Chemical properties of heavy metals in typical hospital waste incinerator ashes in China

Incineration has become the main mechanism for hospital waste (HW) disposal in China after the outbreak of Severe Acute Respiratory Syndrome (SARS) in 2003. However, little information is available on the chemical properties of the resulting ashes. In the present study, 22HW ash samples, including 14 samples of bottom ash and eight samples of fly ash, were collected from four typical HW incineration plants located across China. Chemical analysis indicated that the HW ashes contained large amounts of metal salts of Al, Ca, Fe, K, Mg, Na with a concentration range of 1.8-315gkg(-1). Furthermore, the ashes contained high concentrations of heavy metals such as Ag, As, Ba, Bi, Cd, Cr, Cu, Mn, Ni, Pb, Ti, Sb, Sn, Sr, Zn with a vast range of 1.1-121,411mgkg(-1), with higher concentrations found in the fly ash samples. Sequential extraction results showed that Ba, Cr, Ni and Sn are present in the residual fraction, while Cd existed in the exchangeable and carbonate fractions. As, Mn, Zn existed in the Fe-Mn oxide fraction, Pb was present in the Fe-Mn oxide and residual fractions, and Cu was present in the organic matter fraction. Furthermore, toxicity characteristic leaching procedure (TCLP) results indicated that leached amounts of Cd, Cu and Pb from almost all fly ash samples exceeded the USEPA regulated levels. A comparison between the HW ashes and municipal solid waste (MSW) ash showed that both HW bottom ash and fly ash contained higher concentrations of Ag, As, Bi, Cd, Cr, Cu, Pb, Ti, and Zn. This research provides critical information for appropriate HW incineration ash management plans.     

Enhancing performance and durability of slag made from incinerator bottom ash and fly ash

This work presents a method capable of melting the incinerator bottom ash and fly ash in a plasma furnace. The performance of slag and the strategies for recycling of bottom ash and fly ash are improved by adjusting chemical components of bottom ash and fly ash. Ashes are separated by a magnetic process to improve the performance of slag. Analytical results indicate that the air-cooled slag (ACS) and magnetic-separated slag (MSS) have hardness levels below 590 MPa, indicating fragility. Additionally, the hardness of crystallized slag (RTS) is between 655 and 686 MPa, indicating toughness. The leached concentrations of heavy metals for these three slags are all below the regulatory limits. ACS appears to have better chemical stability than MSS, and is not significantly different from RTS. In the potential alkali-silica reactivity of slag, MSS falls on the border between the harmless zone and the potentially harmful zone. ACS and RTS fall in the harmless zone. Hence, the magnetic separation procedure of ashes does not significantly improve the quality of slag. However, RTS appears to improve its quality.     

Comparison of leaching characteristics of heavy metals from bottom and fly ashes in Korea and Japan

The objective of this research was to compare the leaching characteristics of heavy metals such as cadmium, chromium, copper, nickel, lead, etc., in Korean and Japanese municipal solid waste incineration (MSWI) ash. The rate of leaching of heavy metal was measured by KSLT and JTL-13, and the amount of heavy metals leached was compared with the metal content in each waste component. Finally, bio-availability testing was performed to assess the risks associated with heavy metals leached from bottom ash and fly ash. From the results, the value of neutralization ability in Japanese fly ash was four times higher than that in Korean fly ash. The reason was the difference in the content of Ca(OH)(2) in fly ash. The amount of lead leached exceeded the regulatory level in both Japanese and Korean fly ash. The rate of leaching was relatively low in ash with a pH in the range of 6-10. The bio-availability test in fly ash demonstrated that the amount of heavy metals leached was Pb>Cd>Cr, but the order was changed to Pb>Cr>Cd in the bottom ash. The leaching concentration of lead exceeded the Japanese risk level in all fly ashes from the two countries, but the leaching concentration of cadmium exceeded the regulatory level in Korean fly ash only.     

Concentrations of heavy metals in fly ash from a coal-fired power plant with respect to the new Finnish limit values

In Finland, the new limit values for heavy metals in fertilizers used in agriculture and in forestry came into force in March 2007, and for materials used as earth construction agents, in June 2006. From the utilization point of view, it was notable that the total heavy metal concentrations (Cd, Cu, Pb, Cr, Mo, Zn, As, Ni, Ba, and Hg) in fly ash from a coal-fired power plant were lower than those limit values. The concentrations of the easily soluble elements Ca, Mg, Na, P, and Zn in the fly ash were between 3.5 and 35 times higher than those found in the coarse mineral soils of Finland. Fly ash is a potential agent for soil remediation and for improving soil fertility. If inorganic materials and by-products are utilized in earthworks, the content of harmful compounds must be low and the harmful components must be tightly bound to the matrix. Therefore, a five-stage sequential extraction procedure was used to evaluate the extractability of different elements in fly ash into the following fractions: (1) the water-soluble fraction, (2) the exchangeable fraction (CH₃COOH), (3) the easily reduced fraction (NH₂OH-HCl), (4) the oxidizable fraction (H₂O₂ + CH₃COONH₄), and (5) the residual fraction (HF + HNO₃ + HCl).     

Leachability of municipal solid waste ashes in simulated landfill conditions

In Japan the volume of municipal solid waste is reduced by incineration, with fly ash and bottom ash disposed in controlled landfills. The leachability of anions and heavy metal cations, Zn, Cu and Pb, from MSW fly ash and bottom ash at different pHs was examined using batch- and column-leaching tests. The MSW ashes had a high capacity for neutralizing acids. Behaviour during leaching depended on the pH of the solution. For the volumes applied, the leachabilities of MSW fly ash were very similar at pHs from 3 to 6. Due to its amphoteric nature, Pb is leachable at pHs of approximately 10 or more, with leachate concentrations of about 3 and 3-10mg/L for the fly ash and bottom ash, respectively, much higher than for Zn and Cu. Pb concentrations for most leaching solutions were 1 and 3mg/L for the fly ash and bottom ash, respectively. Zn, and Cu leached at low concentrations for solutions of pH 3-6. Na and K ions leached at high concentrations of approximately 5000 mg/L in the first batch leaching test, decreasing to 10mg/L by the fourth leach. Ca and Mg ions leached more gradually than Na and K. Cl(-) and SO(4)(2+) ions were the major anions in the MSW ash. The high pH and cation leaching are expected to have negative impacts on the performance of clay liners.     

Sustainable alkali-activated binders with municipal solid waste incineration ashes as sand or fly ash replacement

The present study investigates the feasibility of using two types of municipality solid wastes incineration ashes, namely, fly ash and bottom ash in the production of sustainable alkali-activated binder. The ashes are collected from the incineration plant and characterized to determine their particle size distribution, specific gravity, chemical composition, and heavy metals content. The ashes are then used as either fly ash or sand replacement with five replacement ratios 0%, 5%, 10%, 15%, and 20% to produce the binder. The produced binder are characterized in terms of strength, workability, density, water absorption, thermal conductivity and stability, chemical composition, and heavy metals content. The results reflect the ability of producing sustainable alkali-activated binder with small dosage of MSWI ashes as either fly ash or sand replacement without negatively affecting its strength, workability, density, and water absorption. The ashes enhance the thermal insulation capability of the binder.

     

Belgian MSWI fly ashes and APC residues: a characterisation study

Municipal Solid Waste Incineration (MSWI) produces different sorts of residues, bottom ash, fly ashes and Air Pollution Control (APC) residues. Generally, fly ashes and APC residues are mixed at the MSWI plant and manage as a sole residue. In this study, fly ashes and APC residues have been sampled separately at different Belgian MSWI plant and analysed by X-ray fluorescence in order to highlight the composition differences that may appear between the solids. Ca and Cl are found to be the major elements in most of the samples. Lithophilic elements, such as Al and Si, are richer in furnace and boiler ashes, as can be expected. Leaching tests also show differences between the residues; leachates from furnace and boiler ashes are alkaline while those from bag filter residues present a pH value of 6, which impacts the leaching of heavy metals (Pb and Zn). The results suggest that it could be advantageous to manage fly ashes and APC residues separately by adjusting the treatment to their specificities.     

Effect of sintering temperature on the properties and leaching of incinerator bottom ash.

The fine particle size fraction of municipal solid waste incinerator bottom ash is often problematic because reuse applications for this material are limited. In these experiments incinerator bottom ash with a particle size of less than 8 mm was processed using conventional ceramic production techniques involving wet milling, drying, compacting and sintering. The effect of sintering temperature on the sintered density, microstructure, acid neutralization capacity (ANC) and the release of metal ions as a function of leachate pH are reported. Sintering at 1080 degrees C produced samples with maximum density. This material contained diopside (CaMgSi2O6), clinoenstatite (Mg2Si2O6) and wollastonite (CaSiO3) as the major crystalline phases. The acid neutralization capacity of sintered samples is significantly lower than milled bottom ash, and further reduces as the sintering temperature increases. This is associated with reduced leaching of Ca from sintered ash samples under all leachate pH conditions. Heavy metals present in the incinerator bottom ash included Cr, Cu, Ni, Zn, Cd and Pb. Sintering under optimum conditions reduced the leachable fraction of these metals under aggressive acid conditions (leachate pH 3) by factors ranging from 90% for Ni to greater than 99% for Cr, Cd, Zn and Pb.     

Metal leachability, heavy metals, polycyclic aromatic hydrocarbons and polychlorinated biphenyls in fly and bottom ashes of a medical waste incineration facility

Medical waste from hospitals and other healthcare institutions has become an imperative environmental and public safety problem. Medical waste in Greece has become one of the most urgent environmental problems, because there are 14,000 tons produced annually, of which only a small proportion is incinerated. In the prefecture of Attica there is only one modern municipal medical waste incinerator (started 2004) burning selected infectious hospital waste (5-6 tons day(-1)). Fly and bottom residues (ashes) are collected and stored temporarily in barrels. High values of metal leachability prohibit the landfilling of these ashes, as imposed by EU directives. In the present study we determined quantitatively the heavy metals and other elements in the fly and bottom ashes of the medical waste incinerator, by inductively coupled plasma emission spectrometry (ICP) and by energy dispersive X-ray analysis (EDAX). Heavy metals, which are very toxic, such as Pb, Cd, Ni, Cr, Cu and Zn were found in high concentrations in both fly and bottom ashes. Metal leachability of fly and bottom ashes by water and kerosene was measured by ICP and the results showed that toxic metals in both ashes, such as Pb, Cr, Cd, Cu and Zn, have high leaching values. These values indicate that metals can become soluble and mobile if ash is deposited in landfills, thus restricting their burial according to EU regulations. Analysis of polychlorinated biphenyls and polycyclic aromatic hydrocarbons in fly and bottom ashes showed that their concentrations were very low. This is the first known study in Greece and the results showed that incineration of medical waste can be very effective in minimizing the most hazardous and infectious health-care waste. The presence of toxic metals with high leachability values remains an important draw back of incineration of medical waste and various methods of treating these residues to diminish leaching are been considered at present to overcome this serious technical problem.     

Briquetting of charcoal from sugar-cane bagasse fly ash (scbfa) as an alternative fuel

Brazil is the largest worldwide producer of alcohol and sugar from sugar-cane and has an extensive alternative program for car fuel which is unique. The objective of this work is to offer one management option of a solid residue produced by this industrial segment. The pressed sugar-cane bagasse is burned to produce steam and electricity by cogeneration. The combustion yields both bottom and fly ashes which contain high amounts of silicon oxide as a major component. Fly ash which contains a high volume (>30% by weight) of charcoal was used in this work. The ash was sieved to separate the thick charcoal from inorganic materials which are concentrated in the thinner fraction. The briquettes were hand pressed using charcoal mixed with a binder (starch) obtained from cassava flour (a tropical root). The results (density, mechanical resistance) obtained with 8% by weight of starch binder are presented here. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were used to characterize the ashes and the briquettes. The results show that sugar-cane bagasse fly ash (SCBFA) can be used to produce briquettes with an average density of 1.12 g cm^?3 and an average calorific value of 25,551 kJ/kg.     

Chloride extraction for quality improvement of municipal solid waste incinerator ash for the concrete industry.

Coal ash from power stations has long been used successfully in the cement industry as binders in several Portland formulations. This is not the case for municipal solid waste (MSW) ash as chloride concentrations, ranging from 10 to 200 g kg(-1) dry weight in the bottom and fly ash, respectively, exceed the maximum allowable concentration in most cement mixtures. To reduce chloride content in MSW bottom ash, a laboratory investigation was carried out based on the exhaustive washing in tap water. The influence of operative parameters such as temperature, granulometric properties and solid/liquid ratio of extraction was evaluated. In addition to optimization of the mentioned operative parameters for full-scale application, the paper gives preliminary indications on mechanistic aspects of the washing operation.     

Some limitations of sluiced fly ash as a liming material for acidic soils

Innovative methods are currently being sought to safely utilize and reduce the amount of sluiced fly ash stored in on-site facilities at thermal electric power facilities in Ontario, Canada. The objective of this study was to investigate the possibility of utilizing sluiced fly ash as a liming material on acidic soils. A greenhouse experiment was established to examine the influence of the ash on soil pH values and the yield and chemical composition of corn, soybeans, wheat and alfalfa grown on amended soil.The sluiced ash had an initial pH value of 9.1 (1:1 H₂O) and contained an equivalent CaCO₃ content of 11.5% (±0.2%) based on total content of Ca and Mg in the ash. Fly ash was applied at rates of up to 167 tonnes ha⁻¹ to samples of the surface horizon (0–15 cm) of an acidic clay textured soil found local to the power plant. Application of fly ash increased soil pH values but a high concentration of boron in the added ash limited plant growth. Results indicated that the sluiced ash could be used as a liming material at application rates of up to 110 tonnes ha⁻¹, on acidic, clay textured soils provided boron tolerant crops such as alfalfa were grown. Further research is required to establish the potential for leaching of boron to ground water and to determine the potential for plant uptake of other trace elements such as As and Se.     

Water washing effects on metals emission reduction during municipal solid waste incinerator (MSWI) fly ash melting process

This study investigated that water washing effects on the metals emission reduction in melting of municipal solid waste incinerator (MSWI) fly ash. Experimental conditions were conducted at liquid-to-solid (L/S) ratio 10, 20, and 100 for water-washing process and its subsequent melting treatment at 1450 °C for 2 h. The simple water-washing process as a pre-treatment for MSWI fly ash can remove most of the chlorides, leachable salts, and amphoteric heavy metals from the MSWI fly ash, resulting in the washed ash having lowered chlorine content. MSWI fly ashes washed by L/S ratio 10 and above that were melted at 1450 °C produced slag containing relatively high vitrificaton ratio of Cu and Pb. Besides, the vitrification ratios of Na, K, Ca, and Mg in washed MSWI fly ash were also higher than that of MSWI fly ash. The results indicated that washed MSWI fly ash can reduce the emission of metallic chlorides during its subsequent melting treatment.     

A study of disposed fly ash from landfill to replace Portland cement

The landfills of fly ash are the problem of all power plants because this disposed fly ash is not used in any work. This research studies the potential of using disposed fly ashes which have disposal time of 6-24 months from the landfill of Mae Moh power plants in Thailand to replace Portland cement type I. Median particle sizes of disposed fly ashes between 55.4 and 99.3 microm were ground to reduce the sizes to about 7.1-8.4 microm. Both original and ground disposed fly ashes were investigated on physical and chemical properties. Compressive strengths of disposed fly ash mortars were determined when Portland cement type I was replaced by disposed fly ashes at the rate of 10%, 20%, and 30% by weight of cementitious material (Portland cement type I and disposed fly ash). The results presented that most particles of original disposed fly ashes were solid and sphere with some irregular shape while those of ground disposed fly ashes were solid and irregular shape. CaO and LOI contents of disposed fly ashes with different disposal times had high variation. The compressive strengths of original disposed fly ash mortars were low but those of ground disposed fly ash mortars at the age of 7 days were higher than 75% of the standard mortar and increased to be higher than 100% after 60 days. From the results, it could be concluded that ground disposed fly ashes were excellent pozzolanic materials and could be used as a partial replacement of cement in concrete, even though they were exposed to the weather for 24 months.     

Chemical changes in different types of coal ash during prolonged,large scale,contact with seawater

In this study, we followed the chemical changes occurring in coal ash exposed to prolonged (300 days), large scale, contact with running seawater. Four major components (Al, Ca, Mg, Fe) and seven minor and trace elements (Cd, Cr, Cu, Mn, Zn, Pb, Hg) were measured in four coal ash types: fly and bottom ash freshly obtained from coal-fired power plant, and old ash (crushed and blocks) recovered from the sea after 3-5 years contact with seawater. Changes occurred in the chemical composition of the coal ash along the experiment: Fe increased in fresh ash, Al increased in old ash and Ca increased in all ash types except old ash blocks. Cu and Hg decreased in fresh fly ash while Cr increased, Cd decreased in all ash types except bottom ash, and Mn decreased in bottom ash. Most of the changes occurred in the fresh fly ash, and not in the old ash, indicating equilibrium after prior exposure to seawater. In addition, more changes occurred in fresh fly ash than in bottom ash, emphasizing the differences between the two ash types. While the changes in the concentrations of the major elements may be an indication of the integrity of the ash matrix, the only elements of environmental significance released to the environment were Hg and Cd. However, calculated seawater concentrations were much lower than seawater quality criteria and therefore the coal ash was considered suitable for marine applications concerning seawater quality.     

Comparative study on the characteristics of fly ash and bottom ash geopolymers

This research was conducted to compare geopolymers made from fly ash and ground bottom ash. Sodium hydroxide (NaOH) and sodium silicate (Na(2)SiO(3)) solutions were used as activators. A mass ratio of 1.5 Na(2)SiO(3)/NaOH and three concentrations of NaOH (5, 10, and 15M) were used; the geopolymers were cured at 65 degrees C for 48 h. A Fourier transform infrared spectrometer (FT-IR), differential scanning calorimeter (DSC), and scanning electron microscope (SEM) were used on the geopolymer pastes. Geopolymer mortars were also prepared in order to investigate compressive strength. The results show that both fly ash and bottom ash can be utilized as source materials for the production of geopolymers. The properties of the geopolymers are dependent on source materials and the NaOH concentration. Fly ash is more reactive and produces a higher degree of geopolymerization in comparison with bottom ash. The moderate NaOH concentration of 10 M is found to be suitable and gives fly ash and bottom ash geopolymer mortars with compressive strengths of 35 and 18 MPa.     

Effect of fly ash addition on the removal of hydrogen sulfide from biogas and air on sewage sludge-based composite adsorbents

Desulfurization adsorbents were prepared from the mixtures of various compositions of New York City sewage sludge and fly ashes from SASOL, South Africa, by pyrolysis at 950 degrees C. The resulting materials were used as adsorbents of hydrogen sulfide from simulated dry digester gas mixture or moist air. The adsorbents before and after H(2)S removal were characterized using adsorption of nitrogen, elemental analysis, pH measurements, XRF, XRD, and thermal analysis. It was found that the addition of fly ash decreases the desulfurization capacity in comparison with the sewage sludge-based materials. The extent of this decrease depends on the type of ash, its content and the composition of challenging gas. Although the presence of CO(2) deactivates some adsorption sites to various degrees depending on the sample composition, the addition of ashes has a more detrimental effect when the adsorbents are used to remove hydrogen sulfide from air. This is likely the result of hydrophobicity of ashes since the H(2)S removal capacity was found to be strongly dependent on the reactivity towards water/water adsorption. On the other hand, the addition of ashes strongly decreases the porosity of materials where sulfur, as a product of hydrogen sulfide oxidation, can be stored.     

Sintering characteristics of CaO-rich municipal solid waste incineration fly ash through the addition of Si/Al-rich ash residues

Thermal treatment is a promising technology for the fast disposal of hazardous municipal solid waste incineration (MSWI) fly ash in China. However, fly ash produced in grate incinerator (GFA) is rich in CaO and chlorides, which promote the formation of toxic hexavalent chromium [Cr(VI)] and ash agglomeration during the thermal process, inhibiting the thermal disposal of GFA. In this study, sintering characteristics of CaO-rich GFA were improved by adding Si/Al-rich MSWI ash residues. According to the results, ash agglomeration was well suppressed during thermal treatment of the mixed ash. Si/Al/Fe-compounds competed with un-oxidized Cr-compounds to react with CaO and suppressed Cr(VI) formation. Meanwhile, chlorides in GFA facilitated heavy metal volatilization from added ashes to the secondary fly ash, favoring the recovery of these metals. Ca-aluminosilicates was found as the main mineral phase in the thermally treated mixed ash, which has attractive potential for applications. The formation of the aluminosilicates made the heavy metals that remained in the treated mixed ash more stable than the thermally treated single ash.     

Ceramic processing of incinerator bottom ash

The <8 mm fraction of aged incinerator bottom ash from a commercial incinerator (energy from waste) plant has been collected at regular intervals, characterised and processed to form ceramic materials. Ashes were sieved, wet ball milled, dried, compacted and sintered at temperatures between 1080 and 1115 degrees C. Variations in the chemical composition and mineralogy of the milled ash, and the mineralogy, physical properties and leaching of sintered products have been assessed. Milling produces a raw material with consistent chemical and mineralogical composition with quartz (SiO(2)), calcite (CaCO(3)), gehlenite (Ca(2)Al(AlSi)O(7)) and hematite (Fe(2)O(3)) being the major crystalline phases present. Different batches also milled to give consistent particle size distributions. Sintering milled incinerator bottom ash at 1110 degrees C produced ceramics with densities between 2.43 and 2.64 g/cm(-3) and major crystalline phases of wollastonite (CaSiO(3)) and diopside (CaMgSi(2)O(6)). The sintered ceramics had reduced acid neutralisation capacity compared to the as-received ash and exhibited reduced leaching of Ca, Mg, Na and K under all pH conditions. The leaching of heavy metals was also significantly reduced due to encapsulation and incorporation into glassy and crystalline phases, with Cu and Al showing greatly reduced leaching under alkali conditions.     

High fire resistance in blocks containing coal combustion fly ashes and bottom ash

Fire resistance recycled blocks, containing fly ash and bottom ash from coal combustion power plants with a high fire resistance, are studied in this paper by testing different compositions using Portland cement type II, sand, coarse aggregate and fly ash (up to 50% of total weight) and bottom ash (up to 30% of total weight). The fire resistance, physical-chemical (density, pH, humidity, and water absorption capacity), mechanical (compressive and flexural strength), and leaching properties are measured on blocks made with different proportions of fly ash and bottom ash. The standard fire resistance test is reproduced on 28 cm-high, 18 cm-wide and 3 cm-thick units, and is measured as the time needed to reach a temperature of 180 °C on the non-exposed surface of the blocks for the different compositions.The results show that the replacement of fine aggregate with fly ash and of coarse aggregate with bottom ash have a remarkable influence on fire resistance and cause no detriment to the mechanical properties of the product. Additionally, according to the leaching tests, no environmental problems have been detected in the product. These results lead to an analysis of the recycling possibilities of these by-products in useful construction applications for the passive protection against fire.