Sources and characteristics of carbonaceous aerosols at Agra “World heritage site” and Delhi “capital city of India”

Agra, one of the oldest cities “World Heritage site”, and Delhi, the capital city of India are both located in the border of Indo-Gangetic Plains (IGP) and heavily loaded with atmospheric aerosols due to tourist place, anthropogenic activities, and its topography, respectively. Therefore, there is need for monitoring of atmospheric aerosols to perceive the scenario and effects of particles over northern part of India. The present study was carried out at Agra (AGR) as well as Delhi (DEL) during winter period from November 2011 to February 2012 of fine particulate (PM_2.5: d?<?2.5 μm) as well as associated carbonaceous aerosols. PM_2.5 was collected at both places using medium volume air sampler (offline measurement) and analyzed for organic carbon (OC) and elemental carbon (EC). Also, simultaneously, black carbon (BC) was measured (online) at DEL. The average mass concentration of PM_2.5 was 165.42?±?119.46 μg m^?3 at AGR while at DEL it was 211.67?±?41.94 μg m^?3 which is ~27 % higher at DEL than AGR whereas the BC mass concentration was 10.60 μg m^?3. The PM_2.5 was substantially higher than the annual standard stipulated by central pollution control board and United States Environmental Protection Agency standards. The average concentrations of OC and EC were 69.96?±?34.42 and 9.53?±?7.27 μm m^?3, respectively. Total carbon (TC) was 79.01?±?38.98 μg m^?3 at AGR, while it was 50.11?±?11.93 (OC), 10.67?±?3.56 μg m^?3 (EC), and 60.78?±?14.56 μg m^?3 (TC) at DEL. The OC/EC ratio was 13.75 at (AGR) and 5.45 at (DEL). The higher OC/EC ratio at Agra indicates that the formation of secondary organic aerosol which emitted from variable primary sources. Significant correlation between PM_2.5 and its carbonaceous species were observed indicating similarity in sources at both sites. The average concentrations of secondary organic carbon (SOC) and primary organic carbon (POC) at AGR were 48.16 and 26.52 μg m^?3 while at DEL it was 38.78 and 27.55 μg m^?3, respectively. In the case of POC, similar concentrations were observed at both places but in the case of SOC higher over AGR by 24 in comparison to DEL, it is due to the high concentration of OC over AGR. Secondary organic aerosol (SOA) was 42 % higher at AGR than DEL which confirms the formation of secondary aerosol at AGR due to rural environment with higher concentrations of coarse mode particles. The SOA contribution in PM_2.5 was also estimated and was ~32 and 12 % at AGR and DEL respectively. Being high loading of fine particles along with carbonaceous aerosol, it is suggested to take necessary and immediate action in mitigation of the emission of carbonaceous aerosol in the northern part of India.     

A review on recent progress in observations,sources, classification and regulations of PM<Subscript>2.5</Subscript> in Asian environments

Natural and human activities generate a significant amount of PM_2.5 (particles ≤2.5 μm in aerodynamic diameter) into the surrounding atmospheric environments. Because of their small size, they can remain suspended for a relatively longer time in the air than coarse particles and thus can travel long distances in the atmosphere. PM_2.5 is one of the key indicators of pollution and known to cause numerous types of respiratory and lung-related diseases. Due to poor implementation of regulations and a time lag in introducing the vehicle technology, levels of PM_2.5 in most Asian cities are much worse than those in European environments. Dedicated reviews on understanding the characteristics of PM_2.5 in Asian urban environments are currently missing but much needed. In order to fill the existing gaps in the literature, the aim of this review article is to describe dominating sources and their classification, followed by current status and health impact of PM_2.5, in Asian countries. Further objectives include a critical synthesis of the topics such as secondary and tertiary aerosol formation, chemical composition, monitoring and modelling methods, source apportionment, emissions and exposure impacts. The review concludes with the synthesis of regulatory guidelines and future perspectives for PM_2.5 in Asian countries. A critical synthesis of literature suggests a lack of exposure and monitoring studies to inform personal exposure in the household and rural areas of Asian environments.     

The impact of wood smoke on ambient PM2.5 in northern Rocky Mountain valley communities

During the winters of 2006/2007 and 2007/2008, PM_2.5 source apportionment programs were carried out within five western Montana valley communities. Filter samples were analyzed for mass and chemical composition. Information was utilized in a Chemical Mass Balance (CMB) computer model to apportion the sources of PM_2.5. Results showed that wood smoke (likely residential woodstoves) was the major source of PM_2.5 in each of the communities, contributing from 56% to 77% of the measured wintertime PM_2.5. Results of ¹⁴C analyses showed that between 44% and 76% of the measured PM_2.5 came from a new carbon (wood smoke) source, confirming the results of the CMB modeling. In summary, the CMB model results, coupled with the ¹⁴C results, support that wood smoke is the major contributor to the overall PM_2.5 mass in these rural, northern Rocky Mountain airsheds throughout the winter months.     

Concentration and characterization of airborne particles in Tehran’s subway system

Particulate matter is an important air pollutant, especially in closed environments like underground subway stations. In this study, a total of 13 elements were determined from PM₁₀ and PM_2.5 samples collected at two subway stations (Imam Khomeini and Sadeghiye) in Tehran’s subway system. Sampling was conducted in April to August 2011 to measure PM concentrations in platform and adjacent outdoor air of the stations. In the Imam Khomeini station, the average concentrations of PM₁₀ and PM_2.5 were 94.4?±?26.3 and 52.3?±?16.5 μg m^?3 in the platform and 81.8?±?22.2 and 35?±?17.6 μg m^?3 in the outdoor air, respectively. In the Sadeghiye station, mean concentrations of PM₁₀ and PM_2.5 were 87.6?±?23 and 41.3?±?20.4 μg m^?3 in the platform and 73.9?±?17.3 and 30?±?15 μg m^?3, in the outdoor air, respectively. The relative contribution of elemental components in each particle fraction were accounted for 43 % (PM₁₀) and 47.7 % (PM_2.5) in platform of Imam Khomeini station and 15.9 % (PM₁₀) and 18.5 % (PM_2.5) in the outdoor air of this station. Also, at the Sadeghiye station, each fraction accounted for 31.6 % (PM₁₀) and 39.8 % (PM_2.5) in platform and was 11.7 % (PM₁₀) and 14.3 % (PM_2.5) in the outdoor. At the Imam Khomeini station, Fe was the predominant element to represent 32.4 and 36 % of the total mass of PM₁₀ and PM_2.5 in the platform and 11.5 and 13.3 % in the outdoor, respectively. At the Sadeghiye station, this element represented 22.7 and 29.8 % of total mass of PM₁₀ and PM_2.5 in the platform and 8.7 and 10.5 % in the outdoor air, respectively. Other major crustal elements were 5.8 % (PM₁₀) and 5.3 % (PM_2.5) in the Imam Khomeini station platform and 2.3 and 2.4 % in the outdoor air, respectively. The proportion of other minor elements was significantly lower, actually less than 7 % in total samples, and V was the minor concentration in total mass of PM₁₀ and PM_2.5 in both platform stations.     

Concentrations and source apportionment of PM10 and associated elemental and ionic species in a lignite-burning power generation area of southern Greece

Ambient concentrations of PM₁₀ and associated elemental and ionic species were measured over the cold and the warm months of 2010 at an urban and two rural sites located in the lignite-fired power generation area of Megalopolis in Peloponnese, southern Greece. The PM₁₀ concentrations at the urban site (44.2?±?33.6 μg m^?3) were significantly higher than those at the rural sites (23.7?±?20.4 and 22.7?±?26.9 μg m^?3). Source apportionment of PM₁₀ and associated components was accomplished by an advanced computational procedure, the robotic chemical mass balance model (RCMB), using chemical profiles for a variety of local fugitive dust sources (power plant fly ash, flue gas desulfurization wet ash, feeding lignite, infertile material from the opencast mines, paved and unpaved road dusts, soil), which were resuspended and sampled through a PM₁₀ inlet onto filters and then chemically analyzed, as well as of other common sources such as vehicular traffic, residential oil combustion, biomass burning, uncontrolled waste burning, marine aerosol, and secondary aerosol formation. Geological dusts (road/soil dust) were found to be major PM₁₀ contributors in both the cold and warm periods of the year, with average annual contribution of 32.6 % at the urban site vs. 22.0 and 29.0 % at the rural sites. Secondary aerosol also appeared to be a significant source, contributing 22.1 % at the urban site in comparison to 30.6 and 28.7 % at the rural sites. At all sites, the contribution of biomass burning was most significant in winter (28.2 % at the urban site vs. 14.6 and 24.6 % at the rural sites), whereas vehicular exhaust contribution appeared to be important mostly in the summer (21.9 % at the urban site vs. 11.5 and 10.5 % at the rural sites). The highest contribution of fly ash (33.2 %) was found at the rural site located to the north of the power plants during wintertime, when winds are favorable. In the warm period, the highest contribution of fly ash was found at the rural site located to the south of the power plants, although it was less important (7.2 %). Moderate contributions of fly ash were found at the urban site (5.4 and 2.7 % in the cold and the warm period, respectively). Finally, the mine field was identified as a minor PM₁₀ source, occasionally contributing with lignite dust and/or deposited wet ash dust under dry summer conditions, with the summertime contributions ranging between 3.1 and 11.0 % among the three sites. The non-parametric bootstrapped potential source contribution function analysis was further applied to localize the regions of sources apportioned by the RCMB. For the majority of sources, source regions appeared as being located within short distances from the sampling sites (within the Peloponnesse Peninsula). More distant Greek areas of the NNE sector also appeared to be source regions for traffic emissions and secondary calcium sulfate dust.     

Source apportionment of PM2.5 for supporting control strategies in the Monterrey Metropolitan Area,Mexico

The Monterrey Metropolitan Area (MMA) in Northeast Mexico has shown high PM_2.5 concentrations since 2003. The data shows that the annual average concentration exceeds from 2 to 3 times the Mexican PM_2.5 annual air quality standard of 12 µg/m³. In a previous work we studied the chemical characterization of PM_2.5 in two sites of the MMA during the winter season. Among the most important components we found ammonium sulfate and nitrate, elemental and organic carbon, and crustal matter. In this work we present the results of a second chemical characterization study performed during the summer time and the application of the chemical mass balance (CMB) model to determine the source apportionment of air pollutants in the region. The chemical analysis results show that the chemical composition of PM_2.5 is similar in both sites and periods of the year. The results of the chemical analysis and the CMB model show that industrial, traffic, and combustion activities in the area are the major sources of primary PM_2.5 and precursor gases of secondary inorganic and organic aerosol (SO₂, NOx, NH₃, and volatile organic compounds [VOCs]). We also found that black carbon and organic carbon are important components of PM_2.5 in the MMA. These results are consistent with the MMA emission inventory that reports as major sources of particles and SO₂ a refinery and fuel combustion, as well as nitrogen oxides and ammonium from transportation and industrial activities in the MMA and ammonium form agricultural activities in the state. The results of this work are important to identify and support effective actions to reduce direct emissions of PM_2.5 and its precursor gases to improve air quality in the MMA. Implications: The Monterrey Metropolitan Area (MMA) has been classified as the most air-polluted area in Mexico by the World Health Organization (WHO). Effective actions need to be taken to control primary sources of PM_2.5 and its precursors, reducing health risks on the population exposed and their associated costs. The results of this study identify the main sources and their estimated contribution to PM_2.5 mass concentration, providing valuable information to the local environmental authorities to take decisions on PM_2.5 control strategies in the MMA.     

Concentrations of aliphatic and polycyclic aromatic hydrocarbons in ambient PM2.5 and PM10 particulates in Doha,Qatar

Organic carbon (OC), elemental carbon (EC), and 90 organic compounds (36 polycyclic aromatic hydrocarbons [PAHs], 25 n-alkane homologues, 17 hopanes, and 12 steranes) were concurrently quantified in atmospheric particulate matter of PM_2.5 and PM₁₀. The 24-hr PM samples were collected using Harvard Impactors at a suburban site in Doha, Qatar, from May to December 2015. The mass concentrations (mean ± standard deviation) of PM_2.5 and PM₁₀ were 40 ± 15 and 145 ± 70 µg m^?3, respectively, exceeding the World Health Organization (WHO) air quality guidelines. Coarse particles comprised 70% of PM₁₀. Total carbonaceous contents accounted for 14% of PM_2.5 and 10% of PM₁₀ particulate mass. The major fraction (90%) of EC was associated with the PM_2.5. In contrast, 70% of OC content was found in the PM_2.5–10 fraction. The secondary OC accounted for 60–68% of the total OC in both PM fractions, indicating photochemical conversions of organics are much active in the area due to higher air temperatures and solar radiations. Among the studied compounds, n-alkanes were the most abundant group, followed by PAHs, hopanes, and steranes. n-Alkanes from C₂₅ to C₃₅ prevailed with a predominance of odd carbon numbered congeners (C₂₇–C₃₁). High-molecular-weight PAHs (5–6 rings) also prevailed, within their class, with benzo[b + j]fluoranthene (Bb + jF) being the dominant member. PAHs were mainly (80%) associated with the PM_2.5 fraction. Local vehicular and fugitive emissions were predominant during low-speed southeasterly winds from urban areas, while remote petrogenic/biogenic emissions were particularly significant under prevailing northwesterly wind conditions.

Implications: An unprecedented study in Qatar established concentration profiles of EC, OC, and 90 organic compounds in PM_2.5 and PM₁₀. Multiple tracer organic compounds for each source can be used for convincing source apportionment. Particle concentrations exceeded WHO air quality guidelines for 82–96% of the time, revealing a severe problem of atmospheric PM in Doha. Dominance of EC and PAHs in fine particles signifies contributions from combustion sources. Dependence of pollutants concentrations on wind speed and direction suggests their significant temporal and spatial variability, indicating opportunities for improving the air quality by identifying sources of airborne contaminants.     

Source Apportionment of Particulate Matter (PM10) and Indoor Dust in a University Building

A study on source apportionment of indoor dust and particulate matter (PM₁₀) composition was conducted in a university building by using chemometrics. The objective of this study was to investigate the potential sources of selected heavy metals and ionic species in PM₁₀ and indoor dust. PM₁₀ samples were collected using a low-volume sampler (LVS) and indoor dust was collected using a soft brush. Inductively coupled plasma spectrometry (ICP-MS) was used to determine the concentration of heavy metals, while the concentration of cations and anions was determined by atomic absorption spectrometer (AAS) and ion chromatography (IC), respectively. The concentration of PM₁₀ recorded in the building throughout the sampling period ranged from 20 ± 10 μgm^?3 to 80 ± 33 μgm^?3. The composition of heavy metals in PM₁₀ and indoor dust were dominated by zinc (Zn), followed by lead (Pb), copper (Cu), and cadmium (Cd). Principle component analysis (PCA) and multiple linear regression (MLR) showed that the main sources of pollutants in PM₁₀ came from indoor renovations (73.83%), vehicle emissions (16.38%), earth crust sources (9.68%), and other outdoor sources (0.11%). For indoor dust, the pollutant source was mainly earth crust. This study suggests that chemometrics can be used for forensic investigation to determine the possible sources of indoor contaminants within a public building.     

Analysis of atmospheric aerosol (PM2.5) in Recife city,Brazil

Several studies indicate that mortality and morbidity can be well correlated to atmospheric aerosol concentrations with aerodynamic diameter less than 2.5 µm (PM_2.5). In this work the PM_2.5 at Recife city was analyzed as part of a main research project (INAIRA) to evaluate the air pollution impact on human health in six Brazilian metropolitan areas. The average concentration, for 309 samples (24-hr), from June 2007 to July 2008, was 7.3 µg/m³, with an average of 1.1 µg/m³ of black carbon. The elemental concentrations of samples were obtained by x-ray fluorescence. The concentrations were then used for characterizing the aerosol, and also were employed for receptor modelling to identify the major local sources of PM_2.5. Positive matrix factorization analysis indicated six main factors, with four being associated to soil dust, vehicles and sea spray, metallurgical activities, and biomass burning, while for a chlorine factor, and others related to S, Ca, Br, and Na, we could make no specific source association. Principal component analysis also indicated six dominant factors, with some specific characteristics. Four factors were associated to soil dust, vehicles, biomass burning, and sea spray, while for the two others, a chlorine- and copper-related factor and a nickel-related factor, it was not possible to do a specific source association. The association of the factors to the likely sources was possible thanks to meteorological analysis and sources information. Each model, although giving similar results, showed factors’ peculiarities, especially for source apportionment. The observed PM_2.5 concentration levels were acceptable, notwithstanding the high urbanization of the metropolitan area, probably due to favorable conditions for air pollution dispersion. More than a valuable historical register, these results should be very important for the next analysis, which will correlate health data, PM_2.5 levels, and sources contributions in the context of the six studied Brazilian metropolises.

Implications: The analysis of fine particulate matter (PM_2.5) in Recife city, Brazil, gave a significant picture of the local concentration and composition of this pollutant, which exhibits robust associations to adverse human health effects. Data from 1 year of sampling evaluated the seasonal variability and its connections with weather patterns. Source apportionment in this metropolitan area was obtained based in a combination of receptor models: principal component analysis (PCA)/chemical mass balance (CMB) and positive matrix factorization (PMF). These results give guidelines for local air pollution control actions, providing significant information for a health study in the context of establishing a new national air pollution protocol based on Brazilian cities data.     

Spatial differences in ambient coarse and fine particles in the Monterrey metropolitan area,Mexico: Implications for source contribution

The ambient air of the Monterrey Metropolitan Area (MMA) in Mexico frequently exhibits high levels of PM₁₀ and PM_2.5. However, no information exists on the chemical composition of coarse particles (PM_c = PM₁₀ – PM_2.5). A monitoring campaign was conducted during the summer of 2015, during which 24-hr average PM₁₀ and PM_2.5 samples were collected using high-volume filter-based instruments to chemically characterize the fine and coarse fractions of the PM. The collected samples were analyzed for anions (Cl^–, NO₃^–, SO₄^2–), cations (Na⁺, NH₄⁺, K⁺), organic carbon (OC), elemental carbon (EC), and 35 trace elements (Al to Pb). During the campaign, the average PM_2.5 concentrations did not showed significance differences among sampling sites, whereas the average PM_c concentrations did. In addition, the PM_c accounted for 75% to 90% of the PM₁₀ across the MMA. The average contribution of the main chemical species to the total mass indicated that geological material including Ca, Fe, Si, and Al (45%) and sulfates (11%) were the principal components of PM_c, whereas sulfates (54%) and organic matter (30%) were the principal components of PM_2.5. The OC-to-EC ratio for PM_c ranged from 4.4 to 13, whereas that for PM_2.5 ranged from 3.97 to 6.08. The estimated contribution of Secondary Organic Aerosol (SOA) to the total mass of organic aerosol in PM_2.5 was estimated to be around 70–80%; for PM_c, the contribution was lower (20–50%). The enrichment factors (EF) for most of the trace elements exhibited high values for PM_2.5 (EF: 10–1000) and low values for PM_c (EF: 1–10). Given the high contribution of crustal elements and the high values of EFs, PM_c is heavily influenced by soil resuspension and PM_2.5 by anthropogenic sources. Finally, the airborne particles found in the eastern region of the MMA were chemically distinguishable from those in its western region.

Implications: Concentration and chemical composition patterns of fine and coarse particles can vary significantly across the MMA. Public policy solutions have to be built based on these observations. There is clear evidence that the spatial variations in the MMA’s coarse fractions are influenced by clearly recognizable primary emission sources, while fine particles exhibit a homogeneous concentration field and a clear spatial pattern of increasing secondary contributions. Important reductions in the coarse fraction can come from primary particles’ emission controls; for fine particles, control of gaseous precursors—particularly sulfur-containing species and organic compounds—should be considered.     

Characterization of carbonaceous aerosols over Delhi in Ganga basin: seasonal variability and possible sources

The mass concentration of carbonaceous species, organic carbon (OC), and elemental carbon (EC) using a semicontinuous thermo-optical EC-OC analyzer, and black carbon (BC) using an Aethalometer were measured simultaneously at an urban mega city Delhi in Ganga basin from January 2011 to May 2012. The concentrations of OC, EC, and BC exhibit seasonal variability, and their concentrations were ～2 times higher during winter (OC 38.1?±?17.9 μg m^?3, EC 15.8?±?7.3 μg m^?3, and BC 10.1?±?5.3 μg m^?3) compared to those in summer (OC 14.1?±?4.3 μg m^?3, EC 7.5?±?1.5 μg m^?3, and BC 4.9?±?1.5 μg m^?3). A significant correlation between OC and EC (R?=?0.95, n?=?232) indicate their common emission sources with relatively lower OC/EC ratio (range 1.0–3.6, mean 2.2?±?0.5) suggests fossil fuel emission as a major source of carbonaceous aerosols over the station. On average, mass concentration of EC was found to be ～38 % higher than BC during the study period. The measured absorption coefficient (b_abs) was significantly correlated with EC, suggesting EC as a major absorbing species in ambient aerosols at Delhi. Furthermore, the estimated mass absorption efficiency (σ_abs) values are similar during winter (5.0?±?1.5 m² g^?1) and summer (4.8?±?2.8 m² g^?1). Significantly high aerosol loading of carbonaceous species emphasize an urgent need to focus on air quality management and proper impact assessment on health perspective in these regions.     

Determination of Microgram Quantities of Inorganic Sulfate in Atmospheric Particulates

Abstract

Before a community-wide woodstove changeout program, a chemical mass balance (CMB) source apportionment study was conducted in Libby, MT, during the winter of 2003–2004 to identify the sources of fine particulate matter (PM_2.5) within the valley. Results from this study showed that residential woodstoves were the major source, contributing approximately 80% of the ambient PM_2.5 throughout the winter months. In an effort to lower the ambient PM_2.5, a large woodstove changeout program was conducted in Libby from 2005 to 2007 in which nearly 1200 old woodstoves were changed out with cleaner burning models. During the winter of 2007–2008, a follow-up CMB source apportionment study was conducted to evaluate the effectiveness of the changeout. Results from this study showed that average winter PM_2.5 mass was reduced by 20%, and woodsmoke-related PM_2.5 (as identified by the CMB model) was reduced by 28% when compared with the pre-changeout winter of 2003– 2004. These results suggest that a woodstove changeout can be an effective tool in reducing ambient levels of PM_2.5 in woodstove-impacted communities.     

Organic and elemental carbon associated to PM10 and PM2.5 at urban sites of northern Greece

Organic carbon (OC) and elemental carbon (EC) concentrations, associated to PM₁₀ and PM_2.5 particle fractions, were concurrently determined during the warm and the cold months of the year (July–September 2011 and February–April 2012, respectively) at two urban sites in the city of Thessaloniki, northern Greece, an urban-traffic site (UT) and an urban-background site (UB). Concentrations at the UT site (11.3?±?5.0 and 8.44?±?4.08 14 μg m^?3 for OC₁₀ and OC_2.5 vs. 6.56?±?2.14 and 5.29?±?1.54 μg m^?3 for EC₁₀ and EC_2.5) were among the highest values reported for urban sites in European cities. Significantly lower concentrations were found at the UB site for both carbonaceous species, particularly for EC (6.62?±?4.59 and 5.72?±?4.36 μg m^?3 for OC₁₀ and OC_2.5 vs. 0.93?±?0.61 and 0.69?±?0.39 μg m^?3 for EC₁₀ and EC_2.5). Despite that, a negative UT-UB increment was frequently evidenced for OC_2.5 and PM_2.5 in the cold months possibly indicative of emissions from residential wood burning at the urban-background site. At both sites, cconcentrations of OC fractions were significantly higher in the cold months; on the contrary, EC fractions at the UT site were prominent in the warm season suggesting some influence from maritime emissions in the nearby harbor area. Secondary organic carbon, being estimated using the EC tracer method and seasonally minimum OC/EC ratios, was found to be an appreciable component of particle mass particularly in the cold season. The calculated secondary contributions to OC ranged between 35 and 59 % in the PM₁₀ fraction, with relatively higher values in the PM_2.5 fraction (39–61 %). The source origin of carbonaceous species was investigated by means of air parcel back trajectories, satellite fire maps, and concentration roses. A local origin was mainly concluded for OC and EC with limited possibility for long range transport of biomass (agricultural waste) burning aerosol.     

Chemical Composition and Source Apportionment of PM25 Particles in the Sihwa Area,Korea

ABSTRACT

To investigate the chemical characteristics of fine particles in the Sihwa area, Korea, atmospheric aerosol samples were collected using a dichotomous PM₁₀ sampler and two URG PM_2.5 cyclone samplers during five intensive sampling periods between February 1998 and February 1999. The Inductively Coupled Plasma (ICP)-Atomic Emission Spectrometry (AES)/ICP-Mass Spectrometry (MS), ion chromatograph (IC), and thermal manganese dioxide oxidation (TMO) methods were used to analyze the trace elements, ionic species, and carbonaceous species, respectively. Backward trajectory analysis, factor analysis, and a chemical mass balance (CMB) model were used to estimate quantitatively source contributions to PM_{2 5} particles collected in the Sihwa area.

The results of PM_2.5 source apportionment using the CMB7 receptor model showed that (NH₄)₂SO₄ was, on average, the major contributor to PM_2.5 particles, followed by nontraffic organic carbon (OC) emission, NH₄NO₃, agricultural waste burning, motor vehicle emission, road dust, waste incineration, marine aerosol, and others. Here, the nontraffic OC sources include primary anthropogenic OC emitted from the industrial complex zone, secondary OC, and organic species from distant sources. The source impact of waste incineration emission became significant when the dominant wind directions were from southwest and west sectors during the sampling periods. It was found that PM_2.5 particles in the Sihwa area were influenced mainly by both anthropogenic local sources and long-range transport and transformation of air pollutants.     

Monitoring and Source Apportionment of Particulate Matter near a Large Phosphorus Production Facility

ABSTRACT

A source apportionment study was conducted to identify sources within a large elemental phosphorus plant that contribute to exceedances of the National Ambient Air Quality Standards (NAAQS) for 24-hr PM₁₀. Ambient data were collected at three monitoring sites from October 1996 through July 1999, and included the following: 24-hr PM₁₀ mass, 24-hr PM_2.5 and PM_10–2.5 mass and chemistry, continuous PM₁₀and PM_2.5 mass, continuous meteorological data, and wind-direction-resolved PM_2.5 and PM₁₀ mass and chemistry. Ambient-based receptor modeling and wind-directional analysis were employed to help identify major sources or source locations and source contributions. Fine-fraction phosphate was the dominant species observed during PM₁₀ exceedances, though in general, re-suspended coarse dusts from raw and processed materials at the plant were also needed to create an exceedance. Major sources that were identified included the calciners, the CO flares, process-related dust, and electric-arc furnace operations.     

Estimation of source apportionment and potential source locations of PM2.5 at a west coastal IMPROVE site

Particle composition data for PM_2.5 samples collected at Kalmiopsis Interagency Monitoring of Protected Visual Environments (IMPROVE) site in southwestern Oregon from March 2000 to May 2004 were analyzed to provide source identification and apportionment. A total of 493 samples were collected and 32 species were analyzed by particle induced X-ray emission, proton elastic scattering analysis, photon-induced X-ray fluorescence, ion chromatography, and thermal optical reflectance methods. Positive matrix factorization (PMF) was used to estimate the source profiles and their mass contributions. The PMF modeling identified nine sources. In the Kalmiopsis site, the average mass was apportioned to wood/field burning (38.4%), secondary sulfate (26.9%), airborne soil including Asian dust (8.6 %), secondary nitrate (7.6%), fresh sea salt (5.8%), OP-rich sulfate (4.9%), aged sea salt (4.5 %), gasoline vehicle (1.9%), and diesel emission (1.4%). The potential source contribution function (PSCF) was then used to help identify likely locations of the regional sources of pollution. The PSCF map for wood/field burning indicates there is a major potential source area in the Siskiyou County and eastern Oregon. The potential source locations for secondary sulfate are found in western Washington, northwestern Oregon, and the near shore Pacific Ocean where there are extensive shipping lanes. It was not possible to extract a profile directly attributable to ship emissions, but indications of their influence are seen in the secondary sulfate and aged sea salt compositions.     

Source apportionment of fine particles utilizing partially speciated carbonaceous aerosol data at two rural locations in New York State

A source apportionment study was conducted at two rural locations, Potsdam and Stockton, to assess the in-state/out-of-state sources of PM_2.5 and Hg in New York State. At both locations, samples were collected between November 2002 and August 2005 and analyzed for fine PM mass and its chemical constituents. The measured chemical constituents included elements, cations, anions, organic and elemental carbon (OC and EC), black carbon (BC), and water-soluble short-chain (WSSC) organic acids. Positive matrix factorization (PMF) was applied to the measured concentrations and eight and seven factors were resolved at Potsdam and Stockton, respectively. Four factors were resolved in common between the two locations including secondary sulfate, secondary nitrate, secondary OC, and a crustal factor. The factor profiles of mixed industrial and motor vehicle factors resolved at Potsdam were different compared with the corresponding profiles for these factors at Stockton. A resuspended road salt factor was identified at Potsdam, while an aged sea salt factor was identified at Stockton. At Potsdam, a wood smoke factor was also resolved. Among the resolved factors, secondary sulfate was the highest contributor to the measured mass at both sites. Potential source contribution function (PSCF) analysis indicated the Ohio River Valley region as a common potential source region for this factor at both locations. For the secondary nitrate factor, at Potsdam PSCF analysis indicated the Midwestern US (NO_x emissions), and the US farm belt (ammonia emissions) as potential source regions, while at Stockton, the Midwestern US (power plant NO_x emissions) was indicated as a major potential source region.     

Wintertime PM2.5 and PM10 Source Apportionment at Sacramento,California

ABSTRACT

The chemical mass balance (CMB) model was applied to winter (November through January) 1991–1996 PM2.5 and PM10 data from the Sacramento 13th and T Streets site in order to identify the contributions from major source categories to peak 24-hr ambient PM_2.5 and PM₁₀ levels. The average monthly PM₁₀ monitoring data for the nine-year period in Sacramento County indicate that elevated concentrations are typical in the winter months. Concentrations on days of highest PM₁₀ are dominated by the PM2.5 fraction. One factor contributing to increased PM_2.5 concentrations in the winter is meteorology (cool temperatures, low wind speeds, low inversion layers, and more humid conditions) that favors the formation of secondary nitrate and sulfate aerosols. Residential wood burning also elevates fine particulate concentrations in the Sacramento area.

The results of the CMB analysis highlight three key points. First, the source apportionment results indicate that primary motor vehicle exhaust and wood smoke are significant sources of both PM_2.5 and PM₁₀ in winter. Second, nitrates, secondarily formed as a result of motor-vehicle and other sources of nitrogen oxide (NO_x), are another principal cause of the high PM_2.5 and PM₁₀ levels during the winter months. Third, fugitive dust, whether it is resuspended soil and dust or agricultural tillage, is not the major contributor to peak winter PM_2.5 and PM10 levels in the Sacramento area.     

Determination of sources of fine particles in different ambient atmospheres in South Korea using a chemical mass balance model

Abstract

To determine the sources of particulate matter less than 2.5?μm (PM_2.5 in different ambient atmospheres (urban, roadside, industrial, and rural sites), the chemical components of PM_2.5 such as ions (Cl^-, NO₃^-, SO₄^2-, NH₄⁺, Na⁺, K⁺, Ca²⁺, and Mg²⁺), carbonaceous species, and elements (Al, As, Ba, Cd, Cu, Fe, Mn, Ni, Pb, Se, V, and Zn) were measured. The average mass concentrations of PM_2.5 at the urban, roadside, industrial, and rural sites were 31.5?±?14.8, 31.6?±?22.3, 31.4?±?16.0, and 25.8?±?12.4?μg/m³, respectively. Except for secondary ammonium sulfate and ammonium nitrate, the model results showed that the traffic source (i.e., the sum of gasoline and diesel vehicle sources) was the most dominant source of PM_2.5 (17.1%) followed by biomass burning (13.8%) at the urban site. The major primary sources of PM_2.5 were consistent with the site characteristics (diesel vehicle source at the roadside site, coal-fired plants at the industrial site, and biomass burning at the rural site). Seasonal data from the urban site suggested that ammonium sulfate and ammonium nitrate were the most dominant sources of PM_2.5 during all seasons. Further, the contribution of road dust source to PM_2.5 increased during spring and fall seasons. We conclude that the determination of the major PM_2.5 sources is useful for establishing efficient control strategies for PM_2.5 in different regions and seasons.     

Characteristics of water-soluble inorganic ions in PM2.5 and PM2.5–10 in the coastal urban agglomeration along the Western Taiwan Strait Region,China

PM_2.5 and PM_2.5–10 aerosol samples were collected in four seasons during November 2010, January, April, and August 2011 at 13 urban/suburban sites and one background site in Western Taiwan Straits Region (WTSR), which is the coastal area with rapid urbanization, high population density, and deteriorating air quality. The 10 days average PM_2.5 concentrations were 92.92, 51.96, 74.48, and 89.69 μg/m³ in spring, summer, autumn, and winter, respectively, exceeding the Chinese ambient air quality standard for annual average value of PM_2.5 (grade II, 35 μg/m³). Temporal distribution of water-soluble inorganic ions (WSIIs) in PM_2.5 was coincident with PM_2.5 mass concentrations, showing highest in spring, lowest in summer, and middle in autumn and winter. WSIIs took considerable proportion (42.2～50.1 %) in PM_2.5 and PM_2.5–10. Generally, urban/suburban sites had obviously suffered severer pollution of fine particles compared with the background site. The WSIIs concentrations and characteristics were closely related to the local anthropogenic activities and natural environment, urban sites in cities with higher urbanization level, or sites with weaker diffuse condition suffered severer WSIIs pollution. Fossil fuel combustion, traffic emissions, crustal/soil dust, municipal constructions, and sea salt and biomass burnings were the major potential sources of WSIIs in PM_2.5 in WTSR according to the result of principal component analysis.