One-at-a-time sensitivity analysis of pollutant loadings to subsurface properties for the assessment of soil and groundwater pollution potential

Chemical leak was numerically simulated for four chemical substances: benzene (light non-aqueous phase liquid (NAPL)), tetrachloroethylene (dense NAPL), phenol (soluble in water), and pentachlorophenol (white crystalline solid) in a hypothetical subsurface leak situation using a multiphase compositional transport model. One metric ton of chemical substances was assumed to leak at a point 3.51 m above the water table in a homogeneous unconfined aquifer which had the depth to water table of 7.135 m, the hydraulic gradient of 0.00097, the recharge rate of 0.7 mm/day, and the permeability of 2.92?×?10^?10 m². For comparison, surface spill scenarios, which had a long pathway from source to the water table, were simulated. Using the model results, point-source pollutant loadings to soil and groundwater were calculated by multiplying mass, impact area, and duration above and below the water table respectively. Their sensitivity to subsurface properties (depth to water table, recharge rate, porosity, organic carbon content, decay rate, hydraulic gradient, capillary pressure, relative permeability, permeability) was analyzed, with changing each parameter within acceptable ranges. The study result showed that the pollutant loading to groundwater was more sensitive to the subsurface properties than the pollutant loading to soil. Decay rate, groundwater depth, hydraulic gradient and porosity were influential to pollutant loadings. The impact of influential parameters on pollutant loadings was nonlinear. The dominant subsurface properties of pollution loadings (e.g., decay rate, groundwater depth, hydraulic gradient, and porosity for groundwater) also affect the vulnerability, and the subsurface pollutant loadings defined in this study are dependent on chemical properties as well, which indicates that the influential hydrogeological and physicochemical parameters to pollutant loadings can be used for pollution potential assessment. The contribution of this work is the suggestion that the sensitivity of pollutant loadings can be used for pollution potential assessment. Soil and groundwater pollution potential of chemicals are discussed altogether for leak scenarios. A physics-based model is used to understand the impact of subsurface properties on the fate and transport of chemicals above and below the water table, and consequently their impact on the pollutant loading to soil and groundwater.

     

Factors controlling groundwater quality in the Yeonjegu District of Busan City,Korea, using the hydrogeochemical processes and fuzzy GIS

The hydrogeochemical processes and fuzzy GIS techniques were used to evaluate the groundwater quality in the Yeonjegu district of Busan Metropolitan City, Korea. The highest concentrations of major ions were mainly related to the local geology. The seawater intrusion into the river water and municipal contaminants were secondary contamination sources of groundwater in the study area. Factor analysis represented the contamination sources of the mineral dissolution of the host rocks and domestic influences. The Gibbs plot exhibited that the major ions were derived from the rock weathering condition. Piper’s trilinear diagram showed that the groundwater quality was classified into five types of CaHCO₃, NaHCO₃, NaCl, CaCl₂, and CaSO₄ types in that order. The ionic relationship and the saturation mineral index of the ions indicated that the evaporation, dissolution, and precipitation processes controlled the groundwater chemistry. The fuzzy GIS map showed that highly contaminated groundwater occurred in the northeastern and the central parts and that the groundwater of medium quality appeared in most parts of the study area. It suggested that the groundwater quality of the study area was influenced by local geology, seawater intrusion, and municipal contaminants. This research clearly demonstrated that the geochemical analyses and fuzzy GIS method were very useful to identify the contaminant sources and the location of good groundwater quality.

     

The influence of colloid formation in a granite groundwater bentonite porewater mixing zone on radionuclide speciation

In the context of deep geological storage of high level nuclear waste the repository will be designed as multiple barrier system including bentonite as buffer/backfill material and the host rock formation as geological barrier. The engineered barrier (bentonite) will be in contact with the host rock formation and consequently it can be expected that bentonite porewater will mix with formation groundwater. We simulate in this study the mixing of Grimsel groundwater (glacial melt water) with synthetic Febex porewater (assuming already saturated state) in a batch-type study and investigate the formation of colloids by laser-induced breakdown detection (LIBD) and SEM-EDX as well as the changes in radionuclide (U, Th, Eu) speciation via ultrafiltration or via time-resolved laser fluorescence spectroscopy (TRLFS) analysis in the case of Cm(III). Based on PHREEQC saturation index (SI) calculations a precipitation of calcite might be expected at low Febex porewater (FPW) content (< 20%), fluorite precipitation at FPW contents < 60% and gibbsite precipitation at FPW contents above 10%. The colloids generated in the mixing zone aggregate when the synthetic FPW content exceeds 10%. LIBD analysis of the time-dependent colloid generation/aggregation revealed a low concentration of colloids to be stable with an estimated plateau value around 100–200 ppt and an average colloid diameter around 30 nm after 140 days reaction time at FPW admixture > 10%. SEM/EDX mostly identifies Al/Si containing colloidal phases and some sulfates could be found under certain admixture ratios. TRLFS studies show that the Cm speciation is strongly influenced by colloid formation in all solutions. In the Febex pore water/GGW mixing zone with high groundwater contents (> 80%) colloids are newly formed and Cm is almost quantitatively associated with most likely polysilicilic acid colloids.     

Long-term geochemical evolution of the near field repository: insights from reactive transport modelling and experimental evidences

The KBS-3 underground nuclear waste repository concept designed by the Swedish Nuclear Fuel and Waste Management Co. (SKB) includes a bentonite buffer barrier surrounding the copper canisters and the iron insert where spent nuclear fuel will be placed. Bentonite is also part of the backfill material used to seal the access and deposition tunnels of the repository. The bentonite barrier has three main safety functions: to ensure the physical stability of the canister, to retard the intrusion of groundwater to the canisters, and in case of canister failure, to retard the migration of radionuclides to the geosphere. Laboratory experiments (< 10 years long) have provided evidence of the control exerted by accessory minerals and clay surfaces on the pore water chemistry. The evolution of the pore water chemistry will be a primordial factor on the long-term stability of the bentonite barrier, which is a key issue in the safety assessments of the KBS-3 concept.In this work we aim to study the long-term geochemical evolution of bentonite and its pore water in the evolving geochemical environment due to climate change. In order to do this, reactive transport simulations are used to predict the interaction between groundwater and bentonite which is simulated following two different pathways: (1) groundwater flow through the backfill in the deposition tunnels, eventually reaching the top of the deposition hole, and (2) direct connection between groundwater and bentonite rings through fractures in the granite crosscutting the deposition hole. The influence of changes in climate has been tested using three different waters interacting with the bentonite: present-day groundwater, water derived from ice melting, and deep-seated brine. Two commercial bentonites have been considered as buffer material, MX-80 and Deponit CA-N, and one natural clay (Friedland type) for the backfill. They show differences in the composition of the exchangeable cations and in the accessory mineral content. Results from the simulations indicate that pore water chemistry is controlled by the equilibrium with the accessory minerals, especially carbonates. pH is buffered by precipitation/dissolution of calcite and dolomite, when present. The equilibrium of these minerals is deeply influenced by gypsum dissolution and cation exchange reactions in the smectite interlayer. If carbonate minerals are initially absent in bentonite, pH is then controlled by surface acidity reactions in the hydroxyl groups at the edge sites of the clay fraction, although its buffering capacity is not as strong as the equilibrium with carbonate minerals. The redox capacity of the bentonite pore water system is mainly controlled by Fe(II)-bearing minerals (pyrite and siderite). Changes in the groundwater composition lead to variations in the cation exchange occupancy, and dissolution–precipitation of carbonate minerals and gypsum. The most significant changes in the evolution of the system are predicted when ice-melting water, which is highly diluted and alkaline, enters into the system. In this case, the dissolution of carbonate minerals is enhanced, increasing pH in the bentonite pore water. Moreover, a rapid change in the population of exchange sites in the smectite is expected due to the replacement of Na for Ca.     

Geochemical characterization of acid mine drainage from a waste rock pile, Mine Doyon, Québec, Canada

Water quality in the unsaturated and saturated zones of a waste rock pile containing sulphides was investigated. The main objectives of the project were (1) the evaluation of geochemical trends including the acid mine drainage (AMD)-buffering mechanism and the role of secondary minerals, and (2) the investigation of the use of stable isotopes for the interpretation of physical and geochemical processes in waste rock. Pore water in unsaturated zone was sampled from suction lysimeters and with piezometers in underlying saturated rocks. The investigation revealed strong temporal (dry period vs. recharge period), and spatial (slope vs. central region of pile) variability in the formation of acid mine drainage. The main secondary minerals observed were gypsum and jarosite. There was a higher concentration of gypsum in solid phase at Site TBT than at Site 6, suggesting that part of the gypsum formed at Site 6 in the early stage of AMD has been already dissolved. Formation of secondary minerals contributed to the formation of AMD by opening of foliation planes in waste rock, thus increasing the access of oxidants like O2 and Fe3+ to previously encapsulated pyrite. The behavior of several dissolved species such as Mg, Al, and Fe2+ can be considered as conservative in the leachate. Stable isotopes, deuterium and 18O, indicated internal evaporation within the pile, and were used to trace recharge pulses from snowmelt. Isotope trends for 34S and 18O(SO4) indicated a lack of sulfate reduction and zones of active oxidation of pyrite, respectively. Results of numerical modeling of pyrite oxidation and gas and water transport were consistent with geochemical and isotopic trends and confirmed zones of high evaporation rate within the rock pile close to the slope. The results indicate that physical and chemical processes within the pile are strongly coupled and cannot be considered separately when oxidation rates are high and influence gas transport as a result of heat generation.     

Analysis of a deep well recharge experiment by calibrating a reactive transport model with field data

This paper describes the modeling of the hydrogeochemical effects of deep well recharge of oxic water into an anoxic pyrite-bearing aquifer. Kinetic expressions have been used for mineral dissolution-precipitation rates and organic matter oxidation. Hydrological and chemical parameters of the model were calibrated to field measurements. The results showed that oxidation of pyrite (FeS(2)) and, to a lesser extent, organic matter dominate the changes in quality of the recharged water during its passage through the aquifer. The recharge leads to the consumption of oxygen and nitrate and the formation of sulfate and ferrihydrite. Complexation reactions, cation exchange and precipitation and dissolution of calcite, siderite and rhodochrosite were also identified through the modeling. Despite problems of non-uniqueness of the calibrated parameters, the model was used successfully to depict the geochemical processes occurring in the aquifer. Non-uniqueness can be avoided by constraining the model as much as possible to measurements and/or data from literature, although they cannot be considered always as fixed values and should be considered as stochastic variables instead.     

Modelling reactions between cement pore fluids and rock: implications for porosity change

The migration of groundwater equilibrated with cement from a deep geological disposal facility for radioactive wastes will perturb the chemical, minerological and physical properties of the geosphere in advance of the migration of radionuclides. Preliminary modelling of a simplified scenario has been conducted to assess these changes using appropriate data for mineral dissolution kinetics, the chemical composition of cement pore fluids, and the hydrogeological characteristics of fractured crystalline rock. Chemical exchanges between rock immediately adjacent to the engineered barriers of a waste disposal facility and pore fluids were evaluated using the speciation-reaction path code. which revealed rapid loss of Ca, and gains in Na and Si of the evolved fluids, with little change in pH. Secondary minerals show a sequence of calcium silicate hydrates, and zeolites. Precise definition of the overall mass balance is uncertain due to the absence of both thermodynamic data for many zeolites and kinetic data for the precipitation of feldspars. Modelling has demonstrated that reaction kinetics will be important in governing chemical exchanges for length scales up to 20 m. Radionuclide retardation will be enhanced by the growth of zeolites and calcium silicate hydrates.     

Chemical modifications of groundwater contaminated by recharge of treated sewage effluent

Long-term monitoring of the chemical composition of recharge sewage effluent and associated contaminated groundwater from the Dan Region Sewage Reclamation Project shows, after 16 years of recharge operation, the presence of a distinct saline plume (up to 400 mg/l Cl), extending 1600 m downgradient in the Coastal Plain aquifer of Israel. The recorded electrolyte composition of groundwater in the vicinity of the recharge area reflects the variations in the compositions of the sewage effluents, as well as water-rock interactions induced by the recharge of treated sewage effluents. The original sewage composition was modified, particularly during early stages of effluent migration in the unsaturated zone, by cation-exchange and adsorption reactions. Since the soil sorption capacity is finite these reactions caused only limited modifications, and once the system reached a steady state the inorganic composition of the contaminated groundwater became similar to that of the recharge water. Decomposition of organic matter in the unsaturated zone resulted in CO₂ generation and dissolution of CaCO₃ minerals in the aquifer. It was shown that chemical and/or bio-degradation of organic matter takes place mainly in the unsaturated (vadose) zone. Hence, monitoring the efficiency of the vadose zone to retain contaminants is essential for evaluating the quality of groundwater since it was shown that organic compounds behave almost conservatively once the effluents enter and flow within the saturated zone.     

Large-scale modeling of reactive solute transport in fracture zones of granitic bedrocks

Final disposal of high-level radioactive waste in deep repositories located in fractured granite formations is being considered by several countries. The assessment of the safety of such repositories requires using numerical models of groundwater flow, solute transport and chemical processes. These models are being developed from data and knowledge gained from in situ experiments such as the Redox Zone Experiment carried out at the underground laboratory of Äspö in Sweden. This experiment aimed at evaluating the effects of the construction of the access tunnel on the hydrogeological and hydrochemical conditions of a fracture zone intersected by the tunnel. Most chemical species showed dilution trends except for bicarbonate and sulphate which unexpectedly increased with time. Molinero and Samper [Molinero, J. and Samper, J. Groundwater flow and solute transport in fracture zones: an improved model for a large-scale field experiment at Äspö (Sweden). J. Hydraul. Res., 42, Extra Issue, 157–172] presented a two-dimensional water flow and solute transport finite element model which reproduced measured drawdowns and dilution curves of conservative species. Here we extend their model by using a reactive transport which accounts for aqueous complexation, acid–base, redox processes, dissolution–precipitation of calcite, quartz, hematite and pyrite, and cation exchange between Na⁺ and Ca²⁺. The model provides field-scale estimates of cation exchange capacity of the fracture zone and redox potential of groundwater recharge. It serves also to identify the mineral phases controlling the solubility of iron. In addition, the model is useful to test the relevance of several geochemical processes. Model results rule out calcite dissolution as the process causing the increase in bicarbonate concentration and reject the following possible sources of sulphate: (1) pyrite dissolution, (2) leaching of alkaline sulphate-rich waters from a nearby rock landfill and (3) dissolution of iron monosulphides contained in Baltic seafloor sediments. Based on these results, microbially mediated processes are postulated as the most likely hypothesis to explain the measured increase of dissolved bicarbonates and sulphates after tunnel construction.     

Fluoride in weathered rock aquifers of southern India: Managed Aquifer Recharge for mitigation

Climatic condition, geology, and geochemical processes in an area play a major role on groundwater quality. Impact of these on the fluoride content of groundwater was studied in three regions—part of Nalgonda district in Telangana, Pambar River basin, and Vaniyar River basin in Tamil Nadu, southern India, which experience semi-arid climate and are predominantly made of Precambrian rocks. High concentration of fluoride in groundwater above 4 mg/l was recorded. Human exposure dose for fluoride through groundwater was higher in Nalgonda than the other areas. With evaporation and rainfall being one of the major contributors for high fluoride apart from the weathering of fluoride rich minerals from rocks, the effect of increase in groundwater level on fluoride concentration was studied. This study reveals that groundwater in shallow environment of all three regions shows dilution effect due to rainfall recharge. Suitable managed aquifer recharge (MAR) methods can be adopted to dilute the fluoride rich groundwater in such regions which is explained with two case studies. However, in deep groundwater, increase in fluoride concentration with increase in groundwater level due to leaching of fluoride rich salts from the unsaturated zone was observed. Occurrence of fluoride above 1.5 mg/l was more in areas with deeper groundwater environment. Hence, practicing MAR in these regions will increase the fluoride content in groundwater and so physical or chemical treatment has to be adopted. This study brought out the fact that MAR cannot be practiced in all regions for dilution of ions in groundwater and that it is essential to analyze the fluctuation in groundwater level and the fluoride content before suggesting it as a suitable solution. Also, this study emphasizes that long-term monitoring of these factors is an important criterion for choosing the recharge areas.     

地衣对建筑物的生物破坏作用

大量的证据表明地衣可以诱发和加速矿质基质的物理、化学风化过程,着生于建筑物表面的地衣能对建筑材料导致明显的生物破坏.其中,地衣菌丝在矿质基质中的穿插生长、原植体随环境变化表现出的膨胀收缩、冻融交替等机制对建筑物造成机械破坏.而地衣分泌的草酸等简单有机酸以及大量的高分子有机化合物诱发和促进矿质基质的生物-化学风化过程.受其影响,矿质建材中原生矿物遭受溶解、蚀变,并产生多种次生矿物.最终破坏建筑物的坚固程度、缩短其使用寿命、减低其美学价值.     

Geochemical evaluation of different groundwater–host rock systems for radioactive waste disposal

The geochemical suitability of a deep bedrock repository for radioactive waste disposal is determined by the composition of geomatrix and groundwater. Both influence radionuclide solubility, chemical buffer capacity and radionuclide retention. They also determine the chemical compatibility of waste forms, containers and backfill materials. Evaluation of different groundwater–host rock systems is performed by modeling the geochemical environments and the resulting radionuclide concentrations. In order to demonstrate the evaluation method, model calculations are applied to data sets available for various geological formations such as granite, clay and rocksalt.The saturation state of the groundwater–geomatrix system is found to be fundamental for the evaluation process. Hence, calculations are performed to determine if groundwater is in equilibrium with mineral phases of the geological formation. In addition, corrosion of waste forms in different groundwater is examined by means of reaction path modeling. The corrosion reactions change the solution compositions and pH, resulting in significant changes of radionuclide solubilities. The results demonstrate that geochemical modeling of saturation state and compatibility of the host formation environment with the radioactive waste proves to be a feasible tool for evaluation of various sites considered as deep underground repositories.     

Assessing the chemical behavior and spatial distribution of yttrium and rare earth elements (YREEs) in a coastal aquifer adjacent to the Urmia Hypersaline Lake,NW Iran

This study aims to shed light on the seasonal behavior of yttrium and rare earth elements (YREEs) in the Urmia Aquifer (UA), in the immediate vicinity of Urmia Lake (UL) in Iran. Samples of groundwater, collected under dry and wet conditions in coastal wells of UA, suggest a large degree of variability in both YREE abundance and normalized patterns. Although weathering or water-rock interactions (between the surface/groundwater and rock samples) were predicted to be the most probable source in explaining YREEs in groundwater samples, results to the contrary indicate that the groundwater do not inherit aquifer rock-like YREE signatures in the study area; this might be due to the relative stability of YREEs during the process of water-rock interactions, which suggest that methods based on YREEs can be beneficial in discrimination of water sources. Furthermore, findings demonstrated no significant relationship between Ce/Ce* and salinity (0.08 and 0.05 in wet and dry seasons, respectively), and between Eu/Eu* and salinity (0.1 and ?0.04 in wet and dry seasons, respectively). Dissimilarity of patterns of YREEs in rock and water samples reveals YREEs as no conservative tracers in determining the UL saltwater intrusion into coastal groundwater. Therefore, the groundwater YREE concentrations and fractionation patterns in UA warrant controlling by coastal aquifer need to be controlled by other chemical weathering, adsorption, desorption, and solution complexation reactions. Finally, comparison of REE concentration values in groundwater samples with corresponding indicative admissible drinking water concentrations (IAC) demonstrated their suitability for drinking purposes.

     

Geochemical evaluation of different groundwater-host rock systems for radioactive waste disposal

The geochemical suitability of a deep bedrock repository for radioactive waste disposal is determined by the composition of geomatrix and groundwater. Both influence radionuclide solubility, chemical buffer capacity and radionuclide retention. They also determine the chemical compatibility of waste forms, containers and backfill materials. Evaluation of different groundwater-host rock systems is performed by modeling the geochemical environments and the resulting radionuclide concentrations. In order to demonstrate the evaluation method, model calculations are applied to data sets available for various geological formations such as granite, clay and rocksalt. The saturation state of the groundwater-geomatrix system is found to be fundamental for the evaluation process. Hence, calculations are performed to determine if groundwater is in equilibrium with mineral phases of the geological formation. In addition, corrosion of waste forms in different groundwater is examined by means of reaction path modeling. The corrosion reactions change the solution compositions and pH, resulting in significant changes of radionuclide solubilities. The results demonstrate that geochemical modeling of saturation state and compatibility of the host formation environment with the radioactive waste proves to be a feasible tool for evaluation of various sites considered as deep underground repositories.     

Modelling the geochemical fate and transport of wastewater-derived phosphorus in contrasting groundwater systems

A 1D reactive transport model (RTM) is used to obtain a mechanistic understanding of the fate of phosphorus (P) in the saturated zone of two contrasting aquifer systems. We use the field data from two oxic, electron donor-poor, wastewater-impacted, sandy Canadian aquifers, (Cambridge and Muskoka sites) as an example of a calcareous and non-calcareous groundwater system, respectively, to validate our reaction network. After approximately 10 years of wastewater infiltration, P is effectively attenuated within the first 10 m down-gradient of the source mainly through fast sorption onto calcite and Fe oxides. Slow, kinetic sorption contributes further to P removal, while precipitation of phosphate minerals (strengite, hydroxyapatite) is quantitatively unimportant in the saturated zone. Nitrogen (N) dynamics are also considered, but nitrate behaves essentially as a conservative tracer in both systems. The model-predicted advancement of the P plume upon continued wastewater discharge at the calcareous site is in line with field observations. Model results suggest that, upon removal of the wastewater source, the P plume at both sites will persist for at least 20 years, owing to desorption of P from aquifer solids and the slow rate of P mineral precipitation. Sensitivity analyses for the non-calcareous scenario (Muskoka) illustrate the importance of the sorption capacity of the aquifer solids for P in modulating groundwater N:P ratios in oxic groundwater. The model simulations predict the breakthrough of groundwater with high P concentrations and low N:P ratios after 17 years at 20 m from the source for an aquifer with low sorption capacity (<0.02% w/w Fe(OH)(3)). In this type of system, denitrification plays a minor role in lowering the N:P ratios because it is limited by the availability of labile dissolved organic matter.     

Arsenic distribution and pathway scenarios for sediments and water in a peri-urban Mongolian small-scale coal mining area (Nalaikh District,Ulaanbaatar)

The distribution of arsenic (As) in environmental compartments is investigated in the Nalaikh Depression of N-Mongolia. In Nalaikh, lignite coal is mined by artisanal small-scale mining (ASM) approaches. Because As is often associated with sulfuric minerals in coal, it was hypothesized that enrichment of As is related to coal ASM. A second hypothesis considered coal combustion in power plants, and stoves are a key source of As in the local environment. Three mobilization and distribution scenarios were developed for potential As pathways in this semiarid environment. About 43 soil and 14 water sites were analyzed for As concentrations and meaningful parameters in soil and water. About 28 topsoil samples were analyzed in surface-subsurface pairs in order to identify potential eolian surface enrichment. Additionally, fluvial-alluvial sediments and geogenic and anthropogenic deposits were sampled. Water was sampled as surface water, groundwater, precipitation, and industrial water. Results show that As does not pose a ubiquitous risk in the Nalaikh Depression. However, locally and specifically in water, As concentrations may exceed the WHO guideline value for drinking water by up to a factor of 10. A carefully selected sampling strategy allows the evaluation of the distribution scenarios, which reveals a combination of (a) geogenic As in groundwater and distribution via surface water with (b) anthropogenic As redistribution via eolian pathways. An immediate linkage between As redistribution and coal mining is not evident. However, As distribution in fly ash from coal combustion in the local power plant and yurt settlements is the most likely As pathway. Hence, the results indicate the potential influence of diffuse, low-altitude sources on As emission to the environment. As such, this study provides a good example for As distribution under semiarid climate conditions influenced by geogenic and anthropogenic factors.

     

有机磷通过弱透水层的迁移转化规律研究

在地下水超量开采区,上层劣质潜水可以越过弱透水层补给承压水.有机磷能否随水迁移进入深层地下水构成水质污染是极为关注的问题.采用施压条件下将一定浓度的有机磷溶液渗透通过粘性土柱的模拟实验,对有机磷在饱和粘性土层中降解转化的各种因子及其影响机制进行分析,探讨有机磷在弱透水层环境中的降解转化和迁移的规律.结果表明:(1)粘性...     

Actinide geochemistry: From the molecular level to the real system

Geochemical processes leading to either mobilization or retention of radionuclides in an aquifer system are significantly influenced by their interaction with rock, sediment and colloid surfaces. Therefore, a sound safety assessment of nuclear waste disposal requires the elucidation and quantification of those processes. State-of-the-art analytical techniques as e.g. laser- and X-ray spectroscopy are increasingly applied to study solid–liquid interface reactions to obtain molecular level speciation insight.We have studied the sorption of trivalent lanthanides and actinides onto aluminium oxides, hydroxides and purified clay minerals by the time-resolved laser fluorescence spectroscopy and X-ray-absorption spectroscopy. Chemical constitution and structure of surface bound actinides are proposed based on spectroscopic information. Open questions still remain with regard to the exact nature of mineral surface ligands and the mineral/water interface. Similarities of spectroscopic data obtained for M(III) sorbed onto γ-alumina, and clay minerals suggest the formation of very comparable inner-sphere surface complexes such as S–O–An(III)(OH)_x^(2 − x)(H₂O)_5 − x at pH > 5. Those speciation data are found consistent with those predicted by surface complexation modelling. The applicability of data obtained for pure mineral phases to actinide sorption onto heterogeneously composed natural clay rock is examined by experiments and by geochemical modelling. Good agreement of experiment and model calculations is found for U(VI) and trivalent actinide/lanthanide sorption to natural clay rock. The agreement of spectroscopy, geochemical modelling and batch experiments with natural rock samples and purified minerals increases the reliability in model predictions.The assessment of colloid borne actinide migration observed in various laboratory and field studies calls for detailed information on actinide–colloid interaction. Kinetic stabilization of colloid bound actinides can be due to inclusion into inorganic colloid matrix or by macromolecular rearrangement in case of organic, humic/fulvic like colloids. Only a combination of spectroscopy, microscopy and classical batch sorption experiments can help to elucidate the actinide–colloid interaction mechanisms and thus contribute to the assessment of colloids for radionuclide migration.     

Phosphate rock formation and marine phosphorus geochemistry: the deep time perspective

The role that phosphorite formation, the ultimate source rock for fertilizer phosphate reserves, plays in the marine phosphorus (P) cycle has long been debated. A shift has occurred from early models that evoked strikingly different oceanic P cycling during times of widespread phosphorite deposition to current thinking that phosphorite deposits may be lucky survivors of a series of inter-related tectonic, geochemical, sedimentological, and oceanic conditions. This paradigm shift has been facilitated by an awareness of the widespread nature of phosphogenesis—the formation of authigenic P-bearing minerals in marine sediments that contributes to phosphorite formation. This process occurs not just in continental margin sediments, but in deep sea oozes as well, and helps to clarify the driving forces behind phosphorite formation and links to marine P geochemistry.Two processes come into play to make phosphorite deposits: chemical dynamism and physical dynamism. Chemical dynamism involves the diagenetic release and subsequent concentration of P-bearing minerals particularly in horizons, controlled by a number of sedimentological and biogeochemical factors. Physical dynamism involves the reworking and sedimentary capping of P-rich sediments, which can either concentrate the relatively heavy and insoluble disseminated P-bearing minerals or provide an episodic change in sedimentology to concentrate chemically mobilized P. Both processes can result from along-margin current dynamics and/or sea level variations. Interestingly, net P accumulation rates are highest (i.e., the P removal pump is most efficient) when phosphorites are not forming. Both physical and chemical pathways involve processes not dominant in deep sea environments and in fact not often coincide in space and time even on continental margins, contributing to the rarity of high-quality phosphorite deposits and the limitation of phosphate rock reserves. This limitation is becoming critical, as the human demand for P far outstrips the geologic replacement for P and few prospects exist for new discoveries of phosphate rock.     

Factors influencing natural occurrence of fluoride-rich groundwaters: a case study in the southeastern part of the Korean Peninsula

Factors regulating the occurrence of fluoride in groundwater were investigated using natural isotope tracers and geochemical data in the southeastern part of Korea where about 10% of the total public water-supply wells (n=422) inspected in this study had fluoride levels exceeding the drinking water limit of Korea (1.5 mg/l). The F-rich public wells are mostly distributed along the major faults, especially in the terrain of the F-rich granitic rocks. The stable isotope analysis results provide substantial information for the relative ages of groundwaters. It is revealed that the F-rich groundwaters are deeply circulating paleogroundwaters and occur along the faults due to upward flow along the fault plane. While reacting with granitic rocks for a prolonged period, the F concentrations of groundwater are continuously enriched even after the groundwater reaches an equilibrium state with respect to fluorite (CaF2) due to removal of Ca by precipitation of calcite (CaCO3). These observations reflect that rock chemistry, groundwater age, well depth, and geologic structure are the important factors controlling the occurrence of high F groundwaters. However, high F groundwaters are rarely observed in the fault zones where the associated fractures are widely developed. Isotopic signature provides an evidence for deep penetration of recently recharged groundwater into the wide fault zone, indicating that the hydrologic condition of the fault is also an important factor controlling the occurrence of high F groundwaters.