Characterization and Properties of Reactive Poly (Lactic Acid)/Ethylene–Vinyl Alcohol Copolymer Blends with Chain-Extender

A hydrophilic copolymer, ethylene–vinyl alcohol (EVOH), was incorporated into the poly(lactic acid) (PLA) matrix to improve the barrier property of PLA through twin-screw extrusion rather than the typical coextrusion process. A chain extender, poly[(ethylene)-co-(methyl acrylate)-co-(glycidyl methacrylate)] (PEMG), was used to reduce the probability of the thermal degradation of PLA during melt compounding. Biaxial stretching was used to enhance the microstructure and barrier property of PLA-PEMG/EVOH films. Experimentally, PEMG considerably reduced the probability of the thermal degradation of the PLA-PEMG sample. Biaxial stretching increased the tensile strength and decreased the value of elongation at break of the PLA-PEMG/EVOH80 (PLA/EVOH 100/80) film. Because of the efficient blending of PLA/EVOH in the twin-screw extruder, the dispersion of EVOH in the PLA matrix revealed homogeneous dispersion with a domain size of 1–5 μm. EVOH effectively improved the water vapour transmission rate (WVTR) of PLA through melt blending. Blending PLA-PEMG with EVOH substantially decreased the WVTR from 250 cc—20 μm/m²-day-atm for neat PLA to approximately 65 cc—20 μm/m²-day-atm for the PLA-PEMG/EVOH80 film, a decrease of approximately 74 % compared with neat PLA. Moreover, the WVTR decreased further from 65 cc—20 μm/m²-day-atm for the unstretched PLA-PEMG/EVOH80 film to 6.3 cc—20 μm/m²-day-atm for the film stretched at a stretch ratio of 3.5 × 3.5 and at 100 %/s, a decrease of approximately 90 % compared with neat PLA.     

Bio‐Based Poly(3-hydroxybutyrate)/Thermoplastic Starch Composites as a Host Matrix for Biochar Fillers

Journal of Polymers and the Environment - Biochar is an excellent, but less-used candidate to serve as an alternative filler in poly(3-hydroxybutyrate) (PHB)-based composites. Increasing amounts of...     

Effects of Poly(Ethylene Glycol) on the Production of Poly(β-Hydroxybutyrate) by Azotobacter vinelandii UWD

Azotobacter vinelandii UWD, ATCC 53799, an engineered strain derived from Azotobacter vinelandii UW was used in the poly(ethylene glycol) (PEG)-modulated synthesis of poly(-hydroxybutyrate) (PHB). To the best of our knowledge, this is the first report on modulating the production of PHB by amending the fermentation broth with PEG using A. vinelandii UWD. It was determined that A. vinelandii UWD is prone to back-mutation to the parent strain; hence fermentation experiments require the use of the antibiotic rifampicin. Diethylene glycol (DEG) and PEGs with molecular weights of 400, 2000, and 3400 Da and pentaerythritol ethoxylate (PEE) were used in the modulated fermentation experiments in a concentration of 2% (w/v). The molecular weight of the resulting polymers was reduced by up to 78%. No impact on the productivity of the strain was observed. Spectroscopic evidence showed that PEG-modulated synthesis resulted in the covalent attachment of the ethylene glycol moiety only when a small molecule, DEG, was used. PEGs had the same effects on the polymer formation in terms of molecular weight reduction as DEG, but no spectroscopic evidence was found for the formation of a covalent linkage between PHB and higher molecular weight PEGs.     

Influence of Processing Additives on the Degradation of Melt-Pressed Films of Poly(ε-Caprolactone) and Poly(Lactic Acid)

Melt-pressed films of polycaprolactone (PCL) and poly(lactic acid) (PLA) with processing additives, CaCO₃, SiO₂, and erucamide, were subjected to pure fungal cultures Aspergillus fumigatus and Penicillium simplicissimum and to composting. The PCL films showed a rapid weight loss with a minor reduction in the molecular weight after 45 days in A. fumigatus. The addition of SiO₂ to PCL increased the rate of (bio)erosion in A. fumigatus and in compost. The use of a slip additive, erucamide, was shown to modify the properties of the film surface without decreasing the rate of bio(erosion). Both the rate of weight loss and the rate of molecular weight reduction of PCL increased with decreasing film thickness. The addition of CaCO₃ to PLA significantly reduced the thermal degradation during processing, but it also reduced the rate of the subsequent (bio)degradation in the pure fungal cultures. PLA without additives and PLA containing SiO₂ exhibited the fastest (bio)degradation, followed by PLA with CaCO₃. The degradation of the PLA films was initially governed by chemical hydrolysis, followed by an acceleration of the weight change and of the molecular weight reduction. PLA film subjected to composting exhibits a rapid decrease in molecular weight, which then remains unchanged during the measurement period, probably because of crystallization.     

Poly(2-ethyl-2-oxazoline) as β-Nucleating Agent for Poly(lactic acid) Blends with High Transparency and Hydrophilicity

Journal of Polymers and the Environment - This study aims to evaluate the effects of poly(2-ethyl-oxazoline) (PEOx) on the thermal properties, wettability, and optical properties of poly(lactic...     

Radiation Effects on Blends of Poly(ε-Caprolactone) and Diatomites

Poly(-caprolactone) (PCL) was blended with diatomaceous earth (diatomite) and irradiated with -rays to introduce cross-linking between PCL molecules or both components. The unwashed diatomite containing a little of a volatile component showed high efficiency of introduction of cross-linking, whereas that with no volatile component showed low efficiency of introduction of cross-linking. Elongational viscosity, melt viscosity, and modulus of PCL/diatomite blend irradiated at various doses were significantly improved. Enzymatic degradation of the PCL/diatomite blend became faster than that of the PCL, though that of the blend irradiated became slower.     

Distribution of Poly(β-propiolactone) Aerobic Degrading Microorganisms in Different Environments

The distribution of degading microorganisms of high molecular weight poly(-propiolactone) (PPL), whose individual structural units are similar to those of poly(-hydroxybutyrate) (PHB) and poly(€-caprolactone) (PCL), was examined. Despite the fact that PPL is a chemosynthetic polymer, many kinds of PPL-degrading microorganisms were found to be distributed as resident populations widely in natural environments. A total of 77 strains of PPL-degrading microorganisms was isolated. From standard physiological and biochemical tests, at least 41 strains were referred to as Bacillus species. Microbial degradation of fibrous PPL proceeded rapidly in some enrichment cultures but was not as complete as that of PHB. Most of the isolated PPL-degrading microorganisms were determined to be PCL degraders and/or PHB degraders. Therefore, it can be assumed that mostly PPL is recognized by the microorganisms as PHB or another natural substrate of the same type as which PCL is regarded. Microbial degradation of PPL was confirmed by some Bacillus strains from type culture collections. The similarity of microbial degradation between PPL and PCL was found to be very close.     

Evaluation of biodegradability of poly(ε-caprolactone)/poly(ethylene terephthalate) blends

The results of an investigation aimed at evaluation of the biodegradability of blends of poly(-caprolactone) (PCL) with poly(ethylene terephthalate) (PET) as the major component are reported. Specimens of the blends, as melt extruded films and/or powders, were submitted to degradation tests under different environmental conditions including full-scale composting, soil burial, bench-scale accelerated aerobic degradation, and exposure to axenic cultures and esterolytic enzymes. Indications have been gained that blending in the melt gives rise to insertion of PCL segments in the PET chain. Copolymers thus attained acted as macromolecular compatibilizers, allowing for a complete miscibility of PCL and PET. The biodegradation detected on the blend samples was, however, well below the values expected from chemical composition and behavior of individual homopolymers under the same environmental conditions. The presence of PET as the major component in PET/PCL blends apparently reduces the propensity of PCL to be degraded, at least in the investigated composition range. The degradation data collected under different environmental conditions indicate that the full-scale composting system is the most efficient among the tested degradation procedures.     

PW_(12)/g-C_3N_4光催化降解甲基橙

采用浸渍法制备了磷钨酸(PW12)/g-C3N4复合光催化剂,并将其用于溶液中甲基橙的光催化降解,运用IR技术对使用前后的光催化剂进行了表征。表征结果显示,PW12和g-C3N4的结构未在浸渍负载中发生改变,且PW12和g-C3N4结合牢固。实验结果表明:最佳的PW12负载量(光催化剂中PW12的质量分数)为50%;光催化降解甲基橙的优化反应条件为初始甲基橙质量浓度5 mg/L、光催化剂加入量0.6 g/L、初始溶液p H=7;在优化条件下,分别采用紫外光、模拟太阳光、可见光照射120 min后,甲基橙的降解率分别为96.59%,82.23%,42.78%;该光催化剂固载良好,使用中不易发生溶脱,稳定性好,可重复使用。     

H_4SiW_(12)O_(40)/TiO_2/空心微珠光催化降解联苯胺

采用复合型光催化剂H_4SiW_(12)O_(40)/TiO_2/空心微珠(cenospheres)光催化降解联苯胺,考察了联苯胺降解效果的影响因素,并运用FTIR和GS-MS技术分析了联苯胺光催化降解过程的主要中间产物,探讨了联苯胺可能的降解路径。实验结果表明:以125 W中压汞灯为光源,在溶液pH为6.3,初始联苯胺质量浓度为10 mg/L的条件下光反应240 min,联苯胺降解率达78%,比Ti_O2/空心微珠提高了24百分点;H_4SiW_(12)O_(40)/TiO_2/空心微珠光催化降解联苯胺符合表观一级动力学特征,且反应速率常数随初始联苯胺质量浓度的增加而减小;H_4SiW_(12)O_(40)/TiO_2/空心微珠具有较好的稳定性,易于分离,可重复利用;联苯胺光催化降解过程的主要中间产物为4-氨基联苯、4-氨基苯酚、对苯二酚和1,4-苯醌。     

Pt-Fe(Ⅲ)/PAni/GCE电极的制备及NO~(2-)的测定

采用电化学沉积法制备了负载Pt微粒和Fe(Ⅲ)的聚苯胺修饰玻碳电极(Pt-Fe(Ⅲ)/PAni/GCE)。通过循环伏安法研究了NO_2~-在该电极上的电化学行为,并优化了实验参数,在此基础上建立了一种用伏安法直接测定NO_2~-的方法。在酸性溶液中,NO_2~-的氧化峰电流与其浓度在5.0×10~(-7)～2.0×10~(-3)mol/L的范围内呈良好的线性关系,相关系数为0.999 6,检出限为4.0×10~(-7)mol/L。采用本方法测定NO_2~-具有较高的灵敏度和较好的重现性。     

Viscoelastic Characterization and Degradation Stability Investigation of Poly(butylene-adipate-co-terephthalate) – Calcium-Phosphate Glass Composites

Journal of Polymers and the Environment - In this work new biodegradable composite materials based on poly(butylene-adipate-co-terephthalate) (PBAT) reinforced with water-soluble calcium-phosphate...     

一种BiOCl_xBr_(1-x)/石墨烯微纳米复合光催化剂的制备方法

正该专利涉及一种BiOClxBr1-x/石墨烯微纳米复合光催化剂的制备方法。该光催化剂是以石墨烯为载体,负载有BiOClxBr1-x微纳米球的复合型光催化剂,其中Cl与Br的摩尔比为7∶3;对石墨烯表面进行BiOClxBr1-x微纳米球的负载改性,促进了光生电子从BiOClxBr1-x到石墨烯表面的迁移,制备的BiOClxBr1-x/石墨烯微纳米复合光催化剂具有高的紫外及可见光     

Environmental Degradation of Biodegradable Polyesters: 3. Effects of Alkali Treatment on Biodegradation of Poly(ε-Caprolactone) and Poly[(R)-3-Hydroxybutyrate) Films in Controled Soil

The poly(-caprolactone) (PCL) and poly[(R)-3-hydroxybutyrate] (R-PHB) films with a hydrophilic surface were prepared by the alkali treatment of their as-cast films in NaOH solutions of different concentrations. The alkali-treated PCL and R-PHB films, as well as the as-cast PCL and R-PHB films, were biodegraded in soil controlled at 25°C and the effects of alkali treatment or surface hydrophilicities on their biodegradation were investigated by the use of gravimetry, gel permeation chromatography (GPC), scanning electron microscopy (SEM), and polarization optical microscopy. It became evident that the alkali treatment enhanced the hydrophilicities and biodegradabilities of the PCL and R-PHB films in soil. The biodegradabilities of the as-cast aliphatic polyester films in controlled soil decreased in the following order: PCL > R-PHB > PLLA, in agreement with that in controlled static seawater.     

Synthesis of Poly(β-hydroxybutyrate) in Simulated Microgravity: An Investigation of Aeration Profiles in Shake Flask and Bioreactor

The microbial strain Azotobacter vinelandii UWD was grown under conditions of simulated microgravity in the National Aeronautics and Space Administration (NASA) Bioreactor. Bacterial growth in simulated microgravity differed significantly from that observed in conventional shake flask experiments: Cells tended to grow in a cluster-like pattern and polymer production started immediately after exposing them to conditions of simulated microgravity, and no lag time was observed. It was imperative to differentiate between the effects derived from microgravity and those imposed by the altered oxygen supply in the bioreactor. Aeration conditions were studied in both reactor types and a gas supply profile was developed for the bioreactor. This supply profile allowed for similar amounts of dissolved oxygen in the bioreactor and the shake flask in the initial stage of the fermentation and, therefore, for an evaluation of the effects of microgravity on biopolyester-producing bacteria. Since the optical density that is conventionally used as a measure for the cell growth could not be used due to the cluster-like growth pattern of the cells, it was determined that bacterial growth behavior in the bioreactor can be monitored through glucose or oxygen consumption.     

The Impact of the Macaíba Components Addition on the Biodegradation Acceleration of Poly (Ɛ-Caprolactone) (PCL)

Journal of Polymers and the Environment - Nowadays, there is a need to obtain eco-friendly materials, especially plastics that are responsible for most of the environmental pollution. In this...     

Compositional Limitations in Poly–3–Hydroxyalkanoates Produced by Pseudomonas oleovorans

It is well known that Pseudomonas oleovorans can utilize sodium octanoate for both cell growth and the synthesis of polyhydroxyalkanoates (PHAs), but it can utilize sodium butyrate only for limited cell growth and not for the polyester formation when this substrate is the sole carbon source. Therefore, these two substrates were evaluated as cofeeds for the possible incorporation of 3-hydroxybutyryl groups in the resulting PHA. When sodium butyrate and sodium octanoate were fed to P. oleovorans as cosubstrates in various proportions, the resultant cell density and polymer content were proportional to the amount of sodium octanoate in the feed. The PHA extracted from cells grown in all combinations of these cosubstrates had similar unit compositions of approximately 8 mole % 3-hydroxyhexanoate, 91 mole % 3-hydroxyoctanoate and 1 mole % 3-hydroxydecanoate. 3-Hydroxybutyrate units were not detected in any of the PHAs isolated, indicating that these units could not be incorporated in the copolymer synthesized by P. oleovorans either because the cell did not synthesize that monomer or, if it did, the PHA synthase could not copolymerize it with the longer chain monomers.     

Ag_6P_2W_(18)O_(62)/TiO_2/膨胀石墨复合光催化剂的制备及甲基橙的降解

以钛酸四丁酯为钛源、膨胀石墨(EG)为载体,通过溶胶凝胶-浸渍法制备了Ag_6P_2W_(18)O_(62)/TiO_2/EG复合光催化剂。采用SEM,EDS,XRD,FTIR,UV-vis等技术对其进行表征,研究了该催化剂在紫外光及可见光下对甲基橙的降解性能。表征结果显示:Ag_6P_2W_(18)O_(62)被成功负载到TiO_2上且保持Dawson结构;经Ag_6P_2W_(18)O_(62)表面修饰后的复合光催化剂可见光吸收性能增强;EG提供的丰富孔道有利于有机污染物吸附去除。实验结果表明:在甲基橙质量浓度为20 mg/L、催化剂加入量为1.0 g/L、反应温度为25℃的条件下,n(Ag)∶n(Ti)=1∶16时的复合光催化剂(ATE-2)的紫外光、可见光催化活性最佳;紫外光下反应70 min时甲基橙去除率为96.5%,可见光下反应40 h时甲基橙去除率为83.5%;ATE-2使用5次后,反应70 min时,其甲基橙去除率仍为92.5%。     

Thermoplastic Blends Based on Poly(Butylene Succinate-co-Adipate) and Different Collagen Hydrolysates from Tanning Industry—II: Aerobic Biodegradation in Composting Medium

Journal of Polymers and the Environment - Two different raw hydrolyzed collagens (HCs), by-products of the Tannery industry, were investigated in blends with a bioplastic, as poly(butylene...