Oxidative remobilization of biogenic uranium(IV) precipitates: effects of iron(II) and pH

The oxidative remobilization of uranium from biogenic U(IV) precipitates was investigated in bioreduced sediment suspensions in contact with atmospheric O2 with an emphasis on the influence of Fe(II) and pH on the rate and extent of U release from the solid to the aqueous phase. The sediment was collected from the U.S. Department of Energy Field Research Center (FRC) site at Oak Ridge, Tennessee. Biogenic U(IV) precipitates and bioreduced sediment were generated through anaerobic incubation with a dissimilatory metal reducing bacterium Shewanella putrefaciens strain CN32. The oxidative remobilization of freshly prepared and 1-yr aged biogenic U(IV) was conducted in 0.1 mol/L NaNO3 electrolyte with variable pH and Fe(II) concentrations. Biogenic U(IV)O2(s) was released into the aqueous phase with the highest rate and extent at pH 4 and 9, while the U remobilization was the lowest at circumneutral pH. Increasing Fe(II) significantly decreased U remobilization to the aqueous phase. From 70 to 100% of the U in the sediments used in all the tests was extractable at the experiment termination (41 d) with a bicarbonate solution (0.2 mol/L), indicating that biogenic U(IV) was oxidized regardless of Fe(II) concentration and pH. Sorption experiments and modeling calculations indicated that the inhibitive effect of Fe(II) on U(IV) oxidative remobilization was consistent with the Fe(III) oxide precipitation and U(VI) sorption to this secondary phase.     

Equilibrium and kinetic studies on biosorption of Hg(II), Cd(II) and Pb(II) ions onto microalgae Chlamydomonas reinhardtii

The microalgae Chlamydomonas reinhardtii was used for the biosorption of Hg(II), Cd(II) and Pb(II) ions. The maximum adsorption of Hg(II) and Cd(II) ions on Chlamydomonas reinhardtii biomass was observed at pH 6.0 and the corresponding value for Pb(II) ions was 5.0. The biosorption of Hg(II), Cd(II) and Pb(II) ions by microalgae biomass increased as the initial concentration of Hg(II), Cd(II) and Pb(II) ions increased in the biosorption medium. The maximum biosorption capacities of microalgae for Hg(II), Cd(II) and Pb(II) ions were 72.2+/-0.67, 42.6+/-0.54 and 96.3+/-0.86 mg/g dry biomass, respectively. The affinity order for algal biomass was Pb(II)>Hg(II)>Cd(II). FT-IR analysis of algal biomass revealed the presence of amino, carboxyl, hydroxyl and carbonyl groups, which were responsible for biosorption of metal ions. Biosorption equilibrium was established in about 60 min and the equilibrium was well described by the Freundlich biosorption isotherms. Temperature change in the range of 5-35 degrees C did not affect the biosorption capacity. The microalgae could be regenerated using 0.1 M HCl, with up to 98% recovery, which allowed the reuse of the biomass in six biosorption-desorption cycles without any considerable loss of biosorption capacity.     

Adsorptive removal of Cd(II) and Pb(II) ions from aqueous solutions by using Turkish illitic clay

The ability of Turkish illitic clay (TIC) in removal of Cd(II) and Pb(II) ions from aqueous solutions has been examined in a batch adsorption process with respect to several experimental conditions including initial solution pH, contact time, initial metal ions concentration, temperature, ionic strength, and TIC concentration, etc. The characterization of TIC was performed by using FTIR, XRD and XRF techniques. The maximum uptake of Cd(II) (11.25 mg g⁻¹) and Pb(II) (238.98 mg g⁻¹) was observed when used 1.0 g L⁻¹ of TIC suspension, 50 mg L⁻¹ of initial Cd(II) and 250 mg L⁻¹ of initial Pb(II) concentration at initial pH 4.0 and contact time of 240 min at room temperature. The experimental data were analyzed by the Langmuir, Freundlich, Temkin and Dubinin Radushkevich (D-R) isotherm models. The monolayer adsorption capacity of TIC was found to be 13.09 mg g⁻¹ and 53.76 mg g⁻¹ for Cd(II) and Pb(II) ions, respectively. The kinetics of the adsorption was tested using pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The results showed that the adsorption of Cd(II) and Pb(II) ions onto TIC proceeds according to the pseudo-second-order model. Thermodynamic parameters including the Gibbs free energy (ΔG), enthalpy (ΔH), and entropy (ΔS) changes indicated that the present adsorption process was feasible, spontaneous and endothermic in the temperature range of 5–40 °C.     

Adsorption characterization of Pb(II) and Cu(II) ions onto chitosan-tripolyphosphate beads: Kinetic,equilibrium and thermodynamic studies

Chitosan-tripolyphosphate (CTPP) beads were synthesized, characterized and were used for the adsorption of Pb(II) and Cu(II) ions from aqueous solution. The effects of initial pH, agitation period, adsorbent dosage, different initial concentrations of heavy metal ions and temperature were studied. The experimental data were correlated with the Langmuir, Freundlich and Dubinin-Radushkevich isotherm models. The maximum adsorption capacities of Pb(II) and Cu(II) ions in a single metal system based on the Langmuir isotherm model were 57.33 and 26.06 mg/g, respectively. However, the beads showed higher selectivity towards Cu(II) over Pb(II) ions in the binary metal system. Various thermodynamic parameters such as enthalpy (ΔH°), Gibbs free energy (ΔG°) and entropy (ΔS°) changes were computed and the results showed that the adsorption of both heavy metal ions onto CTPP beads was spontaneous and endothermic in nature. The kinetic data were evaluated based on the pseudo-first and -second order kinetic and intraparticle diffusion models. Infrared spectra were used to elucidate the mechanism of Pb(II) and Cu(II) ions adsorption onto CTPP beads.     

Removal of Fe(II) from the wastewater of a galvanized pipe manufacturing industry by adsorption onto bentonite clay

Bentonite clay has been used for the adsorption of Fe(II) from aqueous solutions over a concentration range of 80-200 mg/l, shaking time of 1-60 min, adsorbent dosage from 0.02 to 2 g and pH of 3. The process of uptake follows both the Langmuir and Freundlich isotherm models and also the first-order kinetics. The maximum removal (>98%) was observed at pH of 3 with initial concentration of 100 mg/l and 0.5 g of bentonite. The efficiency of Fe(II) removal was also tested using wastewater from a galvanized pipe manufacturing industry. More than 90% of Fe(II) can be effectively removed from the wastewater by using 2.0 g of the bentonite. The effect of cations (i.e. zinc, manganese, lead, cadmium, nickel, cobalt, chromium and copper) on the removal of Fe(II) was studied in the concentration range of 10-500 mg/l. All the added cations reduced the adsorption of Fe(II) at high concentrations except Zn. Column studies have also been carried out using a certain concentration of wastewater. More than 99% recovery has been achieved by using 5 g of the bentonite with 3M nitric acid solution.     

Adsorption of Cu(II) ions from aqueous solutions on biochars prepared from agricultural by-products

In this study, the adsorption of Cu(II) from aqueous solutions by agricultural by-products, such as rice husks, olive pomace and orange waste, as well as compost, was evaluated. The aim was to obtain sorbent materials (biochars) through hydrothermal treatment (300?°C) and pyrolysis (300?°C and 600?°C). The effect of adsorbent dose, pH, contact time and initial Cu(II) concentration in batch-mode experiments was investigated. The optimum Cu(II) adsorption conditions was found to occur at 5-12?g/L adsorbent dose, initial pH 5-6, and reaction time 2-4?h. Furthermore, the adsorption kinetics were best described by the pseudo-second order model for all the tested materials, while the adsorption equilibrium best fitted by the linear and Freundlich isotherms. Comparing rice husks and olive pomace, the higher adsorption capacity resulted after pyrolysis at 300?°C. With respect to the orange waste and compost, the highest adsorption capacity was observed using biochars obtained after hydrothermal treatment and pyrolysis at 300?°C.     

Immobilization of Pb(II), Cd(II) and Ni(II) ions on kaolinite and montmorillonite surfaces from aqueous medium

The present study investigates the immobilization of Pb(II), Cd(II) and Ni(II) on clays (kaolinite and montmorillonite) in aqueous medium through the process of adsorption under a set of variables (concentration of metal ion, amount of clay, pH, time and temperature of interaction). Increasing pH favours the removal of metal ions till they are precipitated as the insoluble hydroxides. The uptake is rapid with maximum adsorption being observed within 180 min for Pb(II) and Ni(II) and 240 min for Cd(II). A number of available models like the Lagergren pseudo first-order kinetics, second-order kinetics, Elovich equation, liquid film diffusion and intra-particle diffusion are utilized to evaluate the kinetics and the mechanism of the immobilization interactions. Two isotherm equations due to Langmuir and Freundlich showed good fits with the experimental data. Kaolinite and montmorillonite have considerable Langmuir monolayer capacity with respect to Pb(II), Cd(II) and Ni(II), the values being in the range of 6.8-11.5mg/g (kaolinite) and 21.1-31.1mg/g (montmorillonite). The Freundlich adsorption capacity follows a similar order. The thermodynamics of the immobilization process indicates the same to be exothermic with Pb(II) and Ni(II), but endothermic with Cd(II). The interactions with Pb(II) and Ni(II) are accompanied by decrease in entropy and Gibbs energy while the endothermic immobilization of Cd(II) is supported by an increase in entropy and an appreciable decrease in Gibbs energy. The results have established good potentiality for kaolinite and montmorillonite to remove heavy metals like Pb(II), Cd(II) and Ni(II) from aqueous medium through adsorption-mediated immobilization.     

Biosorption of Cu(II), Zn(II), Ni(II) and Pb(II) ions by cross-linked metal-imprinted chitosans with epichlorohydrin

Cross-linked metal-imprinted chitosan microparticles were prepared from chitosan, using four metals (Cu(II), Zn(II), Ni(II), and Pb(II)) as templates, and epichlorohydrin as the cross-linker. The microparticles were characterized by Fourier transform infrared spectroscopy, solid state (13)C nuclear magnetic resonance spectroscopy, and energy-dispersive X-ray spectroscopy. They were used for comparative biosorption of Cu(II), Zn(II), Ni(II) and Pb(II) ions in an aqueous solution. The results showed that the sorption capacities of Cu(II), Zn(II), Ni(II), and Pb(II) on the templated microparticles increased from 25 to 74%, 13 to 46%, 41 to 57%, and 12 to 43%, respectively, as compared to the microparticles without metal ion templates. The dynamic study showed that the sorption process followed the second-order kinetic equation. Three sorption models, Langmuir, Freundlich, and Dubinin-Radushkevich, were applied to the equilibrium isotherm data. The result showed that the Langmuir isotherm equation best fitted for monolayer sorption processes. Furthermore, the microparticles can be regenerated and reused for the metal removal.     

Removal of copper (II) from aqueous solution by adsorption onto low-cost adsorbents

The use of low-cost adsorbents was investigated as a replacement for current costly methods of removing metals from aqueous solution. Removal of copper (II) from aqueous solution by different adsorbents such as shells of lentil (LS), wheat (WS), and rice (RS) was investigated. The equilibrium adsorption level was determined as a function of the solution pH, temperature, contact time, initial adsorbate concentration and adsorbent doses. Adsorption isotherms of Cu (II) on adsorbents were determined and correlated with common isotherm equations such as Langmuir and Freundlich models. The maximum adsorption capacities for Cu (II) on LS, WS and RS adsorbents at 293, 313 and 333 K temperature were found to be 8.977, 9.510, and 9.588; 7.391, 16.077, and 17.422; 1.854, 2.314, and 2.954 mg g(-1), respectively. The thermodynamic parameters such as free energy (delta G0), enthalpy (delta H0) and entropy changes (delta S0) for the adsorption of Cu (II) were computed to predict the nature of adsorption process. The kinetics and the factors controlling the adsorption process were also studied. Locally available adsorbents were found to be low-cost and promising for the removal of Cu (II) from aqueous solution.     

Effects of oxide coating and selected cations on nitrate reduction by iron metal

Under anoxic conditions, zerovalent iron (Fe(0)) reduces nitrate to ammonium and magnetite (Fe3O4) is produced at near-neutral pH. Nitrate removal was most rapid at low pH (2-4); however, the formation of a black oxide film at pH 5 to 8 temporarily halted or slowed the reaction unless the system was augmented with Fe(2+), Cu(2+), or Al(3+). Bathing the corroding Fe(0) in a Fe(2+) solution greatly enhanced nitrate reduction at near-neutral pH and coincided with the formation of a black precipitate. X-ray diffractometry and scanning electron microscopy confirmed that both the black precipitate and black oxide coating on the iron surface were magnetite. In this system, ferrous iron was determined to be a partial contributor to nitrate removal, but nitrate reduction was not observed in the absence of Fe(0). Nitrate removal was also enhanced by augmenting the Fe(0)-H2O system with Fe(3+), Cu(2+), or Al(3+) but not Ca(2+), Mg(2+), or Zn(2+). Our research indicates that a magnetite coating is not a hindrance to nitrate reduction by Fe(0), provided sufficient aqueous Fe(2+) is present in the system.     

Screening of factors influencing Cu(II) extraction by soybean oil-based organic solvents using fractional factorial design

This study aimed to identify the significant factors that give large effects on the efficiency of Cu(II) extraction from aqueous solutions by soybean oil-based organic solvents using fractional factorial design. Six factors (mixing time (t), di-2-ethylhexylphosphoric acid concentration ([D2EHPA]), organic to aqueous phase ratio (O:A), sodium sulfate concentration ([Na(2)SO(4)]), equilibrium pH (pH(eq)) and tributylphosphate concentration ([TBP])) affecting the percentage extraction (%E) of Cu(II) were investigated. A 2(6-1) fractional factorial design was applied and the results were analyzed statistically. The results show that only [D2EHPA], pH(eq) and their second-order interaction ([D2EHPA] × pH(eq)) influenced the %E significantly. Regression models for %E were developed and the adequacy of the reduced model was examined. The results of this study indicate that fractional factorial design is a useful tool for screening a large number of variables and reducing the number of experiments.     

Mobilization of trace metals and inorganic compounds during resuspension of anoxic sediments from Trepangier Bayou, Louisiana

The release of trace metals (Mn, Ni, Co, Cu, Zn, Pb, and Cd) and inorganic compounds (As) from initially anoxic Trepangier Bayou sediments, Louisiana and the sources of the released metals were investigated. After 1 to 2 d aeration, significant amounts of trace metals (Mn, Zn, Cd, Ni, and Co) were released to the aqueous phase with increased acidity, primarily due to the oxidation of acid-volatile sulfide and ferrous iron and iron sulfide minerals. The addition of a bacterial inhibitor, NaN,, to the Trepangier sediment during resuspension inhibited metal release, suggesting that microbial catalysis can regulate metal mobilization during sediment resuspension. In a well buffered system, oxidation of iron sulfides alone did not appear to induce trace metal release. Moreover, when Trepangier sediment was resuspended in anoxic conditions at neutral pH, <1% of the trace metal content was released, whereas a significant release of metal was observed under acidic anoxic conditions. Although oxidation of iron sulfide minerals is an essential prerequisite for the release of Zn, Co, Cd, and Ni, carbonates and oxides also play a role. The trace metals and inorganic compounds investigated could be classified into three groups according to their release characteristics: (i) Mn, Zn, Cd, Ni, and Co; (ii) Fe, Pb, and As; and (iii) Cu. The groupings appeared to depend on the sources of compounds and their relative affinity, after oxidation, to iron oxyhydroxides or organic matter.     

Nitrate reduction in the presence of wüstite

Recent strategies to reduce elevated nitrate concentrations employ metallic Fe0 as a reductant. Secondary products of Fe0 corrosion include magnetite (Fe3O4), green rust [Fe6(OH)12SO4], and wüstite [FeO(s)]. To our knowledge, no studies have been reported on the reactivity of NO3- with FeO(s). This project was initiated to evaluate the reactivity of FeO(s) with NO3- under abiotic conditions. Stirred batch reactions were performed in an anaerobic chamber over a range of pH values (5.45, 6.45, and 7.45), initial FeO(s) concentrations (1, 5, and 10 g L(-1)), initial NO3- concentrations (1, 10, and 15 mM), and temperatures (3, 21, 31, and 41 degrees C) for kinetic and thermodynamic determinations. Suspensions were periodically removed and filtered to measure dissolved nitrogen and iron species. Solid phases were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Nitrate reduction by FeO was rapid and characterized by nearly stoichiometric conversion of NO3- to NH4+. Transient NO2- formation also occurred. The XRD and SEM results indicated the formation of Fe3O4 as a reaction product of the heterogeneous redox reaction. Kinetics of NO3- reduction suggested a rate equation of the type: -d[NO3-]/dt = k[FeO]0.57[H]0.22[NO3-]1.12 where k = 3.46 x 10(-3) +/- 0.38 x 10(-3) M(-1) s(-1), at 25 degrees C. Arrhenius and Eyring plots indicate that the reaction is surface chemical-controlled and proceeds by an associative mechanism involving a step where both NO3- and FeO(s) bind together in an intermediate complex.     

Removal of Pb(II) from wastewater using wheat bran

The adsorption of Pb(II) ions from aqueous solutions on wheat bran (WB) has been investigated as a function of initial concentration, adsorbent dose, adsorbent particle size, agitation speed, temperature, contact time and pH of solution. The equilibrium process was described well by the Langmuir isotherm model with maximum sorption capacities of 69.0, 80.7 and 87.0 mgg(-1) of Pb(II) on wheat bran at 20, 40 and 60 degrees C, respectively. Thermodynamic parameters, i.e. DeltaG(0), DeltaH(0) and DeltaS(0) have also been calculated for the system and the sorption process was found to be endothermic. Good correlation coefficients were obtained for the pseudo second-order kinetic model. The metal ion could be stripped by addition of 0.5M HCl, making the adsorbent regeneration and its reutilization possible.     

STRATEGIES FOR SEPARATING METALS FROM ACID MINE WATERS1

ABSTRACT: Strategies for the precipitation and separation of the primary metal ions, Fe(II), Cu(II), Zn(II), Mn(II), and Cd(II) in acid waste waters such as those in tributaries of the upper Sacramento River in northern California, are discussed. The strategies exploit the: (1) differential oxygen and hydrogen peroxide oxidation and precipitation properties of the metal ions as a function of pH, (2) the addition of ions, such as Mg^{2 +} and Cl^-, to reduce unfavorable coprecipitation, and (3) the facilitation of oxidation-reduction reactions between metal ions and the stabilization of particular oxidation states. This may be accomplished with specific complexing agents such as thiocyanate, SCN^-, and thiourea (TU), S = C(NH₂)₂ in order to separate copper at low pH as Cu(I) using Fe(II) as a reducing agent.     

油田含油污水高级氧化技术研究

以气浮—过滤预处理后的污水为处理对象,通过臭氧氧化与Fenton氧化两种方法处理油田含油污水。经实验验证:Fenton在pH为4,H2O2初始浓度为0.08mol/L,Fe2+与H2O2的摩尔比为1:10,H2O2与CODCr的质量比为1:1,反应时间为60min的条件下,去除率达54.3%(CODCr100mg/L),可达到GB8978-1996《污水综合排放标准》二级标准。     

Vivianite precipitation and phosphate sorption following iron reduction in anoxic soils

Phosphorus retention in lowland soils depends on redox conditions. The aim of this study was to evaluate how the Fe(III) reduction degree affects phosphate adsorption and precipitation. Two similarly P-saturated, ferric Fe-rich lowland soils, a sandy and a peat soil, were incubated under anaerobic conditions. M?ssbauer spectroscopy demonstrated that Fe(III) in the sandy soil was present as goethite and phyllosilicates, whereas Fe(III) in the peat soil was mainly present as polynuclear, Fe-humic complexes. Following anoxic incubation, extensive formation of Fe(II) in the solids occurred. After 100 d, the Fe(II) production reached its maximum and 34% of the citrate-bicarbonate-dithionite extractable Fe (Fe(CBD)) was reduced to Fe(II) in the sandy soil. The peat soil showed a much faster reduction of Fe(III) and the maximum reduction of 89% of Fe(CBD) was reached after 200 d. Neoformation of a metavivianite/vivianite phase under anoxic conditions was identified by X-ray diffraction in the peat. The sandy soil exhibited small changes in the point of zero net sorption (EPC?) and P(i) desorption with increasing Fe(III) reduction, whereas in the peat soil P desorption increased from 80 to 3100 μmol kg?1 and EPC? increased from 1.7 to 83 μM, after 322 d of anoxic incubation. The fast Fe(III) reduction made the peat soils particularly vulnerable to changes in redox conditions. However, the precipitation of vivianite/metavivianite minerals may control soluble P(i) concentrations to between 2 and 3 μM in the long term if the soil is not disturbed.     

Sorption of hazardous metals from single and multi-element solutions by saltbush biomass in batch and continuous mode: interference of calcium and magnesium in batch mode

Batch studies were performed to determine the interference of calcium (Ca) and magnesium (Mg) on the sorption of Cu(II), Cd(II), Cr(III), Cr(VI), Pb(II), and Zn(II) [from CuSO(4), K(2)Cr(2)O(7), Pb(NO(3))(2), Cr(NO(3))(3), ZnCl(2), and Cd(NO(3))(2)] by saltbush (Atriplex canescens) biomass. The results demonstrated that Ca and Mg at concentrations of at least 20 times higher than the concentration of most of the target metals did not interfere with the metal binding. The data show that the batch binding capacity from a multimetal solution at pH 5.0 was (micromol/g) about 260 for Cr(III) and Pb, and about 117, 54, and 49 for Cu, Zn, and Cd, respectively. The use of 0.1M HCl allowed the recovery of 85-100% of the bound Cu, Cr(III), and Pb, and more than 37% of the bound Cd and Zn. The column binding capacity for Pb was about 49 micromol/g from both the single and multimetal solutions, while it was, respectively about 35 and 23 micromol/g for Cr(III). The binding capacity for Cu and Zn from the single and multimetal column experiments was 35 micromol/g and less than 10 micromol/g, respectively. The stripping data from the single column experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and Zn, 90% and 74% of the bound Pb and Cr(VI), respectively, and less than 25% of the bound Cd and Cr(III), while the stripping from the multimetal experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and about 74%, 54%, 43%, and 40% of the bound Pb, Zn, Cd, and Cr(III), respectively.     

Tolerance (PICT) of the bacterial communities to copper in vineyards soils from Spain

To detect effects of Cu pollution, the Cu tolerance of soil bacterial communities extracted from several vineyards located in NW Spain was measured. Bacterial community tolerance was estimated by means of the thymidine (TdR) and leucine (Leu) incorporation techniques using either IC(50) values (the log of the metal concentration that reduced incorporation to 50%) or the percentage of activity at one specific Cu concentration (10(-6) mol L(-1)). The tolerance measurements by the TdR incorporation technique were similar to those obtained by the Leu incorporation method, indicating that the two methods were equivalent in terms of suitability for detecting the toxicity of Cu to soil bacterial communities. The two tolerance indices considered (IC50 values and percentage of activity) were closely correlated (r = 0.975, P < 0.001), showing that both were equally good in measuring Cu tolerance of the bacterial community. An increased bacterial community tolerance to Cu, indicating a pollution effect, was observed in vineyard soils with more than 100 mg Cu kg(-1) soil. Thus, the long-term use of Cu in vineyards has a toxic effect on the soil bacterial community, resulting in an increased tolerance. An effect of increased levels of Cu could not be detected when measuring bacterial community activity, pointing to the increased sensitivity to detect toxicity in field studies using tolerance measurements.     

Biosorption of copper(II) and lead(II) onto potassium hydroxide treated pine cone powder

Pine cone powder surface was treated with potassium hydroxide and applied for copper(II) and lead(II) removal from solution. Isotherm experiments and desorption tests were conducted and kinetic analysis was performed with increasing temperatures.As solution pH increased, the biosorption capacity and the change in hydrogen ion concentration in solution increased. The change in hydrogen ion concentration for lead(II) biosorption was slightly higher than for copper(II) biosorption. The results revealed that ion-exchange is the main mechanism for biosorption for both metal ions. The pseudo-first order kinetic model was unable to describe the biosorption process throughout the effective biosorption period while the modified pseudo-first order kinetics gave a better fit but could not predict the experimentally observed equilibrium capacities. The pseudo-second order kinetics gave a better fit to the experimental data over the temperature range from 291 to 347 K and the equilibrium capacity increased from 15.73 to 19.22 mg g^?1 for copper(II) and from 23.74 to 26.27 for lead(II).Activation energy was higher for lead(II) (22.40 kJ mol^?1) than for copper(II) (20.36 kJ mol^?1). The free energy of activation was higher for lead(II) than for copper(II) and the values of ΔH* and ΔS* indicate that the contribution of reorientation to the activation stage is higher for lead(II) than copper(II). This implies that lead(II) biosorption is more spontaneous than copper(II) biosorption.Equilibrium studies showed that the Langmuir isotherm gave a better fit for the equilibrium data indicating monolayer coverage of the biosorbent surface. There was only a small interaction between metal ions when simultaneously biosorbed and cation competition was higher for the Cu-Pb system than for the Pb-Cu system. Desorption studies and the Dubinin–Radushkevich isotherm and energy parameter, E, also support the ion-exchange mechanism.