Cu sorption on Phragmites australis leaf and stem litter: a kinetic study

Decaying organic matter plays an important role in the cycling of metals in wetland ecosystems. Sorption kinetics of Cu(II) on Phragmites australis leaf and stem litter were studied. Fresh leaf and stem litter was sampled from a surface flow wetland at the end of the growing season. The effect of decomposition stage was studied with litter that had been decomposing for a period of 5 months. The Lagergren pseudo-first-order model, the pseudo-second-order model, the Elovich equation and two diffusion models based on spherical intra-particle diffusion were fitted to the experimental data. The sorption capacity was significantly affected by the decomposition of the litter. The sorption process was best described by the pseudo-second-order kinetics (R(2) approximately 0.99) but the rate constant was strongly dependent on the initial Cu concentration. The intra-particle diffusion model fitted the data only slightly less (R(2)>0.95) than the pseudo-second-order model. A theoretical comparison revealed that the good fit with the pseudo-second-order kinetics could be indicative of intra-particle diffusion. Sorption kinetics observed for the leaf and stem litter at different metal concentrations showed a fast initial sorption followed by a slow sorption phase.     

改性甘蔗渣对Cu2+和Zn2+的吸附机理

研究了均苯四甲酸二酐(PMDA)和乙二胺四乙酸二酐(EDTAD)改性甘蔗渣对重金属离子Cu2+和Zn2+的吸附性能,包括吸附动力学和吸附等温线。结果表明,改性后的甘蔗渣对重金属离子Cu2+和Zn2+的吸附容量有显著提高,对Cu2+和Zn2+吸附等温线均符合Langmuir方程,吸附为单分子层吸附。根据Langmuir方程,PMDA和EDTAD改性甘蔗渣对Cu2+的吸附量分别为60.21和33.45 mg/g,对Zn2+的吸附量分别是70.53和36.53 mg/g。两种改性甘蔗渣对两种金属离子的吸附在30 min内均可完成,用准二级吸附动力学方程模拟动力学过程得到较好的线性相关性。以EDTA溶液为洗脱剂对吸附Cu2+和Zn2+的改性甘蔗渣进行洗脱再生,再生的吸附剂可反复使用。     

改性甘蔗渣对Cu^2＋和Zn^2＋的吸附机理

研究了均苯四甲酸二酐（PMDA）和乙二胺四乙酸二酐（EDTAD）改性甘蔗渣对重金属离子Cu^2＋和Zn^2＋的吸附性能，包括吸附动力学和吸附等温线。结果表明，改性后的甘蔗渣对重金属离子Cu^2＋和Zn^2＋的吸附容量有显著提高，对Cu^2＋和Zn^2＋吸附等温线均符合Langmuir方程，吸附为单分子层吸附。根据Langmuir方程，PMDA和EDTAD改性甘蔗渣对Cu^2＋的吸附量分别为60．21和33．45mg／g，对Zn^2＋的吸附量分别是70．53和36．53mg／g。两种改性甘蔗渣对两种金属离子的吸附在30min内均可完成，用准二级吸附动力学方程模拟动力学过程得到较好的线性相关性。以EDTA溶液为洗脱剂对吸附Cu^2＋和Zn^2＋的改性甘蔗渣进行洗脱再生，再生的吸附剂可反复使用。     

Kinetic and isotherm error optimization studies for adsorption of atrazine and imidacloprid on bark of Eucalyptus tereticornis L.

The aim of this study was to establish the bark of Eucalyptus tereticornis L. (EB) as a low cost bio-adsorbent for the removal of imidacloprid and atrazine from aqueous medium. The pseudo-first-order (PFO), pseudo-second-order (PSO), Elovich and intra-particle diffusion (IPD) models were used to describe the kinetic data and rate constants were evaluated. Adsorption data was analysed using ten 2-, 3- and 4-parameter models viz. Freundlich, Jovanovic, Langmuir, Temkin, Koble–Corrigan, Redlich–Peterson, Sips, Toth, Radke–Prausnitz, and Fritz-Schluender isotherms. Six error functions were used to compute the best fit single component isotherm parameters by nonlinear regression analysis. The results showed that the sorption of atrazine was better explained by PSO model, whereas the sorption of imidacloprid followed the PFO kinetic model. Isotherm model optimization analysis suggested that the Freundlich along with Koble–Corrigan, Toth and Fritz-Schluender were the best models to predict atrazine and imidacloprid adsorption onto EB. Error analysis suggested that minimization of chi-square (χ²) error function provided the best determination of optimum parameter sets for all the isotherms.     

Adsorption of multi-heavy metals Zn and Cu onto surficial sediments: modeling and adsorption capacity analysis

Improved multiple regression adsorption models (IMRAMs) was developed to estimate the adsorption capacity of the components [Fe oxides (Fe), Mn oxides (Mn), organic materials (OMs), residuals] in surficial sediments for multi-heavy metal Zn and Cu. IMRAM is an improved version over MRAM, which introduces a computer program in the model developing process. As MRAM, Zn(Cu) IMRAM, and Cu(Zn) IMRAM again confirmed that there is significant interaction effects that control the adsorption of compounded Zn and Cu, which was neglected by additional adsorption model. The verification experiment shows that the relative deviation of the IMRAMs is less than 13 %. It is revealed by the IMRAMs that Mn, which has the greatest adsorption capability for compounded Zn and Cu (54.889 and 161.180 mg/l, respectively), follows by interference adsorption capacity of Fe/Mn (?1.072 and ?24.591 mg/l respectively). Zn and Cu influence each other through different mechanisms. When Zn is the adsorbate, compounded Cu mainly affects the adsorption capacities of Fe/Mn and Fe/Mn/OMs; while when Cu is the adsorbate, compounded Zn mainly exerts its effect on Mn, Fe/Mn, and Mn/OMs. It also shows that the compounded Zn or Cu weakened the interference adsorption of Fe/Mn, and meanwhile, strengthened the interference adsorption of Mn/OMs.     

粉煤灰砖块对磷酸盐的吸附特性

以建筑废料粉煤灰砖块为吸附剂材料,通过静态吸附实验研究其对磷酸盐的吸附特征,以及磷酸盐初始浓度、吸附剂投加量、pH等因素对吸附反应的影响。Langmuir、Freundlich和Temkin等温模型的分析发现,Langmuir等温式方程最适合描述吸附过程,对磷酸盐的理论饱和吸附容量为44.62 mg/g。利用伪一级动力学模型、伪二级动力学模型和颗粒内扩散模型考察了吸附过程特征,其中伪二级动力学模型为最适于描述粉煤灰砖块对磷酸盐的吸附过程的动力学模型。通过颗粒内扩散模型、Bangham方程及Boyd模型对吸附动力学机理进行的探讨表明,颗粒内扩散速率不是粉煤灰砖块吸附磷酸盐反应的惟一速率控制步,膜扩散速率和颗粒内扩散速率共同影响着吸附反应速率。磷酸盐浓度较低时主要是膜扩散限制吸附反应速率,而磷酸盐浓度较高时则颗粒内扩散成为速率控制步。研究证明,粉煤灰砖块粉末作为湿地基质具有对磷酸盐很强的吸附能力,在减少了固体废弃物的数量的同时又可以实现水污染控制的目的。     

Adsorption characteristics of Cu(II) from aqueous solution onto biochar derived from swine manure

The purpose of this study was to investigate adsorption characteristic of swine manure biochars pyrolyzed at 400 °C and 700 °C for the removal of Cu(II) ions from aqueous solutions. The biochars were characterized using BET surface area, Fourier transform infrared spectroscopy (FTIR), zeta potential, scanning electron microscopy/energy dispersive spectrometer (SEM–EDS), and X-ray diffraction (XRD). The adsorption of Cu(II) ions by batch method was carried out and the optimum conditions were investigated. The adsorption processes of these biochars are well described by a pseudo-second-order kinetic model, and the adsorption isotherm closely fitted the Sips model. Thermodynamic analysis suggested that the adsorption was endothermic. The maximum Cu(II) adsorption capacities of biochars derived from fresh and composted swine manure at 400 °C were 17.71 and 21.94 mg g^?1, respectively, which were higher than those at 700 °C. XRD patterns indicated that the silicate and phosphate particles within the biochars served as adsorption sites for Cu(II). The removal of Cu(II) ions from industrial effluent indicated that the fresh swine manure biochar pyrolyzed at 400 °C can be considered as an effective adsorbent.     

Kinetic, equilibrium isotherm and thermodynamic studies of Cr(VI) adsorption onto low-cost adsorbent developed from peanut shell activated with phosphoric acid

A particular agricultural waste, peanut shell, has been used as precursor for activated carbon production by chemical activation with H₃PO₄. Unoxidized activated carbon was prepared in nitrogen atmosphere which was then heated in air at a desired temperature to get oxidized activated carbon. The prepared carbons were characterized for surface area, surface morphology, and pore volume and utilized for the removal of Cr(VI) from aqueous solution. Batch mode experiments were conducted to study the effects of pH, contact time, particle size, adsorbent dose, initial concentration of adsorbate, and temperature on the adsorption of Cr(VI). Cr(VI) adsorption was significantly dependent on solution pH, and the optimum adsorption was observed at pH 2. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were used to analyze the kinetic data obtained at different initial Cr(VI) concentrations. The adsorption kinetic data were described very well by the pseudo-second-order model. Equilibrium isotherm data were analyzed by the Langmuir, Freundlich, and Temkin models. The results showed that the Langmuir adsorption isotherm model fitted the data better in the temperature range studied. The adsorption capacity which was found to increase with temperature showed the endothermic nature of Cr(VI) adsorption. The thermodynamic parameters, such as Gibb’s Free energy change (ΔG°), standard enthalpy change (ΔH°), and standard entropy change (ΔS°) were evaluated.     

Preparation and characterization of surfactant-modified hydroxyapatite/zeolite composite and its adsorption behavior toward humic acid and copper(II)

A novel composite material, i.e., surfactant-modified hydroxyapatite/zeolite composite, was used as an adsorbent to remove humic acid (HA) and copper(II) from aqueous solution. Hydroxyapatite/zeolite composite (HZC) and surfactant-modified HZC (SMHZC) were prepared and characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and field emission scanning electron microscope. The adsorption of HA and copper(II) on SMHZC was investigated. For comparison purposes, HA adsorption onto HZC was also investigated. SMHZC exhibited much higher HA adsorption capacity than HZC. The HA adsorption capacity for SMHZC decreased slightly with increasing pH from 3 to 8 but decreased significantly with increasing pH from 8 to 12. The copper(II) adsorption capacity for SMHZC increased with increasing pH from 3 to 6.5. The adsorption kinetic data of HA and copper(II) on SMHZC obeyed a pseudo-second-order kinetic model. The adsorption of HA and copper(II) on SMHZC took place in three different stages: fast external surface adsorption, gradual adsorption controlled by both film and intra-particle diffusions, and final equilibrium stage. The equilibrium adsorption data of HA on SMHZC better fitted to the Langmuir isotherm model than the Freundlich isotherm model. The equilibrium adsorption data of copper(II) on SMHZC could be described by the Langmuir, Freundlich, and Dubinin–Radushkevich isotherm models. The presence of copper(II) in solution enhanced HA adsorption onto SMHZC. The presence of HA in solution enhanced copper(II) adsorption onto SMHZC. The mechanisms for the adsorption of HA on SMHZC at pH 7 may include electrostatic attraction, organic partitioning, hydrogen bonding, and Lewis acid–base interaction. The mechanisms for the adsorption of copper(II) on SMHZC at pH 6 may include surface complexation, ion exchange, and dissolution–precipitation. The obtained results indicate that SMHZC can be used as an effective adsorbent to simultaneously remove HA and copper(II) from water.     

Arsenic sorption by red mud-modified biochar produced from rice straw

Red mud-modified biochar (RM-BC) has been produced to be utilized as a novel adsorbent to remove As because it can effectively combine the beneficial features of red mud (rich metal oxide composition and porous structure) and biochar (large surface area and porous structure properties). SEM-EDS and XRD analyses demonstrated that red mud had loaded successfully on the surface of biochar. With the increasing of pH in solution, arsenate (As(V)) adsorption on RM-BC decreased while arsenite (As(III)) increased. Arsenate adsorption kinetics process on RM-BC fitted the pseudo-second-order model, while that of As(III) favored the Elovich model. All sorption isotherms produced superior fits with the Langmuir model. RM-BC exhibited improved As removal capabilities, with a maximum adsorption capacity (Q_max) for As(V) of 5923 μg g^?1, approximately ten times greater than that of the untreated BC (552.0 μg g^?1). Furthermore, it has been indicated that the adsorption of As(V) on RM-BC may be strongly associated with iron oxides (hematite and magnetite) and aluminum oxides (gibbsite) by X-ray absorption near-edge spectroscopy (XANES), which was possibly because of surface complexation and electrostatic interactions. RM-BC may be used as a valuable adsorbent for removing As in the environment due to the waste materials being relatively abundant.     

Sorption kinetics and isotherm modelling of imidacloprid on bentonite and organobentonites

Bentonite was modified by quaternary ammonium cations viz. cetytrimethylammonium (CTA), cetylpyridinium (CP), rioctylmethylammonium (TOM) and pcholine (PTC) at 100% cation exchange capacity of bentonite and was characterized by X-ray diffraction, CHNS elemental analyser and Fourier transform infrared spectroscopy. The sorption of imidacloprid on organobentonites/bentonite was studied by batch method. Normal bentonite could adsorb imidacloprid only upto 19.31–22.18% while all organobentonites except PTC bentonite (PTCB), enhanced its adsorption by three to four times. Highest adsorption was observed in case of TOM bentonite (TOMB) (76.94–83.16%). Adsorption kinetic data were fitted to pseudo-first-order, pseudo-second-order and intraparticle diffusion models. For normal bentonite data were best fitted to pseudo-first-order kinetic, while for organobentonites fitted to pseudo-second-order kinetics. Sorption data were analysed using Freundlich, Langmuir, Temkin and Dubinin–Radushkevich isotherm models. Data were well fitted to Freundlich adsorption isotherm. Product of Freundlich adsorption constant and heterogeneity parameter (K_f.1/n) was in following order: TOMB (301.87) > CTA bentonite (CTAB) (152.12) > CP bentonite (CPB) (92.58) > bentonite (27.25). Desorption study confirmed hysteresis and concentration dependence. The present study showed that the organobentonite could be a good sorbent for removal of imidacloprid from natural water sample also. Percentage adsorption and Distribution coefficient (mL g^?1) value of different adsorbent was in following order: TOMB (74.85% and 297.54) > CTAB (55.78% and 126.15) > CPB (45.81% and 84.55) > bentonite (10.65% and 11.92).     

粉煤灰微波改性及其对Cr~（6＋）的吸附特性

将粉煤灰（fly ash,FA）微波辐照制得微波改性粉煤灰（MFA）,选择用H2SO4、NaOH和Ca（OH）2对MFA进行化学改性制得微波化学改性粉煤灰（MMFA）,结果表明,用2 mol/L NaOH并按与MFA的质量体积比为1∶4制得的MMFA对Cr6＋的吸附去除效果最好,与原灰相比,去除率显著增强。研究了NaOH改性MMFA对废水中Cr6＋的吸附性能。动力学研究结果表明,MMFA对Cr6＋的吸附动力学符合二级吸附动力学速率方程,吸附受颗粒内扩散过程控制。热力学研究结果表明,在25、35和45℃下MMFA对Cr6＋的等温吸附行为均可用Langmuir方程、Freundlich方程和线性方程描述,所得热力学参数吸附自由能（ΔG）、吸附焓（ΔH）和吸附熵（ΔS）均为负值,说明MMFA对Cr6＋的吸附过程为自发进行的放热吸附过程。     

Thermodynamic analysis of fatty acid harvesting by novel carbon-based adsorbent

In this study, separation and concentration of fatty acids (FA) from the synthetic food processing wastewater containing low concentration of FA (250 mg/L) were investigated using expanded graphite (EG) as a novel adsorbent at different temperatures (298~318 K). The adsorption results were further analyzed to verify adsorption mechanisms and thermodynamics of FA onto EG. Results show that the adsorption of FA onto EG was explained well by the Langmuir model with the maximum adsorption capacity up to 8.01 g FA/g EG at 298 K, and considerably affected by temperature. The adsorption kinetics fitted with pseudo-second-order kinetic model and the adsorption mechanism analysis showed that the intraparticle diffusion was not the rate-limiting step, but the coalescence of FA droplets played the significant role for novel adsorption of FA onto EG. The calculated activation energy and thermodynamic parameters such as Gibbs free energy change (ΔG⁰), enthalpy change (ΔH⁰), and entropy change (ΔS⁰) indicated that the adsorption of FA onto EG was very feasible, was highly spontaneous, occurred physically, was exothermic in nature, and was stable in aquatic environmental changes. Overall, FA can be effectively harvested and concentrated from the food processing wastewater by EG even at low concentration.     

Upgraded modified forms of bituminous coal for the removal of safranin-T dye from aqueous solution

Natural bituminous coal was used as a precursor in the synthesis of different modified products. The modification of coal was performed by treating it with nitric acid (N-coal), coating its surface by zinc oxide nanoparticles (Z-coal), and converting it into porous graphite (PG). The effect of modification processes on the structures, morphologies, and optical properties was followed by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectrum (FT-IR), and UV/VIS spectrophotometer analysis. The surface of N-coal grains becomes smoother than the surface of raw coal grains due to the removal of the associated impurities and the formation of nitrogen function groups. For Z-coal, the whole surface of coal grains appears to be completely covered by agglomerated ZnO nanoparticles of massive density and irregular shapes. The average crystallite size of the formed ZnO is ~22.2 nm and density of dislocations is 2.029 × 10^?3 dislocation/nm². Also, the removal of safranin-T dye by natural bituminous coal and its modified forms was investigated as a function of contact time, adsorbent mass, initial dye concentration, and pH value. At pH 8, the PG showed higher efficiency (96%) than Z-coal (93.5%), N-coal (74.5%), and natural coal (62%) after 2 h for 0.1 g on 100 mg/L dye. The obtained results are well fitted by pseudo-second-order kinetic than by intraparticle diffusion and Elovich kinetic models for the adsorption by N-coal, Z-coal, and PG, whereas the adsorption by raw coal is well fitted with both pseudo-second-order and Elovich kinetic models. The Langmuir isotherm model fits well the equilibrium adsorption isotherm of safranin by raw coal and its modified forms. The values of maximum adsorption capacity were calculated for raw coal, N-coal, Z-coal, and PG to be 21.3, 27.4, 32.46, and 33.67 mg/g, respectively. A monolayer model with one energy and a monolayer model with two energies as advanced equilibrium models were investigated for more physical interpretation of the adsorption process. The calculated parameters (number of adsorbed molecules per site and number of receptor sites per unit mass) reflected the role of modification processes in the adsorption behavior of safranin.

Open image in new window

Graphical abstract High volatile bituminous coal and its modified forms have been used for the removal of Safranin-T dye from aqueous solution.

     

Biosorption of Cr(VI) and Zn(II) ions from aqueous solution onto the solid biodiesel waste residue: mechanistic, kinetic and thermodynamic studies

In this present study, the biosorption of Cr(VI) and Zn(II) ions from synthetic aqueous solution on defatted J atropha oil cake (DJOC) was investigated. The effect of various process parameters such as the initial pH, adsorbent dosage, initial metal ion concentration and contact time has been studied in batch-stirred experiments. Maximum removal of Cr(VI) and Zn(II) ions in aqueous solution was observed at pH 2.0 and pH. 5.0, respectively. The removal efficiency of Cr(VI) and Zn(II) ions from the aqueous solution was found to be 72.56 and 79.81 %, respectively, for initial metal ion concentration of 500 mg/L at 6 g/L dosage concentration. The biosorbent was characterized by Fourier transform infrared, scanning electron microscopy and zero point charge. Equilibrium data were fitted to the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models and the best fit is found to be with the Freundlich isotherm for both Cr(VI) and Zn(II) metal ions. The kinetic data obtained at different metal ion concentration have been analysed using the pseudo-first-order, pseudo-second-order and intraparticle diffusion models and were found to follow the pseudo-second-order kinetic model. The values of mass transfer diffusion coefficients (D _e) were determined by Boyd model and compared with literature values. Various thermodynamic parameters, such as ΔG°, ΔH° and ΔS°, were analysed using the equilibrium constant values (K _e) obtained from experimental data at different temperatures. The results showed that biosorption of Cr(VI) and Zn(II) ions onto the DJOC system is more spontaneous and exothermic in nature. The results indicate that DJOC was shown to be a promising adsorbent for the removal of Cr(VI) and Zn(II) ions from aqueous solution.     

The removal of uranium (VI) from aqueous solutions onto activated carbon developed from grinded used tire

In this study, activated carbon was prepared from waste tire by KOH chemical activation. The pore properties including the BET surface area, pore volume, pore size distribution, and average pore diameter were characterized. BET surface area of the activated carbon was determined as 558 m²/g. The adsorption of uranium ions from the aqueous solution using this activated carbon has been investigated. Various physico-chemical parameters such as pH, initial metal ion concentration, and adsorbent dosage level and equilibrium contact time were studied by a batch method. The optimum pH for adsorption was found to be 3. The removal efficiency has also been determined for the adsorption system as a function of initial concentration. The experimental results were fitted to Langmuir, Freundlich, and Dubinin–Radushkevich (D-R) isotherm models. A comparison of best-fitting was performed using the coefficient of correlation and the Langmuir isotherm was found to well represent the measured sorption data. According to the evaluation using the Langmuir equation, the saturated monolayer sorption capacity of uranium ions onto waste tire activated carbon was 158.73 mg/g. The thermodynamic equilibrium constant and the Gibbs free energy were determined and results indicated the spontaneous nature of the adsorption process. Kinetics data were best described by pseudo-second-order model.     

生物沸石球强化吸附氨氮废水的动力学研究

用一种具有多孔结构特征的沸石球作为载体固定化硝化细菌强化吸附氨氮废水。结果表明,沸石球能快速固定化硝化细菌,吸附动力学表明150 min对氨氮吸附容量达到2.816 mg/g,而且还有继续增加的趋势。假二级动力学方程和Elovich模型的精确拟合说明,生物沸石球对氨氮的吸附过程可能是非均相扩散起作用及以化学吸附反应为主的复杂转化过程。扩散拟合结果表明,氨氮在生物沸石球的吸附是以液膜扩散和颗粒内扩散为吸附速率的控制步骤,活性的硝化细菌对氨氮的硝化使氨氮在微孔的吸附得到了强化。     

The role of Mn oxide doping in phosphate removal by Al-based bimetal oxides: adsorption behaviors and mechanisms

This study investigated the behaviors and mechanisms of phosphate adsorbed onto manganese (Mn) oxide-doped aluminum (Al) oxide (MODAO). The isotherm results demonstrated that the maximum amount of phosphorus (P) adsorbed onto MODAO was 59.8 mg/g at T?=?298 K (pH 6.0). This value was nearly twice the amount of singular AlOOH and could increase with rising temperatures. The kinetic results illustrated that most of the P was adsorbed onto MODAO within 5 h, which was shorter than the equilibrium time of phosphate adsorption onto AlOOH. The Elovich model effectively described the adsorption kinetic data of MODAO because of its heterogeneous surface. The optimal solution pH for phosphate removal was approximately 5.0 because of electrostatic interaction effects. Meanwhile, the decrease in P uptake with increasing ion strength suggested that phosphate adsorption occurred through an outer-sphere complex. Phosphates would compete for adsorption sites on the surface of MODAO in the presence of fluoride ion or sulfate. In addition, the spectroscopic analysis results of Fourier transform infrared spectroscopy and X-ray photoemission spectroscopy indicated that removal mechanisms of phosphate primarily include adhesion to surface hydroxyl groups and ligand exchange.     

颗粒羟基氧化锆的除氟性能

以羟基氧化锆粉末为原料,制备颗粒羟基氧化锆,评价了颗粒羟基氧化锆对溶液中F-的吸附性能。结果表明:颗粒羟基氧化锆除氟过程符合Freundlich吸附等温线模型和拟二级动力学模型,F-的吸附过程包括液膜扩散和颗粒内的孔扩散;pH在3～4时,颗粒羟基氧化锆的氟吸附量达到最大值27.72 mg/g,其他范围内pH的升高或降低都会导致氟吸附量的降低;Cl-对颗粒羟基氧化锆除氟过程无明显影响,而SO24-和PO34-对颗粒羟基氧化锆除氟过程影响较大,且浓度越高影响越大;扫描电镜和X射线能谱测试结果显示颗粒内随着颗粒深度的增加,F-含量逐渐降低,F-在颗粒内部的传质过程受到阻碍,SO24-和PO34-对颗粒羟基氧化锆除氟的干扰作用主要发生在颗粒表面。