Evaluation of a multiresidue method for pesticides in cereals using supercritical fluid extraction and gas chromatographic detection

Supercritical fluid extraction (SFE) was evaluated to be applied for residue analysis of 22 gas chromatography/electron capture detector-nitrogen phosphorus detector (GC/ECD-NPD) amenable pesticides in rice, wild rice and wheat. Samples were extracted with supercritical carbon dioxide at 200 atm pressure and 50°C temperature, using methanol as a static modifier. Mean recoveries obtained with the proposed SFE method at two spiking levels with four replicates per level are compared with those obtained with an ethyl acetate-based solvent extraction/gel permeation chromatography (GPC) clean up method. Both methods gave consistent high recoveries for almost all the pesticides from all the commodities with overall mean recoveries higher than 70% with relative standard deviations lower than 20%. Remarkable exceptions were captafol and dimethoate, for which low and/or non-reproducible recoveries were obtained with the SFE method. Residue levels determined with both methods in nine different incurred samples of wheat, containing some of the studied pesticides, were very similar, but, in all cases, slightly higher levels were determined with the SFE method.     

Determination of pentachlorophenol (PCP) in waste wood--method comparison by a collaborative trial

Two independently developed and validated procedures for the determination of pentachlorophenol (PCP) in waste wood were compared by means of a collaborative trial. Both methods foresee quantification of PCP by gas chromatography (GC-ECD) after acetylation and differ with regard to the use of methanol or toluene/sulphuric acid, respectively, as solvent in the sonication extraction step. Test samples with established analyte homogeneity were prepared from a ground "real life" starting material. A total of 23 participating laboratories with experience in wood preservative analysis were instructed to apply both methods to three levels of content in the range of 0.5-20 mg PCP/kg. In case of the toluene/sulphuric acid extraction, lower recoveries and higher interlaboratory dispersion of results at the higher PCP contents were observed. Seen against the background of the Horwitz equation a reproducibility standard deviation of approximately 19% for the methanol extraction at the 4.5 mg/kg level meets the requirement for a sound analytical method. Thus, the sonication extraction procedure with methanol has been annexed as a reference method to the German waste wood regulation.     

Evaluation of pressure treated wood impact on landfill waste decomposition using a methane yield assay

Research was conducted to investigate the potential impact of CCA-treated wood and other arsenic-free Cu-based preservative-treated wood on microorganisms, involved in the anaerobic decomposition of waste in landfills. Wood preservatives used included alkaline copper quat (ACQ), copper citrate (CC), copper boron azole (CBA), copper dimethyldithiocarbamate (CDDC), and chromated copper arsenate (CCA). The biochemical methane potential (BMP) assay was used to estimate the possible impacts. The methane yields of mixtures of preservative-treated wood or untreated wood with cellulose (group 1) and these wood samples only (group 2) were determined. An analysis of variance (ANOVA) test found that there were no significant differences among methane yields results in either group 1 or group 2, at the 0.05 level of significance. The results indicate that under the conditions tested, none of the treated wood products evaluated were toxic to the methane-producing organisms. At the end of the assays, test bottle contents were analyzed for Cu, Cr, and As. When the fraction of each metal in the solution (relative to original metal in the wood, leachability %) was examined, As was present at the great extent. The leachability of As was in the range from 15.1% to 21.7% while relatively low leachability (1.7-7.6%) of Cu was observed.     

Increased bioavailability of metals in two contrasting agricultural soils treated with waste wood-derived biochar and ash

Recycled waste wood is being increasingly used for energy production; however, organic and metal contaminants in by-products produced from the combustion/pyrolysis residue may pose a significant environmental risk if they are disposed of to land. Here we conducted a study to evaluate if highly polluted biochar (from pyrolysis) and ash (from incineration) derived from Cu-based preservative-treated wood led to different metal (e.g., Cu, As, Ni, Cd, Pb, and Zn) bioavailability and accumulation in sunflower (Helianthus annuus L.). In a pot experiment, biochar at a common rate of 2 % w/w, corresponding to ～50 t ha^?1, and an equivalent pre-combustion dose of wood ash (0.2 % w/w) were added to a Eutric Cambisol (pH 6.02) and a Haplic Podzol (pH 4.95), respectively. Both amendments initially raised soil pH, although this effect was relatively short-term, with pH returning close to the unamended control within about 7 weeks. The addition of both amendments resulted in an exceedance of soil Cu statutory limit, together with a significant increase of Cu and plant nutrient (e.g., K) bioavailability. The metal-sorbing capacity of the biochar, and the temporary increase in soil pH caused by adding the ash and biochar were insufficient to offset the amount of free metal released into solution. Sunflower plants were negatively affected by the addition of metal-treated wood-derived biochar and led to elevated concentration of metals in plant tissue, and reduced above- and below-ground biomass, while sunflower did not grow at all in the Haplic Podzol. Biochar and ash derived from wood treated with Cu-based preservatives can lead to extremely high Cu concentrations in soil and negatively affect plant growth. Identifying sources of contaminated wood in waste stream feedstocks is crucial before large-scale application of biochar or wood ash to soil is considered.     

Elemental analysis of ash residue from combustion of CCA treated wood waste before and after electrodialytic extraction

Element distribution in a combined fly ash and bottom ash from combustion of copper chromate arsenate (CCA) treated wood waste was investigated by scanning electron microscopy (SEM/EDX) before and after electrodialytic extraction. The untreated ash contained various particles, including pieces of incompletely combusted wood rich in Cr and Ca, and irregular particles rich in Si, Al and K. Cr was also found incorporated in silica-based matrix particles. As was associated with Ca in porous (char) particles, indicating that Ca-arsenates had been formed during combustion. Cu was associated with Cr in the incompletely combusted wood pieces and was also found in almost pure form in a surface layer of some matrix particles - indicating surface condensation of volatile Cu species. In treated ash, Ca and As were no longer found together, indicating that Ca-arsenates had been dissolved due to the electrodialytic treatment. Instead particles rich in Ca and S were now found, indicating precipitation of Ca-sulphates due to addition of sulphuric acid in connection with the electrodialytic treatment. Cu and Cr were still found associated with incompletely combusted wood particles and incorporated in matrix particles. Chemical analyses of untreated and treated ash confirmed that most As, but only smaller amounts of Cu and Cr was removed due to the electrodialytic extraction. Overall metal contents in the original ash residue were: 1.4 g As, 2.76 g Cu and 2.48 g Cr, after electrodialytic extraction these amounts were reduced by 86% for As, 15% for Cu and 33% for Cr.     

Influence of soil properties on bioaccumulation of 14C-simazine in earthworms Eisenia foetida

The toxicity of pesticides has been evaluated by several methods including tests with earthworms in both artificial and natural soils treated with the compounds. The ecological niches of earthworms make them good bioindicators of soil contamination. The bioaccumulation of 14C-simazine (6-chloro-N2-N4-diethyl- 1,3,5-triazine-2,4-diamine) was evaluated in earthworms (Eisenia foetida) maintained during three months in two substrates with different physical-chemical characteristics. The substrates were treated with 3.0 mg and 330 kBq of 14C-simazine kg(-1) substrate. Results indicated that worms did not influence simazine dissipation in both substrates as indicated by similar recoveries and with no statistical differences with and without earthworms. The radiocarbon recoveries were 86.8 and 95.3%, respectively in the substrates with lower and higher organic matter contents with earthworms, and 91.0 and 107.4% in the same substrates without worms. However, in earthworms the recoveries were statistically higher when they were maintained in the substrate with lower amount of organic matter (0.89%) than from the higher one (0.33%). Consequently, 14C-simazine bioconcentration factor (BCF) was also greater in the substrate with lower organic matter (6.89+/-1.55) than in the substrate with higher organic matter content (0.88+/-0.06). The results suggest that the higher soil organic matter content will cause lower probability of contamination of soil organisms with simazine.     

A comparative study on the recovery of polycyclic aromatic hydrocarbons from fly ash and lignite coal

The recovery of polycyclic aromatic hydrocarbons (PAHs) from lignite coal burnt in Greek power stations and the fly ash produced is examined comparatively using Soxhlet, ultrasonic and accelerated solvent extraction procedures with various organic solvents. Soxhlet using toluene/methanol mixture and accelerated solvent extraction/toluene were found to be the most efficient methods for fly ash PAHs, yielding average recoveries of about 80%. The accelerated solvent extraction/toluene procedure was superior for lignite PAHs, yielding 96% average recovery, whereas ultrasonic and Soxhlet extraction yielded relatively lower recoveries (75% and 67%, respectively).     

Effects of residue incorporation and plant growth on soil labile organic carbon and microbial function and community composition under two soil moisture levels

This study investigates the effects of residue incorporation coupled with plant growth and soil moisture level on wheat biomasses, soil nutrients, labile organic carbon (LOC), microbial metabolic profiles, and community composition. Four management practices were used in a 180-day pot experiment: (1) control (CON), (2) maize (Zea mays L.) residue incorporation without plants (MR), (3) wheat (Triticum aestivum L.) plants without maize residue (WP), and (4) maize residue incorporation with wheat plants (MRWPs). Each management practice included soil moisture at both 40 and 80% of field capacity. At wheat harvest, soil nutrient contents in the WP and MRWP treatments were significantly lower than in the CON and MR treatments. In comparison with the CON treatment, MR, WP, and MRWP treatments resulted in 35, 23, and 67% increases in dissolved organic carbon content; 17, 12, and 34% increases in hot-water extractable organic carbon content; and 78, 50, and 150% increases in microbial biomass carbon content. Furthermore, microbial utilizations of carboxylic acids and polymer carbon sources in the MR, WP, and MRWP treatments were 261 and 88%, 239 and 105%, and 300 and 126% higher than in the CON treatment. The MR and CON treatments had similar phospholipid fatty acid (PLFA) content but the WP and MRWP treatments had significantly increased gram-negative content and changes to community composition compared with the CON and MR treatments. The wheat biomass, LOC, and PLFA contents significantly increased with greater soil moisture. Overall, these results suggest an additive effect of residue incorporation and plant growth on LOC contents, primarily due to the changes in microbial utilization of carbon sources and community composition.     

Comparison of two sample preparation methods for analysis of organochlorine pesticides residues in fish muscle

The aim of this study was to compare recoveries of organochlorine pesticides (heptachlor, α-HCH, β-HCH, γ-HCH, op'-DDD, pp'-DDD, pp'-DDE, op'-DDT, pp'-DDT) from fish muscle dried by two alternative methods: (i) grinding with anhydrous sodium sulphate and (ii) freeze drying. Pesticide residues content was determined by gas chromatography-mass spectrometry (GS-MS) method. For four pesticides (γ-HCH, α-HCH, heptachlor and pp;-DDD) in four of five fish species, higher recoveries were obtained from the freeze-dried samples. For five remaining pesticides, correlations between fish species and drying method were not found. The results of this study do not clearly indicate which drying method caused lower losses of analytes. Recoveries from the freeze-dried samples ranged from 69.9 to 117.6 %, while recoveries from the samples ground with sodium sulphate varied from 64.4 to 126.7 %. Either of the methods gave satisfactory recoveries and they both can be used interchangeably.     

Comparison of two sample preparation methods for analysis of organochlorine pesticides residues in fish muscle

The aim of this study was to compare recoveries of organochlorine pesticides (heptachlor, α-HCH, β-HCH, γ-HCH, op′-DDD, pp′-DDD, pp′-DDE, op′-DDT, pp′-DDT) from fish muscle dried by two alternative methods: (i) grinding with anhydrous sodium sulphate and (ii) freeze drying. Pesticide residues content was determined by gas chromatography-mass spectrometry (GS-MS) method. For four pesticides (γ-HCH, α-HCH, heptachlor and pp;-DDD) in four of five fish species, higher recoveries were obtained from the freeze-dried samples. For five remaining pesticides, correlations between fish species and drying method were not found. The results of this study do not clearly indicate which drying method caused lower losses of analytes. Recoveries from the freeze-dried samples ranged from 69.9 to 117.6 %, while recoveries from the samples ground with sodium sulphate varied from 64.4 to 126.7 %. Either of the methods gave satisfactory recoveries and they both can be used interchangeably.     

Sorbent-assisted liquid-liquid extraction (Chem-Elut) of polychlorinated biphenyls, dibenzo-p-dioxins and dibenzofurans in the lipid fraction of human blood plasma

This work compares two lipid extraction methods for determining 24 polychlorinated biphenyls (PCBs), seven dibenzo-p-dioxins (PCDDs) and ten dibenzofurans (PCDFs) in human blood plasma. The first method was based on conventional liquid-liquid partitioning with chloroform-methanol and the other made use of a sorbent (Chem-Elut) to facilitate the partitioning of lipids into a mixture of hexane and 2-propanol. A multi-layer-silica column including acid- and base-impregnated silica gel was used to reduce the amounts of lipid present in the samples before a basic alumina clean-up step and activated carbon fractionation of planar analytes (PCDD/Fs and non-ortho-PCBs) and non-planar analytes (including ortho-chlorinated PCBs). Gas chromatography coupled to high resolution mass spectrometry was used to identify and quantify the analytes in the two fractions. The wet weight based concentrations obtained by the two methods were in agreement but both methods suffer from large organic solvent consumption. The toxic equivalencies derived for PCBs and PCDD/Fs using the two methods were also in agreement. However, the chloroform-methanol method gave slightly higher lipid recoveries, although with greater variation, than the sorbent-assisted method. Nevertheless, despite giving lower lipid recoveries, the sorbent-assisted method has advantages in ease of use and applicability to whole blood samples. The formation of emulsions was avoided with the Chem-Elut method, which probably explains the lower variability in the lipid determinations.     

Bioindication of air pollution effects near a copper smelter in Brazil using mango trees and soil microbiological properties

A field study near the copper smelter of a large industrial complex examined air pollution effects on vegetation and soil parameters in Cama?ari (northeast Brazil). Close to the smelter, soil pH-value was lower and total acidity as well as organic carbon contents were higher compared with a site far from the source and two reference sites. The acidification of top soil particularly and the drastically enhanced plant-available copper concentrations were caused by atmospheric deposition. High sulphur and copper deposition significantly reduced microbial biomass and altered functional diversity of soil microorganisms (arylsulphatase and xylanase). Large accumulations of sulphur, arsenic and copper were detected in mango leaves (Mangifera indica) growing downwind from the smelter suggesting potential food chain-mediated risk.     

Fungal biodegradation of CCA-treated wood and removal of its metal components

In the present study, 5 isolates of brown-rot fungi were used for fungal bioprocessing (FB) of chromated copper arsenate (CCA)-treated wood wastes: Antrodia vaillantii SEL8501, Fomitopsis palustris TYP0507 and TYP6137, and Crustoderma sp. KUC8065 and KUC8611. The isolates showed notable capacity for the degradation of treated wood and removal of CCA components via the American Wood Protection Association soil block test. Among them, Crustoderma sp. KUC8611 effectively decayed the treated wood, causing a mass loss of up to 60%. F. palustris caused extensive leaching of CrO₃ of up to 79% and As₂O₅ of up to 87%, but only moderate leaching of CuO of up to 50%. This high capacity for removal of CrO₃ and As₂O₅ showed a strong logarithmic relationship with the amount of oxalic acid produced in the decayed wood. The majority of metals removed from treated wood during the decay process were deposited in the soil and feeder strip. Further investigation will be required to establish the capability of selected fungi for FB of full-sized lumber treated with CCA.     

Growth inhibition of bloom forming cyanobacterium Microcystis aeruginosa by green route fabricated copper oxide nanoparticles

The cyanobacterium Microcystis aeruginosa can potentially proliferate in a wide range of freshwater bionetworks and create extensive secondary metabolites which are harmful to human and animal health. The M. aeruginosa release toxic microcystins that can create a wide range of health-related issues to aquatic animals and humans. It is essential to eliminate them from the ecosystem with convenient method. It has been reported that engineered metal nanoparticles are potentially toxic to pathogenic organisms. In the present study, we examined the growth inhibition effect of green synthesized copper oxide nanoparticles against M. aeruginosa. The green synthesized copper oxide nanoparticles exhibit an excitation of surface plasmon resonance (SPR) at 270 nm confirmed using UV–visible spectrophotometer. The dynamic light scattering (DLS) analysis revealed that synthesized nanoparticles are colloidal in nature and having a particle size of 551 nm with high stability at ?26.6 mV. The scanning electron microscopy (SEM) analysis shows that copper oxide nanoparticles are spherical, rod and irregular in shape, and consistently distributed throughout the solution. The elemental copper and oxide peak were confirmed using energy dispersive x-ray analysis (EDAX). Fourier-transform infrared (FT-IR) spectroscopy indicates the presence of functional groups which is mandatory for the reduction of copper ions. Besides, green synthesized copper oxide nanoparticles shows growth inhibition against M. aeruginosa. The inhibition efficiency was 31.8 % at lower concentration and 89.7 % at higher concentration of copper oxide nanoparticles, respectively. The chlorophyll (a and b) and carotenoid content of M. aeruginosa declined in dose-dependent manner with respect to induction of copper oxide nanoparticles. Furthermore, we analyzed the mechanism behind the cytotoxicity of M. aeruginosa induced by copper oxide nanoparticles through evaluating membrane integrity, reactive oxygen species (ROS), and mitochondrial membrane potential (Δψm) level. The results expose that there is a loss in membrane integrity with ROS formation that leads to alteration in the Δψm, which ends up with severe mitochondrial injury in copper oxide nanoparticles treated cells. Hence, green way synthesized copper oxide nanoparticles may be a useful selective biological agent for the control of M. aeruginosa.     

Fungicidal values of bio-oils and their lignin-rich fractions obtained from wood/bark fast pyrolysis

Pine wood, pine bark, oak wood and oak bark were pyrolyzed in an auger reactor. A total of 16 bio-oils or pyrolytic oils were generated at different temperatures and residence times. Two additional pine bio-oils were produced at the National Renewable Energy Laboratory in a fluidized-bed reactor at different temperatures. All these bio-oils were fractionated to obtain lignin-rich fractions which consist mainly of phenols and neutrals. The pyrolytic lignin-rich fractions were obtained by liquid-liquid extraction. Whole bio-oils and their lignin-rich fractions were studied as potential environmentally benign wood preservatives to replace metal-based CCA and copper systems that have raised environmental concerns. Each bio-oil and several lignin-rich fractions were tested for antifungal properties. Soil block tests were conducted using one brown-rot fungus (Gloeophyllum trabeum) and one white-rot fungus (Trametes versicolor). The lignin-rich fractions showed greater fungal inhibition than whole bio-oils for a impregnation solution 10% concentration level. Water repellence tests were also performed to study wood wafer swelling behavior before and after bio-oil and lignin-rich fraction treatments. In this case, bio-oil fractions did not exhibit higher water repellency than whole bio-oils. Comparison of raw bio-oils in soil block tests, with unleached wafers, at 10% and 25% bio-oil impregnation solution concentration levels showed excellent wood preservation properties at the 25% level. The good performance of raw bio-oils at higher loading levels suggests that fractionation to generate lignin-rich fractions is unnecessary. At this more effective 25% loading level in general, the raw bio-oils performed similarly. Prevention of leaching is critically important for both raw bio-oils and their fractions to provide decay resistance. Initial tests of a polymerization chemical to prevent leaching showed some success.     

Field-scale leaching of arsenic, chromium and copper from weathered treated wood

Earlier studies documented the loss of wood preservatives from new wood. The objective of this study was to evaluate losses from weathered treated wood under field conditions by collecting rainfall leachate from 5 different wood types, all with a surface area of 0.21 m². Wood samples included weathered chromate copper arsenate (CCA) treated wood at low (2.7 kg/m³), medium (4.8 kg/m³) and high (35.4 kg/m³) retention levels, new alkaline copper quat (ACQ) treated wood (1.1 kg/m³ as CuO) and new untreated wood. Arsenic was found to leach at a higher rate (100 mg in 1 year for low retention) than chromium and copper (<40 mg) in all CCA-treated wood samples. Copper leached at the highest rate from the ACQ sample (670 mg). Overall results suggest that metals' leaching is a continuous process driven by rainfall, and that the mechanism of release from the wood matrix changes as wood weathers.     

Evaluation of solid sorbents for sampling aliphatic and aromatic nitro compounds in work-room air

Amberlite XAD-2 and XAD-7 porous polymers were evaluated for the solid sampling of aliphatic and aromatic nitro compounds in work-room air. With the use of solvent desorption, XAD-2 gave 80–100% recovery of nitroaromatics, and XAD-7 85–100% recovery of nitroaliphatics. The compounds studied were nitromethane, nitroethane, 2-nitropropane, nitrobenzene, $\text{m}$-dinitrobenzene and 2,4,6-trinitrotoluene. All six compounds gave very poor recoveries from activated charcoal.     

Natural deep eutectic solvent mediated pretreatment of rice straw: bioanalytical characterization of lignin extract and enzymatic hydrolysis of pretreated biomass residue

The present investigation demonstrated pretreatment of lignocellulosic biomass rice straw using natural deep eutectic solvents (NADESs), and separation of high-quality lignin and holocellulose in a single step. Qualitative analysis of the NADES extract showed that the extracted lignin was of high purity (>90 %), and quantitative analysis showed that nearly 60?±?5 % (w/w) of total lignin was separated from the lignocellulosic biomass. Addition of 5.0 % (v/v) water during pretreatment significantly enhanced the total lignin extraction, and nearly 22?±?3 % more lignin was released from the residual biomass into the NADES extract. X-ray diffraction studies of the untreated and pretreated rice straw biomass showed that the crystallinity index ratio was marginally decreased from 46.4 to 44.3 %, indicating subtle structural alterations in the crystalline and amorphous regions of the cellulosic fractions. Thermogravimetric analysis of the pretreated biomass residue revealed a slightly higher T _dcp (295 °C) compared to the T _dcp (285 °C) of untreated biomass. Among the tested NADES reagents, lactic acid/choline chloride at molar ratio of 5:1 extracted maximum lignin of 68?±?4 mg g^?1 from the rice straw biomass, and subsequent enzymatic hydrolysis of the residual holocellulose enriched biomass showed maximum reducing sugars of 333?±?11 mg g^?1 with a saccharification efficiency of 36.0?±?3.2 % in 24 h at 10 % solids loading.     

As(V) retention on soils and forest by-products and other waste materials

As(V) retention capacity is determined by means of adsorption/desorption trials performed for coarse and fine ground mussel shell, forest and vineyard soils with or without fine shell, pine wood ash, oak wood ash, pine sawdust and slate-processing fines. Pine ash shows the highest arsenic retention potential (with >97 % adsorption and ≤1 % desorption), followed by shell-amended forest soil (adsorption between 96 and 92 %), by un-amended forest soil (adsorption between 98 and 86 %) and by the amended vineyard soil (adsorption between 92 and 75 %). Sawdust is the material with the lowest arsenic retention capacity in most cases, with un-amended vineyard soil also showing poor results. In the case of oak ash, As(V) percentage adsorption becomes higher with increasing added arsenic concentrations, while this increase in added arsenic causes lower percentage adsorption in the case of slate fines. Regarding adsorption ability, As(V) adsorption data were fitted to Freundlich and Langmuir models, showing good fitting, with pine ash and shell-amended forest soil having the highest K _F values. In view of that, mussel shell amendment would be useful to increase arsenic retention on forest and vineyard soils, while pine ash could be used to retain arsenic even from wastewaters.     

Fractionation of heavy metals in liquefied chromated copper arsenate 9-treated wood sludge using a modified BCR-sequential extraction procedure

Chromated copper arsenate (CCA)-treated wood was liquefied with polyethylene glycol/glycerin and sulfuric acid. After liquefaction, most CCA metals (98% As, 92% Cr, and 83% Cu) were removed from liquefied CCA-treated wood by precipitation with calcium hydroxide. The original CCA-treated wood and liquefied CCA-treated wood sludge were fractionated by a modified Community Bureau of Reference (BCR) sequential extraction procedure. The purpose of the BCR-sequential extraction used in this study was to examine the availability of CCA metals in treated wood for reuse. Both As and Cr had a slightly higher concentration in the sludge sample than in original CCA-treated wood. The sequential extraction showed that As and Cr were principally existed in an oxidizable fraction (As, 67%; Cr, 88%) in original CCA-treated wood. Only 1% of both As and Cr were extracted by hot nitric acid with the last extraction step. The distribution of As and Cr changed markedly in liquefied CCA-treated wood sludge.The amount of As in the exchangeable/acid extractable fraction increased from 16% to 85% while the amount of Cr increased from 3% to 54%. Only about 3% of As was present in the oxidizable fraction. However, there was still about 34% of Cr in the same fraction. Based on these results from sequential extraction procedures, it can be concluded that the accessibilities of CCA metals increase markedly by the liquefaction–precipitation process.