On the front conditions for gravity currents in channels of general cross-section

We consider the propagation of a high-Reynolds-number gravity current in a horizontal channel with general cross-section whose width is \(f(z), 0 \le z\le H\), and the gravity acceleration g acts in \(-z\) direction. (The classical rectangular cross-section is covered by the particular case \(f(z) =\) const.) We assume a two-layer system of homogeneous fluids of constant densities \(\rho _{c}\) (current, of height \(h < H \)) and smaller \(\rho _{a}\) (ambient, filling the remaining part of the channel). We focus attention on the calculation and assessment of the nose Froude-number condition \(Fr = U/(g' h)^{1/2}\); here U is the speed of propagation of the current and \(g' = (\rho _{c}/\rho _{a}-1) g\) is the reduced gravity. We first revisit the steady-state current, and derive compact insightful expressions of Fr and energy dissipation as a function of \(\varphi \) (\(=\) area fraction occupied by the current in the cross-section). We show that the head loss \(\delta _0\) on the stagnation line is formally a degree of freedom in the determination of \(Fr(\varphi )\), and we clarify the strong connections with the head loss \(\delta \) in the ambient fluid, and with the overall rate of dissipation \(\dot{{\mathcal{D}}}\). We demonstrate that the closure \(\delta _0 = 0\) [suggested by Benjamin (J Fluid Mech 31, 209–248, 1968) for the rectangular cross-section] produces in general the smallest Fr for a given \(\varphi \); the results are valid for a significant range \([0, \varphi _{\max }]\), in which the current is dissipative, except for the point \(\varphi _{\max }\) where \(\delta = \dot{{\mathcal{D}}} = 0\). We show that imposing the closure \(\delta = \dot{{\mathcal{D}}} = 0\), which corresponds to an energy-conserving or non-dissipative current, produces in general unacceptable restrictions of the range of validity, and large values of Fr; in particular, deep currents (\(\varphi < 0.3\) say) must be excluded because they are inherently dissipative. On the other hand, the compromise closure \(\delta (\varphi ) =\delta _0(\varphi )\) produces the simple \(Fr(\varphi ) = \sqrt{2}(1 - \varphi )\) formula whose values and dissipation properties are very close, and the range of validity is identical, to these obtained with Benjamin’s closure (moreover, we show that this corresponds to circulation-conservation solutions). The results are illustrated for practical cross-section geometries (rectangle, \(\Delta \) and \(\nabla \) triangle, circle, and the general power-law \(f(z) = b z ^\alpha \) (\(b>0, \alpha \ge 0, 0< z \le H\)). Next, we investigate the connection of the steady-state results with the time-dependent current, and show that in a lock-released current the rate of dissipation of the system is equal to, or larger than, that obtained for Fr corresponding to the conditions at the nose of the current. The results and insights of this study cover a wide range of cross-section geometry and apply to both Boussinesq and non-Boussinesq systems; they reveal a remarkable robustness of Fr as a function of \(\varphi \).     

Analysis and prediction of $$\mathrm{PM}_{10}$$ concentration levels in Tunisia using statistical learning approaches

Over the past years, the health impact of airborne particulate matter \(\mathrm{PM}_{10}\) has become a very topical subject. Thereby, a lot of research effort in the environmental sciences goes towards the modeling and the prediction of ambient \(\mathrm{PM}_{10}\) concentrations. In this paper, we are interested in the statistical classification of the daily mean \(\mathrm{PM}_{10}\) concentration in Tunisia according to the authority regulation. We consider two monitoring stations: a big industrial station and a traffic station. The main goal of this work is to determine the pertinent predictors of \(\mathrm{PM}_{10}\) concentration within a nonlinear multiclass framework. To do this, we used two popular statistical learning methods; the support vector machines (SVM) and the random forests (RF). The statistical results obtained on the real datasets, show that RF outperform SVM for the purpose of variable selection even with a reduced number of observations compared to the number of explicative variables. It was also demonstrated that the \(\mathrm{PM}_{10}\) concentration measured yesterday is the most relevant predictor of its present-day value. Moreover, we found that the more delayed values of \(\mathrm{PM}_{10}\) concentration may be crucial to get an accurate prediction.     

Fitting the truncated negative binomial distribution to count data

Modeling empirical distributions of repeated counts with parametric probability distributions is a frequent problem when studying species abundance. One must choose a family of distributions which is flexible enough to take into account very diverse patterns and possess parameters with clear biological/ecological interpretations. The negative binomial distribution fulfills these criteria and was selected for modeling counts of marine fish and invertebrates. This distribution depends on a vector \(\left( K,\mathfrak {P}\right) \) of parameters, and ranges from the Poisson distribution (when \(K\rightarrow +\infty \)) to Fisher’s log-series, when \(K\rightarrow 0\). Moreover, these parameters have biological/ecological interpretations which are detailed in the literature and in this study. We compared three estimators of K, \(\mathfrak {P}\) and the parameter \(\alpha \) of Fisher’s log-series, following the work of Rao CR (Statistical ecology. Pennsylvania State University Press, University Park, 1971) on a three-parameter unstandardized variant of the negative binomial distribution. We further investigated the coherence underlying parameter values resulting from the different estimators, using both real count data collected in the Mauritanian Exclusive Economic Zone (MEEZ) during the period 1987–2010 and realistic simulations of these data. In the case of the MEEZ, we first built homogeneous lists of counts (replicates), by gathering observations of each species with respect to “typical environments” obtained by clustering the sampled stations. The best estimation of \(\left( K,\mathfrak {P}\right) \) was generally obtained by penalized minimum Hellinger distance estimation. Interestingly, the parameters of most of the correctly sampled species seem compatible with the classical birth-and-dead model of population growth with immigration by Kendall (Biometrika 35:6–15, 1948).     

Wind-induced pressure at a tunnel portal

In order to properly size the mechanical ventilation system of a tunnel, it is essential to estimate the wind-driven pressure difference that might rise between its two portals. In this respect, we explore here the pressure distribution over a tunnel portal under the influence of an incident atmospheric boundary layer and, in particular, its dependency on wind direction and on tunnel geometry. Reduced scale models of generic configurations of a tunnel portal are studied in an atmospheric wind tunnel. Pressure distributions over the front section of different open cavities are measured with surface taps, which allows us to infer the influence of the tunnel aspect ratio and wind direction on a pressure coefficient \(C_{P}\), defined as a spatially and time averaged non-dimensional pressure. Experiments reveal that the magnitude of the coefficient \(C_{P}\), as a function of the wind direction, is significantly influenced by the portal height-to-width ratio and almost insensitive to its length. The experimental data set is completed by hot-wire anemometry measurements providing vertical distribution of velocity statistics. The same configurations are simulated by numerically solving the Reynolds-averaged Navier–Stokes equations, adopting the standard \(k - \varepsilon\) turbulence model. Despite some discrepancies between numerical and experimental estimates of some flow parameters (namely the turbulent kinetic energy field), the numerical estimates of the pressure coefficients \(C_{P}\) show very good agreement with experimental data. The latter is also compared to the predictions of an analytical model, based on the estimate of a spatially averaged velocity within an infinitely long street canyon. The results of the model, which takes into account varying canyon aspect ratios, are in reasonable agreement with experimental data for all cases studied. Notably, its predictions are significantly better than those provided by the simple analytical relations usually adopted as a reference in tunnel ventilation studies.     

Variations of bed elevations due to turbulence around submerged cylinder in sand beds

This paper presents the spatio-temporal variations in bed elevations and the near-bed turbulence statistics over the deformed bed generated around the submerged cylindrical piers embedded vertically on loose sediment bed at a constant flow discharge. Experiments were carried out in a laboratory flume for three blockage ratios in the range of 0.04–0.06 using three different sizes of submerged cylinders individually placed vertically at the centerline of the flume. Clear-water experimental conditions were maintained over the smooth sediment bed surface with a constant flow discharge (\(Q = 0.015\,{\rm m}^3/{\rm sec}\)), thereby giving three different cylinder Reynolds numbers \(Re_{D_c} = \frac{U_mD_c}{\nu }\) (=10200, 12750, 15300) away from the cylinder locations, where \(U_m\) is the maximum mean velocity, \(D_c\) is the cylinder diameter and \(\nu\) is the kinematic viscosity of fluid. Instantaneous sand bed elevations around the cylinders were recorded using a SeaTek 5MHz ultrasonic ranging system of net 24 transducers to estimate bed form migration, and the near-bed velocity data at transducer locations over the stable deformed bed around the pier-like structures were collected using down-looking three-dimensional (3D) Micro-acoustic Doppler velocimeter to estimate the bottom Reynolds shear stresses and the contributions of bursting events to the dominant shear stress component. The flow perturbation generated due to relatively lower flow blockage ratio favored to achieve the stable bed condition more rapidly than the others, and larger upstream scour-depth and deformed areas were noticed for greater flow blockage ratio due to larger cylinder diameter. For larger blockage ratio in the upstream of scour-hole near the bed, occurrences of probabilities of both boundary-ward interactions (Q1 and Q3) were the dominant; whereas in the downstream of the scoured region, occurrences of probabilities of second and third quadrant events (Q2 and Q4) were dominant. On the other hand, for the lower blockage ratio, quadrant (Q2) was dominant over Q4 in the downstream of scour-hole, and in the upstream of scour-hole, quadrant Q4 was the dominant.     

Penetrative convection in slender containers

An experimental study was conducted to investigate the penetration of a convective mixed layer into an overlying stably (solutally) stratified layer contained in a narrow, tall vessel when the fluid is subjected to a destabilizing heat flux from below. The interest was the evolution of the bottom mixed-layer height (\(h\)) with time (\(t\)) in the presence of side-wall effects, but without the formation of conventional double-diffusive layers. The side-wall effects are expected at small mixed-layer aspect ratios, \(\varGamma_{h} = (W/h)\), where \(W\) is the container width. This case has not been studied hitherto, although there are important environmental and industrial applications. The mixed-layer growth laws for low aspect ratio convection were formulated by assuming a balance between the vertical kinetic energy flux at the interface and the rate of change of potential energy of the fluid system due to turbulent entrainment. The effects of sidewalls were considered using similarity arguments, by taking characteristic rms velocities to be a function of \(\varGamma_{h}\), in addition to buoyancy flux (\(q_{0}\)) and \(h\). In all stages of evolution, the similarity variables \(\xi = h/W\) and \(t^{\prime } = Nt/A\), where \(A = N^{3} W^{2} /4q_{0}\) and \(N\) is the buoyancy frequency, scaled the mixed-layer evolution data remarkably well. Significant wall effects were noted when \(\varGamma_{h} < 1\), and for this case the interfacial vertical turbulent velocity and length scales were identified via scaling arguments and experimental data.     

Thin-layer models for gravity currents in channels of general cross-section area,a review

We present a brief review of the recent investigations on gravity currents in horizontal channels with non-rectangular cross-section area (such as triangle, \(\bigvee \)-valley, circle/semi-circle, trapezoid) which occur in nature (e.g., rivers) and constructed environment (tunnels, reservoirs, canals). To be specific, we discuss the propagation of a gravity current (GC) in a horizontal channel along the horizontal coordinate x, with gravity g acting in the \(-z\) direction, and y the horizontal–lateral coordinate. The bottom and top of the channel are at \(z=0,H\). The “standard” problem is concerned with 2D flow in a channel with rectangular (or laterally unbounded) cross-section area (CSA). Recent investigations have successfully extended the standard knowledge to the channels of CSA given by the quite general \(-f_1(z)\le y \le f_2(z)\) for \(0 \le z \le H\). This includes the practical \(\bigvee \)-valley, triangle, circle/semi-circle and trapezoid; these geometries may be in “up” or “down” setting with respect to gravity, e.g., \(\bigtriangleup \) and \(\bigtriangledown \). The major objective of the extended theory is to predict the height of the interface \(z=h(x,t)\) and the velocity (averaged over the CSA) u(x, t), where t is time; the prediction includes the speed and position of the nose \(u_N(t), x_N(t)\). We show that the motion is governed by a set of simplified equations, called “model,” that provides versatile and insightful solutions and trends. The emphasis in on a high-Reynolds-number current whose motion is dominated by buoyancy–inertia balance; in particular a GC released from a lock, which also contains general effects such as front and internal jumps (shocks), and reflected bore. We discuss two-layer, one-layer, and box models; Boussinesq and non-Boussinesq systems; compositional and particle-driven cases; and the effect of stratification of the ambient fluid. The models are self-contained, and admit realistic initial and boundary conditions. The governing equations are amenable to analytical solutions in some special circumstances. Some salient features of the buoyancy-viscous regime, and the estimate for the length at which transition to this regime takes place, are also presented. Some experimental support to the theory, and open questions for further investigations, are also mentioned. The major conclusions are (1) The CSA geometry has significant influence on the motion of the GC; and (2) The new theory is a useful, very significant, extension of the standard two-dimensional GC problem. The standard current is just a particular case, \(f_{1,2} =\) constants, among many other covered by the new theory.     

Nanostructured semiconducting materials for efficient hydrogen generation

Massive production of hydrogen by water decomposition triggered by a solar light active photocatalyst is a major objective in chemistry and a promising avenue to overcome the global energy crisis. The development of efficient, stable, economically viable and eco-friendly photocatalysts for hydrogen production is a challenging task. This article reviews the use of nanocomposite in three combinations: metal oxide–metal oxide semiconductor, metal–metal oxide semiconductor and metal chalcogenide–metal oxide core–shell nanostructures. These core–shell structures occur in two forms: a simple form where the photocatalyst is either in the core or the shell or in a more complex system where the core–shell structure comprises a co-catalyst deposited on a semiconducting material. We discuss the design, synthesis and development of semiconductor-based nanocomposite photocatalysts for hydrogen production. The major points are the role of catalytic active sites, the chemical nature of sacrificial agents, the effect of light sources, the variable light intensity and the energy efficiency calculation. For TiO₂-based nanocomposites, the metal oxide or metal co-catalyst loading of 1.0–3.0 wt% was optimal. TiO₂ nanotube–CuO hybrid nanocomposites produce 1,14,000 µmol h^?1 \({\text{g}}^{ - 1}_{\text{cat}}\), whereas TiO₂/Au nanocomposites display 1,60,000 µmol h^?1 \({\text{g}}^{ - 1}_{\text{cat}}\). For core–shell catalysts, a shell thickness of 2–20 nm was found for the best activity, and its performance is as follows: (a) CdS–NiO system produces around 19,949 µmol h^?1 \({\text{g}}^{ - 1}_{\text{cat}}\) and (b) CuO–Cr₂O₃ as co-catalyst immobilized on TiO₂ system produces around 82,390 µmol h^?1 \({\text{g}}^{ - 1}_{\text{cat}}\).     

Small-scale entrainment in inclined gravity currents

We investigate the effect of buoyancy on the small-scale aspects of turbulent entrainment by performing direct numerical simulation of a gravity current and a wall jet. In both flows, we detect the turbulent/nonturbulent interface separating turbulent from irrotational ambient flow regions using a range of enstrophy iso-levels spanning many orders of magnitude. Conform to expectation, the relative enstrophy isosurface velocity \(v_n\) in the viscous superlayer scales with the Kolmogorov velocity for both flow cases. We connect the integral entrainment coefficient E to the small-scale entrainment and observe excellent agreement between the two estimates throughout the viscous superlayer. The contribution of baroclinic torque to \(v_n\) is negligible, and we show that the primary reason for reduced entrainment in the gravity current as compared to the wall-jet are 1) the reduction of \(v_n\) relative to the integral velocity scale \(u_T\); and 2) the reduction in the surface area of the isosurfaces.     

Evaluation of acidity in late Permian outcrop coals and its association with endemic fluorosis in the border area of Yunnan,Guizhou, and Sichuan in China

The junction area of Yunnan, Guizhou, and Sichuan provinces is the heaviest coal-burning endemic fluorosis zones in China. To better understand the pathogenicity of endemic fluorosis in this area, 87 coal samples from the late Permian outcrop or semi-outcrop coal seams were collected in eight counties of the junction area of Yunnan, Guizhou, and Sichuan provinces. The total fluorine and sulfate content, etc. in the coal was determined using combustion-hydrolysis/fluoride-ion-selective electrode method and ion chromatography, respectively. The results show that the total fluorine concentrations in the samples ranged from 44 to 382 µg g^?1, with an average of 127 µg g^?1. The average pH of the coals is 5.03 (1.86–8.62), and the sulfate content varied from 249 to 64,706 µg g^?1 (average 7127 µg g^?1). In addition, the coals were medium- and high-sulfur coals, with sulfur mass fraction ranging from 0.08 to 13.41%. By heating the outcrop coals, HF release from the coal was verified quantitatively without exception, while simulated combustion directly confirmed the release of sulfuric acid (H₂SO₄). The acid in coal may be in the form of acidic sulfate (\({\text{HSO}}_{4}^{ - }\)/H₂SO₄) because of a positive relationship between pH and \(p\left( {{\text{SO}}_{4}^{2 - } } \right)\) in the acidic coal. The possible reaction mechanism would be that a chemical reaction between the acid (H₂SO₄ or \({\text{HSO}}_{4}^{ - }\)) and fluorine in the coal occurred, thereby producing hydrogen fluoride (HF), which would be the chemical form of fluorine released from coal under relatively mild conditions. The unique chemical and physical property of HF may bring new insight into the pathogenic mechanism of coal-burning endemic fluorosis. The phenomenon of coal-burning fluorosis is not limited to the study area, but is common in southwest China and elsewhere. Further investigation is needed to determine whether other endemic fluorosis areas are affected by this phenomenon.     

Mixing at a sediment concentration interface in turbulent open channel flow

In this work we address the role of turbulence on mixing of clear layer of fluid with sediment-laden layer of fluid at a sediment concentration interface. This process can be conceived as the entrainment of sediment-free fluid into the sediment-laden layer, or alternatively, as the transport of sediment into the top sediment-free flow. This process is governed by four parameters—Reynolds number of the flow \(Re_\tau\), non-dimensional settling velocity of the sediment (proxy for sediment size) \(\tilde{V}\), Richardson number \(Ri_\tau\) and Schmidt number Sc. For this work we have performed direct numerical simulations for fixed Reynolds and Schmidt numbers while varying the values of Richardson number and particle settling velocity. In the simple model considered here, the flow’s momentum and turbulence pre-exists over the entire layer of fluid, while the sediment is initially confined to a layer close to the bed. Mixing of sediment-free fluid with the sediment-laden layer is associated primarily with upward transport of sediment and buoyancy. There is no simultaneous upward transport of fluid momentum and turbulence into the sediment-free fluid layer, which is already in motion and turbulent. The analysis performed shows that the ability of the flow to transport a given sediment size decreases with the distance from the bottom, and thus only fine enough sediment particles are transported across the sediment concentration interface. For these cases, the concentration profiles evolve to a final steady state in good agreement with the well-known Rouse profile. The approach towards the Rouse profile happens through a transient self-similar state. This behavior of the flow is not seen for larger particles. Detailed analysis of the three dimensional structure of the sediment concentration interface shows the mechanisms by which sediment particles are lifted up by tongues of sediment-laden fluid with positive correlation between vertical velocity and sediment concentration. Finally, the mixing ability of the flow is addressed by monitoring the time evolution of the center of mass of the sediment-laden layer and the vertical location of the sediment-free/sediment-laden interface.     

Investigating the link between $$\hbox {PM}_{2.5}$$ and atmospheric profile variables via penalized functional quantile regression

Fine particulate matter (\(\hbox {PM}_{2.5}\)) events negatively affect the health of numerous persons globally each year. Previous works have described the association between air pollution and surface-level meteorological conditions; however, there has been less focus on the task of linking air pollution events with meteorological conditions at higher levels of the atmosphere. Working within the functional data framework, we develop a penalized functional quantile regression (PFQR) procedure to model conditional quantiles of a continuous response based on a functional covariate, with the ability to penalize selected derivatives of the estimated coefficient function. Our aim is to investigate the relationship between atmospheric profile variables (APVs), assumed to be functional, and key quantiles of the conditional distribution of surface-level \(\hbox {PM}_{2.5}\). Via a simulation study, we find that the performance of our PFQR procedure compares favorably to other related approaches. We conclude with an analysis of \(\hbox {PM}_{2.5}\) data at two Southeastern US locations, Columbia, SC and Tampa, FL, where we estimate the coefficient functions for the APVs corresponding to both ‘typical’ and ‘high’ \(\hbox {PM}_{2.5}\) events. As we believe that the true coefficient functions are smooth and may be exactly zero over subsets of their domains, we impose penalties on the 0th and 2nd derivatives. Our analysis indicates that the corresponding atmospheric conditions differ between the two locations, and that the conditions differ seasonally within location.     

Development of similarity relationships for energy dissipation rate and temperature structure parameter in stably stratified flows: a direct numerical simulation approach

In this study, a newly developed direct numerical simulation (DNS) solver is utilized for the simulations of numerous stably stratified open-channel flows with bulk Reynolds number (Re _b ) spanning 3400–16,900. Overall, the simulated bulk Richardson number (\(Ri_b\)) ranges from 0.08 (weakly stable) to 0.49 (very stable). Thus, both continuously turbulent and (globally) intermittently turbulent cases are represented in the DNS database. Using this comprehensive database, various flux-based and gradient-based similarity relationships for energy dissipation rate (ε) and temperature structure parameter (\(C_T^2\)) are developed. Interestingly, these relationships exhibit only minor dependency on Re _b . In order to further probe into this Re _b -effect, similarity relationships are also estimated from a large-eddy simulation (LES) run of an idealized atmospheric boundary layer (very high Re _b ) case study. Despite the fundamental differences in the estimation of ε and \(C_T^2\) from the DNS- and the LES-generated data, the resulting similarity relationships, especially the gradient-based ones, from these numerical approaches are found to be remarkably similar. More importantly, these simulated relationships are also comparable, at least qualitatively, to the traditional observational data-based ones. Since these simulated similarity relationships do not require Taylor’s hypothesis and do not suffer from mesoscale disturbances and/or measurement noise, they have the potential to complement the existing similarity relationships.     

Waves and turbulence in katabatic winds

The measurements taken during the Vertical Transport and Mixing Experiment (VTMX, October, 2000) on a northeastern slope of Salt Lake Valley, Utah, were used to calculate the statistics of velocity fluctuations in a katabatic gravity current in the absence of synoptic forcing. The data from ultrasonic anemometer-thermometers placed at elevations 4.5 and 13.9 m were used. The contributions of small-scale turbulence and waves were isolated by applying a high-pass digital (Elliptical) filter, whereupon the filtered quantities were identified as small-scale turbulence and the rest as internal gravity waves. Internal waves were found to play a role not only at canonical large gradient Richardson numbers $(\overline{\hbox {Ri}_\mathrm{g} } >1)$ , but sometimes at smaller values $(0.1 < \overline{\hbox {Ri}_\mathrm{g}}<1)$ , in contrast to typical observations in flat-terrain stable boundary layers. This may be attributed, at least partly, to (critical) internal waves on the slope, identified by Princevac et al. [1], which degenerate into turbulence and help maintain an active internal wave field. The applicability of both Monin-Obukhov (MO) similarity theory and local scaling to filtered and unfiltered data was tested by analyzing rms velocity fluctuations as a function of the stability parameter z/L, where L is the Obukhov length and z the height above the ground. For weaker stabilities, $\hbox {z/L}<1$ , the MO similarity and local scaling were valid for both filtered and unfiltered data. Conversely, when $\hbox {z/L}>1$ , the use of both scaling types is questionable, although filtered data showed a tendency to follow local scaling. A relationship between z/L and $\overline{\hbox {Ri}_\mathrm{g} }$ was identified. Eddy diffusivities of momentum $\hbox {K}_\mathrm{M}$ and heat $\hbox {K}_\mathrm{H}$ were dependent on wave activities, notably when $\overline{\hbox {Ri}_\mathrm{g} } > 1$ . The ratio $\hbox {K}_{\mathrm{H}}/\hbox {K}_{\mathrm{M}}$ dropped well below unity at high $\overline{\hbox {Ri}_\mathrm{g} }$ , in consonance with previous laboratory stratified shear layer measurements as well as other field observations.     

The CPCAT as a novel tool to overcome the shortcomings of NOEC/LOEC statistics in ecotoxicology: a simulation study to evaluate the statistical power

Species reproduction is an important determinant of population dynamics. As such, this is an important parameter in environmental risk assessment. The closure principle computational approach test (CPCAT) was recently proposed as a method to derive a NOEC/LOEC for reproduction count data such as the number of juvenile Daphnia. The Poisson distribution used by CPCAT can be too restrictive as a model of the data-generating process. In practice, the generalized Poisson distribution could be more appropriate, as it allows for inequality of the population mean \(\mu\) and the population variance \(\sigma ^2\). It is of fundamental interest to explore the statistical power of CPCAT and the probability of determining a regulatory relevant effect correctly. Using a simulation, we varied between Poisson distribution (\(\mu =\sigma ^2\)) and generalized Poisson distribution allowing for over-dispersion (\(\mu <\sigma ^2\)) and under-dispersion (\(\mu >\sigma ^2\)). The results indicated that the probability of detecting the LOEC/NOEC correctly was \(\ge 0.8\) provided the effect was at least 20% above or below the mean level of the control group and mean reproduction of the control was at least 50 individuals while over-dispersion was missing. Specifically, under-dispersion increased, whereas over-dispersion reduced the statistical power of the CPCAT. Using the well-known Hampel identifier, we propose a simple and straight forward method to assess whether the data-generating process of real data could be over- or under-dispersed.     

Experiments on gravity currents propagating on unbounded uniform slopes

Gravity currents propagating on \(12^\circ \), \(9^\circ \), \(6^\circ \), \(3^\circ \) unbounded uniform slopes and on an unbounded horizontal boundary are reported. Results show that there are two stages of the deceleration phase. In the early stage of the deceleration phase, the front location history follows \({(x_f+x_0)}^2 = {(K_I B)}^{1/2} (t+t_{I})\), where \((x_f+x_0)\) is the front location measured from the virtual origin, \(K_I\) an experimental constant, B the total buoyancy, t time and \(t_I\) the t-intercept. In the late stage of the deceleration phase for the gravity currents on \(12^\circ \), \(9^\circ \), \(6^\circ \) unbounded uniform slopes, the front location history follows \({(x_f+x_0)}^{8/3} = K_{VS} {{B}^{2/3} V^{2/9}_0 }{\nu }^{-1/3} ({t+t_{VS}})\), where \(K_{VS}\) is an experimental constant, \(V_0\) the initial volume of heavy fluid, \(\nu \) the kinematic viscosity and \(t_{VS}\) the t-intercept. In the late stage of the deceleration phase for the gravity currents on a \(3^\circ \) unbounded uniform slope and on an unbounded horizontal boundary, the front location history follows \({(x_f+x_0)}^{4} = K_{VM} {{B}^{2/3} V^{2/3}_0 }{\nu }^{-1/3} ({t+t_{VM}})\), where \(K_{VM}\) is an experimental constant and \(t_{VM}\) the t-intercept. Two qualitatively different flow morphologies are identified in the late stage of the deceleration phase. For the gravity currents on \(12^\circ \), \(9^\circ \), \(6^\circ \) unbounded uniform slopes, an ‘active’ head separates from the body of the current. For the gravity currents on a \(3^\circ \) unbounded uniform slope and on an unbounded horizontal boundary, the gravity currents maintain an integrated shape throughout the motion. Results indicate two possible routes to the final stage of the gravity currents on unbounded uniform slopes.

     

Effect of wastewater composition on the calcium carbonate precipitation in upflow anaerobic sludge blanket reactors

Calcium carbonate often precipitates in anaerobic reactors treating wastewater with high calcium content. The aim of this paper is to study the effect of wastewater composition on calcium carbonate precipitation in upflow anaerobic sludge blanket (UASB) reactors. Two laboratory-scale UASB reactors were operated with calcium-containing influents using acetate and carbohydrate as substrate, respectively. There was an obvious accumulation of inorganic precipitate observed in the biogranules. Observations via scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) showed that the acclimated biogranules in the two reactors differed in microstructure. Calcium carbonate was found to have precipitated on the surface of acetate-degrading biogranules, but precipitated at the core of the carbohydrate-degrading biogranules. The results indicated that substrates had significant influence on the location of calcium carbonate precipitation in anaerobic granular sludge, which was expected due to the different methanogens distribution and pH gradient within the granular sludge degrading various substrates. Moreover, the location of calcium carbonate precipitation substantially affected the specific methanogenic activity (SMA) of the granular sludge. The SMA of the acetate-degrading biogranules dropped from \(1.96 gCOD_{CH_4 } \cdot gVSS^{ - 1} \cdot d^{ - 1} \) to \(0.61 gCOD_{CH_4 } \cdot gVSS^{ - 1} \cdot d^{ - 1} \) after 180-d of operation in the reactor. However, the SMA of the carbohydrate-degrading biogranules was not adversely affected by calcium carbonate precipitation.     

Effect of atmospheric boundary layer stability on the inclination angle of turbulence coherent structures

Coherent structures in the atmospheric boundary layer are fundamental to the transport of momentum and heat as well as to the production of turbulence. The present work attempts to investigate the behavior of the inclination angle of the vortex packet structures (\(\gamma\)) under different stability conditions. The data were collected from the Marine Ecosystem Research Centre (EKOMAR) site at the east coast of Peninsular Malaysia. The main measurements were conducted by placing two hotwires 3 and 12 m above ground. The two-point correlation method was used to calculate the vortex packet structure inclination angle, while the one-point correlation method was employed to calculate its length-scale. The inclination angle was found to increase under both stable and unstable conditions. As the Obukhov stability parameter (\(\zeta\)) approaches 0, the inclination angle ranged between \(\gamma = 15^\circ\) to \(\gamma = 18^\circ\) for the stable and unstable conditions, respectively, which agrees with the findings of previous research. The vertical gradient of velocity is the dominant parameter affecting the inclination angle under different stability conditions.     

Hydrogeochemistry study and groundwater quality assessment in the north of Isfahan,Iran

This study presents the groundwater quality assessment in the north of Isfahan, Iran. In the study area, assessment and measurement of groundwater hydrochemical parameters such as pH, total dissolved solids (TDS), electrical conductivity (EC), sodium absorption ratio (SAR), total hardness, major cations (K⁺, Na⁺, Ca²⁺ and Mg²⁺) and major anions (Cl^?, \({\text{HCO}}_{ 3}^{ - } ,{\text{CO}}_{3}^{2 - }\) and \({\text{SO}}_{4}^{2 - }\)) concentrations were performed. Accordingly, the 66 water samples from different locations were collected during April and May 2015. Water samples collected in the field were analyzed in the laboratory for cations and anions using the standard methods. In this research, the analytical results of physiochemical parameters of groundwater were compared with the standard guideline values as recommended by the world health organization (WHO) for drinking and public health purposes. The pH values of groundwater samples varied from 7.05 to 8.95 with a mean of 7.78, indicating a neutral to slightly alkaline water. TDS values showed that 14% of the samples exceeds the desirable limit given by WHO. EC values varied from 213 to 4320 µS/cm, while 23% of the samples were more than the standard limit. Gibbs diagram had shown that 90% of the samples in the study area fall in the rock weathering zone, and this means that chemical weathering of rock-forming minerals is the main factor controlling the water chemistry in the study area. Irrigation suitability and risk assessment of groundwater are evaluated by measuring EC, %Na, SAR and RSC. According to the dominant cations and anions, five types of water were identified in the water samples: Ca-HCO₃, Ca-SO₄, Na-Cl, Na-HCO₃ and Na-SO₄. The results show that the majority of samples (30 samples, 45%) belongs to the mixed Na-SO₄ water type. Correlation analysis and principal component analysis was used to identify the relationship between ions and physicochemical parameters. Results indicated that 18 stations of the study area had the best quality and can be used for irrigation and drinking purposes in the future.     

Compound channel flow with a longitudinal transition in hydraulic roughness over the floodplains

Flows in a compound open-channel (two-stage geometry with a main channel and adjacent floodplains) with a longitudinal transition in roughness over the floodplains are experimentally investigated in an 18 m long and 3 m wide flume. Transitions from submerged dense vegetation (meadow) to emergent rigid vegetation (wood) and vice versa are modelled using plastic grass and vertical wooden cylinders. For a given roughness transition, the upstream discharge distribution between main channel and floodplain (called subsections) is also varied, keeping the total flow rate constant. The flows with a roughness transition are compared to flows with a uniformly distributed roughness over the whole length of the flume. Besides the influence of the downstream boundary condition, the longitudinal profiles of water depth are controlled by the upstream discharge distribution. The latter also strongly influences the magnitude of the lateral net mass exchanges between subsections, especially upstream from the roughness transition. Irrespective of flow conditions, the inflection point in the mean velocity profile across the mixing layer is always observed at the interface between subsections. The longitudinal velocity at the main channel/floodplain interface, denoted \(U_{int}\), appeared to be a key parameter for characterising the flows. First, the mean velocity profiles across the mixing layer, normalised using \(U_{int}\), are superimposed irrespective of downstream position, flow depth, floodplain roughness type and lateral mass transfers. However, the profiles of turbulence quantities do not coincide, indicating that the flows are not fully self-similar and that the eddy viscosity assumption is not valid in this case. Second, the depth-averaged turbulent intensities and Reynolds stresses, when scaled by the depth-averaged velocity \(U_{d,int}\) exhibit two plateau values, each related to a roughness type, meadow or wood. Lastly, the same results hold when scaling by \(U_{d,int}\) the depth-averaged lateral flux of momentum due to secondary currents. Turbulence production and magnitude of secondary currents are increased by the presence of emergent rigid elements over the floodplains. The autocorrelation functions show that the length of the coherent structures scales with the mixing layer width for all flow cases. It is suggested that coherent structures tend to a state where the magnitude of velocity fluctuations (of both horizontal vortices and secondary currents) and the spatial extension of the structures are in equilibrium.