Soil column experiments used as a means to assess transport,sorption, and biodegradation of pesticides in groundwater

Soil column experiments are used to investigate the fate of three pesticides of high, intermediate, and low solubility in groundwater: N- phosphonomethyl glycine (glyphosate); O,O-diethyl-S-[(ethylthio)methyl]phosphorodithioate (phorate); (2,4-dichlorophenoxy)acetic acid (2,4-D). Feed solutions are prepared by adding each pesticide (100 mg/L glyphosate, 50 μ g/L phorate, 50 mg/L 2,4-D) along with conservative tracer, KBr, in synthetic groundwater. The concentration of the pesticides in effluents is detected by ion chromatography (glyphosate, 2,4-D) and GC-FID (phorate). The Br^? breakthrough curves are employed to estimate the dispersion coefficient and mean pore velocity in each column. Solute transport and reactive models accounting for equilibrium/non-equilibrium sorption and biodegradation are coupled with inverse modeling numerical codes to estimate the kinetic parameters for all pesticides.     

Using polymer mats to biodegrade atrazine in groundwater: laboratory column experiments

Large-scale column experiments were undertaken to evaluate the potential of in situ polymer mats to deliver oxygen into groundwater to induce biodegradation of the pesticides atrazine, terbutryn and fenamiphos contaminating groundwater in Perth, Western Australia. The polymer mats, composed of woven silicone (dimethylsiloxane) tubes and purged with air, were installed in 2-m-long flow-through soil columns. The polymer mats proved efficient in delivering dissolved oxygen to anaerobic groundwater. Dissolved oxygen concentrations increased from <0.2 mg l(-1) to approximately 4 mg l(-1). Degradation rates of atrazine in oxygenated groundwater were relatively high with a zero-order rate of 240-380 microg l(-1) or a first-order half-life of 0.35 days. Amendment with an additional carbon source showed no significant improvement in biodegradation rates, suggesting that organic carbon was not limiting biodegradation. Atrazine degradation rates estimated in the column experiments were similar to rates determined in laboratory culture experiments, using pure cultures of atrazine-mineralising bacteria. No significant degradation of terbutryn or fenamiphos was observed under the experimental conditions within the time frames of the study. Results from these experiments indicate that remediation of atrazine in a contaminated aquifer may be achievable by delivery of oxygen using an in situ polymer mat system.     

Fate of seven pesticides in an aerobic aquifer studied in column experiments

The fate of selected pesticides (bentazone, isoproturon, DNOC, MCPP, dichlorprop and 2,4-D) and a metabolite (2,6-dichlorobenzamide (BAM)) was investigated under aerobic conditions in column experiments using aquifer material and low concentrations of pesticides (approximately 25 microg/l). A solute transport model accounting for kinetic sorption and degradation was used to estimate sorption and degradation parameters. Isoproturon and DNOC were significantly retarded by sorption, whereas the retardation of the phenoxy acids (MCPP, 2,4-D and dichlorprop), BAM and bentazone was very low. After lag periods of 16-33 days for the phenoxy acids and 80 days for DNOC, these pesticides were degraded quickly with 0.-order rate constants of 1.3-2.6 microg/l/day. None of the most probable degradation products were detected.     

Identification of transport processes in column experiments using a frequency domain approach

When a solute transport process is viewed as a dynamic system with input and output, a system identification technique can be used to study it from input-output data. According to the design of excitation signals in the system identification approach, the commonly used rectangular pulse as input signal for column experiments is not optimum because it does not simultaneously meet the requirements for exciting the studied transport process, i.e., possessing frequency components with high enough amplitude and wide enough passband. In this article, stepped sine signals were proposed to replace the rectangular pulse because their amplitude and passband can be independently chosen. The stepped sine signals of concentration were generated by a High Performance Liquid Chromatography (HPLC) and used as the input for the column experiments to identify parameters of the convection-dispersion equation (CDE) and mobile-immobile model (MIM). In order to test the effect of noise on the identification of transport process, numerical experiments were carried out to identify the CDE under white noise when the input was designed as stepped sine functions and rectangular pulse. The results of the numerical experiments showed that the input signal of a sine function was more robust and accurate in process identification than that of a rectangular pulse.     

Characterizing pesticide sorption and degradation in microscale biopurification systems using column displacement experiments

Biopurification systems treating pesticide contaminated water are very efficient, however they operate as a black box. Processes inside the system are not yet characterized. To optimize the performance, knowledge of degradation and retention processes needs to be generated. Therefore, displacement experiments were carried out for four pesticides (isoproturon, bentazone, metalaxyl, linuron) in columns containing different organic mixtures. Bromide, isoproturon and bentazone breakthrough curves (BTCs) were well described using the convection-dispersion equation (CDE) and a first-order degradation kinetic approach. Metalaxyl and linuron BTCs were well described using the CDE model expanded with Monod-type kinetics. Freundlich sorption, first-order degradation and Monod kinetics coefficients were fitted to the BTCs. Fitted values of the distribution coefficient K_f,column were much lower than those determined from batch experiments. Based on mobility, pesticides were ranked as: bentazone > metalaxyl - isoproturon > linuron. Based on degradability, pesticides were ranked as: linuron > metalaxyl - isoproturon > bentazone.     

Characterizing pesticide sorption and degradation in macro scale biopurification systems using column displacement experiments

The efficiency of biopurification systems to treat pesticide-contaminated water was previously studied in microcosms. To validate the obtained results, macrocosm systems were set-up. Four pesticides (linuron, isoproturon, bentazone, and metalaxyl) were continuously applied to ten different organic substrate mixes. Retention of the pesticides was similar and in some cases slightly lower in the macrocosms compared to the microcosms. Differences in retention between the different mixes were however minimal. Moreover, the classification of the retention strength of the pesticides was identical to that observed in microcosms: linuron > isoproturon > metalaxyl > bentazone. Monod kinetics were used to describe delayed degradation, which occurred for isoproturon, metalaxyl and bentazone. No breakthrough of linuron was observed, thus, this pesticide was appointed as the most retained and/or degraded pesticide, followed by isoproturon, metalaxyl and bentazone. Finally, most of the matrix mixes efficient in degrading or retaining pesticides were mixes containing dried cow manure.     

Dissipation and sorption of six commonly used pesticides in two contrasting soils of New Zealand

We investigated dissipation and sorption of atrazine, terbuthylazine, bromacil, diazinon, hexazinone and procymidone in two contrasting New Zealand soils (0–10 cm and 40–50 cm) under controlled laboratory conditions. The six pesticides showed marked differences in their degradation rates in both top- and subsoils, and the estimated DT₅₀ values for the compounds were: 19–120 (atrazine), 10–36 (terbuthylazine), 12–46 (bromacil), 7–25 (diazinon), 8–92 (hexazinone) and 13–60 days for procymidone. Diazinon had the lowest range for DT₅₀ values, while bromacil and hexazinone gave the highest DT₅₀ values under any given condition on any soil type. Batch derived effective distribution coefficient (K _d ^eff) values for the pesticides varied markedly with bromacil and hexazinone exhibiting low sorption affinity for the soils at either depth, while diazinon gave high sorption values. Comparison of pesticide degradation in sterile and non-sterile soils suggests that microbial degradation was the major dissipation pathway for all six compounds, although little influence of abiotic degradation was noticeable for diazinon and procymidone.     

Radionuclide transport and retardation in rock fracture and crushed rock column experiments

Transport and retardation of non-sorbing tritiated water and chloride and slightly sorbing sodium was studied in Syyry area SY-KR7 mica gneiss, in altered porous tonalite and in fresh tonalite. Experiments were performed using dynamic fracture and crushed rock column methods. Static batch method for sodium was introduced to compare retardation values from static and dynamic experiments. The ¹⁴C-PMMA method was used to study the pore structure of matrices. The pore aperture distribution was evaluated from Hg-porosimetry determinations and the surface areas were determined using the B.E.T. method. The flow characteristics and transport behavior of tracers were interpreted using a numerical compartment model for dispersion. The effect of matrix diffusion was calculated using an analytical solution to the advection-matrix diffusion problem in which surface retardation was taken into account. Radionuclide transport behavior in rock fractures was explained on the basis of rock structure.     

Reactive transport of 85Sr in a chernobyl sand column: static and dynamic experiments and modeling

The effects of nonlinear sorption and competition with major cations present in the soil solution on radioactive strontium transport in an eolian sand were examined. Three laboratory techniques were used to identify and quantify the chemical and hydrodynamic processes involved in strontium transport: batch experiments, stirred flow-through reactor experiments and saturated laboratory columns. The major goal was to compare the results obtained under static and dynamic conditions and to describe in a deterministic manner the predominant processes involved in radioactive strontium transport in such systems. Experiments under dynamic conditions, namely flow-through reactor and column experiments, were in very good agreement even though the solid/liquid ratio was very different. The experimental data obtained from the flow-through reactor study pointed to a nonlinear, instantaneous and reversible sorption process. Miscible displacement experiments were conducted to demonstrate the competition between stable and radioactive strontium and to quantify its effect on the 85Sr retardation factor. The results were modeled using the PHREEQC computer code. A suitable cation-exchange model was used to describe the solute/soil reaction. The model successfully described the results of the entire set of miscible displacement experiments using the same set of parameter values for the reaction calculations. The column study revealed that the stable Sr aqueous concentration was the most sensitive variable of the model, and that the initial state of the sand/solution system had also to be controlled to explain and describe the measured retardation factor of radioactive strontium. From these observations, propositions can be made to explain the discrepancies observed between some data obtained from static (batches) and dynamic (reactor and column) experiments. Desorbed antecedent species (stable Sr) are removed from the column or reactor in the flow system but continue to compete for sorption sites in the batch system. Batch experiments are simple and fast, and provide a very useful means of multiplying data. However, interpretation becomes difficult when different species compete for sorption sites in the soil/solution system. A combination of batches, flow-through reactor and column experiments, coupled with hydrogeochemical modeling, would seem to offer a very powerful tool for identifying and quantifying the predominant processes on a cubic decimeter scale (dm3) and for providing a range of radioactive strontium retardation factor as a function of the geochemistry of the soil/solution system.     

Stochastic-convective transport with nonlinear reaction and mixing: application to intermediate-scale experiments in aerobic biodegradation in saturated porous media

Aerobic biodegradation of benzoate by Pseudomonas cepacia sp. in a saturated heterogeneous porous medium was simulated using the stochastic-convective reaction (SCR) approach. A laboratory flow cell was randomly packed with low permeability silt-size inclusions in a high permeability sand matrix. In the SCR upscaling approach, the characteristics of the flow field are determined by the breakthrough of a conservative tracer. Spatial information on the actual location of the heterogeneities is not used. The mass balance equations governing the nonlinear and multicomponent reactive transport are recast in terms of reactive transports in each of a finite number of discrete streamtubes. The streamtube ensemble members represent transport via a steady constant average velocity per streamtube and a conventional Fickian dispersion term, and their contributions to the observed breakthroughs are determined by flux-averaging the streamtube solute concentrations. The resulting simulations were compared to those from a high-resolution deterministic simulation of the reactive transport, and to alternative ensemble representations involving (i) effective Fickian travel time distribution function, (ii) purely convective streamtube transport, and (iii) streamtube ensemble subset simulations. The results of the SCR simulation compare favorably to that of a sophisticated high-resolution deterministic approach.     

Physical versus chemical effects on bacterial and bromide transport as determined from on site sediment column pulse experiments

Twenty-eight bacterial and Br transport experiments were performed in the field to determine the effects of physical and chemical heterogeneity of the aquifer sediment. The experiments were performed using groundwater from two field locations to examine the effects of groundwater chemistry on transport. Groundwater was extracted from multilevel samplers and pumped through 7-cm-long columns of intact sediment or repacked sieved and coated or uncoated sediment from the underlying aquifer. Two bacterial strains, Comamonas sp. DA001 and Paenibacillus polymyxa FER-02, were injected along with Br into the influent end of columns to examine the effect of cell morphology and cell surface properties on bacterial transport. The effects of column sediment grain size and mineral coatings coupled with groundwater geochemistry were also investigated. Significant irreversible attachment of DA001 was observed in the Fe oxyhydroxide-coated columns, but only in the suboxic groundwater where the concentrations of dissolved organic carbon (DOC) were ca. 1 ppm. In the oxic groundwater where DOC was ca. 8 ppm, little attachment of DA001 to the Fe oxyhydroxide-coated columns was observed. This indicates that DOC can significantly reduce bacterial attachment due electrostatic interactions. The larger and more negatively charged FER-02 displayed increasing attachment with decreasing grain size regardless of DOC concentration, and modeling of FER-02 attachment revealed that the presence of Fe and Al coatings on the sediment also promoted attachment. Finally, the presence of Al coatings and Al containing minerals appeared to significantly retard the Br tracer regardless of the concentration of DOC. These findings suggest that DOC in shallow oxic groundwater aquifers can significantly enhance the transport of bacteria by reducing attachment to Fe, Mn and Al oxyhydroxides. This effect appears to be profound for weakly and strongly charged hydrophilic bacteria and may contribute to differences in observations between laboratory experiments versus field-scale investigations particularly if the groundwater pH remains subneutral and Fe oxyhydroxide phases exist. These observation validate the novel approach taken in the experiments outlined here of performing laboratory-scale experiments on site to facilitate the use of fresh groundwater and thus be more representative of in situ groundwater conditions.     

Variability of aquifer sorption properties in a field experiment on groundwater transport of organic solutes: Methods and preliminary results

Methods to characterize the organic solute sorption distribution coefficient, organic carbon content, and specific surface area of aquifer solids from the site of a field experiment on solute transport in groundwater were refined for application to small subsamples of 10-cm depth increments taken from 5-cm diameter cores. Initial results indicate that the average sorption characteristics of the Borden aquifer do not vary appreciably along the trajectory of the solute plumes. However, the sorption distribution coefficient of tetrachloroethylene varied over nearly an order of magnitude among 10-cm depth increments in one core sample. Preliminary evidence suggests that the sorption distribution coefficients for four halogenated organic solutes vary proportionally among core strata. However, the distribution coefficients for sorption of tetrachloroethylene on various depth increments are not well correlated with either organic carbon content or specific surface area, suggesting that as yet unidentified mineral phases may play a significant role in sorption of such solutes by the sandy aquifer solids.     

Comparison of batch, stirred flow chamber, and column experiments to study adsorption, desorption and transport of carbofuran within two acidic soils

Different methods (batch, column and stirred flow chamber experiments) used for adsorption and desorption of carbofuran studies were compared. All tested methods showed that the carbofuran adsorption was higher in the soil with the higher organic matter content, whereas the opposite behaviour was observed for the percentage of carbofuran desorbed. However, different methods have revealed some discrepancies in carbofuran adsorption/desorption kinetics. Although batch method showed interesting data on equilibrium experiments, such as a low heterogeneity for the carbofuran adsorption sites independent of soil organic matter content, it had some disadvantages for carbofuran adsorption/desorption kinetic studies. The disadvantages were related with the excessive limitations of this method on kinetics, i.e., no difference could be detected between different soils. However, with column and stirred flow chamber methods the carbofuran adsorption/desorption kinetics of different soils could be compared. Moreover, the absolute values of carbofuran adsorption/desorption and its rate were higher in the stirred flow chamber than in the batch and column experiments. Using stirred flow chamber experiments the carbofuran desorption was significantly faster than its adsorption, whereas carbofuran using column experiments they were similar. These discrepancies should be considered when the results obtained only with one method is discussed.     

3(in Chinese)基于随机-模糊耦合的填埋场地下水污染风险评价方法

为分析参数不确定性对填埋场渗漏风险评估结果的影响,构建了填埋场地下水污染风险评价的物理过程模型,在此基础上,分别采用模糊理论和概率理论刻画模糊不确定性参数和随机不确定性参数,同时采用基于随机理论的Monte Carlo方法模拟模糊不确定参数,最终构建了基于模糊随机耦合的填埋场地下水污染风险评价方法。采用该模型对东北某一般工业固废填埋场进行案例研究,结果表明,实测浓度在模型模拟的的浓度区间(10%~90%分位值浓度)之内。说明本模型构建的模糊-随机耦合的地下水污染风险评价模型能较准确地预测地下水中污染物实际浓度,可以用于填埋场地下水污染风险评价.风险评估结果表明,该填埋场地下水的潜在污染物为As和Mn,其中As为主要健康风险物质,其非致癌风险值超过风险可接受水平的概率为22%,致癌风险超过10-4的概率为33%,超过10-5的概率为86%,应该采取措施控制含As填埋废物中As的溶出,降低其环境风险;Mn的非致癌风险值小于风险可接受水平的概率为100%,无风险。     

Using the multiple cell balance method to solve the problem of two-dimensional groundwater flow and contaminant transport with nonequilibrium sorption

The problem of large-scale contamination of groundwater by relatively low levels of organic contaminants is most frequently addressed by extracting and treating the impacted groundwater. This pump-and-treat strategy is often unsuccessful because of difficulties encountered in recovering the contaminants from relatively immobile zones within the porous medium. These zones can exist at the particle scale, as intraparticle or intra-aggregate porosity, and at the larger scales, as low-permeability layers or lenses interspersed in substantially more permeable layers. This work focuses on achieving an efficient numerical solution to a system of groundwater flow and contaminant transport equations that sufficiently captures the dynamics of slow desorption in a two-dimensional porous medium. The conceptual model and governing equations are presented. A numerical method for solving the governing equations, the upstream-weighted, multiple cell balance (UMCB) method, is proposed. The UMCB algorithm has been employed previously for the case of solute transport with equilibrium sorption, and is extended here to the nonequilibrium case. The approach employs a finite-element basis function and a finite-difference local mass balance, and is designed to reduce computational and storage requirements, while minimizing the mass balance error. The computational grid is formed by division of the flow domain into triangular elements. An invented node at the center of each element divides the element into three subtriangular regions. By linking the center of each triangular element and the mid-point of each elemental side, a multiangular region, referred to as an exclusive subdomain, is defined. The discretized system of governing equations is derived from the integral form that describes the mass balance in the exclusive subdomain of each node. The paper details the application of the numerical method, and demonstrates that the method is reasonably accurate and computationally efficient for a two-dimensional domain subject to nonequilibrium sorption.     

UV-C as a means to combat biofilm proliferation on prehistoric paintings: evidence from laboratory experiments

A laboratory investigation of UV-C effects was conducted over a 62-h period: a much higher dose than in classic UV-C treatment was applied to five pigments and two painting binders used by prehistoric humans. Colorimetric parameters were compared to a control to see if UV-C can change pigment and binder color. Infrared spectroscopy, scanning electron microscopy, inductively coupled plasma and X-ray crystallography were also carried out to confirm colorimetric measurement. In order to understand how microorganism may physically deteriorate paintings, limestone blocks were painted and monitored until their complete colonization by algae, cyanobacteria, fungi and/or mosses. The results show that UV-C has no effect on mineral compounds. Conversely, it is noteworthy that binder color changed under both UV-C light conditions as well as in visible light. Concerning painted blocks, a fast proliferation has been observed with deterioration of the paintings. These results show the high importance of treating biofilm as soon as possible. Moreover, these findings may be a promising avenue inducing cave managers to use friendly UV-C light to treat contaminated cave paintings and also in the prevention of biodeterioration by lampenflora.     

The influence of mass transfer on solute transport in column experiments with an aggregated soil

The spreading of concentration fronts in dynamic column experiments conducted with a porous, aggregated soil is analyzed by means of a previously documented transport model (DFPSDM) that accounts for longitudinal dispersion, external mass transfer in the boundary layer surrounding the aggregate particles, and diffusion in the intra-aggregate pores. The data are drawn from a previous report on the transport of tritiated water, chloride, and calcium ion in a column filled with Ione soil having an average aggregate particle diameter of 0.34 cm, at pore water velocities from 3 to 143 cm/h. The parameters for dispersion, external mass transfer, and internal diffusion were predicted for the experimental conditions by means of generalized correlations, independent of the column data. The predicted degree of solute front-spreading agreed well with the experimental observations. Consistent with the aggregate porosity of 45%, the tortuosity factor for internal pore diffusion was approximately equal to 2. Quantitative criteria for the spreading influence of the three mechanisms are evaluated with respect to the column data. Hydrodynamic dispersion is thought to have governed the front shape in the experiments at low velocity, and internal pore diffusion is believed to have dominated at high velocity; the external mass transfer resistance played a minor role under all conditions. A transport model such as DFPSDM is useful for interpreting column data with regard to the mechanisms controlling concentration front dynamics, but care must be exercised to avoid confounding the effects of the relevant processes.     

Removal by sorption and in situ biodegradation of oil spills limits damage to marine biota: a laboratory simulation

This study examined the efficiency of cotton grass fibers in removing diesel oil from the surface of water in conditions prevailing in the Baltic Sea. The effect of low temperature, salinity, and bacterial amendments were tested in laboratory-scale set-ups, whereas 600-L mesocosms filled with Baltic Sea water were used for testing the effects of diesel oil and rapid removal of the oil on microorganisms, phytoplankton, and mussels. Cotton grass proved to be an excellent sorbent for diesel oil from the water surface at a low temperature. Inoculation with diesel-enriched microorganisms enhanced degradation of oil significantly in laboratory-scale experiments. In mesocosm experiments, the addition of diesel oil (0.66 mg L(-1), 0.533 L m(-2)) to the basins resulted in higher microbial density than in all other basins, including inoculated ones, suggesting that the Baltic Sea contains indigenous hydrocarbon degraders. The removal of oil with cotton grass significantly improved the survival of mussels in the mesocosm tests: 100% mortality in diesel basins versus 0% mortality in basins with cotton grass, respectively. However, the surviving mussels suffered from histopathological changes such as inflammatory responses, degenerations, and cell death. The observed rescuing effect was observable even when the cotton grass-bound oil was left in the water. The results underline the importance of rapid action in limiting damage caused by oil spills.     

Pilot-scale demonstration of a two-stage methanotrophic bioreactor for biodegradation of trichloroethylene in groundwater

A two-stage methanotrophic bioreactor system was developed for remediation of water contaminated with TCE and other chlorinated, volatile, aliphatic hydrocarbons. The first stage of the reactor was a suspended-growth culture vessel using a bubbleless methane-transfer device. The second stage was a plug-flow bioreactor supplied with contaminated groundwater and cell suspension from the culture vessel. The test objectives were to determine the applicability of microbial culture conditions reported in the literature for continuous, pilot-scale TCE treatment; the technical feasibility of plug-flow bioreactor design for treatment of TCE; and the projected economic competitiveness of the technology considering the cost of methane for growth of methanotrophs. The methanotrophic organism used in the study was Methylosinus trichosporium OB3b. Information on system operation was obtained in bench tests prior to conducting the pilot tests. In bench- and pilot-scale tests, variability in the degree of TCE degradation and difficulty in maintaining the microbial culture activity led to short periods of satisfactory biotreatment. Further development of the microbial culture system will be required for long-term operation. During transient periods of high TCE degradation activity, the bioreactor concept proved feasible by exhibiting both a high degree of TCE biodegradation (typically about 90% at influent TCE concentrations of 0.5-4 ppm) and a close approximation to first-order reactor kinetics throughout the length of the reactor. Actual methane usage in the pilot-scale reactor resulted in projected methane costs of $0.33 per 1000 gallons of water treated. This cost theoretically would be reduced by system modifications. The theoretical minimum methane cost was approximately $0.05 per 1000 gallons.     

一种新嗜冷菌JLNY02降解地下水中阿特拉津的研究

从某农药厂排污口采集污泥样品，通过富集培养，从中分离筛选出一株阿特拉津高效降解菌JLNY02，并进一步对其降解的影响因素进行研究。在10℃的条件下降解阿特拉津，其降解率可达81.8%，而在高温下的降解率较低，仅31．4％。