Behavioral and environmental determinants of personal exposures to PM2.5 in EXPOLIS – Helsinki,Finland

Behavioral and environmental determinants of PM_2.5 personal exposures were analyzed for 201 randomly selected adult participants (25–55 years old) of the EXPOLIS study in Helsinki, Finland. Personal exposure concentrations were higher than respective residential outdoor, residential indoor and workplace indoor concentrations for both smokers and non-smokers. Mean personal exposure concentrations of active smokers (31.0±31.4 μg m⁻³) were almost double those of participants exposed to environmental tobacco smoke (ETS) (16.6±11.8 μg m⁻³) and three times those of participants not exposed to tobacco smoke (9.9±6.2 μg m⁻³). Mean indoor concentrations of PM_2.5 when a member of the household smoked indoors (20.8±23.9 μg m⁻³) were approximately 2.5 times the concentrations of PM_2.5 when no smoking was reported (8.2±5.2 μg m⁻³). Interestingly, however, both mean (8.2 μg m⁻³) and median (6.9 μg m⁻³) residential indoor concentrations for non-ETS exposed participants were lower than residential outdoor concentrations (9.5 and 7.3 μg m⁻³, respectively). In simple linear regression models residential indoor concentrations were the best predictors of personal exposure concentrations. Correlations (r²) between PM_2.5 personal exposure concentrations of all participants, both smoking and non-smoking, and residential indoor, workplace indoor, residential outdoor and ambient fixed site concentrations were 0.53, 0.38, 0.17 and 0.16, respectively. Predictors for personal exposure concentrations of non-ETS exposed participants identified in multiple regression were residential indoor concentrations, workplace concentrations and traffic density in the nearest street from home, which accounted for 77% of the variance. Subsequently, step-wise regression not including residential and workplace indoor concentrations as input (as these are frequently not available), identified ambient PM_2.5 concentration and home location, as predictors of personal exposure, accounting for 47% of the variance. Ambient fixed site PM_2.5 concentrations were closely related to residential outdoor concentrations (r²=0.9, p=0.000) and PM_2.5 personal exposure concentrations were higher in summer than during other seasons. Personal exposure concentrations were significantly (p=0.040) higher for individuals living downtown compared with individuals in suburban family homes. Further analysis will focus on comparisons of determinants between Helsinki and other EXPOLIS centers.     

Microbial structure and chemical components of aerosols caused by rotating brushes in a wastewater treatment plant

Purpose

Bacterial community structure and the chemical components in aerosols caused by rotating brushes in an Orbal oxidation ditch were assessed in a Beijing municipal wastewater treatment plant.

Methods

Air samples were collected at different distances from the aerosol-generating rotating brushes. Molecular culture-independent methods were used to characterize the community structure of the airborne bacteria in each sample regardless of cell culturability. A clone library of 16S rDNA directly amplified from air DNA of each sample was constructed and sequenced to analyze the community composition and diversity. Insoluble particles and water-soluble ions emitted with microorganisms in aerosols were analysis by a scanning electron microscope together with energy dispersive X-ray spectroscopy and ion chromatogram analyzer.

Results

In total, most of the identified bacteria were Proteobacteria. The majority of sequences near the rotating brushes (the main source of the bioaerosols) were Proteobacteria (62.97 %) with ??-(18.52 %) and ??-(44.45?%) subgroups and Bacteroidetes (29.63 %). Complex patterns were observed for each sampling location, suggesting a highly diverse community structure, comparable to that found in water in the Orbal oxidation ditch. Accompany with microorganisms, 46.36???g/m³ of SO ₄ ^2? , 29.35???g/m³ of Cl^?, 21.51???g/m³ of NO ₃ ^? , 19.76???g/m³ of NH ₄ ⁺ , 11.42???g/m³ of PO ₄ ^3? , 6.18???g/m³ of NO ₂ ^? , and elements of Mg, Cl, K, Na, Fe, S, and P were detected from the air near the aerosols source.

Conclusions

Differences in the structure of the bacterial communities and chemical components in the aerosols observed between sampling sites indicated important site-related variability. The composition of microorganisms in water was one of the most important sources of bacterial communities in bioaerosols. Chemical components in bioaerosols may provide a media for airborne microorganism attachment, as well as a suitable microenvironment for their growth and survival in the air. This study will be benefit for the formulation of pollution standards, especially for aerosols, that take into account plant workers?? health.     

Carbon content of atmospheric aerosols in a residential area during the wood combustion season in Sweden

Carbonaceous aerosol particles were observed in a residential area with wood combustion during wintertime in Northern Sweden. Filter samples were analyzed for elemental carbon (EC) and organic carbon (OC) content by using a thermo-optical transmittance method. The light-absorbing carbon (LAC) content was determined by employing a commercial Aethalometer and a custom-built particle soot absorption photometer. Filter samples were used to convert the optical signals to LAC mass concentrations. Additional total PM₁₀ mass concentrations and meteorological parameters were measured. The mean and standard deviation mass concentrations were 4.4±3.6 μg m⁻³ for OC, and 1.4±1.2 μg m⁻³ for EC. On average, EC accounted for 10.7% of the total PM₁₀ and the contribution of OC to the total PM₁₀ was 35.4%. Aethalometer and custom-built PSAP measurements were highly correlated (R²=0.92). The hourly mean value of LAC mass concentration was 1.76 μg m⁻³ (median 0.88 μg m⁻³) for the winter 2005–2006. This study shows that the custom-built PSAP is a reliable alternative for the commercial Aethalometer with the advantage of being a low-cost instrument.     

Experimental evidence for a significant contribution of cellulose to indoor aerosol mass concentration

An apartment bedroom located in a residential area of Aveiro (Portugal) was selected with the aim of characterizing the cellulose content of indoor aerosol particles. Two sets of samples were taken: (1) PM₁₀ collected simultaneously in indoor and outdoor air; (2) PM₁₀ and PM_2.5 collected simultaneously in indoor air. The aerosol particles were concentrated on quartz fibre filters with low-volume samplers equipped with size selective inlets. The filters were weighed and then extracted for cellulose analysis by an enzymatic method. The average indoor cellulose concentration was 1.01 ± 0.24 μg m^?3, whereas the average outdoor cellulose concentration was 0.078 ± 0.047 μg m^?3, accounting for 4.0% and 0.4%, respectively, of the PM₁₀ mass. The corresponding average ratio between indoor and outdoor cellulose concentrations was 11.1 ± 4.9, indicating that cellulose particles were generated indoors, most likely due to the handling of cotton-made textiles as a result of routine daily activities in the bedroom. Indoor cellulose concentrations averaged 1.22 ± 0.53 μg m^?3 in the aerosol coarse fraction (determined from the difference between PM₁₀ and PM_2.5 concentrations) and averaged 0.38 ± 0.13 μg m^?3 in the aerosol fine fraction. The average ratio between the coarse and fine fractions of cellulose concentrations in the indoor air was 3.6 ± 2.1. This ratio is in line with the primary origin of this biopolymer. Results from this study provide the first experimental evidence in support of a significant contribution of cellulose to the mass of suspended particles in indoor air.     

Commuter exposure to particulate matter in public transportation modes in Hong Kong

This study examined commuter’s exposure to respirable suspended particulate matters while commuting in public transportation modes. The survey was conducted between October 1999 and January 2000 in Hong Kong. A total of eight public transportation modes, that are bus, tram, public light bus, taxi, ferry, Kowloon–Canton Railway, Mass Transit Railway and Light Rail Transit, were selected in the study. They were grouped into four categories: (T1) railway transport; (T2) non-air-conditioned roadway transport; (T3) air-conditioned roadway transport and (T4) marine transport. Both PM₁₀ and PM_2.5 levels were investigated. The results indicate that the particulate level is greatly affected by the mode of transport as well as the ventilation system of the transport. The overall average PM₁₀ concentration level in T2 (147 μg m⁻³) is the highest and is followed by T4 (81 μg m⁻³) and T3 (65 μg m⁻³). The PM₁₀ level in T1 (50 μg m⁻³) is the lowest. Notably, the commuter exposure in tram (175 μg m⁻³) is the highest among all the monitored commuting modes. Commuting modes such as railway and air-conditioned vehicle are recommended as a substitute for non-air-conditioned vehicle. The PM_2.5 to PM₁₀ ratio in transports ranged from 63% to 78%. Higher PM_2.5 to PM₁₀ ratio is found in vehicles with air-conditioning system. For the double deck vehicle, higher PM₁₀ level has resulted in the lower deck. The average upper-deck to lower-deck PM₁₀ ratio is 0.836, 0.751 and 0.738 in air-conditioned bus, non-air-conditioned bus and non-air-conditioned tram, respectively. Typical concentration profiles in different transports are also presented.     

Emissions of organophosphate and brominated flame retardants from selected consumer products and building materials

The emissions of selected flame retardants were measured in 1- and 0.02-m³ emission test chambers and 0.001-m³ emission test cells. Four product groups were of interest: insulating materials, assembly foam, upholstery/mattresses, and electronics equipment. The experiments were performed under constant environmental conditions (23°C, 50% RH) using a fixed sample surface area and controlled air flow rates. Tris (2-chloro-isopropyl)phosphate (TCPP) was observed to be one of the most commonly emitted organophosphate flame retardants in polyurethane foam applications. Depending on the sample type, area-specific emission rates (SER_a) of TCPP varied between 20 ng m⁻² h⁻¹ and 140 μg m⁻² h⁻¹.The emissions from electronic devices were measured at 60°C to simulate operating conditions. Under these conditions, unit specific emission rates (SER_u) of organophosphates were determined to be 10–85 ng unit⁻¹ h⁻¹. Increasing the temperature increased the emission of several flame retardants by up to a factor of 500. The results presented in this paper indicate that emissions of several brominated and organophosphate flame retardants are measurable. Polybrominated diphenylethers exhibited an SER_a of between 0.2 and 6.6 ng m⁻² h⁻¹ and an SER_u of between 0.6 and 14.2 ng unit⁻¹ h⁻¹. Because of sink effects, i.e., sorption to chamber components, the emission test chambers and cells used in this study have limited utility for substances low vapour pressures, especially the highly brominated compounds; hexabromocyclododecane had an SER_a of between 0.1 and 29 ng m⁻² h⁻¹ and decabromodiphenylether was not detectable at all.     

Characterization of indoor air quality and resident health in an Arizona senior housing apartment building

A survey of key indoor air quality (IAQ) parameters and resident health was carried out in 72 apartments within a single low-income senior housing building in Phoenix, Arizona. Air sampling was carried out simultaneously with a questionnaire on personal habits and general health of residents. Mean PM₁₀ concentrations are 66±16, 58±13, and 24±3 μg/m³ and mean PM_2.5 concentrations are 62±16, 53±13, and 20±2 μg/m³ for the living room, kitchen, and outdoor balcony, respectively. Median PM₁₀ concentrations are 17, 18 and 17 μg/m³ and median PM_2.5 concentrations are 13, 14, and 13 μg/m³, respectively. The initial results indicate that increased indoor particle concentrations coincide with residents who report smoking cigarettes. Indoor formaldehyde concentrations revealed median levels of 36.9, 38.8, and 4.3 ppb in the living room, kitchen, and balcony, respectively. Results show that 36% of living room samples and 44% of kitchen samples exceeded the Health Canada REL for chronic exposure to formaldehyde (40 ppb). Associations between occupants’ behavior, self-reported health conditions, and IAQ are evaluated.

Implications:This study provides a characterization of indoor air quality (IAQ) of subsidized apartments for seniors in Phoenix, Arizona. It is important for policy makers to understand the environments in which low-income seniors live, as they are vulnerable to the health impacts from poor IAQ. Formaldehyde concentrations were found to exceed the Health Canada 8-hr reference exposure level (REL) for up to 44% of indoor samples. Particulate matter exposure was governed by resident behavior (i.e., smoking). Associations between occupants’ behavior, IAQ, and self-reported health conditions are evaluated. This work can provide a foundation for subsequent remediation of IAQ conditions.     

Association of the mutagenicity of airborne particles with the direct emission from combustion processes investigated in Osaka, Japan

The association of the direct-acting mutagenicity of soluble organic fraction of airborne particles toward Salmonella typhimurium YG1024 strain with the direct emission was investigated at a roadside and at a residential area in Osaka, Japan. The direct-acting mutagenicity was evaluated as mutagenic activity per unit volume of ambient air (rev m⁻³) and/or that per airborne particulate weight collected on a filter (rev mg⁻¹). The annual or diurnal changes of the mutagenicity of airborne particles at the residential site showed similar patterns to those of some gaseous pollutants such as NO₂ and SO₂, which were emitted from combustion processes. This result indicates that the mutagenicity is mainly attributable to the primary emissions. From the analysis of the relationship between the wind sector and the mutagenic intensity, rev m⁻³ and rev mg⁻¹ values were strongly affected by the emissions from the fixed sources and from the mobile sources, respectively. The rev m⁻³ value and concentration of 1-nitropyrene (1-NP) in unit per m³ at the roadside were a factor of 2.6 and 2.8 higher than those at the residential site, respectively, but the rev mg⁻¹ value and concentration of 1-NP in unit per mg at the roadside were substantially comparable to those at the residential area. These observations suggest that the characteristics of the airborne particles can be attributed to the automotive emissions even at the suburban area.     

Personal exposures to NO2 in the EXPOLIS-study: relation to residential indoor,outdoor and workplace concentrations in Basel,Helsinki and Prague

Personal exposures, residential indoor, outdoor and workplace levels of nitrogen dioxide (NO₂) were measured for 262 urban adult (25–55 years) participants in three EXPOLIS centres (Basel; Switzerland, Helsinki; Finland, and Prague; Czech Republic) using passive samplers for 48-h sampling periods during 1996–1997. The average residential outdoor and indoor NO₂ levels were lowest in Helsinki (24±12 and 18±11 μg m⁻³, respectively), highest in Prague (61±20 and 43±23 μg m⁻³), with Basel in between (36±13 and 27±13 μg m⁻³). Average workplace NO₂ levels, however, were highest in Basel (36±24 μg m⁻³), lowest in Helsinki (27±15 μg m⁻³), with Prague in between (30±18 μg m⁻³). A time-weighted microenvironmental exposure model explained 74% of the personal NO₂ exposure variation in all centres and in average 88% of the exposures. Log-linear regression models, using residential outdoor measurements (fixed site monitoring) combined with residential and work characteristics (i.e. work location, using gas appliances and keeping windows open), explained 48% (37%) of the personal NO₂ exposure variation. Regression models based on ambient fixed site concentrations alone explained only 11–19% of personal NO₂ exposure variation. Thus, ambient fixed site monitoring alone was a poor predictor for personal NO₂ exposure variation, but adding personal questionnaire information can significantly improve the predicting power.     

A case study of potential human health impacts from petroleum coke transfer facilities

Petroleum coke or “petcoke” is a solid material created during petroleum refinement and is distributed via transfer facilities that may be located in densely populated areas. The health impacts from petcoke exposure to residents living in proximity to such facilities were evaluated for a petcoke transfer facilities located in Chicago, Illinois. Site-specific, margin of safety (MOS) and margin of exposure (MOE) analyses were conducted using estimated airborne and dermal exposures. The exposure assessment was based on a combined measurement and modeling program that included multiyear on-site air monitoring, air dispersion modeling, and analyses of soil and surfaces in residential areas adjacent to two petcoke transfer facilities located in industrial areas. Airborne particulate matter less than 10 microns (PM₁₀) were used as a marker for petcoke. Based on daily fence line monitoring, the average daily PM₁₀ concentration at the KCBX Terminals measured on-site was 32 μg/m³, with 89% of 24-hr average PM₁₀ concentrations below 50 μg/m³ and 99% below 100 μg/m³. A dispersion model estimated that the emission sources at the KCBX Terminals produced peak PM₁₀ levels attributed to the petcoke facility at the most highly impacted residence of 11 μg/m³ on an annual average basis and 54 μg/m³ on 24-hr average basis. Chemical indicators of petcoke in soil and surface samples collected from residential neighborhoods adjacent to the facilities were equivalent to levels in corresponding samples collected at reference locations elsewhere in Chicago, a finding that is consistent with limited potential for off-site exposure indicated by the fence line monitoring and air dispersion modeling. The MOE based upon dispersion model estimates ranged from 800 to 900 for potential inhalation, the primary route of concern for particulate matter. This indicates a low likelihood of adverse health effects in the surrounding community.?Implications: Handling of petroleum coke at bulk material transfer facilities has been identified as a concern for the public health of surrounding populations. The current assessment, based on measurements and modeling of two facilities located in a densely populated urban area, indicates that petcoke transport and accumulation in off-site locations is minimal. In addition, estimated human exposures, if any, are well below levels that could be anticipated to produce adverse health effects in the general population.     

Air quality measurements in urban green areas – a case study

The influence of traffic-induced pollutants (e.g. CO, NO, NO₂ and O₃) on the air quality of urban areas was investigated in the city of Essen, North Rhine-Westphalia (NRW), Germany. Twelve air hygiene profile measuring trips were made to analyse the trace gas distribution in the urban area with high spatial resolution and to compare the air hygiene situation of urban green areas with the overall situation of urban pollution. Seventeen measurements were made to determine the diurnal concentration courses within urban parks (summer conditions: 13 measurements, 530 30 min mean values, winter conditions: 4 measurements, 128 30 min mean values). The measurements were carried out during mainly calm wind and cloudless conditions between February 1995 and March 1996. It was possible to establish highly differentiated spatial concentration patterns within the urban area. These patterns were correlated with five general types of land use (motorway, main road, secondary road, residential area, green area) which were influenced to varying degrees by traffic emissions. Urban parks downwind from the main emission sources show the following typical temporal concentration courses: In summer rush-hour-dependent CO, NO and NO₂ maxima only occurred in the morning. A high NO₂/NO ratio was established during weather conditions with high global radiation intensities (K>800 W m⁻²), which may result in a high O₃ formation potential. Some of the values measured found in one of the parks investigated (Gruga Park, Essen, area: 0.7 km²), which were as high as 275 μg m⁻³ O₃ (30-min mean value) were significantly higher than the German air quality standard of 120 μg m⁻³ (30-min mean value, VDI Guideline 2310, 1996) which currently applies in Germany and about 20% above the maximum values measured on the same day by the network of the North Rhine–Westphalian State Environment Agency. In winter high CO and NO concentrations occur in the morning and during the afternoon rush-hour. The highest concentrations (CO=4.3 mg m⁻³, NO=368 μg m⁻³, 30-min mean values) coincide with the increase in the evening inversion. The maximum measured values for CO, NO and NO₂ do not, however, exceed the German air quality standards in winter and summer.     

Construction and Economics of a Pilot/Full-Scale Biological Trickling Filter Reactor for the Removal of Volatile Organic Compounds from Polluted Air

ABSTRACT

The design and the construction of an actual 8.7-m³ pilot/ full-scale biotrickling filter for waste air treatment is described and compared with a previous conceptual scale-up of a laboratory reactor. The reactor construction costs are detailed and show that about one-half of the total reactor costs ($97,000 out of $178,000) was for personnel and engineering time, whereas ~20% was for monitoring and control equipment. A detailed treatment cost analysis demonstrated that, for an empty bed contact time of 90 sec, the overall treatment costs (including capital charges) were as low as $8.7/1000 m³ _air in the case where a nonchlorinated volatile organic compound (VOC) was treated, and $14/ 1000 m³ _air for chlorinated compounds such as CH₂Cl₂. Comparison of these costs with conventional air pollution control techniques demonstrates excellent perspectives for more field applications of biotrickling filters. As the specific costs of building and operating biotrickling filter reactors decrease with increasing size of the reactor, the cost benefit of biotrickling filtration is expected to increase for full technical-scale bioreactors.     

Concentration-dependent NH3 deposition processes for mixed moorland semi-natural vegetation

Dry deposition modelling typically assumes that canopy resistance (R_c) is independent of ammonia (NH₃) concentration. An innovative flux chamber system was used to provide accurate continuous measurements of NH₃ deposition to a moorland composed of a mixture of Calluna vulgaris (L.) Hull, Eriophorum vaginatum L. and Sphagnum spp. Ammonia was applied at a wide range of concentrations (1–100 μg m⁻³). The physical and environmental properties and the testing of the chamber are described, as well as results for the moorland vegetation using the ‘canopy resistance’ and ‘canopy compensation point’ interpretations of the data.Results for moorland plant species demonstrate that NH₃ concentration directly affects the rate of NH₃ deposition to the vegetation canopy, with R_c and cuticular resistance (R_w) increasing with increasing NH₃ concentrations. Differences in R_c were found between night and day: during the night R_c increases from 17 s m⁻¹ at 10 μg m⁻³ to 95 s m⁻¹ at 80 μg m⁻³, whereas during the day R_c increases from 17 s m⁻¹ at 10 μg m⁻³ to 48 s m⁻¹ at 80 μg m⁻³. The lower resistance during the day is caused by the stomata being open and available as a deposition route to the plant. R_w increased with increasing NH₃ concentrations and was not significantly different between day and night (at 80 μg m⁻³ NH₃ day R_w=88 s m⁻¹ and night R_w=95 s m⁻¹). The results demonstrate that assessments using fixed R_c will over-estimate NH₃ deposition at high concentrations (over ∼15 μg m⁻³).     

ANAMMOX与反硝化协同作用及氮素负荷研究

向成功启动并稳定运行630 d后的UASB生物膜反应器系统连续添加有机物,分析其对厌氧氨氧化反应脱氮效果的影响,并进行氮素浓度负荷试验.在厌氧氨氧化反应器系统中连续投加有机COD(葡萄糖),系统运行稳定,有机COD(葡萄糖)存在对系统去除氮素能力影响不大,有机COD去除率达到92.0%,仅用23 d,在同一反应器系统中成功实现了厌氧氨氧化与反硝化协同作用脱氮.氮素浓度负荷试验阶段,进水氨氮(NH 4-N)、亚硝氮(NO-2-N)以及总氮(TN)浓度负荷分别从0.063 kg/(m3·d)和0.063 kg/(m3·d)和0.126 kg/(m3·d)提升到了0.239 kg/(m3·d)、0.315 kg/(m3·d)和0.554 kg/(m3·d),相应去除率分别为84.0%、93.0%和85.0%,厌氧氨氧化工艺的UASB生物膜反应器对氮素浓度负荷仍有很大提升空间.     

Natural chloroform emissions from the blanket peat bogs in the vicinity of Mace Head,Ireland over a 14-year period

Simultaneous chloroform (CHCl₃) emission and ozone (O₃) deposition are regularly observed under nocturnal inversions during the summer months from and to the peat bogs in the vicinity of the Mace Head Atmospheric Research Station, Connemara, Co Galway, Ireland. Emissions were estimated using the nocturnal box model applied to routine atmospheric observations collected over a 14-year period from 1995 to 2008. Strict criteria were applied in the selection of events of low wind speed, under a stable night-time inversion layer in baseline air conditions, with no transport from Europe. The mean peatland CHCl₃ flux was 2.91 μg m^?2 h^?1 with highly variable fluxes ranging from 0.44 to 12.94 μg m^?2 h^?1. These fluxes are generally larger than those reported previously for similar biomes and if representative would make a significant contribution to the global estimated source of CHCl₃. Fluxes were not strongly correlated with either atmospheric temperature or the level of precipitation. Over the 14-year period there appears to have been a small increase in overall CHCl₃ emissions, although we stress that the nocturnal box model has a number of limitations and assumptions which should be taken into account.     

Carbon dioxide fluxes over an urban park area

From September 2006 to October 2007 turbulent fluxes of carbon dioxide were measured at an urban tower station (26 m above ground level, z/z_h = 1.73) in Essen, Germany, using the eddy covariance technique. The site was located at the border between a public park area (70 ha) in the south–west of the station and suburban/urban residential as well as light commercial areas in the north and east of the tower. Depending on the land-use two different sectors (park and urban) were identified showing distinct differences in the temporal evolution of the surface-atmosphere exchange of CO₂. While urban fluxes appear to be governed by anthropogenic emissions from domestic heating and traffic (average flux 9.3 μmol m^?2 s^?1), the exchange of CO₂ was steered by biological processes when the park contributed to the flux footprint. The diurnal course during the vegetation period exhibited negative daytime fluxes up to ?10 μmol m^?2 s^?1 on average in summer. Nevertheless, with a mean of 0.8 μmol m^?2 s^?1 park sector fluxes were slightly positive, thus no net carbon uptake by the surface occurred throughout the year.In order to sum the transport of CO₂ a gap-filling procedure was performed by means of artificial neural network generalisation. Using additional meteorological inputs the daily exchange of CO₂ was reproduced using radial basis function networks (RBF). The resulting yearly sum of 6031 g m^?2 a^?1 indicates the entire study site to be a considerable source of CO₂.     

Performance of an Innovative Two-Stage Process Converting Food Waste to Hydrogen and Methane

Abstract

This study was conducted to evaluate the performance of an innovative two-stage process, BIOCELL, that was developed to produce hydrogen (H₂) and methane (CH₄) from food waste on the basis of phase separation, reactor rotation mode, and sequential batch technique. The BIOCELL process consisted of four leaching-bed reactors for H₂ recovery and post-treatment and a UASB reactor for CH₄ recovery. The leaching-bed reactors were operated in a rotation mode with a 2-day interval between degradation stages. The sequential batch technique was useful to optimize environmental conditions during H₂ fermentation. The BIOCELL process demonstrated that, at the high volatile solids (VS) loading rate of 11.9 kg/m³-day, it could remove 72.5% of VS and convert VS_removed to H₂ (28.2%) and CH₄ (69.9%) on a chemical oxygen demand (COD) basis in 8 days. H₂ gas production rate was 3.63 m³/m³ ·day, while CH₄ gas production rate was 1.75 m³/m³ ·day. The yield values of H₂ and CH₄ were 0.31 and 0.21 m³/kg VS_added, respectively. Moreover, the output from the post-treatment could be used as a soil amendment. The BIOCELL process proved to be stable, reliable, and effective in resource recovery as well as waste stabilization.     

Growing season methane budget of an Inner Mongolian steppe

We present a methane (CH₄) budget for the area of the Baiyinxile Livestock Farm, which comprises approximately 1/3 of the Xilin river catchment in central Inner Mongolia, P.R. China. The budget calculations comprise the contributions of natural sources and sinks as well as sources related to the main land-use in this region (non-nomadic pastoralism) during the growing season (May–September). We identified as important CH₄ sources floodplains (mean 1.55 ± 0.97 mg CH₄–C m^?2 h^?1) and domestic ruminants, which are mainly sheep in this area. Within the floodplain significant differences between investigated positions were detected, whereby only positions close-by the river or bayous emitted large amounts of CH₄ (mean up to 6.21 ± 1.83 mg CH₄–C m^?2 h^?1). Further CH₄ sources were sheepfolds (0.08–0.91 mg CH₄–C m^?2 h^?1) and pasture faeces (1.34 ± 0.22 mg CH₄–C g^?1 faeces dry weight), but they did not play a significant role for the CH₄ budget. In contrast, dung heaps were not a net source of CH₄ (0.0 ± 0.2 for an old and 0.0 ± 0.3 μg CH₄–C kg^?1 h^?1 for a new dung heap). Trace gas measurements along two landscape transects (volcano, hill slope) revealed expectedly a mean CH₄ uptake (volcano: 76.5 ± 4.3; hill: 28.3 ± 5.3 μg CH₄–C m^?2 h^?1), which is typical for the aerobic soils in this and other steppe ecosystems. The observed fluxes were rarely influenced by topography.The CH₄ emissions from the floodplain and the sheep were not compensated by the CH₄ oxidation of aerobic steppe soils and thus, this managed semi-arid grassland did not serve as a terrestrial sink, but as a source for this globally important greenhouse gas. The source strength amounted to 1.5–3.6 kg CH₄–C ha^?1 during the growing season, corresponding to 3.5–8.7 kg C ha^?1 yr^?1.     

Ammonia concentrations and fluxes over a forest in the midwestern USA

We present measurements of ammonia (NH₃) over a deciduous forest in southern Indiana collected during four field campaigns; two in the spring during the transition to leaf-out and two during the winter. Above canopy NH₃ concentrations measured continuously using two Wet Effluent Diffusion Denuders indicate mean concentrations of 0.6–1.2 μg m⁻³ during the spring and 0.3 μg m⁻³ during the winter. Measurements suggest that on average the forest act as a sink of NH₃, with a representative daily deposition flux of 1.8 mg-NH₃ m⁻² during the spring. However, on some days during the spring inverted concentration gradients of NH₃ were observed resulting in an apparent upward flux of nearly 0.2 mg-NH₃ m⁻² h⁻¹. Analyses suggest that this apparent emission flux may be due to canopy emission but evaporation of ammonium nitrate particles may also be partly responsible for the observed inverted concentration gradients.     

Biogenic emission of dimethylsulfide (DMS) from the North Yellow Sea,China and its contribution to sulfate in aerosol during summer

Seawater, atmospheric dimethylsulfide (DMS) and aerosol compounds, potentially linked with DMS oxidation, such as methanesulfonic acid (MSA) and non-sea-salt sulfate (nss-SO₄^2?) were determined in the North Yellow Sea, China during July–August, 2006. The concentrations of seawater and atmospheric DMS ranged from 2.01 to 11.79 nmol l^?1 and from 1.68 to 8.26 nmol m^?3, with average values of 6.20 nmol l^?1 and 5.01 nmol m^?3, respectively. Owing to the appreciable concentration gradient, DMS accumulated in the surface water was transferred into the atmosphere, leading to a net sea-to-air flux of 6.87 μmol m^?2 d^?1 during summer. In the surface seawater, high DMS values corresponded well with the concurrent increases in chlorophyll a levels and a significant correlation was observed between integrated DMS and chlorophyll a concentrations. In addition, the concentrations of MSA and nss-SO₄^2? measured in the aerosol samples ranged from 0.012 to 0.079 μg m^?3 and from 3.82 to 11.72 μg m^?3, with average values of 0.039 and 7.40 μg m^?3, respectively. Based on the observed MSA, nss-SO₄^2? and their ratio, the relative biogenic sulfur contribution was estimated to range from 1.2% to 11.5%, implying the major contribution of anthropogenic source to sulfur budget in the study area.