A new rate index for environmental monitoring of combined reuse/recycle packaging systems.

It is shown that the conventional recycling rate fails to reflect environmental performance for packaging flows with both recycle and reuse. The reuse rate, the total number of reuse trips and the reuse- lifetime are also shown to be inadequate. A new rate index defined in terms of the total amount of packaging material reaching the consumer is proposed. It reflects immediate improvements in environmental impact according to specific criteria and it reduces to the conventional rate for systems with only recycle. Albeit this shortcut environmental assessment is not entirely comprehensive and does not unveil a full sustainability profile, it may be useful for immediate packaging flow evaluation and policy implementation. For given packaging production technology it reveals a specific maximum level on recycling, below which environmental impacts from processing are limited or reduced, even if production level grows. Cleaner technologies in reprocessing of recycled materials may elevate this maximum level while still limiting or reducing environmental impacts.     

Waste collection systems for recyclables: An environmental and economic assessment for the municipality of Aarhus (Denmark)

Recycling of paper and glass from household waste is an integrated part of waste management in Denmark, however, increased recycling is a legislative target. The questions are: how much more can the recycling rate be increased through improvements of collection schemes when organisational and technical limitations are respected, and what will the environmental and economic consequences be? This was investigated in a case study of a municipal waste management system. Five scenarios with alternative collection systems for recyclables (paper, glass, metal and plastic packaging) were assessed by means of a life cycle assessment and an assessment of the municipality’s costs. Kerbside collection would provide the highest recycling rate, 31% compared to 25% in the baseline scenario, but bring schemes with drop-off containers would also be a reasonable solution. Collection of recyclables at recycling centres was not recommendable because the recycling rate would decrease to 20%. In general, the results showed that enhancing recycling and avoiding incineration was recommendable because the environmental performance was improved in several impact categories. The municipal costs for collection and treatment of waste were reduced with increasing recycling, mainly because the high cost for incineration was avoided. However, solutions for mitigation of air pollution caused by increased collection and transport should be sought.     

Chemical depolymerisation of PET complex waste: hydrolysis vs. glycolysis

The huge increase in the generation of post-consumer plastic waste has produced a growing interest in eco-efficient strategies and technologies for their appropriate management and recycling. In response to this, PROQUIPOL Project is focused on developing, optimizing and adapting feedstock recycling technologies as an alternative for management for the treatment of complex plastic waste. Among the different plastic wastes studied, PROQUIPOL Project is working on providing a suitable treatment to the highly colored and complex multilayered post-consumer waste fractions of polyethylene terephthalate (PET) by chemical depolymerisation methods. Glycolysis and alkali hydrolysis processes have been studied with the aim of promoting the transformation of PET into the bis(2-hydroxyethyl) terephthalate monomer and terephthalic acid, respectively. In both cases operational conditions such as temperature, reaction time, catalyst to PET rate and solvent to PET rate have been considered to optimize product yield, achieving values near to 90 % and monomer purities over 95 % in both processes. This paper presents results obtained for each treatment as well as a simplified comparison of technical, economic and environmental issues.     

Influence of RFID tags on recyclability of plastic packaging

The use of Radio Frequency IDentification Technology (RFID) in the packaging sector is an important logistical improvement regarding the advantages offered by this technology in comparison with barcodes. Nevertheless, the presence of these devices in plastic packaging, and consequently in plastic waste, can cause several problems in the recycling plants due to the materials included in these devices.In this study, the mentioned recycling constraints have been experimentally identified in a pilot scale recycling study consisting in three recycling tests with an increasing presence of RFID tags. Differences in each test were evaluated. Furthermore, the quality of the recycled material of each test was studied through the injection and testing of tests probes.The results of the pilot scale recycling tests did not show a decrease in the quality of the recycled plastic due to the presence of RFID tags. Nevertheless, several operational problems during the recycling process were observed such as the obstruction of the screens, which lessened the process yield and created process interruptions, as well as the loss of extruded plastic during the process.These recycling constraints cannot be directly extrapolated to the industrial plants due to the different working scales. Nevertheless, technological solutions are proposed in order to avoid these recycling constraints if they appear.     

Cryo-comminution of plastic waste

Recycling of plastics is a big issue in terms of environmental sustainability and of waste management. The development of proper technologies for plastic recycling is recognised as a priority. To achieve this aim, the technologies applied in mineral processing can be adapted to recycling systems. In particular, the improvement of comminution technologies is one of the main actions to improve the quality of recycled plastics. The aim of this work is to point out suitable comminution processes for different types of plastic waste. Laboratory comminution tests have been carried out under different conditions of temperature and sample pre-conditioning adopting as refrigerant agents CO2 and liquid nitrogen. The temperature has been monitored by thermocouples placed in the milling chamber. Also different internal mill screens have been adopted. A proper procedure has been set up in order to obtain a selective comminution and a size reduction suitable for further separation treatment. Tests have been performed on plastics coming from medical plastic waste and from a plant for spent lead batteries recycling. Results coming from different mill devices have been compared taking into consideration different indexes for representative size distributions. The results of the performed tests show as cryo-comminution improves the effectiveness of size reduction of plastics, promotes liberation of constituents and increases specific surface size of comminuted particles in comparison to a comminution process carried out at room temperature.     

Recycling and recovery routes of plastic solid waste (PSW): A review

Plastic solid waste (PSW) presents challenges and opportunities to societies regardless of their sustainability awareness and technological advances. In this paper, recent progress in the recycling and recovery of PSW is reviewed. A special emphasis is paid on waste generated from polyolefinic sources, which makes up a great percentage of our daily single-life cycle plastic products. The four routes of PSW treatment are detailed and discussed covering primary (re-extrusion), secondary (mechanical), tertiary (chemical) and quaternary (energy recovery) schemes and technologies. Primary recycling, which involves the re-introduction of clean scrap of single polymer to the extrusion cycle in order to produce products of the similar material, is commonly applied in the processing line itself but rarely applied among recyclers, as recycling materials rarely possess the required quality. The various waste products, consisting of either end-of-life or production (scrap) waste, are the feedstock of secondary techniques, thereby generally reduced in size to a more desirable shape and form, such as pellets, flakes or powders, depending on the source, shape and usability. Tertiary treatment schemes have contributed greatly to the recycling status of PSW in recent years. Advanced thermo-chemical treatment methods cover a wide range of technologies and produce either fuels or petrochemical feedstock. Nowadays, non-catalytic thermal cracking (thermolysis) is receiving renewed attention, due to the fact of added value on a crude oil barrel and its very valuable yielded products. But a fact remains that advanced thermo-chemical recycling of PSW (namely polyolefins) still lacks the proper design and kinetic background to target certain desired products and/or chemicals. Energy recovery was found to be an attainable solution to PSW in general and municipal solid waste (MSW) in particular. The amount of energy produced in kilns and reactors applied in this route is sufficiently investigated up to the point of operation, but not in terms of integration with either petrochemical or converting plants. Although primary and secondary recycling schemes are well established and widely applied, it is concluded that many of the PSW tertiary and quaternary treatment schemes appear to be robust and worthy of additional investigation.     

Evaluation of recycling policies for PET bottles based on multiattribute utility indices

This study focused on waste plastic, especially the polyethylene telephthalate (PET) bottle as representative waste, which has been assigned as goods to be recycled by the Packaging Waste Recycling Law in Japan. We developed a plastic transport model which explained the entire flow of plastic from the production stage to the disposal stage within an the evaluation model of plastic recycle policy based on multiattribute utility theory. This model is designed to be used by local municipal governments in supporting the evaluation of the PET bottle recycling policy. In evaluating the plastics recycling policy, we selected indices relating to economy, ecology, and rate of resource recycling. The results indicate that when the evaluation of the material recycling policy and thermal recycling policy in the model city were characterized in terms of their economic and environmental aspects the thermal recycling policy had the highest utility within our scenario. Received: July 31, 1998 / Accepted: January 26, 1999     

Physical Characterization and Pre-assessment of Recycled High-Density Polyethylene as 3D Printing Material

3D printing has received lots of attention due to its limitless potential and advantages in comparison to traditional manufacturing processes. This study focuses on the most popular type of home 3D printers, namely fused filament fabrication (FFF) printers, which use plastic filaments as the feedstock. The rather high material cost and large amount of plastic waste generated by FFF 3D printers have driven the need for plastic filaments produced from recycled plastic waste. This study evaluates, in terms of physical characterization, the feasibility of using recycled high-density polyethylene (HDPE), one of the most commonly used plastics, as the feedstock for 3D printers, in comparison with the common acrylonitrile butadiene styrene plastic pellets. In-house extrusion using recycled HDPE pellets and flakes is possible. The diameter consistency and extrusion rate results, along with other physical characterization results, including differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared spectroscopy, Raman spectroscopy, and water absorption, suggest that making filaments from recycled HDPE pellets is a viable option, as the obtained filament has favorable water rejection and comparable extrusion rate and thermal stability. Existing methods for overcoming the warping and adhesion problems in 3D printing with HDPE were also reviewed. In order to increase the market competitiveness of waste-derived filaments, optimization of the extrusion process, studies on the mechanical and aging properties, and development of a standard characterization methodology and database are crucial.     

Waste battery treatment options: Comparing their environmental performance

Waste consumer batteries are recycled using different routes based on hydrometallurgical and pyrometallurgical processes. Two hydrometallurgical and two pyrometallurgical treatment scenarios are compared starting from an average composition of Belgian waste batteries. The environmental performance is compared using life cycle analysis (LCA). The recycling rate is studied through mass balance calculation.Each treatment scenario results in a specific recycling rate. The environmental impact and benefits also vary between the treatment options. There is no such thing as a typical hydrometallurgical or pyrometallurgical treatment. When applying a hydrometallurgical treatment scenario, the focus lies on zinc and iron recycling. When allowing manganese recycling, the energy demand of the hydrometallurgical process increases considerably. Both pyrometallurgical options recycle zinc, iron and manganese. According to the LCA, none of the treatment scenarios performs generally better or worse than the others. Each option has specific advantages and disadvantages. The Batteries Directive 2006/66/EC sets out a recycling rate of 50% for consumer waste batteries. Based on metal recycling alone, the mass balances show that the target is difficult to obtain.     

A simple model for complex waste recycling scenarios in developing economies

Future uncertainties involved in the current waste management activities in the developing nations have been addressed through determining plastic waste recovery, recycling and landfilling scenarios in two case study countries — Bangladesh and India. In order to discern and comprehend the material in-flow and out-flow of such complex successive plastics recoveries and recyclings, within the closed-loop recycling systems present in these two countries, a simple mathematical model is developed. The model is based on limited published information, on extensive fieldwork in Dhaka, Calcutta and Delhi, and on experimental data. An environmental legislative factor has been included in the model which will allow balancing of the quality of recycled products and the amount of landfilling non-recyclable plastics. The model has the potential to create and predict a sound waste database for these countries. Bangladesh has been chosen as a model developing country for this study. The mathematical model can be used in future decision making processes within the plastics recycling arena of the countries concerned to achieve an environmentally sound and cost effective waste management option.     

Use of recycling stations in Borlänge, Sweden--volume weights and attitudes

This paper presents a study of recycling stations in the municipality of Borl?nge, Sweden. The main objectives were to measure volume weights of recyclables, to facilitate future planning of collection intervals and bin/container volume, and to investigate the general attitudes among the public towards waste management in general and recycling stations in particular. Volume weights measured in bins/containers were: paper/newsprint: 297 kg/m3, glass packaging: 297 kg/m3, metal packaging: 81.7 kg/m3, paper packaging: 27.8 kg/m3, plastic packaging: 28.1 kg/m3. The recycling stations have been in use since 1994. Most visitors (90%) arrived by car but said the visit to the recycling station was not the main purpose of the trip. The results from the interviews indicated that the people who use the recycling stations have found ways to incorporate waste sorting into their everyday lives, with the help of information, design of the collection system and environmental concerns.     

Estimation of residual MSW heating value as a function of waste component recycling

Recycling of packaging wastes may be compatible with incineration within integrated waste management systems. To study this, a mathematical model is presented to calculate the fraction composition of residual municipal solid waste (MSW) only as a function of the MSW fraction composition at source and recycling fractions of the different waste materials. The application of the model to the Lisbon region yielded results showing that the residual waste fraction composition depends both on the packaging wastes fraction at source and on the ratio between that fraction and the fraction of the same material, packaging and non-packaging, at source. This behaviour determines the variation of the residual waste LHV. For 100% of paper packaging recycling, LHV reduces 4.2% whereas this reduction is of 14.4% for 100% of packaging plastics recycling. For 100% of food waste recovery, LHV increases 36.8% due to the moisture fraction reduction of the residual waste. Additionally the results evidence that the negative impact of recycling paper and plastic packaging on the LHV may be compensated by recycling food waste and glass and metal packaging. This makes packaging materials recycling and food waste recovery compatible strategies with incineration within integrated waste management systems.     

Processes in informal end-processing of e-waste generated from personal computers in Vietnam

Informal treatment of e-waste plays an important role in many countries which have no or weak formal waste management structures. One of the challenges for assessing informal e-waste recycling technologies is to identify their disadvantages and potential technology improvement. The analysis of informal recycling processes starts with a balance of input and output materials for each of the processes. Main obstacles are the fact that in most cases, mixed or variety materials serve as input and, secondly by nature, the informal sector does not systematically measure and monitor the process. This study presents the processes and available data for informal e-waste recycling of desktop personal computer as it consists of components made of plastic and many metals within the Vietnamese context. To identify the most relevant processes, critical flows and technology gap, two scenarios are compared: (1) current situation in which recycling activities are taken in recycling craft villages and (2) appropriately selected BAT. The selected materials from e-waste cover a wide range of recycling processes and technologies: Printed Circuit Board treatment, metal (ferrous metal, aluminum and copper) and plastic recycling.

     

Recycling of plastic packaging waste in Bandung City,Indonesia

Economic growth, changing consumption and production patterns are resulting in rapid increase in the generation of plastic wastes, including plastic packaging waste (PPW). A variety of PPW is identified in the municipal solid waste (MSW) stream. In this paper, quantity and composition of PPW at generators (residential and nonresidential sectors) and at the informal sector of waste recycling were measured, and accordingly the flow of PPW within Bandung City, Indonesia was analyzed. Though the generation rate per capita is not so high (25.1 g per day), total PPW generated by 2.3 million inhabitants in Bandung becomes 58.4 tonnes per day (3.76 % of total MSW generated). Due to lack of integrated MSW management, most of PPW is neither collected properly nor disposed of in appropriate manner by the municipality. Collection of valuable wastes including PPW is done predominantly by the informal sector without regard to health and safety. It is predicted that total PPW recycled by various informal waste recycling players like scavengers, junkmen, intermediates, and dealers is 27.5 tonnes per day (64.6 % of total PPW generated). Interviews regarding the existing handling methods and incentives preferred by generators to increase the recycling rate are also presented.     

Recovery of PET from packaging plastics mixtures by wet shaking table

Recycling requires the separation of materials appearing in a mass of wastes of heterogeneous composition and characteristics, into single, almost pure, component/material flows. The separation of materials (e.g., some types of plastics) with similar physical properties (e.g., specific gravity) is often accomplished by human sorting. This is the case of the separation of packaging plastics in municipal solid wastes (MSW). The low cost of virgin plastics and low value of recycled plastics necessitate the utilization of low cost techniques and processes in the recycling of packaging plastics. An experimental study was conducted to evaluate the feasibility of production of a PET product, cleaned from PVC and PS, using a wet shaking table. The wet shaking table is an environmentally friendly process, widely used to separate minerals, which has low capital and operational costs. Some operational variables of the equipment, as well as different feed characteristics, were considered. The results show that the separation of these plastics is feasible although, similarly to the mineral field, in somewhat complex flow sheets.     

Life cycle assessment of a packaging waste recycling system in Portugal

Life Cycle Assessment (LCA) has been used to assess the environmental impacts associated with an activity or product life cycle. It has also been applied to assess the environmental performance related to waste management activities. This study analyses the packaging waste management system of a local public authority in Portugal. The operations of selective and refuse collection, sorting, recycling, landfilling and incineration of packaging waste were considered. The packaging waste management system in operation in 2010, which we called “Baseline” scenario, was compared with two hypothetical scenarios where all the packaging waste that was selectively collected in 2010 would undergo the refuse collection system and would be sent directly to incineration (called “Incineration” scenario) or to landfill (“Landfill” scenario). Overall, the results show that the “Baseline” scenario is more environmentally sound than the hypothetical scenarios.     

Molecular Modification and Compatibilization of Collected Polyethylene

The increasing use of plastics in packaging materials leads to growing amounts of plastic waste. Recycling material is generally regarded as advantageous. But in fact very few products are made from plastic waste, partly this can be explained by that little is known about the recycling process and the properties of collected materials. There is a need for injection moulding grades of recycled polyethylene, while large amounts of extrusion grades are available from packaging waste. A controlled way of de-branching or partly degrading PE would be desirable. Peroxides are commonly used to crosslink polyolefins, but under certain conditions a chain scission reaction occur. Another problem encountered with recycling of polyethylene are the poor miscibility of low amounts contaminations, i. e. polypropylene. A compatibilizer can improve properties of such polymer blends, in this work EPDM is used as compatibilzer. Studies of mechanical properties and viscosity measurements show that it is possible to partly degrade PE with peroxide exposing it to high temperature and oxygen. The properties of PE/PP blends were improved with EPDM as compatibilizer.     

Flammability Properties of Virgin and Recycled Polycarbonate (PC) and Acrylonitrile–Butadiene–Styrene (ABS) Recovered from End-of-Life Electronics

Acrylonitrile–Butadiene–Styrene (ABS), Polycarbonate (PC) and their alloys are widely used in automotive industry, computer and equipment housings. With increasing disposal of end-of-life electronic equipment, there is also an increased demand for recycling of these materials so that they do not pose environmental challenge as solid waste. One of the recycling approaches is mechanical recycling of these thermoplastics where recycled plastic is melt blended with virgin materials to obtain a high quality product. Besides obtaining desirable mechanical properties, such blends should also conform to fire safety standards. In this work, a series of blends were prepared using PC and ABS recovered from discarded computers and virgin materials using a twin-screw extruder. Their flammability properties were evaluated using burner flammability tests and Ohio State University (OSU) release rate tests. It was found that the extinguishing time, burning extent and weight loss appears to progressively decrease with the addition of both virgin or recycled PC to virgin or recycled ABS. It was also seen that the addition of the 70% of PC, virgin or recycled, to ABS virgin or recycled, appears to significantly decrease heat release and smoke evolution. The results of this study indicate that recycled polycarbonate can be used as an additive for virgin or recycled ABS, as a means of giving flame resistance to ABS in high-value applications. This result is significant when related to the result obtained by a separate study indicating that up to 25% of recycled material can be used without degradation of mechanical properties in the presence of 15% short glass fiber reinforcement.     

Solid industrial wastes and their management in Asegra (Granada, Spain)

ASEGRA is an industrial area in Granada (Spain) with important waste management problems. In order to properly manage and control waste production in industry, one must know the quantity, type, and composition of industrial wastes, as well as the management practices of the companies involved. In our study, questionnaires were used to collect data regarding methods of waste management used in 170 of the 230 businesses in the area of study. The majority of these companies in ASEGRA are small or medium-size, and belong to the service sector, transport, and distribution. This was naturally a conditioning factor in both the type and management of the wastes generated. It was observed that paper and cardboard, plastic, wood, and metals were the most common types of waste, mainly generated from packaging (49% of the total volume), as well as material used in containers and for wrapping products. Serious problems were observed in the management of these wastes. In most cases they were disposed of by dumping, and very rarely did businesses resort to reuse, recycling or valorization. Smaller companies encountered greater difficulties when it came to effective waste management. The most frequent solution for the disposal of wastes in the area was dumping.