Evaluation of the STP model: Comparison of modelled and experimental results for ten polycyclic aromatic hydrocarbons (PAHs)

Screening level risk assessment models are used by many countries to assess the treatability of organic chemicals during the sewage treatment process, especially those that are new to commerce. The performance of one such model, the sewage treatment plant model, is evaluated in the current study by comparing model predictions with actual measurement data collected at various stages of a typical full-scale activated sludge type sewage treatment plant. A suite of ten polycyclic aromatic hydrocarbons (PAHs) with widely varying physico–chemical properties were monitored for the comparison. Model predicted removal efficiencies were in very good agreement with those measured for all ten PAHs. Observed chemical concentrations and their trends at various stages of the sewage treatment process were also well simulated by the model. Results also suggest that a reasonable first approximation estimate of a range for the biodegradation half-life needed for the model may be obtained by dividing reported aqueous biodegradation half-life by scaling factors of 50 and 150.     

PAH removal from spiked municipal wastewater sewage sludge using biological, chemical and electrochemical treatments

Polycyclic aromatic hydrocarbons (PAHs) have been widely studied due to their presence in all the environmental media and toxicity to life. These molecules are strongly adsorbed on the particulate matters of soils, sludges or sediments because of their strong hydrophobicity which makes them less bioavailability, thus limiting their bioremediation. Different sludge treatment processes were tested to evaluate their performances for PAH removal from sludge prealably doped with 11 PAHs (5.5mg each PAH kg(-1) of dry matter (DM)): two biological processes (mesophilic aerobic digestion (MAD) and simultaneous sewage sludge digestion and metal leaching (METIX-BS)) were tested to evaluate PAH biodegradation in sewage sludge. In parallel, two chemical processes (quite similar Fenton processes: chemical metal leaching (METIX-AC) and chemical stabilization (STABIOX)) and one electrochemical process (electrochemical stabilization (ELECSTAB)) were tested to measure PAH removal by these oxidative processes. Moreover, PAH solubilisation from sludge by addition of a nonionic surfactant Tween 80 (Tw80) was also tested. The best yields of PAH removal were obtained by MAD and METIX-BS with more than 95% 3-ring PAH removal after a 21-day treatment period. Tw80 addition during MAD treatment increased 4-ring PAHs removal rate. In addition, more than 45% of 3-ring PAHs were removed from sludge by METIX-AC and during ELECSTAB process were quiet good with approximately 62% of 3-ring PAHs removal. However, little weaker removal of 3-ring PAHs (<35%) by STABIOX. None of the tested processes were efficient for the elimination of high molecular weight (> or = 5-ring) PAHs from sludge.     

Successful Treatment of Low PAH-Contaminated Sewage Sludge in Aerobic Bioreactors (7 pp) *

Background, Aims and Scope Polycyclic Aromatic Hydrocarbons (PAHs) are known for their adverse and cumulative effects at low concentration. In particular, the PAHs accumulate in sewage sludge during wastewater treatment, and may thereafter contaminate agricultural soils by spreading sludge on land. Therefore, sludge treatment processes constitute the unique opportunity of PAH removal before their release in the environment. In this study, the ability of aerobic microorganisms to degrade light and heavy PAHs was investigated in continuous bioreactors treating trace-level PAH-contaminated sludge. Methods Several aerobic reactors were operated under continuous and perfectly mixed conditions to simulate actual aerobic sludge digesters. Three sterile control reactors were performed at 35°C, 45°C or 55°C to assess PAH abiotic losses under mesophilic and thermophilic conditions. Three biological reactors were also operated at 35°C, 45°C or 55°C. Furthermore, 250 mM methanol were added in an additional mesophilic reactor (35°C). All reactors were fed with long-term PAH-contaminated sewage sludge, and PAH removal was assessed by inlet/outlet mass balance. In this study, PAH compounds ranged from 2 to 5-unsubstituted aromatic rings, i.e. respectively from Fluorene to Indeno(123cd)pyrene. Results and Discussion Significant abiotic losses were observed for the lightest PAHs (fluorene, phenanthrene and anthracene), while biodegradation occurred for all PAHs. More than 80% of the lightest PAHs were removed. Biodegradation rates inversely correlated with the increasing molecular weight, and seemed limited by the low bioavailability of the heaviest PAHs (only 50% of removal). The enhancement of PAH bioavailability by increasing the process temperature or adding methanol was tested. A temperature increase from 35°C to 45°C and then to 55°C significantly enhanced the biodegradation of the heaviest PAHs from 50% to 80%. However, high abiotic losses were observed for all PAHs at 55°C, which was attributed to volatilization. Optimal conditions were found at 45°C considering the low abiotic losses and the high PAH biodegradation rates. Similar performances were achieved by addition of methanol in the sludge. It was concluded that increasing temperatures or addition of methanol favored PAH diffusion from solids to an aqueous compartment, and enhanced their bioavailability to PAH-degrading microorganisms. Conclusion In this study, the use of long-term acclimated aerobic ecosystems showed the high potential of aerobic microorganisms to degrade a wide range of PAHs at trace levels. However, PAH biodegradation was likely controlled by their low bioavailability. Two aerobic processes have been finally proposed to achieve efficient decontamination of sewage sludge, at 45°C or in the presence of methanol. The PAH concentrations in reactor outlet were lower than the French requirements, and allow the treated sludge to be spread on agricultural land. Recommendations and Outlook The two proposed aerobic processes used physical or chemical diffusing agents. The global ecological impact of using the latter agents for treating trace level contamination must be considered. Since methanol was completely removed during the process, no additional harm is expected after treatment. However, an increase of temperature to 45°C could drastically increase the energy demand in full-scale plants, and therefore the ecological impact of the process. Moreover, since bioavailability controls PAH biodegradation, efficiency of the processes could also be influenced by the hydraulic parameters, such as mixing and aeration rates. Further experimentations in a pilot scale are therefore recommended, as well as a final assessment of the global environmental benefit of using such aerobic processes in the bioremediation of trace level compounds. - Abbreviations (PAHs): Ant – anthracene; B(a)A – benzo(a)anthracene ; B(b)F – benzo(b)fluoranthene; B(k)F – benzo(k)fluoranthene; B(ghi)P – benzo(g,h,i)perylene; B(a)P – benzo(a)pyrene; Chrys – chrysene; DB – dibenzo(a,h)anthracene; Fluor – fluoranthene; Fluo - fluorene; Ind – indeno(1,2,3-c,d)pyrene; Phe - phenanthrene; Pyr – pyrene - * The basis of this peer-reviewed paper is a presentation at the 9th FECS Conference on 'Chemistry and Environment', 29 August to 1 September 2004, Bordeaux, France.     

Enhanced degradation of polycyclic aromatic hydrocarbons by biodegradation combined with a modified Fenton reaction

A study has been conducted to enhance degradation of a mixture of polycyclic aromatic hydrocarbons (PAHs) by combining biodegradation with hydrogen peroxide oxidation in a former manufactured gas plant (MGP) soil. An active bacterial consortium enriched from the MGP surface soil (0-2 m) biodegraded more than 90% of PAHs including 2-, 3-, and 4-ring hydrocarbons in a model soil. The consortium was also able to transform about 50% of 4- and 5-ring hydrocarbons in the MGP soil. As a chemical oxidant, Fenton's reagent (H2O2 + Fe2+) was very efficient in the destruction of a mixture of PAHs (i.e., naphthalene (NAP), fluorene (FLU), phenanthrene (PHE), anthracene (ANT), pyrene (PYR), chrysene (CHR), and benzo(a)pyrene (BaP)) in the model soil; noticeably, 84.5% and 96.7% of initial PYR and BaP were degraded, respectively. In the MGP soil, the same treatment destroyed more than 80% of 2- and 3-ring hydrocarbons and 20-40% of 4- and 5-ring compounds. However, the low pH requirement (pH 2-3) for optimum Fenton reaction made the process incompatible with biological treatment and posed potential hazards to the soil ecosystem where the reagent was used. In order to overcome such limitation, a modified Fenton-type reaction was performed at near neutral pH by using ferric ions and chelating agents such as catechol and gallic acid. By the combined treatment of the modified Fenton reaction and biodegradation, more than 98% of 2- or 3-ring hydrocarbons and between 70% and 85% of 4- or 5-ring compounds were degraded in the MGP soil, while maintaining its pH about 6-6.5.     

The removal of Polycyclic Aromatic Hydrocarbons in the wastewater treatment process: experimental calculations and model predictions

The removal of PAHs during the wastewater treatment process was examined in an activated sludge mode conventional facility. Concentrations reported are taken from an earlier measuring campaign. Removals of PAHs ranged between 28 and 67% in the primary, <1-61% in the secondary stage, and 37-89% in the whole process. Significant positive relationships were observed for removal efficiencies and the log K(ow) of PAHs in the primary and the log K(H) of PAHs in the secondary stage. Experimental removals were compared to those obtained from the FATE model. In the primary stage, predicted removals were lower than those experimentally calculated while in the secondary stage were higher. Predicted removals were apportioned mainly to sorption with negligible contribution from volatilization and biodegradation. Remarkable consistency between experimental and modeled removal efficiencies (-20-+20%) was observed for almost all PAHs in the whole treatment process.     

Correlation between inorganic (heavy metals) and organic (PCBs and PAHs) micropollutant concentrations during sewage sludge composting processes

The nature and congener composition of PCBs and PAHs present in sewage sludge composting processes was investigated. These studies included analysis of the most significant process parameters (such as pH, temperature, weight percentage variation) and in addition heavy metals whose typical composting speciation and behaviour were also considered in order to better understand organic compound time profiles. The significant correlation found between Pb, Cd, Cu and PCBs and between PAHs and Hg implies that quite a strong adsorption of PCBs onto organic matter takes place and also provides evidence for the volatilisation of PAHs. Chemical characteristics of inorganic species and organic compounds are summarised to account for the observed correlation and time trend profiles. Moreover, single congener concentrations demonstrate that the number of Cl substituents for PCBs and condensed benzene rings for PAHs determine to what extent they can be broken down for biodegradation and removed through volatilisation respectively.     

A review of the environmental fate and aquatic effects of a series of C4 and C8 oxo-process chemicals

Semipermeable membrane devices containing a neutral lipid triolein (triolein-SPMD) and conventional dichloromethane extraction were used to monitor the presence and concentrations of priority organic pollutants in a sewage treatment process in Beijing, China. Both samples gave similar information on the presence of target PCB congeners, PAHs, Organochlorine pesticides and substituted benzenes in sewage at all sites. After 20 days' sampling, the concentrations of contaminants in triolein of SPMD were much higher than those in dichloromethane extracts, which resulted in easier analysis, improved the detection limits, and increased the accuracy. Previous field mean sampling rates for SPMD were used to estimate concentrations of PCB congeners in sewage, which compared to their determined concentrations by dichloromethane extraction. The consistency and superiority of SPMD technology were proved for the detection of priority organic contaminants from sewage. Lower removal rates for PCB congeners and PAHs coincided with the persistence of them in environment. More attention should be paid to urban sewage treatment process adopting activated-sludge method, where priority organic pollutants might not be removed, even present higher concentrations after treatment.     

Biodegradation of polycyclic aromatic hydrocarbons in the natural waters of the Yellow River: effects of high sediment content on biodegradation

The contamination of polycyclic aromatic hydrocarbons (PAHs) has become one of the major problems in the Yellow River of China. As the Yellow River is the most turbid large river in the world, it remains unknown to which extent the high suspended sediment content in the river may affect the fate and effect of PAHs. Here we report the effect of sediment on biodegradation of chrysene, benzo(a)pyrene and benzo(g,h,i)perylene with phenanthrene as a co-metabolism substrate in natural waters from the Yellow River. Biodegradation kinetics of the PAHs in the river water with various levels of sediment contents were studied in the laboratory by fitting with a biodegradation kinetics model for organic compounds not supporting growth. The results indicated that the biodegradation rates of PAHs increased with the sediment content in the water. When the sediment contents were 0, 4 and 10 g/l, the biodegradation rate constants of chrysene with the initial concentration of 3.80 microg/l were 0.053, 0.084 and 0.111 d(-1), respectively. Further studies suggested the enhanced biodegradation rate in the presence of sediment was caused by the following mechanisms: (1) the population of PAH-degrading bacteria in the water system was found to increase with the sediment content; the bacteria population on sediment phase was far greater than that on water phase during the cultivation process; (2) the sorption of PAHs on the sediment phase was well described by the dual adsorption-partition model. Although the sorption capacity of PAH per unit weight of sediment decreased with the increase of the sediment content, the amount of sorbed PAH increased with the sediment content; and, (3) the desorption of PAHs from the solid phase led to a higher concentration near the water-sediment interface. Since the bacteria were also attached to the interface, this resulted in an increased contact chance between the bacteria and PAHs.     

二噁口英及类似有毒有害物的处理技术

二(口恶、口英)、多氯联苯、多环芳香烃及化学武器等有毒有害物的处理技术已取得长足进展.这些有毒有害物的处理技术可概括为物理方法、化学方法、物理化学方法和生物降解法.本文从概念、应用场合、分解效率以及操作条件等方面对这些方法分别进行了介绍,重点介绍和评述了吸附和催化法,以及应用前景很好的生物降解技术.     

Historical record and sources of polycyclic aromatic hydrocarbons in core sediments from the Yangtze Estuary, China

Polycyclic aromatic hydrocarbons (PAHs) in a sediment core taken from intertidal flat in the Yangtze Estuary were determined by gas chromatography-mass spectrometry. The results indicate that the total concentration of PAHs ranged from 0.08 to 11.74 microg/g. The concentration levels of total and individual PAHs changed dramatically with depth. The concentrations of PAHs were relatively high above 35 cm depth and remained constantly low below this depth. The historical record of PAHs in the core shows subsurface maximum (one or more peak values), followed by decreased levels to the surface and with depth. And, PAH sediment record in the core profile is in agreement with historically sewage discharge events during the 1980s to 1990s. The distribution of target molecule acenephthene, the fluoranthene/pyrene ratio, the proportion of 2-3-ring and 4-5-ring PAHs, and alkylated naphthalene to parent naphthalene in the core profile show that the sources in this area are characterized by petroleum-derived PAH contamination (mainly sewage discharge and the river runoff) and the incorporation of atmospheric inputs. Studies indicate the PAH profile pattern in this site in comparison with other regions appear to reflect its particular local position (near the sewage outlet). Moreover, physico-chemical conditions and sedimentation rate as well as biodegradation also affect the PAH concentration levels in the core sediments.     

Use of fugacity model to analyze temperature-dependent removal of micro-contaminants in sewage treatment plants

Effluents from sewage treatment plants (STPs) are known to contain residual micro-contaminants including endocrine disrupting chemicals (EDCs) despite the utilization of various removal processes. Temperature alters the efficacy of removal processes; however, experimental measurements of EDC removal at various temperatures are limited. Extrapolation of EDC behavior over a wide temperature range is possible using available physicochemical property data followed by the correction of temperature dependency. A level II fugacity-based STP model was employed by inputting parameters obtained from the literature and estimated by the US EPA’s Estimations Programs Interface (EPI) including EPI’s BIOWIN for temperature-dependent biodegradation half-lives. EDC removals in a three-stage activated sludge system were modeled under various temperatures and hydraulic retention times (HRTs) for representative compounds of various properties. Sensitivity analysis indicates that temperature plays a significant role in the model outcomes. Increasing temperature considerably enhances the removal of β-estradiol, ethinyestradiol, bisphenol, phenol, and tetrachloroethylene, but not testosterone with the highest biodegradation rate. The shortcomings of BIOWIN were mitigated by the correction of highly temperature-dependent biodegradation rates using the Arrhenius equation. The model predicts well the effects of operating temperature and HRTs on the removal via volatilization, adsorption, and biodegradation. The model also reveals that an impractically long HRT is needed to achieve a high EDC removal. The STP model along with temperature corrections is able to provide some useful insight into the different patterns of STP performance, and useful operational considerations relevant to EDC removal at winter low temperatures.     

Remediation of PAH contaminated soils: application of a solid-liquid two-phase partitioning bioreactor

The feasibility of a two-step treatment process has been assessed at laboratory scale for the remediation of soil contaminated with a model mixture of polycyclic aromatic hydrocarbons (PAHs) (phenanthrene, pyrene, and fluoranthene). The initial step of the process involved contacting contaminated soil with thermoplastic, polymeric pellets (polyurethane). The ability of three different mobilizing agents (water, surfactant (Biosolve) and isopropyl alcohol) to enhance recovery of PAHs from soil was investigated and the results were compared to the recovery of PAHs from dry soil. The presence of isopropyl alcohol had the greatest impact on PAH recovery with approximately 80% of the original mass of PAHs in the soil being absorbed by the polymer pellets in 48 h. The second stage of the suggested treatment involved regeneration of the PAH loaded polymers via PAH biodegradation, which was carried out in a solid-liquid two-phase partitioning bioreactor. In addition to the PAH containing polymer pellets, the bioreactor contained a microbial consortium that was pre-selected for its ability to degrade the model PAHs and after a 14 d period approximately 78%, 62% and 36% of phenanthrene, pyrene, and fluoranthene, respectively, had been desorbed from the polymer and degraded. The rate of phenanthrene degradation was shown to be limited by mass transfer of phenanthrene from the polymer pellets. In case of pyrene and fluoranthene a combination of mass transfer and biodegradation rate might have been limiting.     

Effects of anthracene, pyrene and benzo[a]pyrene spiking and sewage sludge compost amendment on soil ecotoxicity during a bioremediation process

The fate of spiked anthracene, pyrene and benzo[a]pyrene in soil with or without sewage sludge compost was assessed during a 6-month bioremediation process simulating landfarming. Bioassays and physico-chemical analyses were employed to monitor toxicity change in soil samples and elutriates through ten sampling campaigns. Pearson product-moment correlation coefficient was determined to measure the strength of relationship between bioassays and physico-chemical analyses. The PAH dissipation in soil was enhanced after the first water addition, and the remaining amounts at the end of the experiment were positively correlated to the number of benzene rings and the presence of sewage sludge compost. Toxicity of soil elutriates to Daphnia magna was evident at early stages, originating exclusively from sewage sludge compost amendment. The lettuce root elongation was continuously inhibited by elutriates for all the treatments including control soil, probably due to high salinity or to unaddressed leachable phytotoxic compounds that were present in the experimental soil. The newly developed direct solid-phase chronic toxicity test using ostracod (Heterocypris incongruens) succeeded in evaluating the soil-bound PAH toxicity, as PAHs could not be detected in elutriates.     

Treatment of PAHs in contaminated soil by extraction with aqueous DNA followed by biodegradation with a pure culture of Sphingomonas sp

The biodegradation of polycyclic aromatic hydrocarbons (PAHs) in aqueous deoxyribonucleic acid (DNA) solution from contaminated soil washing was investigated. Initial data with a model effluent consisting of anthracene, phenanthrene, pyrene and benzo[a]pyrene that were individually dissolved in 1% aqueous DNA solution confirmed their positive degradation by Sphingomonas sp. at around 10(8)CFU mL(-1) initial cell loading. For anthracene and phenanthrene, complete removal was achieved within 1h treatment. Degradation of pyrene and benzo[a]pyrene took a relatively longer time of a few days and weeks, respectively. DNA-dissolved PAHs were also degraded relatively faster than PAH crystals in aqueous medium to suggest that the binding of the PAHs in the polymer does not pose serious constraint to bacterial uptake. The DNA was stable against the PAH-degrading bacteria. Parallel experiments with actual DNA solutions obtained during pyrene extraction from an artificially spiked soil also showed similar results. Close to 100% pyrene degradation was achieved after 1d treatment. With its chemical stability, the cell-treated DNA was re-used up to four cycles without a considerable decline in extraction performance.     

Changes of polycyclic aromatic hydrocarbons during composting of sewage sludges with chosen physico-chemical properties and PAHs content

The aim of the experiment was to determine changes in the PAH content during sewage sludge composting. The extent was evaluated to which sewage sludge properties influences on PAHs losses during composting. Five municipal sewage sludges were studied from sewage treatment plants located in the south-east of Poland, i.e. in Stalowa Wola, Kra?nik, Lublin, Zamo?? and Bi?goraj. The treatment plants selected were characterised by their differentiation with catchments area as well as the industrial character of the areas. Sludge composting was carried out in aerobic conditions in plastic containers for a period of 76 days. The content of 14 polycyclic aromatic hydrocarbons (PAHs) and some physical-chemical (TOC, Nt, TOC/Nt, CEC, BS, TEB, pH, available potassium and phosphorus, total forms of cations) sewage sludge properties were monitored. In the present study correlations between PAHs losses (during various phases of composting) and physical-chemical properties of sewage sludges and composts were also evaluated. The sewage sludges were characterised both by differentiated properties and by PAH content. The total PAH content (the sum of 14 PAHs from the EPA List with exception of naphthalene and acenaphthene) in the sludges ranged from 3674 to 11236 microg kg(-1). Four- and three-ring compounds were predominant in the sewage sludges. Almost all of the sludges were characterised by differentiated content levels of both individual PAHs groups and PAHs sum. After 76 days of composting, a significant lowering of the PAH content was observed in all sludges as compared to the beginning of the experiment. The range of total observed PAH losses was from 15.8% to 48.6%, depending on the sewage sludge. The largest lowering of the PAH content was observed in the sludge with the lowest concentration of the xenobiotics studied. The largest losses in individual PAHs were observed in the case of five- and six-rings compounds, and were probably related to strong pollutant binding by other components of the sewage sludge. The few significant relationships showed that PAH losses during composting were only slightly determined by the analysed physical-chemical properties.     

Levels of dioxin-like compounds in sewage sludge determined with a bioassay based on EROD induction in chicken embryo liver cultures

A bioassay for the detection of dioxin-like compounds was used to estimate levels in sewage sludge from Swedish sewage treatment plants (STPs). The sludge extracts were HPLC-separated into three fractions containing a) monoaromatic/aliphatic, b) diaromatic (e.g. polychlorinated biphenyls [PCBs], polychlorinated dibenzodioxins and polychlorinated dibenzofurans [PCDDs/Fs]), and c) polyaromatic compounds (e.g. polycyclic aromatic hydrocarbons [PAHs]). The bioassay, which is based on EROD (7-ethoxyresorufin O-deethylase) induction in cultured chicken embryo livers detected dioxin-like activity in all unfractionated extracts and in the di- and polyaromatic fractions of all sludge extracts, but not in the monoaromatic/aliphatic fractions. The levels ranged between 6 and 109 pg bio-TEQ/g sludge (d.w.). In sediment samples from rural lakes in Sweden, levels of about 5 pg bio-TEQ/g (d.w.) have been found. The polyaromatic fractions of the sludge samples were potent in the bioassay, probably due to various PAHs and other polyaromatics in the sludge. The levels of six PAHs that are screened for in the sludge at Swedish STPs accounted for only 3-10% of the observed EROD-induction by the polyaromatic fractions. Consequently, many other polyaromatic EROD-inducing compounds were present in the sludge. Inclusion of a biological test like the chicken embryo liver bioassay in the screening of sludge would improve the ability to detect the presence of bioactive dioxin-like compounds. A theoretical estimation of bio-TEQ concentrations in farm-soil following long-term application of sludge with bio-TEQ concentrations similar to those observed in this investigation indicated that the bio-TEQ levels in soil would increase very slowly over time. The chicken embryo liver bioassay proved useful in assessing levels of dioxin-like compounds in sewage sludge and it gives valuable complementary information to chemical analysis data.     

底泥中多环芳烃的处理技术进展

底泥中多环芳烃（PAHs）的处理方法主要有物化处理和生物处理。物化处理方法有湿式空气氧化、溶剂浸提、热解吸等；生物处理有好氧处理和厌氧处理。物化处理速度快、效果明显，但能耗高、投资大；生物处理方法虽然能耗低，但速度慢、降解率较低。实际运用中宜发展物化和生物的组合工艺。     

Solid-phase bioassays and soil microbial activities to evaluate PAH-spiked soil ecotoxicity after a long-term bioremediation process simulating landfarming

The residual ecotoxicity of long-term bioremediated soils concomitantly spiked with three PAHs at four levels (15, 75, 150, 300 mg Sigma 3 PAHs kg(-1) soil) was evaluated using physico-chemical analyses, solid-phase bioassays and soil microbial activities. The pot-scale bioremediation process consisted of weekly moderate waterings in the presence or absence of sewage sludge compost (SSC) under greenhouse conditions. After 15 months, anthracene and pyrene were almost completely degraded whereas benzo[a]pyrene was still persisting, most apparently in SSC-amended soil treatments. However, no apparent toxic effects of the residual PAHs could be detected. SSC application at 40 t ha(-1) was performed to valorize the biowaste and stimulate PAH biodegradation but caused soil salinization and pH reduction at the end of the bioremediation process. Consequently, SSC-amended soils were characterized by strong phytotoxicity to lettuce and had adverse effects on the ostracod Heterocypris incongruens. Despite the smaller number of culturable bacterial populations in SSC-amended soils, soil enzymatic activities were not affected by the organic amendment and residual PAHs; and the bioremediation efficiency was likely to be more limited by the bioavailability of PAHs rather than by the total number of PAH-degraders.     

Evaluation of municipal sewage treatment systems for pollutant removal efficiency by measuring levels of micropollutants

In order to evaluate the municipal sewage treatment systems used at Harbin municipal sewage treatment plant for their pollutant removal efficiency, raw sewage and effluent samples at different treatment stages from the sewage treatment systems were taken, priority pollutants (PPs) were identified and quantified using gas chromatography-mass spectrometry (GC-MS) and inductively coupled plasma-atomic emission spectrograph (ICP-AES). The test results indicated that there were one hundred and fifty species of organic pollutants identified in the raw sewage sample, and only ten species of PPs in all the sewage samples. The levels of dimethyl phthalate (DMP), diethyl phthalate (DEP), dibutyl phthalate (DBP), di-n-octyl phthalate (DnOP) in the sewage samples were 0.779-0.111 microg l(-1), 1.977-0.022 microg l(-1), 6.411-2.194 microg l(-1) and 7.152-2.953microg l(-1), respectively, and most of these phthalate esters (PAEs) were removed through anaerobic/aerobic (A/O) process; The levels of alachlor, acetochlor, atrazine were 0.074-0.021 microg l(-1), 0.160-0.096 microg l(-1) and 0.238-0.184 microg l(-1), respectively, and the total removal efficiency of atrazine was poorest through the sewage treatment systems. The levels of Cu, Cr, Se, Hg, Ni and Zn were 0.0030-0.2327 mg l(-1). It is therefore concluded from these results that the sewage treatment systems were efficient in removing most of the organic and inorganic compounds in this study, and so, the discharged effluent could cause little of the secondary pollution of the aquatic environment.     

Plant performance, dioxygenase-expressing rhizosphere bacteria, and biodegradation of weathered hydrocarbons in contaminated soil

Two greenhouse pot experiments were conducted to investigate the potential of 13 plant species (grasses, cruciferes, legumes, herbs) to thrive in a long-term contaminated soil from a former manufactured gas plant (MGP) site, to promote the proliferation of total and aromatic ring dioxygenase-expressing bacteria (ARDB) in the root zone, and to foster the biodegradation of petrol hydrocarbons (PHCs) and polycyclic aromatic hydrocarbons (PAHs). PHCs at 23200 mg kg(-1) and PAHs at 2194 mg kg(-1) reduced seed germination, plant survival, and shoot yields for most plants. Total bacteria and ARDB were generally more abundant in contaminated soil and were most numerous in the rhizosphere of mustard. During 68 d, the loss of total petrol hydrocarbons (TPHs) and total US EPA priority PAHs (TPAHs) was greatest in soil planted with hemp and mustard. Pea, cress, and pansy increased the amounts of PAHs extracted from soil, including an almost 60% increase for dibenzo(ah)anthracene. Plants may enhance the chemical extractability and perhaps biological availability of initially unextractable molecules.