron, fluometuron, prometryn and pyrithiobac-sodium) in three different cotton growing soils of Australia was investigated. Kinetics and equilibrium sorption and desorption isotherms were determined using the batch equilibrium technique. Sorption was rapid (> 80% in 2 h) and sorption equilibrium was achieved within a short period of time (ca 4 h) for all herbicides. Sorption isotherms of the four herbicides were described by Freundlich equation with an r2 value > 0.98. The herbicide sorption as measured by the distribution coefficient (Kd) values ranged from 3.24 to 5.71 L/kg for diuron, 0.44 to 1.13 L/kg for fluometuron, 1.78 to 6.04 L/kg for prometryn and 0.22 to 0.59 L/kg for pyrithiobac-sodium. Sorption of herbicides was higher in the Moree soil than in Narrabri and Wee Waa soils. When the Kd values were normalised to organic carbon content of the soils (Koc), it suggested that the affinity of the herbicides to the organic carbon increased in the order: pyrithiobac-sodium < fluometuron < prometryn < or = diuron. The desorption isotherms were also adequately described by the Freundlich equation. For desorption, all herbicides exhibited hysteresis and the hysteresis was stronger for highly sorbed herbicides (diuron and prometryn) than the weakly sorbed herbicides (fluometuron and pyrithiobac-sodium). Hysteresis was also quantified as the percentage of sorbed herbicides which is not released during the desorption step (omega = [nad/nde - 1] x 100). Soil type and initial concentration had significant effect on omega. The effect of sorption and desorption properties of these four herbicides on the off-site transport to contaminate surface and groundwater are also discussed in this paper.     

Complexation of the antibiotic tetracycline with humic acid

The effect of solution chemistry and sorbate-to-sorbent ratio on the interaction of the antibiotic tetracycline with Elliott soil humic acid (ESHA) was investigated using equilibrium dialysis and FITEQL modeling. Tetracycline speciation strongly influenced its sorption to ESHA. Sorption was strongly pH-dependent with a maximum around pH 4.3, and competition with H+ and electrolyte cation (Na+) was evident. The pH-dependent trend was consistent with complexation between the cationic/zwitterionic tetracycline species and deprotonated sites in ESHA (mainly carboxylic functional groups). Modification of ESHA by Ca2+ addition increased tetracycline sorption suggesting that ternary complex formation (ESHA-metal-tetracycline) may be important at higher concentrations of multivalent metal cations. The macroscopic data (pH-envelope and sorption isotherms) were successfully modeled using a discrete logK function with the FITEQL 4.0 chemical equilibrium program indicating that ESHA-tetracycline interaction could be reasonably represented as complex formation of a monoacid with discrete sites in humic acid. Sorption-desorption hysteresis was observed; both sorption and desorption isotherms were well described by the Freundlich equation.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48–72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K _d) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Sorption-desorption of atrazine and diuron in soils from southern Brazil

The objective of this study was to investigate the behavior of sorption and desorption of the herbicides atrazine (6-chloro-N2-ethyl-N4-isopropyl-1,3,5-triazine-2,4-diamine) and diuron [3-(3,4-dichlorophenyl)-1,1-dimethyleurea] in soil samples from a typical lithosequence located in the municipality of Mamborê (PR), southern Brazil. Five concentrations of 14C-atrazine and 14C-diuron were used for both herbicides (0.48, 0.96, 1.92, 3.84, and 7.69 mg L(-1)). Sorption of both herbicides correlated positively with the organic carbon and clay content of the soil samples. Sorption isotherms were well described by the Freundlich model. The slope values of the isotherm (N) ranged from 0.84 to 0.90 (atrazine) and from 0.75 to 0.79 (diuron) for the lithosequence samples. Sorption of diuron was high regardless of the soil texture or the concentration added. The desorption isotherms for atrazine and diuron showed good fit to the Freundlich equation (R2 >or= 0,87). Atrazine slope values for the desorption isotherms were similar for the different concentrations and were much lower than those observed for the sorption isotherms. Significant hysteresis was observed in the herbicide desorption. When the two herbicides were compared, it was found that diuron (N = 0.06-0.22) presented more pronounced hysteresis than atrazine. The results showed that, quantitatively, a greater atrazine fraction applied to these soils remains available to be leached in the soil profile, as compared to diuron.     

Sorption behavior of metolachlor, isoproturon, and terbuthylazine in soils

The sorption-desorption of metolachlor [2-chloro-N-(ethyl-6-methyl phenyl)-N-(2-methoxy-1-methyl ethyl) acetamide], isoproturon [3-(4-isopropyl phenyl)-1,1-dimethyl urea] and terbuthylazine [N6-tert butyl-6-chloro-N4-ethyl-1,3,5-triazine-2,4-diamine] herbicides was studied in two German soils at 1:10 soil to water ratio by batch method. Equilibrium of herbicides between soil and water (0.01 M CaCl2) was attained in 2 h. Sorption data fitted very well to Freundlich equation, represented by very high correlation coefficient (r2 > 0.934). Comparison of Freundlich K values indicated that sorption of all the three herbicides was most pronounced in soil having higher organic carbon content. Koc values were as expected nearly identical for each herbicide in the two soils. The Freundlich constant (1/n) was about 1 for metolachlor and less than 1 for terbuthylazine and isoproturon indicating a L-type of sorption isotherms. Desorption of all the three herbicides showed hysteresis. Nearly equal amounts of metolachlor, isoproturon and terbuthylazine were desorbed from both soils. There was a good correlation between Koc and solubility.     

Efficiency of recycled wool-based nonwoven material for the removal of oils from water

The aim of this study was to highlight the potential use of recycled wool-based nonwoven material for the removal of diesel fuel, crude, base, vegetable and motor oil from water. Sorption capacity of the material in water and in oil without water, oil retention, sorbent reusability and buoyancy in static and dynamic conditions were investigated. The results show high sorption capacity of recycled wool for different kinds of oil. This sorbent also exhibited excellent buoyancy after 24h of sorption as well as a good reusability since the decrease in sorption capacity did not exceed 50% of the initial value after five sorption cycles in oil without water.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48-72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K(d)) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Simultaneous sorption of lead and chlorobenzene by organobentonite

Clays or organoclays have been used as a barrier to prevent the transport of hazardous contaminants in landfills. However, clays are known to effectively sorb mostly inorganic contaminants, while organoclays are mainly used for organic contaminants. Since the organoclays are basically clay particles modified with cationic surfactants, there might exist an optimal coverage of cationic surfactant on the clay particles to sorb both inorganic and organic contaminants. In order to determine the optimal mass of cationic surfactants on the bentonites, sodium bentonites were treated with various ratios of hexadecyltrimethylammonium (HDTMA) to bentonites. Chlorobenzene and lead were selected as representative contaminants. When either chlorobenzene or lead exists as a single contaminant, chlorobenzene sorption increased with increasing HDTMA to bentonite ratios, and lead sorption decreased with increasing HDTMA to bentonite ratios. Sorption of chlorobenzene was a function of HDTMA coverage on the bentonites, while lead sorption was much more influenced by the initial lead concentration rather than the mass of HDTMA added to the bentonites.     

Sorption behavior of a new acidic herbicide in soils

The sorptive behavior of the experimental herbicide quinmerac (7-chloro-3-methyl-quinoline-8-carboxylic acid) was investigated in soils of different organic carbon content. Distribution coefficients are low (K_d = 0.03 - 12 mL g⁻¹) and are mainly determined by the soil organic carbon content. The adsorption mechanism operating in neutral to slightly acid agricultural soils is supposed to be cation bridging with the anionic form of quinmerac. Under acid conditions (pH 5.2) the predominating sorption mechanism is hydrophobic interaction. Therefore soil pH and cationic composition are also major factors determining the sorptive capacity of soils for quinmerac.

Adsorption kinetics, equilibrium adsorption and desorption isotherms were determined in batch experiments. Sorption kinetics were investigated at various times from 15 min to 96 hours. A two-step sorption behavior with time was found for the anionic form indicating two types of sorption mechanisms or sorption sites. Equilibrium for the first type was reached at a time-scale of minutes and for the second type after 24 hours. Adsorption isotherms were determined for two soil/solution ratios 1/5 and 1/3. Alteration of the adsorbent concentration exerted a strong influence on the adsorption isotherms. An increase of sorption was found with increasing adsorbent concentration. Under natural soil conditions sorption is therefore expected to be higher compared to the batch experiments. Desorption isotherms were obtained using the consecutive desorption method. Desorption hysteresis was not observed which indicates weak interactions. Implications of the results for the movement of quinmerac under field conditions and for models describing transport are discussed.     

Effects of SOM, surfactant and pH on the sorption-desorption and mobility of prometryne in soils

Sorption and desorption of the herbicide prometryne in two types of soil subjected to the changes of pH and soil organic matter and surfactant were investigated. The sorption and desorption isotherms were expressed by the Freundlich equation. Freundlich K_f and n values indicate that soil organic matter was the major factor affecting prometryne behavior in the test soils. We also quantified the prometryne sorption and desorption behavior in soils, which arose from the application of Triton X-100 (TX100), a nonionic surfactant and change in pH. Application of TX100 led to a general decrease in prometryne sorption to the soils and an increase in desorption from the soils when applied in dosages of the critical micella concentration (CMC) 0.5, 1 and 2. At the concentration below the CMC, the non-ionic surfactant showed a tendency to decrease prometryne sorption and desorption. It appeared that TX100 dosages above CMC were required to effectively mobilize prometryne. Results indicate that the maximum prometryne sorption and minimum prometryne desorption in soils were achieved when the solution pH was near its pK_a. Finally, the influence of TX100 on the mobility of prometryne in soils using soil thin-layer chromatography was examined.     

Partitioning of chloroaromatic compounds between the aqueous phase and dissolved and particulate soil organic matter at chlorophenol contaminated sites

The retention and mobility of hydrophobic organic contaminants (HOCs) in soil is mainly determined by hydrophobic partitioning to dissolved and particulate organic matter (DOM and POM, respectively). The aqueous phase, DOM, and POM fractions were extracted and separated from soils at three sites contaminated with technical chlorophenol formulations. Concentrations of chlorophenols (CP), polychlorinated phenoxyphenols (PCPP), polychlorinated diphenyl ethers (PCDE) and polychlorinated dibenzo-p-dioxins and furans (PCDD/F) were determined. The partitioning to POM, in relation to DOM, increased in all three soils with increasing hydrophobicity in the order CP < PCPP ~ PCDE ~ PCDF < PCDD. Differences in partitioning to DOM (logK(DOC)) and POM (logK(POC)) could not be explained by differences in gross organic C chemistry. Black carbon did not contribute significantly to the sorption of PCDDs, whereas >70% wood fibre in one soil resulted in a decrease of logK(POC) of 0.5 units for CPs and PCDDs. We conclude that logK(OC) for both DOM and POM need to be explicitly determined when the retention and mobility of HOCs is described and modelled in soils.     

Sorption of hydrophobic organic compounds onto organoclays

The behavior and fate of nonionic hydrophobic organic compounds (HOCs) in the environment are mainly controlled by their interactions with various components of soils and sediments. Due to their large surface area and abundance in many soils, smectites may greatly influence the fate and transport of the contaminants in the environment. In our experiments, HOC sorption by hexadecyltrimethylammonium (HDTMA)-modified smectite linearly increased with the amount of HDTMA added to the clay. However, tetramethylammonium (TMA)- and dodecyltrimethylammonium (DTMA)-modified smectites showed not only inferiority in their sorption of HOC compared with the HDTMA-smectite, but also a partially decreased HOC sorption at specific surfactant loading levels. This means that the sorption of organoclays for organic contaminants was significantly influenced by the amount and size of the surfactants added on the clay. In addition, it seems that the interlayer structure (e.g., pore size) formed at each surfactant loading level plays an important role to adsorb HOC in different amount.     

Effect of clays, metal oxides, and organic matter on rhamnolipid biosurfactant sorption by soil

Rhamnolipids produced by Pseudomonas aeruginosa have been proposed as soil washing agents for enhanced removal of metal and organic contaminants from soil. A potential limitation for the application of rhamnolipids is sorption by soil matrix components. The objective of this study is to empirically determine the contribution of representative soil constituents (clays, metal oxides, and organic matter) to sorption of the rhamnolipid form most efficient at metal complexation (monorhamnolipid). Sorption studies show that monorhamnolipid (R1) sorption is concentration dependent. At low R1 concentrations that are relevant for enhancing organic contaminant biodegradation, R1 sorption followed the order: hematite (Fe(2)O(3))>kaolinite>MnO(2) approximately illite approximately Ca-montmorillonite>gibbsite (Al(OH)(3))>humic acid-coated silica. At high R1 concentrations, relevant for use in complexation/removal of metals or organics, R1 sorption followed the order: illite>humic acid-coated silica>Ca-montmorillonite>hematite>MnO(2)>gibbsite approximately kaolinite. These results allowed prediction of R1 sorption by a series of six soils. Finally, a comparison of R1 and R2 (dirhamnolipid) shows that the R1 form sorbs more strongly alone than when in a mixture of both the R1 and R2 forms. The information presented can be used to estimate, on an individual soil basis, the extent of rhamnolipid sorption. This is important for determining: (1) whether rhamnolipid addition is a feasible remediation option and (2) the amount of rhamnolipid required to efficiently remove the contaminant.     

Sorption and desorption kinetics of diuron,fluometuron, prometryn and pyrithiobac sodium in soils

Abstract

The sorption and desorption characteristics of four herbicides (diuron, fluometuron, prometryn and pyrithiobac‐sodium) in three different cotton growing soils of Australia was investigated. Kinetics and equilibrium sorption and desorption isotherms were determined using the batch equilibrium technique. Sorption was rapid (> 80% in 2 h) and sorption equilibrium was achieved within a short period of time (ca 4 h) for all herbicides. Sorption isotherms of the four herbicides were described by Freundlich equation with an r² value > 0.98. The herbicide sorption as measured by the distribution coefficient (K_d) values ranged from 3.24 to 5.71 L/kg for diuron, 0.44 to 1.13 L/kg for fluometuron, 1.78 to 6.04 L/kg for prometryn and 0.22 to 0.59 L/kg for pyrithiobac‐sodium. Sorption of herbicides was higher in the Moree soil than in Narrabri and Wee Waa soils. When the K_d values were normalised to organic carbon content of the soils (K_oC), it suggested that the affinity of the herbicides to the organic carbon increased in the order: pyrithiobac‐sodium < fluometuron < prometryn < diuron. The desorption isotherms were also adequately described by the Freundlich equation. For desorption, all herbicides exhibited hysteresis and the hysteresis was stronger for highly sorbed herbicides (diuron and prometryn) than the weakly sorbed herbicides (fluometuron and pyrithiobac‐sodium). Hysteresis was also quantified as the percentage of sorbed herbicides which is not released during the desorption step ω = [n_ad / n_de ‐1] x 100). Soil type and initial concentration had significant effect on ω. The effect of sorption and desorption properties of these four herbicides on the off‐site transport to contaminate surface and groundwater are also discussed in this paper.     

Pesticide adsorption on a calcareous soil modified with sewage sludge and quaternary alkyl-ammonium cationic surfactants

BACKGROUND, AIM AND SCOPE: Pesticides are often found in soil as a result of their application to control pests. They can be transported on soil particles to surface waters or they can lixiviate and reach other environmental compartments. Soil modification with amendments, such as sewage sludge, and with surfactants, h been proposed to reduce pesticide environmental fate. METHODS: The sorption of atrazine, methidathion and diazinon using the batch technique has been studied on non-modified soil and soil modified with sewage sludge and cationic surfactants, as well as the effect of their addition on soil properties such as organic carbon (OC) content and exchange cations. RESULTS AND DISCUSSION: The OC content of the surfactant modified soils was the highest with the surfactant with the longest hydrocarbon chain (hexadecyltrimethyl ammonium bromide, HDTMA). The results of the OC content run in parallel with the increase in pesticide retention. When the sorption was n malized to soil OC content, the retention induced by addition of HDTMA was still the highest, which is an indication that the organic matter derived from the organic cations is a more effective medium to retain dissolved contaminants, than organic matter from native soil. The addition of sewage sludge to the soil did only result in a slight increase of the soil CEC and, hence, moderately affected the ability of the cationic surfactant to retain the pesticides. CONCLUSIONS: The addition of cationic surfactants to soil would possibly reduce the movement to groundwater of atrazine, methidathion and diazinon. In the case of HDTMA, the decrease in sorption at high surfactant loadings was very slow, being that the surfactant was able to retain the pesticides at concentration values which clearly exceeded the monolayer coverage. RECOMMENDATIONS AND PERSPECTIVES: Contamination by pesticides, which are present in the soil due to their direct input in this medium or to spills or illegal tipping, may be hindered from migration to groundwater by application of a cationic surfactant.     

Correlations of nonlinear sorption of organic solutes with soil/sediment physicochemical properties

The estimation of solute sorptive behaviors is essential when direct sorption data are unavailable and will provide a convenient way to assess the fate and the biological activity of organic solutes in soil/sediment environments. In this study, the sorption of 2,4-dichlorophenol (2,4-DCP) on 19 soil/sediment samples and the sorption of 13 organic solutes on one sediment were investigated. All sorption isotherms are nonlinear and can be described satisfactorily by a simple dual-mode model (DMM): q(e)=KpCe+Q0 . bCe/(1+bCe), where Kp (mlg(-1)) is the partition coefficient; Ce (microgml(-1)) is the equilibrium concentration; Q0 (microgg(-1)) is the maximum adsorption capacity; Q0 . b (mlg(-1)) is the Langmuir-type isotherm slope in the low concentration (Henry's law) range and b (mlmicrog(-1)) is a constant related to the affinity of the surface for the solute. Based on these nonlinear sorption isotherms and similar other nonlinear isotherms, it is observed that, for both polar 2,4-DCP and nonpolar phenanthrene, Kp, Q0 and Q0 . b are linearly correlated with soil/sediment organic carbon content (f(oc) in the range of 0.118-53.7%). The results indicate that the nonlinear sorption of organic solutes results primarily from interactions with soil/sediment organic matter. The K*oc K*oc=Kp/f(oc)), Qoc (Qoc=Q0/f(oc)), Loc (Loc=Q0 . b/f(oc)) and b for a given organic solute with different soils/sediments are largely invariant. Furthermore, logK*oc, logb and logLoc for various organic solutes are correlated significantly with the solute logKow or logSw (logKow in the range of 0.9 to 5.13 and logSw in the range of -6.176 to -0.070). A fundamental empirical equation was then established to calculate approximately the nonlinear sorption from soil/sediment f(oc) and solute Sw for a given solute equilibrium concentration.     

Sorption-Desorption of Atrazine and Diuron in Soils from Southern Brazil

The objective of this study was to investigate the behavior of sorption and desorption of the herbicides atrazine (6-chloro-N ²-ethyl-N ⁴-isopropyl-1,3,5-triazine-2,4-diamine) and diuron [3-(3,4-dichlorophenyl)-1,1-dimethyleurea] in soil samples from a typical lithosequence located in the municipality of Mamborê (PR), southern Brazil. Five concentrations of ¹⁴C-atrazine and ¹⁴C-diuron were used for both herbicides (0.48, 0.96, 1.92, 3.84, and 7.69 mg L^?1). Sorption of both herbicides correlated positively with the organic carbon and clay content of the soil samples. Sorption isotherms were well described by the Freundlich model. The slope values of the isotherm (N) ranged from 0.84 to 0.90 (atrazine) and from 0.75 to 0.79 (diuron) for the lithosequence samples. Sorption of diuron was high regardless of the soil texture or the concentration added. The desorption isotherms for atrazine and diuron showed good fit to the Freundlich equation (R ² ≥ 0,87). Atrazine slope values for the desorption isotherms were similar for the different concentrations and were much lower than those observed for the sorption isotherms. Significant hysteresis was observed in the herbicide desorption. When the two herbicides were compared, it was found that diuron (N = 0.06–0.22) presented more pronounced hysteresis than atrazine. The results showed that, quantitatively, a greater atrazine fraction applied to these soils remains available to be leached in the soil profile, as compared to diuron.     

Sorption-desorption behavior of metsulfuron-methyl and sulfosulfuron in soils

Sorption of metsulfuron-methyl and sulfosulfuron were studied in five Indian soils using batch sorption method. Freundlich adsorption equation described the sorption of herbicides with K_f (adsorption coefficient) values ranging between 0.21 and 1.88 (metsulfuron-methyl) and 0.37 and 1.17 (sulfosulfuron). Adsorption isotherms were L-type suggesting that the herbicides sorption decreased with increase in the initial concentration of the herbicide in the solution. The K_f for metsulfuron-methyl showed good positive correlation with silt content (significant at p = 0.01) and strong negative correlation with the soil pH (significant at p = 0.05) while sorption of sulfosulfuron did not correlate with any of the soil parameter. Desorption of herbicides was concentration dependent and, in general, sulfosulfuron showed higher desorption than the metsulfuron-methyl. The study indicates that these herbicides are poorly sorbed in the Indian soil types and there may be a possibility of their leaching to lower soil profiles.