Wind power potential assessment for three buoys data collection stations in the Ionian Sea using Weibull distribution function

The present article utilizes wind measurements from three buoys data collection stations in Ionian Sea to study the wind speed and power characteristics using the Weibull shape and scale parameters. Specifically, the site dependent, annual, and monthly mean patterns of mean wind speed, Weibull parameters, frequency distribution, most probable wind speed, maximum energy carrying wind speed, wind power density and wind energy density characteristics have been analyzed. The Weibull distribution was found to represent the wind speed distribution with more than 90% accuracy, in most of the cases. Moreover, the correlation between the percentages of times the wind speed was above cut-in-speed and the measured mean wind speed for the three selected sites, as the correlation between the aforementioned percentages and the scale parameter c were examined and were found linear. At all these sites, no definite increasing or decreasing trends in annual mean wind speed values could be detective over the data reporting period. The mean values of wind speed, scale parameter, most probable wind speed, maximum energy carrying wind speed, wind power and wind energy density values showed higher values during winter time and lower in summer time in Pylos and Zakynthos. Moreover, Pylos and Zakynthos were found to be the best sites from wind power harnessing point of view.     

A convective wind resource model for Solar Vortex power generation

ABSTRACT

Climate change has increased the need for clean, nonpolluting energy sources to decrease dependence on fossil fuels. Alternative energy sources, mainly solar and horizontal wind, have been the primary focus for producing clean energy. New technologies are being developed, such as the Solar Vortex (SoV), which was developed at the Georgia Institute of Technology, and relies on a vertical wind resource to generate power. The National Renewable Energy Lab (NREL) has resource models representing solar and horizontal wind resources across the 48 United States. This research developed a vertical wind resource model that is comparable in resolution to NREL’s solar and horizontal wind resource models and uses the model for estimating power output for the SoV. This model complements NREL’s existing resource models and supports the deployment of an additional clean energy generation technology. The model was applied to Mesa, Arizona to find feasible sites for a small-scale vertical wind farm.     

Ecosystem Services and Economic Assessment of Land Uses in Urban and Periurban Areas

Environmental Management - This work quantified ecosystem services (ES) and the geographic gross product (GGP) at municipal level in the Metropolitan Region of Buenos Aires (MRBA), Argentina. The...     

Wind energy potential analysis for Thailand: Uncertainty from wind maps and sensitivity to turbine technology

Rapid development of wind energy has been witnessed in Thailand. However, different wind resource maps (over land) have brought great uncertainty to wind energy planning. Here, four important mesoscale wind maps were considered: DEDP (2001), World Bank (2001), Manomaiphiboon et al. (2010) of JGSEE, and DEDE (2010). The wind maps were first harmonized to a common grid at 100 m and then compared. The earlier wind maps (DEDP and World Bank) are shown to represent the lower and upper limits of predicted speed, respectively, while JGSEE and DEDE tend to be more moderate with predictions statistically closer to observations. A consolidated wind map was constructed based on their median and shown to have the best prediction performance. It was then used for the technical potential analysis, in which three large (2-MW) turbine models (two conventional and one designed for low wind speed) were considered. By GIS techniques, any land areas not feasible for large wind turbines were excluded, and the corresponding overall onshore technical potential ranges between 50 and 250 GW, depending on map and turbine model. Considering only economically feasible turbines (with capacity factors of 20%) and the median-based map, the final technical potential equals 17 GW when using the low-wind-speed model but is reduced to 5 GW with the conventional models, adequately meeting the national wind energy target of 3 GW by the year 2036. The results suggest a strong sensitivity of estimated technical potential to turbine technology and a suitability of low-wind-speed turbines for wind conditions in Thailand.     

Wind energy development in Ontario: a process/product paradox

The Province of Ontario is aggressively pursuing renewable energy development, but not without significant turbulence. Ontario's Green Energy Act (2009) reflects this aggressive pursuit, and is aimed at making the province a global leader in renewable energy development. Wind energy is an integral but controversial part of these commitments. While several installations have been built or announced, conflicts surrounding the development of the technology continue to grow. This article documents, analyses and interprets media coverage in order to understand public discourse potentially driving support for and resistance to wind energy development (WED) in Ontario. Contrary to numerous studies which have elucidated public attitudes towards WED, the media discourse analysed suggests that roadblocks to public acceptance of the technology are more rooted in the development process (renewable energy policies and their implementation) rather than the products of WED (wind turbines). The study highlights the need for increased procedural justice to ameliorate feelings of unfairness which play a key role in fuelling resistance to the technology.     

EVALUATING THE ACCURACY OF RAINFALL CATCH BY THREE DIFFERENT GAGES1

ABSTRACT: A U.S. standard gage, a weighing-type recording gage, a standard gage fitted with an Alter windshield, and a pit gage were installed to evaluate the accuracy and wind effects on rainfall catch. The study was conducted at the Stephen F. Austin Experimental Forest, about 20 km SW of Nacogdoches, Texas. A recording anemometer was also installed at a height corresponding to the standard gage orifice. Based on data from 67 storms collected over a one-year period (July 1995-August 1996), all three conventional gages consistently caught less rainfall than the reference pit gage with an average percent deficiency greater than 10 percent. However, the recording gage caught 2.7 percent less and the shielded gage caught 1 percent more than the standard gage—differences less than those reported elsewhere. The deficiencies were highly correlated with storm intensity, duration, or total rainfall. When the correction for wind effect on angle of raindrop inclination is included, the percent catch deficiency of the standard gage was reduced from 11 percent to 6 percent. The remaining errors may be attributed to wind effects (streamline vs. turbulent flow), nonrandom errors, or other unknown sources.     

Location wise comparison of mixture distributions for assessment of wind power potential: A parametric study

Scientific literature discussed various types of mixture models and models derived from maximum entropy principle using short-term wind speed data for their relative assessment. The literature on suitability of these mixture models for long-term data is rarely available. However, for correct assessment of wind power potential both wind speed and wind direction are equally important. Therefore, in this paper, both wind speed and wind direction are simultaneously analyzed using several types of mixture distribution and compared the same with conventional Weibull distribution. For wind speed and wind power density assessment, the mixture distributions such as Weibull--Weibull distribution, Gamma--Weibull distribution, Truncated Normal--Weibull distribution, Truncated Normal--Normal distribution, proposed Truncated Normal--Gamma distribution and Gamma--Gamma distribution along with MEP-distribution are compared with conventional 2-parameter Weibull distribution. Similarly, for wind direction analysis, the finite mixtures of von-Mises distribution are compared with conventional von-Mises distribution. Judgment criteria include R², RMSE, Kolmogorov--Smirnov test and relative percentage error in wind power density. The sites selected are the three onshore locations of India, viz., Calcutta, Trivandrum, and Ahmedabad. The results show that for wind speed assessment, mixture distribution performs better than the conventional Weibull distribution for analyzing wind power density. However, location wise comparison of all mixture distribution is of prime importance. For wind direction analysis, finite mixture of two von-Mises distributions proved to be a suitable candidate for Indian climatology.     

A hybrid model based on smooth transition periodic autoregressive and Elman artificial neural network for wind speed forecasting of the Hebei region in China

Wind energy, one of the most promising renewable and clean energy sources, is becoming increasingly significant for sustainable energy development and environmental protection. Given the relationship between wind power and wind speed, precise prediction of wind speed for wind energy estimation and wind power generation is important. For proper and efficient evaluation of wind speed, a smooth transition periodic autoregressive (STPAR) model is developed to predict the six-hourly wind speeds. In addition, the Elman artificial neural network (EANN)-based error correction technique has also been integrated into the new STPAR model to improve model performance. To verify the developed approach, the six-hourly wind speed series during the period of 2000–2009 in the Hebei region of China is used for model construction and model testing. The proposed EANN-STPAR hybrid model has demonstrated its powerful forecasting capacity for wind speed series with complicated characteristics of linearity, seasonality and nonlinearity, which indicates that the proposed hybrid model is notably efficient and practical for wind speed forecasting, especially for the Hebei wind farms of China.     

Performance evaluation of a horizontal axis wind turbine in operation

The operation of modern horizontal axis wind turbine (HAWT) includes a number of important factors, such as wind power (P), power coefficient (C_P), axial flow induction factor (a), rotational speed (Ω), tip speed ratio (λ), and thrust force (T). The aerodynamic qualities of these aspects are evaluated and discussed in this study. For this aim, the measured data are obtained from the Sebenoba Wind Energy Power Plant (WEPP) that is located in the Sebenoba region in Hatay, Turkey, and a wind turbine with a capacity of 2 MW is selected for evaluation. According to the results obtained, the maximum turbine power output, maximum power coefficient, maximum axial flow induction factor, maximum thrust force, optimum rotational speed, probability density of optimum rotational speed, and optimum tip speed ratio are found to be 2 MW, 30%, 0.091, 140 kN, 16.11 rpm, 46.76%, and 7, respectively. This study has revealed that wind turbines must work under optimum conditions in order to extract as much energy as possible for approaching the ideal limit.     

Public acceptance of large-scale wind energy generation for export from Ireland to the UK: evidence from Ireland

Although international trade in energy may offer a flexible and cost effective means by which European countries could meet their renewable energy targets, developers in the exporting nation can face local opposition for reasons which are not always clear. Using focus groups and a public survey, we contrast perspectives between local stakeholders and wind farm operators and investigate the community impacts associated with large-scale wind energy for domestic use and export from Ireland to the UK. Although the export of renewable energy from Ireland to the UK is currently on hold, our findings suggest that significant investment is required by the state and wind farm operators in better information provision, trust building, effective instruments to internalise wind farm externalities and co-management arrangements before Ireland can fully capture the benefits of wind exports to the UK.     

A wind-solar PV hybrid power system with battery backup for water pumping in remote localities

After energy, water is the most critical commodity to be made available to people to keep them alive. Saudi Arabia has vast land and people are living in all regions. Most of these are connected to national grid but some are not, especially in remote areas like in the north, south, and west south. Pumping water in remote areas for domestic needs like agriculture and animals beside human needs is essential and require regular power supply. The present idea of wind-PV-Battery hybrid power system based on 100% renewable source is being proposed to utilize and tested in some of the regions on experimental bases. Of the five locations chosen for the purpose, namely Dhahran, Riyadh, Jeddah, Guriat and Nejran, some are good from both wind and solar intensity point of view some have good winds only and some good solar only. Nearly optimal size of PV-Wind water pumping system is determined for each of these sites considering the availability of solar and wind energy distributions throughout the year in these sites. It is shown that the monthly total water pumping capacity when using nearly optimal PV-Wind water pumping system is fairly uniform throughout the year except for the sites of Guriat and Riyadh. In these sites higher water pumping capacity is observed during the spring and summer months. On the other hand the cost of underground water pumping is found to vary between 6 to 12 US¢/m³ for the five sites considered.     

A Weibull and finite mixture of the von Mises distribution for wind analysis in Mersing,Malaysia

Studies of wind direction receive less attention than that of wind speed; however, wind direction affects daily activities such as shipping, the use of bridges, and construction. This research aims to study the effect of wind direction on generating wind power. A finite mixture model of the von Mises distribution and Weibull distribution are used in this paper to represent wind direction and wind speed data, respectively, for Mersing (Malaysia). The suitability of the distribution is examined by the R² determination coefficient. The energy analysis, that is, wind power density, only involves the wind speed, but the wind direction is vital in measuring the dominant direction of wind so that the sensor could optimize wind capture. The result reveals that the estimated wind power density is between 18.2 and 25 W/m², and SSW is the most common wind direction for this data.     

A novel blade design for Savonius wind turbine based on polynomial bezier curves for aerodynamic performance enhancement

ABSTRACT

Advanced wind turbine designs and technologies have been evolved to take advantage of wind energy. Despite the significant progress already attained, the need for a dependable wind energy converter particularly devoted to small-scale applications remains a challenging issue. Due to its design simplicity, Savonius wind turbine is the most suitable candidate for such applications. It operates at low wind speed, with the necessary starting capacity and insensitivity to wind directions. Moreover, in the literature related to wind energy, the Savonius rotor is known for its low performance compared to other types of wind turbines. In this paper, we present a study into the utilization of Bézier curves and transient computational fluid dynamics (CFD) to optimize the conventional Savonius blade design. The k-ω SST turbulence model is employed to perform a series of CFD simulations in order to assess the power coefficient of each generated design. A validation of optimization results using the Taguchi method was carried out. The comparative analysis of the torque and power coefficients shows a significant increase in the power coefficient (C_p). The optimal C_p is 0.35 and is 29% higher than the conventional Savoniu wind turbine (SWT). Subsequently, the effectiveness of the innovative geometry is proved by improved pressure and velocity distributions around blades of novel design.     

An Assessment of Spontaneous Vegetation Recovery in Aggregate Quarries in Coastal Sand Dunes in Buenos Aires Province,Argentina

Sand dune quarries are a location of common aggregate mining activity developed in coastal areas, especially in the southeast Buenos Aires province, Argentina. In this article, spontaneous plant development after extraction activity ceased was evaluated. Five areas (three quarried and two natural/conservation areas) were sampled for plant cover and composition as well as sediment characterization. Different indexes, principal component analysis, and cluster analyses were applied to compare the areas. The dominant families observed in four of the five areas were Asteraceae, Poaceae, and Cyperaceae, and most of the species are commonly found in sandy and humid soils and/or modified/anthropized ones. Percentages of plant cover increased with time because of the cessation of active aggregate extraction. Indexes and multivariate analyses showed that it was possible to distinguish quarried and natural areas based on composition and vegetation cover. The distribution of plant species among the four areas responded to the presence of mining activity, but it also responded to the topographical position and consequently the depth of the groundwater level. Besides these differences, the four areas shared many native species. The results might indicate that once the activity has ceased, quarried areas may spontaneously and quickly develop a plant community with some similarities to those present in the nonquarried areas. However, given that the extracting activity involves the removal of the soil, revegetation of this type of environment depends on the presence of natural areas in the surroundings, which can serve as a source of seeds and propagules for plant regeneration.     

Discourses of on-farm wind energy generation in the UK farming press

As the owners of the majority of land in the U.K., farmers are well placed to contribute to renewable energy targets. Media coverage can both drive and reflect farmers’ views about renewable energy but has been largely unexplored to date. This article uses discourse analysis to examine the evolution of coverage of one form of renewable energy – on-farm wind – in the U.K. farming press from 1980 to 2013. We identified a diverse debate with five major discourses. On-farm wind turbines are alternatively represented as: profitable farm diversification opportunities; producers of clean energy; important for rural development and sources of conflict. Although press coverage predominantly encourages wind energy production, a further discourse advises farmers to ‘Proceed with Caution’. While emphasising images and values which have widespread affinity among U.K. farmers, the press have increasingly employed an economic frame, constructing wind energy generation as a farm diversification strategy. The most recent farming press coverage predominantly encourages an instrumental approach to wind energy, crowding out other (non-economic) rationales and marginalising local community concerns. This appears to reflect the financial orientation of recent policy support (particularly Feed-in Tariffs), and may have long-term costs in enabling sustainable energy production systems.     

Investigation of sustainable energy alternatives for powering remote communities in northern Ontario

ABSTRACT

Remote communities in the North of Ontario survive in isolation as their proximity to the southern industrial sector of the province limits their accessibility to the major grid. The lack of grid connection has led to antiquated methods of power generation which pollute the environment and deplete the planet of its natural resources. Aside from the primary means of electricity generation being by diesel generators, generation infrastructure is deteriorating due to age and the stagnation of the power supply has led to communities facing load restrictions. These challenges may be resolved by introducing clean energy alternatives and providing a fuel blend option. The primary energy sources investigated in this research are solar, wind, and hydrogen. To assess the viability of these energy production methods in Northern communities, an exergy analysis is employed as it utilizes both the first and second law of thermodynamics to determine systems’ efficiency and performance in the surroundings. Local weather patterns were used to determine the viability of using wind turbines, solar panels and/or hydrogen fuel cells in a remote community. Through analysis of the resources available at the community, it was determined that the hydrogen fuel cell was best suited to provide clean energy to the community. Wind resulted in low efficiency in the range of 2–3% while solar efficiencies resulted in ranges of 18 – 19%, as the seasonal variations between the three years is not very great. Due to the higher operating efficiencies observed of the PV panels it would also be an attractive alternative to diesel generators however, the lack of consistent operation above 30% efficiency throughout the year, resulted in hydrogen fuel cells being a better alternative.     

Blade thickness effect on the aerodynamic performance of an asymmetric NACA six series blade vertical axis wind turbine in low wind speed

ABSTRACT

Vertical axis wind turbine (VAWT) is an economic and widely used energy converter for converting wind energy into useful form of energy, like mechanical and electrical energy. For efficient energy conversion in low wind speed and to have improved power coefficient of asymmetric blade VAWT, selection of optimum blade thickness is needed thus entailing its detailed investigation with respect to different operating wind speed conditions. Present study methodically explores the impact of thickness to chord (t/c) ratio on aerodynamic performance of a three bladed asymmetrical blade H-Darrieus VAWT at different low wind speed conditions by using 2D unsteady CFD simulations. The optimal t/c is obtained on the basis of maximum power coefficient and average moment coefficient of the turbine. The aerodynamic performance curves are obtained at different operating and t/c conditions and the performance insights are corroborated with the findings from the flow physics study to come to some concrete conclusions on the effects of the thickness to chord ratio. The present study identifies large blade curvature to create a large diverging passage on the blade suction surface as the prominent reason for aerodynamic performance drop at a high t/c ratio.     

Industrial impact on marsh soils at the Bahia Blanca Ria, Argentina

The Bahia Blanca Estuary is located in southern Buenos Aires province, Argentina. The area is linked to a petrochemical industrial complex, whose raw materials and final products contaminate the surrounding areas via atmospheric pollution and effluents, which are dumped in the estuary waters. To establish the effects of the industrial waste disposal on the nearest coastal soils, 17 samples were taken at different distances from the loading dock and the outfall pipes of the industrial complex. Later, the physicochemical characteristics of the soil samples, their hydrocarbon contents, sulfides, sulfates, Zn, Cu, and Pb were analyzed and a comparison was made to control samples, which were not affected by the industrial outfall. Hydrocarbons, Zn, Cu, and Pb contents were found at levels that modified the physical and chemical characteristics of the soils. The resistance to penetration shows that the thinner the film of water that surrounds the particles or aggregates, the smaller the migration of organic micelle, which settle on the surface of the contact material. This is demonstrated by the degree of cohesion reached by the particles and the strong influence on the index of hydrophobicity. The high porosity shows that the continuity of the porous space of the soil matrix is impeded by the presence of pollutants, which generate areas that are highly limiting to water flow. The oxidation-reduction potential and the low concentrations of soluble forms of Cu and Pb compared with their concentrations precipitated as sulfides confirm the action of the pollutants.     

风能资源开发利用的社会需要和发展前景

开发风能资源、利能风力发电在我国虽然只有数十年，但发展却很快。作为可再生的清洁能源越来越受到重视。不仅有巨大的环保意义，也有突出的经济效益。本文从风能利用的意义和社会需要展开论证，结合我国风能资源利用的概况，特别是结合风电装机最多的新疆的实际情况进行估算，从多侧面论述了风能资源的开发利用问题。     

Nonlinear control of a wind turbine based on nonlinear estimation techniques for maximum power extraction

This work proposes nonlinear estimators with nonlinear controllers, for variable speed wind turbine (VSWT) considering that either the wind speed measurement is not available or not accurate. The main objective of this work is to maximize the energy capture from the wind and minimizes the transient load on the drive train. Controllers are designed to adjust the generated torque for maximum power output. Estimation of effective wind speed is required to achieve the above objectives. In this work the estimation of effective wind speed is done by using the Modified Newton Rapshon (MNR), Neural Network (NN) trained by different training algorithms and nonlinear time series based estimation. Initially the control strategies applied was the classical ATF (Aerodynamic torque feed forward) and ISC (Indirect speed control), however due their weak performance and unmodeled WT disturbances, nonlinear static and dynamic feedback linearization techniques with the above wind speed estimators are proposed.