水体表面微层中酞酸酯的光降解研究

研究了水体表面微层中酞酸酯化合物光降解的动力学,指出光催化降解符合一级动力学过程,实验证明：催化剂ＴｉＯ２为２ｇ．ｌ＾－１,ｐＨ为６,并有Ｈ２Ｏ２存在时,是ＤＢＰ,ＤＥＨＰ光降解的最佳条件,溶解氧增加有利于光降解,实际表面微层水样的光催化降解速率比模拟水样快。     

均匀沉淀法制备纳米TiO2及其在环保方面的应用

本文以偏钛酸为原料,采用均匀沉淀法制备纳米ＴｉＯ２,所制得的纳米微晶平均粒径约为８．５ｎｍ,并能在７００℃保持锐钛矿型晶体结构,当它应用于染料溶液的光催化分解,与ＭＴ－１５０Ｗ光催化相比,具有较好的催化活性。同时,我们用Ａｌ２Ｏ３陶瓷膜回怍纳米ＴｉＯ２循环再利用,这为纳米ＴｉＯ２在环保方面的大规模应用创造了条件。     

氟里昂12（CC12F2）燃烧分解催化剂性能的研究

本文对贵金属、氧化物和复合氧化物体系催化剂上氟里昂１２（Ｆ１２）燃烧分解反应进行了活性谰价和稳定性研究。结果表明：ＴｉＯ２，ＺｒＯ２／ＴｉＯ２催化剂对氟里昂１２燃烧分解反应具有良好的低温催化活性和较好的稳定性，ＺｒＯ２／ＴｉＯ２催化剂具有一定的臭氧－催化氧化活性。     

多氯代二恶英在土壤表面的紫外光解研究

本文利用５００Ｗ中压汞灯研究了二恶英在干燥土壤中的紫外光解，根据光解结果计算了土壤中二恶英的降解深度，并分析了五氯代二恶英（ＰｅＣＤＤ）的光解产物，结果表明，二恶英在土表面发生了较快的光解反应，反应在２ｈ内基本完成，降解深度为０．０２７ｍｍ，对ＰｅＣＣＤ光解产物的分析结果显示，二恶英在土壤表面紫外光降解的主要途径为脱氯，而且脱氯优先发生在邻位下。     

纳米TiO2光催化降解水溶性染料溶液的研究

研究了纳米ＴｉＯ２光催化剂对活性黄Ｘ６Ｇ,活性红Ｘ３Ｂ,活性蓝ＸＢＲ,碱性绿,碱性紫５ＢＮ,碱性品红等６种染料溶液的光解脱色效果。结果表明,在ｐＨ２的酸性溶液中,对浓度为６０ｍｇ／Ｌ的６种染料溶液的脱色率均超过９３．３％;即使对浓度达２００ｍｇ／Ｌ的活性蓝溶液,其脱色率仍可达７８．８％。染料溶液的ｐＨ值对纳米ＴｉＯ２光催化脱色效果影响较大。     

用SOS/umu测试评价光电催化降解五氯酚过程的遗传毒性特征

采用SOS/umu测试研究了五氯酚水溶液在光电催化反应过程中的遗传毒性变化及降解产物对鼠伤寒沙门氏菌TA1535/pSK1002的细胞毒性,并与五氯酚在直接光解、光催化反应过程中的降解产物进行了比较.五氯酚光电催化降解过程中降解产物对测试菌种的细胞毒性逐渐降低,产物经代谢活化的细胞毒性低于直接光解、光催化降解五氯酚的产物.五氯酚经光电催化降解15￣45分钟的产物经代谢活化测试结果呈阳性,在60￣120分钟的降解产物呈阴性,说明五氯酚的光电催化降解过程中生成了间接遗传毒性物质,但该类物质能够在光电催化过程中被去除.而五氯酚经直接光解、光催化处理120分钟的产物均具有遗传毒性风险.本研究结果表明光电催化技术的环境安全性优于直接光解、光催化技术.此外,SOS/umu测试作为一种简单、灵敏的遗传毒性物质检测方法,适合于评价光电催化技术的遗传毒性特征,可以作为评价该技术环境安全性的生态毒理学方法之一.     

纳米TiO_2光催化降解水溶性染料溶液的研究

研究了纳米ＴｉＯ２光催化剂对活性黄Ｘ６Ｇ、活性红Ｘ３Ｂ、活性蓝ＸＢＲ、碱性绿、碱性紫５ＢＮ、碱性品红等６种染料溶液的光解脱色效果。结果表明，在ｐＨ２的酸性溶液中，对浓度为６０ｍｇ／Ｌ的６种染料溶液的脱色率均超过９３．３％；即使对浓度达２００ｍｇ／Ｌ的活性蓝溶液，其脱色率仍可达７８．８％。染料溶液的ｐＨ值对纳米ＴｉＯ２光催化脱色效果影响较大     

有机磷农药敏作用的初步研究

本文研究了有机磷农药甲基１６０５和毒死蜱对＾１Ｏ２探针性物质二乙基二硫醚，萜品烯及ＲＯＯ和ＲＯ探针性物质２，６－二叔丁基－４－甲基苯酚和１，２，３，４－四氢萘光降解的敏化作用。结果表明基态氧直接参与了ＤＥＳ和α－ｔｅｒｐ的光解；在甲基１６０５的作用下，１／Ｋｅｘｐｔｌ与「αｔｅｒｐ」的关系表明，α－ｔｅｒｐ的降解不为＾１Ｏ２历程。     

二氧化钛催化下的氯化二苯并—对—二恶英光解反应

本文利用中压汞灯作光源，研究了氯化二苯并－对－二恶英（ＣＤＤａ，包括ＣＤＤ，ＤＣＤＤ〈ＰｅＣＤＤ和ＯＣＤＤ）在二氧化钛催化下的光解反应，并讨论了二氧化钛浓度、ＰＨ值、反应温度以及取代氯原子数目等对反应速率的影响，结果表明，二氧化钛能有效地催化ＣＤＤａ的光降解，在室温下，４ｈ内ＤＣＤＤ，ＰｅＣＤＤ，ＯＣＤＤ分解降解了８７．２％，８４．６％，９１．２％，反应温度和二氧化钛浓度是控制该反应的主要因素。     

混合菌群对偶氮染料的脱色降解研究进展

偶氮染料废水的排放会对水生环境及人类健康造成严重威胁.目前生物法处理偶氮染料的应用与研究居于首位,而混合菌群因具有多种微生物间的协同作用成为当前研究的热点.综述混合菌群的构建及偶氮染料脱色降解的影响因素,并重点阐述偶氮染料降解机理及降解酶系的相关研究.研究发现,混合菌群较单一菌株具有较好的脱色降解性能;其中碳氮源、温度、pH值、染料结构与浓度、溶氧量等因素对降解染料具有重要影响.细菌复合菌群是通过分泌一系列的酶如偶氮还原酶等使其偶氮双键断裂,产生的芳香胺类物质进一步被氧化成CO2和H2O,揭示了偶氮还原酶降解偶氮染料时的两种可能机制,即有无依赖氧化还原介质的偶氮染料降解.真菌复合菌群是通过生化反应来催化偶氮染料降解,阐述了漆酶降解染料的机理,即底物自由基中间体的产生和氧气还原成水.细菌与真菌复合菌群则是通过降解酶系统与生化反应相结合来降解染料.最后提出单一菌株存在着降解不彻底、效果不理想等问题,指出未来应根据废水中偶氮染料的种类、结构特点构建具有特异性、高效性且降解多种偶氮染料的混合菌群,并开展其生物降解的分子机制研究,进而为微生物降解偶氮染料的研发提供参考与理论支撑.(图2表3参96)     

UV-LED/P25-based photocatalysis for effective degradation of isothiazolone biocide

• UV-LED with shorter wavelength was beneficial for photocatalytic degradation. • SRNOM dramatically inhibit the degradation. • ·OH acts as the active radical in photocatalytic degradation. • Degradation mainly undergoes oxidation, hydrolysis and chain growth reactions. In this work, LED-based photocatalysis using mixed rutile and anatase phase TiO₂ (P25) as the photocatalyst could effectively remove 5-chloro-2-methyl-4-isothiazolin-3-one (CMIT) and methylisothiazolone (MIT) simultaneously, with removal efficiencies above 80% within 20 min. The photocatalytic degradation of both CMIT and MIT could be modeled using a pseudo-first-order rate equation. The photocatalytic degradation rates of CMIT and MIT under LED280 illumination were higher than under LED310 or LED360 illumination. At concentrations below 100 mg/L, the degradation rate of CMIT and MIT under LED illumination significantly increased with increasing catalyst dosage. Additionally, the effects of the chloride ion concentration, alkalinity and dissolved organic matter on the photocatalytic degradation reaction were also investigated. The ·OH free radicals were determined to play the primary role in the photocatalytic degradation reaction, with a degradation contribution of >95%. The photocatalytic degradation of CMIT and MIT mainly occurred via oxidation, hydrolysis, and chain growth reactions. Finally, the possible photocatalytic degradation pathways of CMIT and MIT over LED/P25 are proposed.     

几种环境激素酞酸酯的光催化降解研究

在紫外光照射下,以TiO2为催化剂,研究邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二环己酯(DCHP)和邻苯二甲酸丁基苄基酯(BBP)水溶液的光催化降解规律,不同结构特征的酞酸酯在降解过程中pH值均表现为先升高,再降低的趋势.降解为表观一级反应.采用色质联用技术(GC-MS)分别对上述物质降解过程中生成的中间体进行分析,提出了可能的降解机理.     

不同活性物种对光催化降解水中邻苯二甲酸二甲酯动力学的贡献研究

采用光催化氧化技术对邻苯二甲酸二甲酯（DMP）进行降解研究,并在基础上考察了催化剂量,溶液pH和溶液初始浓度对降解速率的影响。且采用Langmuir-Hinshelwood动力学模型来描述DMP的光催化降解,研究表明DMP的光催化降解符合假一级动力学。系统研究了光催化降解DMP过程中不同活性物种对光催化反应速率的贡献,实验结果表明：在TiO2光催化降解DMP的过程中,？OH为主要的活性物种,其对DMP的降解速率贡献高于94%,而其它活性物种（ecb-,hvb＋,O2？-和H2O2）对光催化贡献较小。     

TiO2/活性炭复合体对罗丹明B的光催化降解

以紫外灯为光源,通过对可溶性染料罗丹明B的降解反应,考察TiO2／活性炭复合体的光催化活性,探讨了光催化反应中溶液的pH值、光强、反应温度和罗丹明B的起始浓度对催化反应的影响,结果表明,TiO2／活性炭复合体具有很高的光催化活性,对罗丹明B的降解过程遵循Langmuir-Hinshelwood动力学方程,降解速率受pH值、罗丹明B起始浓度和入射光强度的影响很大,反应温度对降解速率影响很小．在研究范围内,pH6和40W的入射光强度有利于光催化降解．     

Solar photocatalytic decomposition of two azo dyes on multi-walled carbon nanotubes (MWCNTs)/TiO<Subscript>2</Subscript> composites

Multi-walled carbon nanotubes (MWCNTs)/TiO₂ composite photocatalysts with high photoactivity were prepared by sol-gel process and further characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), and UV-vis absorption spectra. Compared to pure TiO₂, the combination of MWCNTs with titania could cause a significant absorption shift toward the visible region. The photocatalytic performances of the MWCNTs/TiO₂ composite catalysts were evaluated for the decomposition of Reactive light yellow K-6G (K-6G) and Mordant black 7 (MB 7) azo dyes solution under solar light irradiation. The results showed that the addition of MWCNTs enhanced the adsorption and photocatalytic activity of TiO₂ for the degradation of azo dyes K-6G and MB 7. The effect of MWCNTs content, catalyst dosage, pH, and initial dye concentration were examined as operational parameters. The kinetics of photocatalytic degradation of two dyes was found to follow a pseudo-first-order rate law. The photocatalyst was used for seven cycles with photocatalytic degradation efficiency still higher than 98%. A plausible mechanism is also proposed and discussed on the basis of experimental results.     

Investigation of the effects of humic acid and H 2 O 2 on the photocatalytic degradation of atrazine assisted by microwave

A solution of atrazine in a TiO₂ suspension, an endocrine disruptor in natural water, was tentatively treated by microwave-assisted photocatalytic technique. The effects of mannitol, oxygen, humic acid, and hydrogen dioxide on the photodegradation rate were explored. The results could be deduced as follows: the photocatalytic degradation of atrazine fits the pseudo-first-order kinetic well with k = 0.0328 s⁻¹, and ·OH was identified as the dominant reactant. Photodegradation of atrazine was hindered in the presence of humic acid, and the retardation effect increased as the concentration of humic acid increased. H₂O₂ displayed a significant negative influence on atrazine photocatalysis efficiency. Based on intermediates identified with gas chromatography-mass spectrometry (GC-MS) and Liquid chromatography-mass spectrometry (LC-MS/MS) techniques, the main degradation routes of atrazine are proposed.     

Investigation of the effects of humic acid and H<Subscript>2</Subscript>O<Subscript>2</Subscript> on the photocatalytic degradation of atrazine assisted by microwave

A solution of atrazine in a TiO₂ suspension, an endocrine disruptor in natural water, was tentatively treated by microwave-assisted photocatalytic technique. The effects of mannitol, oxygen, humic acid, and hydrogen dioxide on the photodegradation rate were explored. The results could be deduced as follows: the photocatalytic degradation of atrazine fits the pseudo-first-order kinetic well with k = 0.0328 s^?1, and ·OH was identified as the dominant reactant. Photodegradation of atrazine was hindered in the presence of humic acid, and the retardation effect increased as the concentration of humic acid increased. H₂O₂ displayed a significant negative influence on atrazine photocatalysis efficiency. Based on intermediates identified with gas chromatography-mass spectrometry (GC-MS) and Liquid chromatography-mass spectrometry (LC-MS/MS) techniques, the main degradation routes of atrazine are proposed.     

Photocatalytic degradation of aqueous methyl-tert-butyl-ether (MTBE) in a supported-catalyst reactor

Contamination of groundwater by methyl-tert-butyl ether (MTBE) poses increasing problems to water companies. Here we demonstrate the feasibility of using a cylindrical, supported-catalyst reactor for photocatalytic degradation of MTBE in water. It was shown that photocatalytic degradation of MTBE follows pseudo first-order kinetics. The maximum reaction rate constant observed was 0.47 hr^–1. The reaction rate increases linearly with increasing light intensity. It was also found that the reaction rate is linearly proportional to the ratio of catalyst surface area to volume of reactor. Complete degradation of MTBE was reached with an excess supply of oxygen.     

TiO2/粉煤灰的制备及光催化性能研究

以钛酸丁酯为原料,以粉煤灰微珠为载体,采用溶胶-凝胶法制备了TiO2/粉煤灰光催化剂.负载于粉煤灰表面的TiO2平均粒径约为7nm,晶型为锐钛矿型,该催化剂在太阳光下降解初始浓度为10mg·l-1的甲基橙,经6h,甲基橙的降解率可达98.9%,将其应用于实际样品的测定,经3h降解率可达96.1%,显示出优越的光催化降解性能.     

Polyoxometalates for photocatalytic degradation of aqueous dyestuff solutions and quantitative structure–property relationship study on photolysis rate constants

Polyoxometalate, K₆TiW₁₁O₃₉Sn·7H₂O (TiW₁₁Sn), was synthesized and characterized. TiW₁₁Sn and K₆ZrW₁₁O₃₉Sn·12H₂O (ZrW₁₁Sn) were evaluated for their photocatalytic degradation of triarylmethane (brilliant green and acid blue 9), bisazo (C.I. reactive black 5), and monoazo dyestuffs (C.I. reactive red 24, C.I. reactive red 194, and C.I. reactive orange 5) with natural sunlight in homogeneous aqueous solutions. TiW₁₁Sn and ZrW₁₁Sn effectively and photocatalytically decolorized the dyestuffs. The TiW₁₁Sn- and ZrW₁₁Sn-mediated photocatalytic degradation of the dyestuffs involved a pseudo-first-order reaction and was modeled by Langmuir–Hinshelwood-type kinetics. The observed pseudo-first-order rate constants (K^/) of triarylmethane dyestuffs were generally bigger than that of the azo dyestuffs. Quantitative structure–property relationship models of the K^/ of the dyestuffs were developed using partial least-square regression. The cumulative variance of the dependent variable explained by the partial least-square components was > 0.753 for each optimal model. This value indicated that the model had good predictive ability and robustness. The K^/ values of the dyestuffs were related to the energy of the lowest unoccupied molecular orbital, and the most positive net atomic charges on a sulfur atom of dyestuffs. The linear correlation coefficients between the predicted and experimental values were all > 0.9950.