Molding Method, Thermal and Mechanical Properties of Jute/PLA Injection Molding

Natural composites have been important materials system due to preservation of earth environments. Natural fibers such as jute, hemp, bagasse and so on are very good candidate of natural composites as reinforcements. On the other hand regarding matrix parts thermosetting polymer and thermoplastic polymer deriver form petrochemical products are not environmental friendly material, even if thermoplastic polymer can be recycled. In order to create fully environmental friendly material (FEFM) biodegradable polymer which can be deriver from natural resources is needed. Therefore poly(lactic acid) (PLA) polymer is very good material for the FEFM. In this paper jute fiber filled PLA resin (jute/PLA) composites was fabricated by injection moldings and mechanical properties were measured. It is believable that industries will have much attention to FEFM, so that injection molding was adopted to fabricate the composites. Long fiber pellet fabricated by pultrusion technique was adopted to prepare jute/PLA pellet. Because it is able to fabricate composite pellets with relative long length fibers for injection molding process, where, jute yarns were continuously pulled and coated with PLA resin. Here two kinds of PLA materials were used including the one with mold releasing agent and the other without it. After pass through a heated die whereby PLA resin impregnates into the jute yarns and sufficient cooling, the impregnated jute yarns were cut into pellets. Then jute/PLA pellets were fed into injection machine to make dumbbell shape specimens. In current study, the effects of temperature of PLA melting temperature i.e. impregnation temperature and the kinds of PLA were focused to get optimum molding condition. The volume fractions of jute fiber in pellet were measured by several measuring method including image analyzing, density measurement and dissolution methods. Additionally, thermal and mechanical properties were investigated. It is found that 250° is much suitable for jute/PLA long fiber pultrusion process because of its less heat degradation of jute, better impregnation, acceptable mechanical property and higher production efficiency. Additionally the jute fibers seem much effective to increase deflection temperature under load, tensile modulus and Izod strength.     

Man-Made and Natural Fibres as a Reinforcement in Fully Biodegradable Polymer Composites: A Concise Study

Biodegradable and ecologically friendly polymer materials attract great attention of many scientific groups in the world as they fit well in the sustainable development policy and are considered to be “a right thing to do” by the general public. Such polymers can be modified by the addition of different fillers, favorably of natural origin. In the paper we provide a comparison between composites based on two biodegradable polymers: poly(lactic acid)—biodegradable, natural stock polymer and poly(butylene succinate)—biodegradable polymer produced from fossil based materials. For each polymer we have prepared a series of composites with different fibres (natural: hemp and flax, and manmade: Cordenka) and different filler loadings. To fully characterize obtained materials thermal, mechanical and surface free energy measurements were performed, completed with morphology observations and an attempt to compare the experimental data for tensile measurements with values obtained using the modified rule of mixtures. The tensile results calculated using the modified rule of mixture for below 30% fibre loading are found to be fitting the experimental data. Composites mechanical properties and morphology were strongly affected by the type of fibre used and its loading, however thermal properties remained almost unchanged. In specific, Cordenka fibres tend to form bunches which presence greatly influences the mechanical properties but still our studies have shown clear advantage of manmade Cordenka fibres over the hemp and flax fibres when considering distribution and fibre–polymer interaction.     

Cotton Fibre-reinforced Thermosets Versus Ramie Composites: A Comparative Study using Petrochemical- and Agro-based Resins

Natural fibres offer an interesting alternative to petrochemical products. Reclaimed cotton is mainly used as a low cost fibre to “fill” composites used as interior parts in the automotive industry. Mechanical requirements of such composites are low and the potential of the cotton-fibre to reinforce plastics is not used adequately. This paper gives background information and discusses the use of the cotton fibres in composites compared to ramie fibres. In this study the fibre strength was tested with a Dia-Stron device, fineness was tested with Fibreshape. A roller card is well suited to process fibres to a multi layer web. Cotton and ramie fibres were embedded in epoxy resin and a bio-based resin PTP^®. The composites were tested for impact and tensile properties. The results show that mechanical properties of the composites are strongly influenced by fibre properties. The data and results demonstrate the important role force-elongation characteristics of fibre play in optimising the properties of natural fibre composites. Cotton with its morphological and mechanical properties can play a more crucial role to optimise products with a view to improve the impact properties.     

Performance of Cow Dung Reinforced Biodegradable Poly(Lactic Acid) Biocomposites for Structural Applications

In this work, performance of cow dung (CD) reinforced poly(lactic acid) (PLA) biocomposites was investigated for the potential use in load bearing application. CD of average 4 mm size was blended with PLA at different CD ratios (0–50 wt%) and their effects on the biocomposite properties were studied. The results showed an improvement in the flexural properties, while the tensile and impact strength dropped by 20 and 28% with the addition of 50% CD. The decline in the tensile and impact strength was due to micro-cracking and voids formation at higher CD content. Also, the incorporation of CD slightly decreased the thermal stability of the biocomposite. However, dynamic mechanical properties of the biocomposites generally improved. SEM analysis of tensile and impact fractured surfaces indicated that the CD had a reasonable adhesion with matrix. Moreover, the SEM micrographs of soil burial studies showed an accelerated degradation of higher CD wt% biocomposites.     

Thermoplastic Starch (TPS)/Polylactic Acid (PLA) Blending Methodologies: A Review

Polylactic acid (PLA) and thermoplastic starch (TPS) are biodegradable polymers of biological origin, and the mixture of these polymers has been studied due to the desirable mechanical properties of PLA and the low processing cost of TPS. However, the TPS/PLA combination is thermodynamically immiscible due to the poor interfacial interaction between the hydrophilic starch granules and the hydrophobic PLA. To overcome these limitations, researchers studied the modification, processing, and properties of the mixtures as a strategy to increase the compatibility between phases. This review highlights recent developments, current results, and trends in the field of TPS/PLA-based compounds during the last two decades, with the main focus of improving the adhesion between the two components. The TPS/PLA blends were classified as plasticized, compatible, reinforced and with nanocomposites. This article presents, based on published research, TPS/PLA combinations, considering different methods with significant improvements in mechanical properties, with promising developments for applications in food packaging and biomedicine.

     

Compatibilization Improves Performance of Biodegradable Biopolymer Composites Without Affecting UV Weathering Characteristics

With growing interest in the use of eco-friendly composite materials, biodegradable polymers and composites from renewable resources are gaining popularity for use in commercial applications. However, the long-term performance of these composites and the effect of compatibilization on their weathering characteristics are unknown. In this study, five types of biodegradable biopolymer/wood fiber (WF) composites were compatibilized with maleic anhydride (MA), and the effect of accelerated UV weathering on their performance was evaluated against composites without MA and neat biopolymers. The composite samples were prepared with 30 wt% wood fiber and one of the five biodegradable biobased polymer: poly(lactic) acid (PLA), polyhydroxybutyrate (PHB), poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), Bioflex (PLA blend), or Solanyl (starch based). Neat and composite samples were UV weathered for 2000 h (hours), and characterized for morphological, physical, thermal, and mechanical properties before and after weathering. Compared to composites without MA, composites containing MA grafted polymers exhibited improved properties due to increased interfacial adhesion between the fiber and matrix. Upon accelerated weathering, thermal and mechanical properties of 70% of the samples substantially decreased. Surfaces of all the samples were roughened, and drastic color changes were observed. Water absorption of all the samples increased after weathering exposure. Even though the compatibilization is shown to improve composite properties before weathering, it did not affect weathering of samples, as there were no considerable differences in properties exhibited by the composites with MA and without MA after weathering. The results suggest that compatibilization improves properties of biodegradable biobased composites without affecting its UV degradation properties.     

Enhanced Interfacial Adhesion and Characterisation of Recycled Natural Fibre-Filled Biodegradable Green Composites

The structural, thermal, mechanical, and biodegradable properties of composite materials made from polylactide (PLA) and agricultural residues (arrowroot (Maranta arundinacea) fibre, AF) were evaluated. Melt blended glycidyl methacrylate-grafted polylactide (PLA-g-GMA) and coupling agent-treated arrowroot fibre (TAF) formed the PLA-g-GMA/TAF composite, which had better properties than the PLA/AF composite. The water resistance of the PLA-g-GMA/TAF composite was greater than that of the PLA/AF composite; the release of PLA in water from the PLA/AF and PLA-g-GMA/TAF composites indicated good biological activity. The PLA-g-GMA/TAF material had better mechanical properties than PLA/AF. This behaviour was attributed to better compatibility between the grafted polymer and TAF. The results indicated that the T_g of PLA was increased by the addition of fibre, which may have improved the heat resistance of PLA. Furthermore, the mass losses following burial in soil compost indicated that both materials were biodegradable, especially at high levels of AF or TAF substitution.     

Sustainable Bio-Composites from Renewable Resources: Opportunities and Challenges in the Green Materials World

Sustainability, industrial ecology, eco-efficiency, and green chemistry are guiding the development of the next generation of materials, products, and processes. Biodegradable plastics and bio-based polymer products based on annually renewable agricultural and biomass feedstock can form the basis for a portfolio of sustainable, eco-efficient products that can compete and capture markets currently dominated by products based exclusively on petroleum feedstock. Natural/Biofiber composites (Bio-Composites) are emerging as a viable alternative to glass fiber reinforced composites especially in automotive and building product applications. The combination of biofibers such as kenaf, hemp, flax, jute, henequen, pineapple leaf fiber, and sisal with polymer matrices from both nonrenewable and renewable resources to produce composite materials that are competitive with synthetic composites requires special attention, i.e., biofiber–matrix interface and novel processing. Natural fiber–reinforced polypropylene composites have attained commercial attraction in automotive industries. Natural fiber—polypropylene or natural fiber—polyester composites are not sufficiently eco-friendly because of the petroleum-based source and the nonbiodegradable nature of the polymer matrix. Using natural fibers with polymers based on renewable resources will allow many environmental issues to be solved. By embedding biofibers with renewable resource–based biopolymers such as cellulosic plastics; polylactides; starch plastics; polyhydroxyalkanoates (bacterial polyesters); and soy-based plastics, the so-called green bio-composites are continuously being developed.     

A Comparative Study of Doum fiber and Shrimp Chitin Based Reinforced Low Density Polyethylene Biocomposites

The aim of this paper was to study the effects of reinforcing low density polyethylene (LDPE) by using bio-fillers (Doum cellulose or Shrimp chitin) on the mechanical properties. Both, Doum cellulose extracted frsom Doum leaves and Shrimp chitin extracted from shrimp co-products were compounded with LPDE without and with compatibilizer. The biocomposites were prepared by melt blending in a twin-screw extruder. Torsion and flexural tests were performed to investigate the impact of each reinforcement on the biocomposite mechanical properties. The SEM was carried out to study the filler/polymer interface adhesion. The present study has demonstrated that Doum fibers and shrimp chitin succeed in improving the mechanical properties of LPDE bio-composites. The results also showed that the use of maleic anhydride-grafted polyethylene as a compatibilizer improves filler adhesion/matrix and mechanical properties. This study exhibits that polyethylene composites based on Doum fibers or shrimp chitin can be used to replace the polyethylene materials in several fields like packaging and automotive industries.     

Natural Rubber-Based Pressure-Sensitive Adhesives: A Review

The purpose of this review is to describe the various aspects of pressure-sensitive adhesives prepared from natural rubber. Pressure-sensitive adhesives (PSAs) adhere instantaneously to a variety of surfaces upon application of slight pressure and can be obtained using different technologies. PSAs are materials that develop tack for low pressures and short contact times. There are number of factors affecting the adhesion property of natural rubber based pressure-sensitive adhesives. In this review, factors affecting adhesion property such as tack, peel and shear are examined in light of their relevance to adhesion in addition to measurement methods of each of the three major adhesion properties. This review paper covers the work being carried out from the last 20 years in the field of natural rubber based pressure sensitive adhesives.     

Investigation on the Influence of EVA Content on the Mechanical and Thermal Characteristics of Poly(lactic acid) Blends

Poly(lactic acid) (PLA) has gained considerable attention nowadays as a biocompatible polymer owing to its advantage of being prepared from renewable resources. PLA exhibits excellent tensile strength, fabricability, thermal plasticity and biocompatibility properties comparable to many petroleum based plastics. However, low heat distortion temperature, brittleness and slow crystallization rate limit the practical applications of PLA. In order to address these limitations, an attempt has been made in the current work to prepare binary blends of PLA with ethylene vinyl acetate (EVA) at different compositions via melt mixing technique. Systematic investigation on the mechanical properties, thermal degradation and crystallization behavior for PLA-EVA blends was carried out. The impact strength of binary blends of PLA–EVA was found to increase significantly by 176% for 15 wt% of EVA compared to virgin PLA. This is due to the strong interfacial adhesion among PLA and EVA resulting in brittle to ductile transition. Scanning electron microscopy analysis for impact fractured surfaces of binary blends of PLA implied the toughening effect of PLA by EVA. Thermogravimetry analysis results revealed that the activation energy of PLA–EVA blends decreased with increase in EVA content in the PLA matrix. While, differential scanning calorimetry results obtained for PLA–EVA blends revealed the improvement in crystallinity when compared with neat PLA. The effect of EVA on non-isothermal melt crystallization kinetics of PLA was also examined via DSC at various heating rates. Decreasing trend in the t_1/2 values indicated the faster rate of crystallization mechanism after addition of EVA in the PLA matrix.     

Single-Plant Biocomposite from Ricinus Communis: Preparation, Properties and Environmental Performance

A single-plant biobased composite material was prepared from fibre and matrix constituents produced from the castor plant, ricinus communis. It is shown that the mechanical properties of the castor plant fibres are comparable to those of other bast fibres and that the stiffness and strength characteristics of the castor fibre/polyamide 11 biocomposite compare well with those of other natural fibre composites. By using a biobased thermoplastic matrix material the reliance on non-renewable feedstock sources is reduced and end-of-lifetime recyclability is improved. The analysis of the environmental performance of the new castor plant composite suggests that the biobased material has great potential as a sustainable alternative replacing glass fibre-reinforced plastics.     

Soil Biodegradation of PHBV/Peach Palm Particles Biocomposites

There is great interest in developing eco-friendly green biocomposites from plant-derived natural fibers and crop-derived bioplastics attributable to their renewable resource-based origin and biodegradable nature. Fully biodegradable composites, made from both biodegradable polymeric matrices and natural fibers, should be advantageous in some applications, such as one way packaging. Polyhydroxyalkanoates (PHAs) are naturally occurring biodegradable polymers produced from a wide range of microorganisms, with poly(3-hydroxybutyrate) P(3HB) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) being important examples of PHAs. In this work, biocomposites of PHBV consisting of a PHBV matrix incorporating peach palm particles (PPp), [i.e., 100/0, 90/10, 80/20 and 75/25 (%w/w) PHBV/PPp] were processed by injection molding at 160 °C. The effect of PPp loading on the thermal and the mechanical properties, as well as on the morphological behavior of the PHBV/PPp biocomposites was investigated. Soil biodegradation tests were carried out by burying specimen beakers containing aged soil and kept under controlled temperature and humidity in accordance with ASTM G160-98. Degradation of the biocomposites was evaluated by visual analysis, scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) following test exposures of up to 5 months. The addition of PPp reduced the maximum strength and the elongation at break of the biocomposites. On the other hand, the Young’s modulus improved with the PPp content. Micrographs of the fracture surfaces following tensile strength testing revealed a large distance between the PHBV matrix and PPp particles although a low interaction is expected. Where measured, these distances tended increase as the PPp content of the biocomposites increased. Soil biodegradation tests indicated that the biocomposites degraded faster than the neat polymer due to the presence of cavities that resulted from introduction of the PPp and that degradation increased with increasing PPp content. These voids allowed for enhanced water adsorption and greater internal access to the soil-borne degrader microorganisms.     

End-Of-Life Textiles as Reinforcements in Biocomposites

A number of attempts have been made to recycle cotton/polyester blend woven fabrics after use; however, most of these fabrics are disposed of in landfills. Major part of these blend fabrics are not recycled due to complexity of the fibre arrangement and cannot be separated economically. This study shows that these discarded woven fabrics could be directly used as reinforcements in composites without fibre separation. Uniform alignment in the woven fabric provided consistent properties to the composites. The fabrics were reinforced by soybean-based-bioresins to produce biocomposites. The composites were analysed for mechanical, thermal, viscoelastic and morphological properties. Porosity and wettability of the composites were also evaluated. Results demonstrate that the tensile strength and modulus of over 100 and 10 MPa, respectively, can be obtained without any fibre treatment. Furthermore, impact strength over 70 kJ/m² was obtained without any chemical treatment on fibres. The porosity of the composites produced was less than 9 vol%. Additionally, the fabrics were treated with alkali in order to improve the fibre–matrix interface and the composite properties were studied. From the economical perspective, these composites can be produced at a low cost as the major component is available for free or low cost.     

Tensile,Flexural and Chemical Resistance Properties of Sisal Fibre Reinforced Polymer Composites: Effect of Fibre Surface Treatment

In this study, effect of fibre surface treatment on tensile, flexural and chemical resistance properties were studied for sisal fibre reinforced composites. Natural ligno cellulosic sisal fibre reinforced composites were prepared by different surface treatments by hand lay-up method. Fibre surface treatments were carried out to produce good interface between the fibre and the matrix to improve the mechanical properties. Fibre surface treatments were done by boiled the sisal fibres in different % of NaOH and treated the fibres in different % of NaOH, treated in acetic acid and methanol. Unsaturated polyester resin was used as the matrix for preparing the composites. For comparison, these properties for untreated sisal fibre reinforced composites were also studied. From the results it was observed that 18% aqueous NaOH boiled sisal fibre reinforced composites have higher tensile, flexural properties than other composites. Untreated sisal fibre composites show lower properties than treated composites. Chemical resistance properties indicate that all sisal fibre reinforced composites are resistance to all chemicals except carbon tetra chloride. The tests are carried out as per the ASTM standards.     

Characterization of Biodegradable Polymer Blends of Acetylated and Hydroxypropylated Sago Starch and Natural Rubber

Development of biodegradable polymers from absolute environmental friendly materials has attracted increasing research interest due to public awareness of waste disposal problems caused by low degradable conventional plastics. In this study, the potential of incorporating natural rubber latex (NRL) into chemically modified sago starch for the making biodegradable polymer blends was assessed. Native sago starch was acetylated and hydroxypropylated before gelatinization in preparing starch thermoplastic using glycerol. They were than casted with NRL into biopolymer films according to the ratios of 100.00/0.00, 99.75/1.25, 98.50/2.50, 95.00/5.00, 90.00/10.00 and 80.00/20.00 wt/wt, via solution spreading technique. Water absorption, thermal, mechanical, morphological and biodegradable properties of the product films were evaluated by differential scanning calorimetry (DSC), universal testing machine (UTM), scanning electron microscopy (SEM) and fourier transform infrared spectroscopy. Results showed that acetylation promoted the incorporating behavior of NRL in sago starch by demonstrating a good adhesion characteristic and giving a uniform, homogenous micro-structured surface under SEM observation. However, the thin biopolymer films did not exhibit any remarkable trend in their DSC thermal profile and UTM mechanical properties. The occurrence of NRL suppressed water adsorption capacity and delayed the biodegradability of the biopolymer films in the natural environment. Despite the depletion in water adsorption capacity, all of the product films degraded 50 % within 12 weeks. This study concluded that biopolymers with desirable properties could be formulated by choosing an appropriate casting ratio of the sago starch to NRL with suitable chemical substitution modes.     

Processing Stability and Biodegradation of Polylactic Acid (PLA) Composites Reinforced with Cotton Linters or Maple Hardwood Fibres

Polylactic acid (PLA) composites comprising up to 25 wt% cotton linter (CL) or up to 50 % maple wood fibre (WF) were prepared by compounding and injection moulding. A reduction of crystallinity in the PLA matrix was observed as a result of the thermal processing method. These PLACL and PLAWF composites provided excellent improvements in both stiffness (with increases in tensile and flexural modulus) and toughness (increases in notched impact strength) properties over the neat PLA resin, while the tensile and flexural strengths of the composites were generally unchanged, while the strain at break values were reduced in comparison to the neat PLA. DMA results indicated incorporating these fibres caused the mechanical loss factor (tan δ) to decrease, suggesting better damping capabilities were achieved with the composites. SEM analysis of the impact fractured surfaces of the PLACL composites showed debonding-cavitation at the matrix-fibre interface while the PLAWF composites showed good wetting along its matrix-fibre interface. The composting of these composites up to 90 days showed that the degradation onset time was increased when increasing the fibre loadings, but the maximum degree of degradation and the maximum daily rates of degradation were decreased compared to neat PLA. On a weight basis of fibre loading, the PLACL composites had a quicker onset of biodegradation, a higher maximum daily rate of biodegradation and, overall, a higher degree of biodegradation at 90 days than the PLAWF composites, possibly due to the quicker thermal hydrolysis observed in the PLA matrix of the PLACL composites during processing and composting.     

Injection Molded Biocomposites from Soy Protein Based Bioplastic and Short Industrial Hemp Fiber

Biocomposites from soy based bioplastic and chopped industrial hemp fiber were fabricated using twin-screw extrusion and injection molding process. Soy based bioplastics were prepared through cooking with plasticizer and blending with biodegradable poly(ester amide). Mechanical, thermal properties and fracture surface morphology of the “green”/biocomposites were evaluated with universal testing system (UTS), dynamic mechanical analysis (DMA), Environmental Scanning Electron Microscopy (ESEM). It was found that the tensile strength and modulus, flexural strength and modulus, impact strength and heat deflection temperature of industrial hemp fiber reinforced biocomposites significantly improved. The fracture surfaces showed no signs of matrix on the fiber surface suggesting poor interfacial adhesion.     

Polylactic Acid Composites Utilising Sequential Surface Treatments of Lignocellulose: Chemistry,Morphology and Properties

Polylactic acid (PLA)—maple fibre composites have been synthesised using a series of sequentially modified cellulose fibres (namely alkylation followed by either acetylation or silanation). Confirmations of the sequential modifications were made using Fourier Transform Infrared Spectroscopy and Inductively Coupled Plasma—Atomic Emission Spectroscopy and the new surface morphologies analysed using Scanning Electron Microscopy. The key advantage of the use of sequential treatments (with initial alkali treatment) was the allowance for direct grafting of suitable chemical groups onto the cellulose in the fibre due to the removal of lignin, hemicellulose and other surface impurities. However, a balance was found to exist between alkali exposure time, concentration and resulting fibre integrity. The conditions used resulted in a loss in fibre weight, fibre moisture content and tensile strength. Sequential treatments with acetylation or silane resulted in a 15–21% strength recovery from that of the alkali treated composite. Factors that influenced this recovery in strength were the improved fibre-polymer interface, namely the hydrophilic balancing of the fibres and this further affected the thermal-hydrolysis of the PLA during composite fabrication.     

Comparison of Polylactic Acid/Kenaf and Polylactic Acid/Rise Husk Composites: The Influence of the Natural Fibers on the Mechanical, Thermal and Biodegradability Properties

This paper investigates and compares the performances of polylactic acid (PLA)/kenaf (PLA-K) and PLA/rice husk (PLA-RH) composites in terms of biodegradability, mechanical and thermal properties. Composites with natural fiber weight content of 20% with fiber sizes of less than 100 μm were produced for testing and characterization. A twin-screw extrusion was used to compound PLA and natural fibers, and extruded composites were injection molded to test samples. Flexural and Izod impact test, TGA, soil burial test and SEM were used to investigate properties. All results were compared to a pure PLA matrix sample. The flexural modulus of the PLA increased with the addition of natural fibers, while the flexural strength decreased. The highest impact strength (34 J m⁻¹), flexural modulus (4.5 GPa) and flexural strength (90 MPa) were obtained for the composite made of PLA/kenaf (PLA-K), which means kenaf natural fibers are potential to be used as an alternative filler to enhance mechanical properties. On the other hand PLA-RH composite exhibits lower mechanical properties. The impact strength of PLA has decreased when filled with natural fibers; this decrease is more pronounced in the PLA-RH composite. In terms of thermal stability it has been found that the addition of natural fibers decreased the thermal stability of virgin PLA and the decrement was more prominent in the PLA-RH composite. Biodegradability of the composites slightly increased and reached 1.2 and 0.8% for PLA-K and PLA-RH respectively for a period of 90 days. SEM micrographs showed poor interfacial between the polymer matrix and natural fibers.