Use of thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS) on identification of odorant emission focus by volatile organic compounds characterisation

Volatile organic compounds (VOCs) from several different municipal solid wastes’ treatment plants in Mallorca (Spain) have been analysed by thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS). Ambient (immission) air was collected during February and March 2011 by active sampling onto sorbents Tenax™ TA and Carboxen™ 1000. The study presents the chemical characterisation of 93 volatile organic compounds (VOCs) from an overall set of 84 immission air samples. 70 VOCs were positively identified.The linear fit for all 93 external standard calibration, from 10 mg L⁻¹ to 150 mg L⁻¹ (n = 4), was within the range 0.974 < r² < 0.998. Limits of detection of the method (LOD) for all the standards were within the range 1.1-4,213 pg, as the absolute standard amount spiked into sorbent tubes in 1 μL standard mixture (dissolved in methanol).Overall results stated systematic correlation between waste’s nature and VOCs’ air composition. Organic wastes show main contribution of terpenes, waste water sludge residues’ of reduced sulphured compounds (RSCs) and municipal solid wastes show contribution of a wide sort of VOCs. The use of a chemometric approach for variable’s reduction to 12 principal components enables evaluation of similarities and dissimilarities between facilities. PCA clearly related samples to its corresponding facility on the basis of their VOCs composition and the ambient temperature.     

Evaluation of a novel high throughput screening tool for relative emissions of industrial chemicals used in chemical products

Tens of thousands of chemicals are currently marketed worldwide, but only a small number of these compounds has been measured in effluents or the environment to date. The need for screening methodologies to select candidates for environmental monitoring is therefore significant. To meet this need, the Swedish Chemicals Agency developed the Exposure Index (EI), a model for ranking emissions to a number of environmental matrices based on chemical quantity used and use pattern. Here we evaluate the EI. Data on measured concentrations of organic chemicals in sewage treatment plants, one of the recipients considered in the EI model, were compiled from the literature, and the correlation between predicted emission levels and observed concentrations was assessed by linear regression analysis. The adequacy of the parameters employed in the EI was further explored by calibration of the model to measured concentrations. The EI was found to be of limited use for ranking contaminant levels in STPs; the r² values for the regressions between predicted and observed values ranged from 0.02 (p = 0.243) to 0.14 (p = 0.007) depending on the dataset. The calibrated version of the model produced only slightly better predictions although it was fitted to the experimental data. However, the model is a valuable first step in developing a high throughput screening tool for organic contaminants, and there is potential for improving the EI algorithm.     

Volatile organic compound concentrations, emission rates, and source apportionment in newly-built apartments at pre-occupancy stage

The present study investigated the indoor concentrations of selected volatile organic compounds (VOCs) and formaldehyde and their indoor emission characteristics in newly-built apartments at the pre-occupancy stage. In total, 107 apartments were surveyed for indoor and outdoor VOC concentrations in two metropolitan cities and one rural area in Korea. A mass balanced model was used to estimate surface area-specific emission rates of individual VOCs and formaldehyde. Seven (benzene, ethyl benzene, toluene, m,p-xylene, o-xylene, n-hexane, and n-heptane) of 40 target compounds were detectable in all indoor air samples, whereas the first five were detected in all outdoor air samples. Formaldehyde was also predominant in the indoor air samples, with a high detection frequency of 96%. The indoor concentrations were significantly higher than the outdoor concentrations for aromatics, alcohols, terpenes, and ketones. However, six halogenated VOCs exhibited similar concentrations for indoor and outdoor air samples, suggesting that they are not major components emitted from building materials. It was also suggested that a certain portion of the apartments surveyed were constructed by not following the Korean Ministry of Environment guidelines for formaldehyde emissions. Toluene exhibited the highest emission rate with a median value of 138 μg m⁻² h⁻¹. The target compounds with median emission rates greater than 20 μg m⁻² h⁻¹ were toluene, 1-propanol, formaldehyde, and 2-butanone. The wood panels/vinyl floor coverings were the largest indoor pollutant source, followed by floorings, wall coverings, adhesives, and paints. The wood panels/vinyl floor coverings contributed nearly three times more to indoor VOC concentrations than paints.     

Industrial wastewater pre-treatment for heavy metal reduction by employing a sorbent-assisted ultrafiltration system

This work examined the adoption of a sorbent-assisted ultrafiltration (UF) system for the reduction of Pb(II), Cu(II), Zn(II) and Ni(II) from industrial wastewater. In such a system metals were removed via several processes which included precipitation through the formation of hydroxides, formation of precipitates/complexes among the metal ions and the wastewater compounds, adsorption of metals onto minerals (bentonite, zeolite, vermiculite) and retention of insoluble metal species by the UF membranes. At pH = 6 the metal removal sequence obtained by the UF system was Pb(II) > Cu(II) > Zn(II) > Ni(II) in mg g⁻¹ with significant amount of lead and copper being removed due to chemical precipitation and formation of precipitates/complexes with wastewater compounds. At this pH, zinc and nickel adsorption onto minerals was significant, particularly when bentonite and vermiculite were employed as adsorbents. Metal adsorption onto zeolite and bentonite followed the sequence Zn(II) > Ni(II) > Cu(II) > Pb(II), while for vermiculite the sequence was Ni(II) > Zn(II) > Cu(II) > Pb(II) in mg g⁻¹. The low amount of Pb(II) and Cu(II) adsorbed by minerals was attributed to the low available lead and copper concentration. At pH = 9 the adoption of UF could effectively reduce heavy metals to very low levels. The same was observed at pH = 8, provided that minerals were added. The prevailing metal removal process was the formation of precipitates/complexes with wastewater compounds.     

Changes in serum concentrations of polychlorinated biphenyls (PCBs), hydroxylated PCB metabolites and pentachlorophenol during pregnancy

We studied pregnancy-related changes in serum concentrations of five polychlorinated biphenyls (PCBs, CB 118, CB 138, CB 153, CB 156, CB 180), three hydroxylated PCB metabolites (4-OH-CB107, 4-OH-CB146, 4-OH-CB187), and pentachlorophenol (PCP). Median serum lipid content increased 2-fold between early (weeks 9-13) and late pregnancy (weeks 35-36) (N = 10), whereas median PCB levels in serum lipids decreased 20-46%, suggesting a dilution of PCB concentrations in serum lipids. Nevertheless, strong positive intra-individual correlations (Spearman’s r = 0.61-0.99) were seen for PCBs during the whole study period. Thus, if samples have been collected within the same relative narrow time window during pregnancy, PCB results from one single sampling occasion can be used in assessment of relative differences in body burdens during the whole pregnancy period. Concentrations of OH-PCBs in blood serum tended to decline as pregnancy progressed, although among some women the concentrations increased at the end of pregnancy. Positive intra-individual correlations (r = 0.66-0.99) between OH-PCB concentrations were observed during the first and second trimester, whereas correlations with third trimester concentrations were more diverging (r = −0.70-0.85). No decline in PCP concentrations was observed during pregnancy and no significant correlations were found between concentrations at different sampling periods. Our results suggest that for both OH-PCBs and PCP, sampling has to be more specifically timed depending on the time period during pregnancy that is of interest. The differences in patterns of intra- and inter-individual variability of the studied compounds may be due to a combination of factors, including lipid solubility, persistence of the compounds, distribution in blood, metabolic formation, and pregnancy-related changes in body composition and physiological processes.     

Linear and non-linear relationships between soil sorption and hydrophobicity: model, validation and influencing factors

The hydrophobic parameter represented by the octanol/water partition coefficient (log P) is commonly used to predict the soil sorption coefficient (K_oc). However, a simple non-linear relationship between log K_oc and log P has not been reported in the literature. In the present paper, soil sorption data for 701 compounds was investigated. The results show that log K_oc is linearly related to log P for compounds with log P in the range of 0.5-7.5 and non-linearly related to log P for the compounds in a wide range of log P. A non-linear model has been developed between log K_oc and log P for a wide range of compounds in the training set. This model was validated in terms of average error (AE), average absolute error (AAE) and root-mean squared error (RMSE) by using an external test set with 107 compounds. Nearly the same predictive capacity was observed in comparison with existing models. However, this non-linear model is simple, and uses only one parameter. The best model developed in this paper is a non-linear model with six correction factors for six specific classes of compounds. This model can well predict log K_oc for 701 diverse compounds with AAE = 0.37. The reasons for systemic deviations in these groups may be attributed to the difference of sorption mechanism for hydrophilic/polar compounds, low solubility for highly hydrophobic compounds, hydrolysis of esters in solution, volatilization for volatile compounds and highly experimental errors for compounds with extremely high or low sorption coefficients.     

Electrochemical oxidation of nitrogen-heterocyclic compounds at boron-doped diamond electrode

Nitrogen-heterocyclic compounds (NHCs) are toxic and bio-refractory contaminants widely spread in environment. This study investigated electrochemical degradation of NHCs at boron-doped diamond (BDD) anode with particular attention to the effect of different number and position of nitrogen atoms in molecular structure. Five classical NHCs with similar structures including indole (ID), quinoline (QL), isoquinoline (IQL), benzotriazole (BT) and benzimidazole (BM) were selected as the target compounds. Results of bulk electrolysis showed that degradation of all NHCs was fit to a pseudo first-order equation. The five compounds were degraded with the following sequence: ID > QL > IQL > BT > BM in terms of their rates of oxidation. Quantum chemical calculation was combined with experimental results to describe the degradation character of NHCs at BDD anode. A linear relationship between degradation rate and delocalization energy was observed, which demonstrated that electronic charge was redistributed through the conjugation system and accumulated at the active sites under the attack of hydroxyl radicals produced at BDD anode. Moreover, atom charge was calculated by semi empirical PM3 method and active sites of NHCs were identified respectively. Analysis of intermediates by GC-MS showed agreement with calculation results.     

Environmental monitoring of complex hydrocarbon mixtures in water and soil samples after solid phase microextraction using PVC/MWCNTs nanocomposite fiber

A novel nanocomposite based on incorporation of multiwalled carbon nanotubes (MWCNTs) in polyvinyl chloride (PVC) was prepared. Proposed nanocomposite was coated on stainless steel wire by deep coating. Composition of nanocomposite was optimized based on results of morphological studies using scanning electron microscopy. The best composition (83% MWCNTs:17% PVC) was applied as a solid phase microextraction fiber. Complex mixture of aromatic (BTEX) and aliphatic hydrocarbons (C₅–C₃₄) were selected as model analytes, and performance of proposed fiber in extraction of the studied compounds from water and soil samples was evaluated. Analytical merits of the method for water samples (LODs = 0.10–1.10 ng L⁻¹, r² = 0.9940–0.9994) and for soil samples (LODs = 0.10–0.77 ng kg⁻¹, r² = 0.9946–0.9994) showed excellent characteristics of it in ultra trace determination of petroleum type environmental pollutants. Finally, the method was used for determination of target analytes in river water, industrial effluent and soil samples.     

Thermodynamic and kinetic study of phenol degradation by a non-catalytic wet air oxidation process

This work is dedicated to an accurate evaluation of thermodynamic and kinetics aspects of phenol degradation using wet air oxidation process. Phenol is a well known polluting molecule and therefore it is important having data of its behaviour during this process. A view cell is used for the experimental study, with an internal volume of 150 mL, able to reach pressures up to 30 MPa and temperatures up to 350 °C. Concerning the thermodynamic phase equilibria, experimental and modelling results are obtained for different binary systems (water/nitrogen, water/air) and ternary system (water/nitrogen/phenol). The best model is the Predictive Soave Redlich Kwong one. This information is necessary to predict the composition of the gas phase during the process. It is also important for an implementation in a process simulation. The second part is dedicated to kinetics evaluation of the degradation of phenol. Different compounds have been detected using GC coupled with a MS. A kinetic scheme is deduced, taking into account the evolution of phenol, hydroquinones, catechol, resorcinol and acetic acid. The kinetic parameters are calculated for this scheme. These data are important to evaluate the evolution of the concentration of the different polluting molecules during the process. A simplified kinetic scheme, which can be easily implemented in a process simulation, is also determined for the direct degradation of phenol into H₂O and CO₂. The Arrhenius law data obtained for the phenol disappearance are the following: k = 1.8 × 10⁶ ± 3.9 × 10⁵ M⁻¹ s⁻¹ (pre-exponential factor) and E_a = 77 ± 8 kJ mol⁻¹ (activation energy).     

Polychlorinated dibenzo-p-dioxin and dibenzofuran in urban air of an Andean city

Particle-bound polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in ambient air were monitored together with particulate matter less than 10 μm (PM₁₀) at three sampling sites of the Andean city of Manizales, Colombia; during September 2009 and July 2010. PCDD/Fs ambient air emissions ranged from 1 fg WHO-TEQ m⁻³ to 52 fg WHO-TEQ m⁻³ in particulate fraction. The PM₁₀ concentrations ranged from 23 μg m⁻³ to 54 μg m⁻³. Concentrations of PM₁₀ and PCDD/Fs in ambient air observed for Manizales - a medium sized city with a population of 380 000 - were comparable to concentrations in larger cities. The highest concentrations of PCDD/Fs and PM₁₀ found in this study were determined at the central zone of the city, characterized by public transportation density, where diesel as principal fuel is used. In addition, hypothetical gas fractions of PCDD/Fs were calculated from theoretical K_p data. Congener profiles of PCDD/Fs exhibited ratios associated with different combustion sources at the different sampling locations, ranging from steel recycling to gasoline and diesel engines. Taking into account particle and gas hypothetical fraction of PCDD/Fs, Manizales exhibited values of PCDD/Fs equivalent to rural and urban-industrial sites in the southeast and center of the city respectively. Poor correlation of PCDDs with PM₁₀ (r = −0.55 and r = 0.52) suggests ambient air PCDDs were derived from various combustion sources. Stronger correlation was observed of PCDFs with PM₁₀. Poor correlation between precipitation and reduced PM₁₀ concentration in ambient air (r = −0.45) suggested low PM₁₀ removal by rainfall.     

Predicting EDC concentrations in a river mixing zone

The fate and transport of endocrine disrupting chemicals (EDCs) in ambient river waters is a major concern associated with effluents from municipal wastewater treatment plants (WWTPs). This paper presents a methodology for quantifying the spatial distribution of EDCs in a river mixing zone. The core of the technical analysis is based on a two-dimensional steady-state analytical model characterized by ambient turbulence in the receiving water. This model was first calibrated with mass transport data from field measurements for a conservative substance (electrical conductivity) and then used to predict aqueous-phase EDC concentrations throughout a WWTP mixing zone. To demonstrate the usefulness of this methodology for water quality management purposes, the modeling framework presented in this paper was used to determine a lumped in-stream attenuation rate constant (k_d = 3 d⁻¹) for 17β-estradiol under natural conditions. This rate constant likely accounts for the combined contributions of physical sorption, photolysis, microbial and chemical degradation, and the measured value is highly consistent with previously published results from bench-scale removal experiments.     

Structure-activity relationships of larvicidal monoterpenes and derivatives against Aedes aegypti Linn

In the search for larvicidal compounds against Aedes aegypti L. (Diptera: Culicidae), a collection of monoterpenes were selected and evaluated. R- and S-limonene exhibited the highest larvicidal potency (LC₅₀ = 27 and 30 ppm, respectively), followed by γ-terpinene (LC₅₀ = 56 ppm) and RS-carvone (LC₅₀ = 118 ppm). Structural characteristics which may contribute to the understanding of the larvicidal activity of monoterpenes were empirically identified. The presence of heteroatoms in the basic hydrocarbon structure decreases larvicidal potency. Conjugated and exo double bonds appear to increase larvicidal potency. Replacement of double bonds by more reactive epoxides decreases the larvicidal potency. The presence of hydroxyls in the cyclic structure resulted in decreased potency, probably due to increased polarity indicanting that lipophilicity seems to play an important role in increasing the larvicidal potency in this set of compounds.     

Polybrominated diphenyl ethers in various atmospheric environments of Taiwan: their levels, source identification and influence of combustion sources

In this study, ambient air samples from different atmospheric environments were examined for both PBDE and PCDD/F characteristics to verify that combustion is a significant PBDE emission source. The mean ± SD atmospheric PBDE concentrations were 165 ± 65.0 pg Nm⁻³ in the heavy steel complex area and 93.9 ± 24.5 pg Nm⁻³ in the metals complex areas, 4.7 and 2.7 times higher than that (35.3 ± 15.5 pg Nm⁻³) in the urban areas, respectively. The statistically high correlation (r = 0.871, p < 0.001) found between the atmospheric PBDE and PCDD/F concentrations reveals that the combustion sources are the most likely PBDE emission sources. Correspondence analysis shows the atmospheric PBDEs of the heavy steel and metals complex areas are associated with BDE-209, -203, -207, -208, indicative of combustion source contributions. Furthermore, the PBDEs in urban ambient air experience the influence of the evaporative releases of the commercial penta- and octa-BDE mixtures, as well as combustion source emissions. By comparing the PBDE homologues of indoor air, urban ambient air, and stack flue gases of combustion sources, we found that the lighter brominated PBDEs in urban ambient air were contributed by the indoor air, while their highly brominated ones were from the combustion sources, such as vehicles. The developed source identification measure can be used to clarify possible PBDE sources not only for Taiwanese atmosphere but also for other environmental media in other countries associated with various emission sources in the future.     

Adsorption of mono- and di-butyltin by a wheat charcoal: pH effects and modeling

Understanding adsorption processes of butyltins (BTs) such as monobutyltin (MBT) and dibutyltin (DBT) by black carbons is important for the evaluation of BT exposure risks to organisms and humans. However, relevant knowledge is scarce. In this study, the acidity constants pK_a,1 = 2.3, pK_a,2 = 3.5 and pK_a,3 = 5.9 for MBT and pK_a,1 = 3.0 and pK_a,2 = 5.1 for DBT are estimated via potentiometric titration. Additionally, adsorption isotherms of BTs to a wheat charcoal were determined. The adsorption behavior was observed to be pH-dependent due to BT speciation and the pH-dependent surface charge of the charcoal. MBT adsorption to the charcoal decreases with increasing pH from 4 to 8, while the highest adsorption occurs at pH 6 for DBT. Adsorption of the BTs is successfully described in the pH range of 3-10 by using a newly developed pH-dependent Dual Langmuir model. The model has the potential to predict the interaction of BT species with charcoal, which can contribute to the risk assessments of BTs in the environment.     

Perfluorooctane sulfonate (PFOS) and other fluorochemicals in fish blood collected near the outfall of wastewater treatment plant (WWTP) in Beijing

Perfluorinated compounds (PFCs) were measured in zooplankton and five fish species collected from Gaobeidian Lake, which receives discharge from wastewater treatment plant (WWTP) in Beijing, China. The mean total PFCs in five fish were in the order: crucian carp > common carp > leather catfish > white semiknife carp > tilapia. Perfluorooctane sulfonate (PFOS) occurred at the greatest concentrations, with mean concentrations ranging from 5.74 to 64.2 ng/ml serum. Perfluorodecanoic acid (PFDA) was the second dominant PFC in fish samples except for common carp in which perfluorooctane sulfonamide (PFOSA) was dominant. A positive linear relationship (r² = 0.85, p < 0.05) was observed between ln PFOS concentrations (ln ng/ml) and trophic level (based on δ¹⁵N) if tilapia was excluded. The risk assessment showed that PFOS might not pose an immediate risk to fish in Gaobeidian Lake.     

Persistent organochlorine pollutants and menstrual cycle characteristics

An evolving body of evidence suggests an adverse relation between persistent organochlorine pollutants (POPs) and menstruation, though prospective longitudinal measurement of menses is limited and served as the impetus for study. We prospectively assessed the relation between a mixture of persistent organochlorine compounds and menstrual cycle length and duration of bleeding in a cohort of women attempting to become pregnant. Eighty-three (83%) women contributing 447 cycles for analysis provided a blood specimen for the quantification of 76 polychlorinated biphenyls and seven organochlorine pesticides, and completed daily diaries on menstruation until a human chorionic gonadotropin confirmed pregnancy or 12 menstrual cycles without conception. Gas chromatography with electron capture detection was used to quantify concentrations (ng g⁻¹ serum); enzymatic methods were used to quantify serum lipids (mg dL⁻¹). A linear regression model with a mixture distribution was used to identify chemicals grouped by purported biologic activity that significantly affected menstrual cycle length and duration of bleeding adjusting for age at menarche and enrollment, body mass index, and cigarette smoking.A significant 3-d increase in cycle length was observed for women in the highest tertile of estrogenic PCB congeners relative to the lowest tertile (β = 3.20; 95% CI 0.36, 6.04). A significant reduction in bleeding (<1 d) was observed among women in the highest versus lowest tertile of aromatic fungicide exposure (γ = −0.15; 95% CI −0.29, −0.00). Select POPs were associated with changes in menstruation underscoring the importance of assessing chemical mixtures for female fecundity.     

Decabromodiphenyl ethane and decabromodiphenyl ether in Swedish background air

Decabromodiphenyl ethane (DPDPE) is a flame retardant that has been on the market for more than 20 years and is used as a replacement for decabromodiphenyl ether (BDE-209). Environmental data on DPDPE are scarce but for BDE-209, studies have shown that long-range transport in the atmosphere leads to contamination of remote regions. Given their similar physical-chemical properties, we hypothesized that this is also true for DPDPE. In this study we explored the European continent as a source for DBDPE by collecting air samples at a back-ground location in southern Sweden. Twelve samples with stable air mass back trajectories over the 24 h sampling period were analysed. BDE-209 and 5 polycyclic aromatic hydrocarbons (PAHs) were also included in the study. The concentration ranges of DBDPE and BDE-209 were similar, 0.077-7.9 and 0.093-1.8 pg m⁻³ air, respectively. The highest concentrations were detected when the air originated from the European continent and the lowest during periods with rather stagnant air over southern Scandinavia. The concentrations of DBDPE and BDE-209 did not co-vary, indicating that there are different major sources of the two compounds. In air, the compounds measured in this study are predominantly associated with particles. PAHs in the atmosphere are known to originate primarily from combustion processes and their concentrations were highly correlated with several measures of atmospheric particle concentration, i.e. PM 10, PM 2.5, soot, and N 450 (number of particles in the size range approximately 420-450 nm). No clear correlations were found between the concentrations of DBDPE or BDE-209 and any of the measures of particle concentrations, indicating that the emissions of these are not related to the major sources of emissions of soot or small particles.     

Association between micronuclei frequency in pollen mother cells of Tradescantia and mortality due to cancer and cardiovascular diseases: A preliminary study in Sao José dos Campos, Brazil

The present study was designed to explore the correlation between the frequency of micronuclei in Trad-MN, measured across 28 biomonitoring stations during the period comprised between 11 of May and 2 of October, 2006, and adjusted mortality rates due to cardiovascular, respiratory diseases and cancer in Sao José dos Campos, Brazil, an area with different sources of air pollution. For controlling purposes, mortality rate due to gastrointestinal diseases (an event less prone to be affected by air pollution) was also considered in the analysis. Spatial distribution of micronuclei frequency was determined using average interpolation. The association between health estimators and micronuclei frequency was determined by measures of Pearson's correlation. Higher frequencies of micronuclei were detected in areas with high traffic and close to a petrochemical pole. Significant associations were detected between micronuclei frequency and adjusted mortality rate due to cardiovascular diseases (r = 0.841, p = 0.036) and cancer (r = 0.890, p = 0.018). The association between mortality due to chronic obstructive pulmonary diseases was positive but did not reach statistical significance (r = 0.640, p = 0.172), probably because of the small number of events. Gastrointestinal mortality did not exhibit significant association with micronuclei frequency. Because the small number of observations and the nature of an ecological study, the present findings must be considered with caution and considered as preliminary. Further studies, performed in different conditions of contamination and climate should be done before considering Trad-MN in the evaluation of human health risk imposed by air pollutants.     

Quality control for sampling of PCDD/PCDF emissions from open combustion sources

Both long duration (>6 h) and high temperature (up to 139 °C) sampling efforts were conducted using ambient air sampling methods to determine if either high volume throughput or higher than ambient air sampling temperatures resulted in loss of target polychlorinated dibenzodioxins/dibenzofurans (PCDDs/PCDFs) from a polyurethane foam (PUF) sorbent. Emissions from open burning of simulated military forward operating base waste were sampled using EPA Method TO-9A for 185 min duration using a filter/PUF/PUF in series combination. After a 54 m³ sample was collected, the sampler was removed from the combustion source and the second PUF was replaced with a fresh, clean PUF. An additional 6 h of ambient air sampling (171 m³) was conducted and the second PUF was analyzed to determine if the PCDD/PCDF transferred from the filter and the first PUF. Less than 4.4% of the initial PCDD/PCDF was lost to the second PUF. To assess the potential for blow off of PCDD/PCDF analytes during open air sampling, the mobility of spiked mono- to hepta-PCDD/PCDF standards across a PUF sorbent was evaluated from ambient air temperatures to 145 °C with total volumes between 600 L and 2400 L. Lower molecular weight compounds and higher flow amounts increased release of the spiked standards consistent with vapor pressure values. At 600 L total sampled volume, the release temperature for 1% of the tetra-CDD (the lowest chlorinated homologue with a toxic compound) was 87 °C; increasing the volume fourfold reduced this temperature to 73 °C.     

Developing slow-release persulfate candles to treat BTEX contaminated groundwater

The development of slow-release chemical oxidants for sub-surface remediation is a relatively new technology. Our objective was to develop slow-release persulfate-paraffin candles to treat BTEX-contaminated groundwater. Laboratory-scale candles were prepared by heating and mixing Na₂S₂O₈ with paraffin in a 2.25 to 1 ratio (w/w), and then pouring the heated mixture into circular molds that were 2.38 cm long and either 0.71 or 1.27 cm in diameter. Activator candles were prepared with FeSO₄ or zerovalent iron (ZVI) and wax. By treating benzoic acid and BTEX compounds with slow-release persulfate and ZVI candles, we observed rapid transformation of all contaminants. By using ¹⁴C-labeled benzoic acid and benzene, we also confirmed mineralization (conversion to CO2) upon exposure to the candles. As the candles aged and were repeatedly exposed to fresh solutions, contaminant transformation rates slowed and removal rates became more linear (zero-order); this change in transformation kinetics mimicked the observed dissolution rates of the candles. By stacking persulfate and ZVI candles on top of each other in a saturated sand tank (14 × 14 × 2.5 cm) and spatially sampling around the candles with time, the dissolution patterns of the candles and zone of influence were determined. Results showed that as the candles dissolved and persulfate and iron diffused out into the sand matrix, benzoic acid or benzene concentrations (C_o = 1 mM) decreased by >90% within 7 d. These results support the use of slow-release persulfate and ZVI candles as a means of treating BTEX compounds in contaminated groundwater.