Food irradiation

The use of irradation to improve the safety, protect the nutritional benefits, and preserve the quality of fresh and processed foods is a well established and proven technology. Over the past 30 years, the United States Government has invested in the science to confirm safety and in the technology to show application. The United States Department of Agriculture and the Food and Drug Administration have approved sources of ionizing radiation for the treatment of foods, and their application to most meats, fruits, vegetables, and spices. Despite the value of this technology to the food industry and to the health and welfare of the public, only minimal application of this technology occurs. This underscorces the importance of increasing the public’s understanding of radiation risks relative to other hazards. Accordingly, the Committee on Interagency Radiation Research and Policy Coordination of the Executive Office of the President has made recommendations for the creation of a centralized National Radiation Information Center that would work closely with Federal departments and agencies in responding to public queries about radiation issues and Federal programs.     

Methodology for estimating soil carbon for the forest carbon budget model of the United States, 2001

The largest carbon (C) pool in United States forests is the soil C pool. We present methodology and soil C pool estimates used in the FORCARB model, which estimates and projects forest carbon budgets for the United States. The methodology balances knowledge, uncertainties, and ease of use. The estimates are calculated using the USDA Natural Resources Conservation Service STATSGO database, with soil dynamics following assumptions based on results of site-specific studies, and area estimates from the USDA Forest Service. Forest Inventory and Analysis data and national-level land cover data sets. Harvesting is assumed to have no effect on soil C. Land use change and forest type transitions affect soil C. We apply the methodology to the southeastern region of the United States as a case study.     

Analysis of cloud and precipitation chemistry at Whiteface Mountain,NY

Federal and state programs over the past two decades have resulted in the reduction of emissions of precursors of acid rain. Concomitant with these changes, measured concentrations of acidity in precipitation and in watersheds have shown a downward trend or improvement. However, another pathway for these precursors is through cloud and fog events that often tend to occur at high-elevation regions affecting the fauna and flora as well. In this study we report on long-term measurements of cloud water and precipitation chemistry made from 1994 onwards at a high-elevation location, Whiteface Mountain NY, in the northeastern United States. Trends and inter-relationship between the ions were examined along with ambient SO₂ measurements and Adirondack lakes chemistry data.     

Review of light-duty diesel and heavy-duty diesel gasoline inspection programs

Emissions from diesel vehicles and gas-powered heavy-duty vehicles are becoming a new focus of many inspection and maintenance (I/M) programs. Diesel particulate matter (PM) is increasingly becoming more recognized as an important health concern, while at the same time, the public awareness of diesel PM emissions because of their visibility have combined to increase the focus on diesel emissions in the United States. This has resulted in an increased interest by some states in including heavy-duty vehicle testing in their I/M program. This paper provides an overview of existing I/M programs focused on testing light-duty diesel vehicles, heavy-duty diesel vehicles, and heavy-duty gasoline vehicles (HDGVs). Information on 39 I/M programs in 27 different states in the United States plus 9 international inspection programs is included. Information on the status of diesel emissions technology and current test procedures is also presented. The goal is to provide useful information for air quality managers as they work to decide whether such I/M programs would be worth pursuing in their respective areas and in evaluating the emissions measurement technology to be used in the program. Testing of HDGVs is generally limited to idle testing, because dynamometer testing of these vehicles is not practical, and most were not certified on a chassis basis. Testing of diesel vehicles has mostly been limited to SAE J1667 "snap-idle" opacity testing. Cost-effective technology for measuring diesel emissions currently does not exist, and, therefore, opacity-type measurements, although not effective at reducing the pollutants of most significant health concern, will continue to be used.     

Review of Light-Duty Diesel and Heavy-Duty Diesel Gasoline Inspection Programs

Abstract

Emissions from diesel vehicles and gas-powered heavyduty vehicles are becoming a new focus of many inspection and maintenance (I/M) programs. Diesel particulate matter (PM) is increasingly becoming more recognized as an important health concern, while at the same time, the public awareness of diesel PM emissions because of their visibility have combined to increase the focus on diesel emissions in the United States. This has resulted in an increased interest by some states in including heavy-duty vehicle testing in their I/M program.

This paper provides an overview of existing I/M programs focused on testing light-duty diesel vehicles, heavyduty diesel vehicles, and heavy-duty gasoline vehicles (HDGVs). Information on 39 I/M programs in 27 different states in the United States plus 9 international inspection programs is included. Information on the status of diesel emissions technology and current test procedures is also presented. The goal is to provide useful information for air quality managers as they work to decide whether such I/M programs would be worth pursuing in their respective areas and in evaluating the emissions measurement technology to be used in the program. Testing of HDGVs is generally limited to idle testing, because dynamometer testing of these vehicles is not practical, and most were not certified on a chassis basis.

Testing of diesel vehicles has mostly been limited to SAE J1667 “snap-idle” opacity testing. Cost-effective technology for measuring diesel emissions currently does not exist, and, therefore, opacity-type measurements, although not effective at reducing the pollutants of most significant health concern, will continue to be used.     

Guidelines and Resources for Conducting an Environmental Crime Investigation in the United States

Common environmental crimes in the United States include the illegal disposal of hazardous waste, unpermitted discharges to sewer systems or surface water, discharge of oil by vessels to waters within United States jurisdiction, the misapplication of pesticides, the illegal importation of ozone-depleting substances, data falsification, and laboratory fraud. Federal, state, and sometimes local statutes and regulations are in place to protect the water, air, land, and human health. From a federal perspective, these include the Resource Conservation and Recovery Act (RCRA) for hazardous wastes, the Toxic Substances Control Act (TSCA) for toxic substances, the Clean Air Act (CAA), the Clean Water Act (CWA), the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) for abandoned waste sites, and the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA) for pesticides. Each of these laws contains some standard methods for sampling and analyses to prove environmental crimes. The Code of Federal Regulations (CFR) contains the specific requirements of the laws. Within the United States Environmental Protection Agency (USEPA), the Criminal Investigation Division (CID) of the Office of Criminal Enforcement, Forensics and Training (OCEFT) has the responsibility to investigate criminal offenses.Criminal offenses are more serious in nature than civil violations in the United States. To successfully prosecute an environmental criminal case, the government has to prove, beyond a reasonable doubt, that a corporation or person knowingly violated an environmental statute containing criminal sanctions. The same environmental forensic techniques used to provide scientifically defensible data prevail in both civil and criminal cases; the only distinction between the two types of cases is legal.     

Setting the stage for the review of the international estimate of short-term intake (IESTI) equation

ABSTRACT

In the framework of setting Maximum Residue Limits (MRLs) for pesticides, both chronic and acute health risks to consumers arising from the long-term and short-term dietary exposure to pesticide residues have to be assessed. The current internationally harmonized approach for assessing the acute dietary exposure is based on deterministic methods for calculating the IESTI (International Estimate of Short-Term Intake). Recently, it became apparent that the IESTI approach needs a revision in the light of new scientific and political aspects. The main reasons that require this review were the lack of an international harmonization of the methodology which implies trade barriers as well as difficulties in risk communication concerning the public trust in regulatory systems. The most recent milestone in the scientific debate on a possible revision of the IESTI equation was an international scientific workshop held in Geneva in September 2015. The main objectives of this meeting were the re-evaluation, and where possible, the international harmonization of the input parameters for the IESTI equations as well as the equations themselves. The main recommendations from the workshop were (i) to replace the highest residue and supervised trials median residue with the maximum residue limit (MRL), (ii) to use a standard variability factor of three, (iii) to derive the P97.5 large portion value from the distribution of consumption values of dietary surveys expressed as kg food/kg bw/d, and (iv) to remove the commodity unit weight from the equations. In addition, the application of conversion factors and processing factors was addressed. On the initiative of the (World Health Organization) WHO Collaborating Centre on Chemical Food Safety at the National Institute for Public Health and the Environment (RIVM), the Netherlands, an international working group with members from the French Agency for Food, Environmental and Occupational Health and Safety, France (ANSES), Australian Pesticides and Veterinary Medicines Authority, Australia (APVMA), German Federal Institute for Risk Assessment, Germany (BfR), Chemical Regulation Division, the United Kingdom (CRD), European Food Safety Authority (EFSA), and RIVM, the Netherlands was formed after the IESTI workshop to conduct a comprehensive impact assessment of the proposed changes of the IESTI equations.     

Reducing the Risks from Radon

The U.S. Environmental Protection Agency estimates that residential radon levels in the United States lead to approximately 13,600 lung cancer deaths per year. To address this problem, the Agency has identified three program initiatives that can provide substantial reductions in the public’s risks: (1) public information activities that urge the public to test for radon and reduce elevated concentrations in existing homes, (2) new construction standards to reduce radon entry, and (3) radon testing and mitigation during real estate transactions. This paper analyzes the costs and risk reductions that could result from the implementation of these major initiatives, showing how all three elements cost-effectively protect the public’s health.     

Predicting and Managing the Health Risks of Sour-Gas Wells

The development of sour-gas resources in Canada and the United States has prompted concerns about the public health risks of accidental releases of gas contaminated with hydrogen sulfide (H₂S) from wells. This paper focuses on methods for improving the prediction and management of those risks. Data associated with the health effects of hydrogen sulfide are examined, and it is suggested that sublethal effects should be addressed in risk assessments of sour-gas wells along with the life-threatening effects normally considered. The demarcation of hazard zones around wells can be improved by using a statistical approach for estimating an upper-bound H₂S release rate; this rate can then be used in an atmospheric dispersion model to estimate maximum distances to downwind concentrations for lethal (300 ppmv) and sublethal (50 ppmv) effects resulting from an accidental release. A vertical release is found to have little impact, especially under stable atmospheric conditions; horizontal releases, on the other hand, result in the greatest downwind distances for health impacts. Management of health risks depends on a mix of safety technologies and contingency actions, such as well-ignition options and provision for post-release monitoring and assessment of ambient H₂S concentrations.     

Summary of efficacy evaluations using aerially applied Gypchek® against gypsy moth in the U.S.A.

Abstract

Gypchek^®, the gypsy moth (Lymantria dispar L.) nucleopolyhedrosis virus product, is manufactured by the United States Department of Agriculture (USDA) Forest Service, and Animal and Plant Health Inspection Service under controlled conditions in a laboratory strain of gypsy moth larvae. Gypchek was registered with the U.S. Environmental Protection Agency in 1978 as a general use pesticide to control gypsy moth. This product has been the subject of intense research and development targeted toward maximizing efficacy while minimizing the cost of production and application. The current Gypchek tank mix is applied at 1.25 × 10¹²occlusion bodies (OB's) per hectare for each of two applications (3‐days apart) at 18.7 litres/ha per application.     

The use of environmental risk assessment methodologies for an indoor air quality investigation

The authors of this paper chose several target compounds that have been found in average US homes, applied the current United States Environmental Protection Agency (USEPA) Superfund risk assessment methodologies to indoor air quality, and produced risk numbers for hazard quotients and predicted increases in incidence of cancer which would be unacceptable at US hazardous waste sites. The calculations were made for the average child and adult with USEPA default exposure values. Calculations were also made for a worst case scenario using maximum concentrations and exposure estimates defined by the USEPA as describing the reasonable exposure (RME). Significant cancer risks and non-cancer hazard quotients were predicted.     

A re-examination of ambient air ozone monitor interferences

Attaining the National Ambient Air Quality Standard (NAAQS) for ozone (O3) could cost billions of dollars nationwide. Attainment of the NAAQS is judged on O3 measurements made by the Federal Reference Method (FRM), ethylene chemiluminescence, or a Federal Equivalent Method (FEM), predominantly ultraviolet (UV) absorption. Starting in the 1980s, FRM monitors were replaced by FEMs so that today virtually all monitoring in the United States uses the UV methodology. This report summarizes a laboratory and collocated ambient air monitoring study of interferences in O3 monitors. Potential interferences examined in the laboratory included water vapor, mercury, o-nitrophenol, naphthalene, p-tolualdehyde, and mixed reaction products from smog chamber simulations of urban atmospheric photochemistry. UV absorption O3 monitors modified for humidity equilibration were also collocated with UV FEM O3 monitors at six sites in Houston, TX, during the 2007 summer O3 season. The results suggest that humidity and interfering species can positively bias (overestimate) O3 measured by FEM monitors used to determine compliance with the O3 standards. The results also suggest that humidity equilibration can mitigate this bias.     

Analysis of microbiological screen test data for antimicrobial residues in food animals

This study analyzes the National Residue Program (NRP) of the Food Safety and Inspection Service (FSIS), United States Department of Agriculture (USDA), data for the years 1983-1998 to determine the effectiveness of all three microbiological screen tests that were developed and used by the FSIS to control antimicrobial residues in food animals. The Swab Test On Premises (STOP) was the first screen test introduced in slaughterhouses, followed by the Calf Antibiotic Sulfonamide Test (CAST) and the Fast Antimicrobial Screen Test (FAST). The data for STOP indicates that during 1983-1998, the rate of food animal carcasses with violative levels of antimicrobial residues reduced from 2.33% to 0.45% under the monitoring plan and under the surveillance plan, the rate reduced from 55.1% to 0.56%. Similarly, the data for CAST indicates that the rate of calf carcasses with violative levels of antimicrobial residue also declined significantly during those years. Because of its higher sensitivity and shorter analytical time, the use of FAST started in 1995. By 1999, it had practically replaced the use of STOP and CAST in bovine species. The use of only one test such as FAST instead of different tests has removed confusion for testing different species of food animals and thereby has enhanced the efficiency of the NRP.     

The Crisis in Air Pollution Manpower Development

There is a crisis in air pollution manpower development within the United States today. This is the conclusion drawn from a series of three studies recently conducted by the National Air Pollution Manpower Development Advisory Committee. These studies, designed to define the essential components of a total manpower development program and to evaluate current efforts on specific segments of such a program, showed that the existing Federal manpower program fails to address many of the problem areas needing attention, that greater effort needs to be directed to meeting the air pollution educational requirements of State highway departments and planning agencies, and that the quality of most graduate level university programs in air pollution control is on the decline because of the withdrawal of Federal financial support.     

Characterization of Sonic Devices Used for Cleaning Fabric Filters

ABSTRACT

Ozone reactivity scales play an important role in selecting which chemical compounds are used in products ranging from gasoline to pesticides to hairspray in California, across the United States and around the world. The California Statewide Air Pollution Research Center (SAPRC) box model that calculates ozone reactivity uses a representative urban atmosphere to predict how much additional ozone forms for each kilogram of compound emission. This representative urban atmosphere has remained constant since 1988, even though more than 25 years of emissions controls have greatly reduced ambient ozone concentrations across the United States during this time period. Here we explore the effects of updating the representative urban atmosphere used for ozone reactivity calculations from 1988 to 2010 conditions by updating the meteorology, emission rates, concentration of initial conditions, concentration of background species, and composition of volatile organic compound (VOC) profiles. Box model scenarios are explored for 39 cities across the United States to calculate the Maximum Incremental Reactivity (MIR) scale for 1,233 individual compounds and compound-mixtures. Median MIR values across the cities decreased by approximately 20.3% when model conditions were updated. The decrease is primarily due to changes in atmospheric composition ultimately attributable to emissions control programs between 1998 and 2010. Further effects were caused by changes in meteorological variables stemming from shifting seasons for peak ozone events (summer versus early fall). Lumped model species with the highest MIR values in 1988 experienced the greatest decrease in MIR values when conditions were updated to 2010. Despite the reduction in the absolute reactivity in the updated 2010 atmosphere, the relative ranking of the VOCs according to their reactivity did not change strongly compared to the original 1988 atmosphere. These findings indicate that past decisions about ozone control programs remain valid today, and the ozone reactivity scale continues to provide relevant guidance for future policy decisions even as new products are developed.

Implications: Updating the representative urban atmosphere used for the Maximum Incremental Reactivity (MIR) scale from 1988 to 2010 conditions caused the reactivity of 1223 individual compounds and combined mixtures to decrease by an average of 20.3% but the relative ranking of the VOCs was not strongly affected. This means that previous guidance about preferred chemical formulations to reduce ozone formation in cities across the United States remain valid today, and the MIR scale continues to provide relevant guidance for future policy decisions even as new products are developed.     

The Use of Electrostatic Precipitators on Municipal Incinerators

Despite this country’s scientific advances, most communities in the United States are still disposing of solid wastes the way they did 50 years ago. The problem is advancing faster than the solution. Less than half the cities in this country with populations over 2500 dispose of their wastes by an approved sanitary and nuisance-free method. Do you realize that every 60 seconds people in the United States drop 251 tons of trash into their garbage cans. At the end of the day, 362,000 tons have accumulated. This means each of the 190 million people in the US disposes of 43½ lb of rubbish daily. By the year 2000 population is expected to double, while the per capita rate of increase in refuse production rises about 2% annually.

As the population booms and spreads to the suburbs, and suburbs expand into further suburbs, we will rapidly use up the land once used for waste disposal. Thus, sanitary landfill sites will disappear because by the year 2000 three-fourths of our population will live in urban areas.

The answer to this enormous problem faced by large and small communities is central incineration. Only this system can provide a maximum reduction in the volume of refuse. It is for this reason that communities are turning to incineration as the best solution. However, a growing public awareness plus changing municipal, state, and federal laws necessitate the need for a modern incineration plant that incorporates the most advanced and proved method of air pollution control. Where efficiencies of 60 to 80% were acceptable in the past, 90 to 95% are sought at present, and soon 96 to 99% will be required.

This paper deals with the effective control of particulate emissions from municipal incinerator exhaust gases.     

MTBE in California Drinking Water: An Analysis of Patterns and Trends

Over the past decade, there has been much publicity surrounding the impact of Methyl tert -butyl ether (MTBE) on drinking water supplies in the United States. In California, the presence of MTBE in groundwater and drinking water has led to a ban on the future use of MTBE in gasoline. Other states, such as those in the northeast, are also seeking ways to reduce or eliminate the use of MTBE due to perceived threats to the environment and public health. Despite claims about the incidence of MTBE in drinking water, no comprehensive characterization has been conducted on the available drinking water monitoring data. This paper provides a detailed analysis of the MTBE drinking water data compiled by the California Department of Health Services (CDHS) from 1995 to 2000. We find that MTBE was detected in about 1.3% of all drinking water samples, 2.5% of drinking water sources, and 3.7% of drinking water systems in California over this 6-year period. Our analysis reveals that many drinking water sources are not sampled routinely for MTBE, and in those sources that appear to be affected by MTBE, the compound is not consistently detected. The majority of MTBE detections are also concentrated in several geographic areas, which contain about 9-21% of the total California population. Average detected MTBE concentrations have decreased significantly since 1995 and 1996, ranging from 5 to 15 ppb over the last 3 years depending on the outcome of interest. Of the samples in which MTBE was present above the analytical detection limit, the concentrations in approximately 73% of drinking water samples and 86% of drinking water sources and systems were below the State's primary health-based standard of 13 ppb. Our findings suggest that, although some drinking water supplies in California have been affected by MTBE, the majority of drinking water sources and systems either have not been affected at all or contain MTBE at concentrations below levels that are likely to be of health concern.     

Legislating risk: the USA struggles to reform its policies for the assessment and management of risk

This paper focuses on recent efforts in the United States to improve the federal government's approach to regulating risk, with particular emphasis on legislation introduced in the Congress of the United States that was designed to reform and standardize risk assessment and risk management practices at the United States Environmental Protection Agency (EPA) and other federal agencies with responsibility for health, safety, and environmental regulation. After reviewing the key provisions of the legislation and the potential impact of those provisions on EPA's risk-related activities, the paper suggests certain fundamental principles that should guide the debate on reform of policies and procedures associated with risk.     

A comprehensive survey of graduate education and training in hazardous waste management

The United States Department of Health and Human Services through Wayne State University (WSU) has completed a study of hazardous waste education and training in the United States. The study documents university course work and degrees as well as non-degree continuing education short courses. Major portions of the study are based on a WSU sponsored survey in which 1469 four-year degree granting institutions were contacted. Of the 732 institutions responding, 113 were identified as offering course work of some kind in hazardous waste. Information on 499 distinct non-degree short courses was also gathered and evaluated. The purpose, methodology and results of the study are summarized in this article.     

Air Pollution Control Training in Colleges and Universities in the United States

A nationwide survey of air pollution control training efforts in the United States at colleges and universities was ccrried out for the S-l 1 Education and Training Committee, Air Pollution Control Association. Information from 91 schools having four year or graduate programs and five community colleges was received.Questions include type of course work, backgrounds of participating faculty and students, and eventual placement. At the present time about 70% of those in training are graduate students. It was found that most students taking initial employment in air pollution control activities had the M.S. degree. Recommendations for updating this information are made.