A comparison of on-site nutrient and energy recycling technologies in algal oil production

Research on biofuel production pathways from algae continues because among other potential advantages they avoid key consequential effects of terrestrial oil crops, such as competition for cropland. However, the economics, energetic balance, and climate change emissions from algal biofuels pathways do not always show great potential, due in part to high fertilizer demand. Nutrient recycling from algal biomass residue is likely to be essential for reducing the environmental impacts and cost associated with algae-derived fuels. After a review of available technologies, anaerobic digestion (AD) and hydrothermal liquefaction (HTL) were selected and compared on their nutrient recycling and energy recovery potential for lipid-extracted algal biomass using the microalgae strain Scenedesmus dimorphus. For 1 kg (dry weight) of algae cultivated in an open raceway pond, 40.7 g N and 3.8 g P can be recycled through AD, while 26.0 g N and 6.8 g P can be recycled through HTL. In terms of energy production, 2.49 MJ heat and 2.61 MJ electricity are generated from AD biogas combustion to meet production system demands, while 3.30 MJ heat and 0.95 MJ electricity from HTL products are generated and used within the production system.Assuming recycled nutrient products from AD or HTL technologies displace demand for synthetic fertilizers, and energy products displace natural gas and electricity, the life cycle greenhouse gas reduction achieved by adding AD to the simulated algal oil production system is between 622 and 808 g carbon dioxide equivalent (CO₂e)/kg biomass depending on substitution assumptions, while the life cycle GHG reduction achieved by HTL is between 513 and 535 g CO₂e/kg biomass depending on substitution assumptions. Based on the effectiveness of nutrient recycling and energy recovery, as well as technology maturity, AD appears to perform better than HTL as a nutrient and energy recycling technology in algae oil production systems.     

Greenhouse gas emissions and energy balance of sunflower biodiesel: Identification of its key factors in the supply chain

The production of first generation biofuels, such as sunflower-based biodiesel, is potentially an option for diversifying the energy matrix in several South American countries. However, biofuels present environmental challenges, especially concerning the reduction of greenhouse gas (GHG) emissions. This study, using a life-cycle approach, evaluates the GHG emissions and energy balance of the future nationwide production of sunflower-based biodiesel in Chile. Direct land use change is included in the analysis. The overall findings indicate that sunflower biodiesel, under the most likely production conditions, will have better environmental performance than fossil diesel in terms of both indicators. The agricultural stage is associated to key factors such as land use change, and nitrogen fertilizers. These factors contribute significantly to GHG emissions or energy demand in the biodiesel life cycle. The sensitivity analysis shows that no GHG emission saving could occur if nitrogen fertilizers rate exceeds 330 kg N/ha. In order to reduce the environmental impacts of this biofuel, improvement measures are suggested.     

Large-scale utilization of biomass energy and carbon dioxide capture and storage in the transport and electricity sectors under stringent CO2 concentration limit scenarios

Large-scale, dedicated commercial biomass energy systems are a potentially large contributor to meeting global climate policy targets by the end of the century. We use an integrated assessment model of energy and agriculture systems to show that, given a climate policy in which terrestrial carbon is appropriately valued equally with carbon emitted from the energy system, biomass energy has the potential to be a major component of achieving these low concentration targets. A key aspect of the research presented here is that the costs of processing and transporting biomass energy at much larger scales than current experience are explicitly incorporated into the modeling. From the scenario results, 120–160 EJ/year of biomass energy is produced globally by midcentury and 200–250 EJ/year by the end of this century. In the first half of the century, much of this biomass is from agricultural and forest residues, but after 2050 dedicated cellulosic biomass crops become the majority source, along with growing utilization of waste-to-energy. The ability to draw on a diverse set of biomass-based feedstocks helps to reduce the pressure for drastic large-scale changes in land use and the attendant environmental, ecological, and economic consequences those changes would unleash. In terms of the conversion of bioenergy feedstocks into value added energy, this paper demonstrates that biomass is and will continue to be used to generate electricity as well as liquid transportation fuels. A particular focus of this paper is to show how climate policies and technology assumptions – especially the availability of carbon dioxide capture and storage (CCS) technologies – affect the decisions made about where the biomass is used in the energy system. The potential for net-negative electric sector emissions through the use of CCS with biomass feedstocks provides an attractive part of the solution for meeting stringent emissions constraints; we find that at carbon prices above $150/tCO₂, over 90% of biomass in the energy system is used in combination with CCS. Despite the higher technology costs of CCS, it is a very important tool in controlling the cost of meeting a target, offsetting the venting of CO₂ from sectors of the energy system that may be more expensive to mitigate, such as oil use in transportation. CCS is also used heavily with other fuels such as coal and natural gas, and by 2095 a total of 1530 GtCO₂ has been stored in deep geologic reservoirs. The paper also discusses the role of cellulosic ethanol and Fischer–Tropsch biomass derived transportation fuels as two representative conversion processes and shows that both technologies may be important contributors to liquid fuels production, with unique costs and emissions characteristics.     

Impacts of urban forests on offsetting carbon emissions from industrial energy use in Hangzhou,China

This study quantified carbon storage and sequestration by urban forests and carbon emissions from energy consumption by several industrial sources in Hangzhou, China. Carbon (C) storage and sequestration were quantified using urban forest inventory data and by applying volume-derived biomass equations and other models relating net primary productivity (NPP) and mean annual biomass increments. Industrial energy use C emissions were estimated by accounting for fossil fuel use and assigning C emission factors. Total C storage by Hangzhou's urban forests was estimated at 11.74 Tg C, and C storage per hectare was 30.25 t C. Carbon sequestration by urban forests was 1,328, 166.55 t C/year, and C sequestration per ha was 1.66 t C/ha/year. Carbon emissions from industrial energy use in Hangzhou were 7 Tg C/year. Urban forests, through sequestration, annually offset 18.57% of the amount of carbon emitted by industrial enterprises, and store an amount of C equivalent to 1.75 times the amount of annual C emitted by industrial energy uses within the city. Management practices for improving Hangzhou's urban forests function of offsetting C emissions from energy consumption are explored. These results can be used to evaluate the urban forests' role in reducing atmospheric carbon dioxide.     

The value of post-combustion carbon dioxide capture and storage technologies in a world with uncertain greenhouse gas emissions constraints

By analyzing how the largest CO₂ emitting electricity-generating region in the United States, the East Central Area Reliability Coordination Agreement (ECAR), responds to hypothetical constraints on greenhouse gas emissions, the authors demonstrate that there is an enduring role for post-combustion CO₂ capture technologies. The utilization of pulverized coal generation with carbon dioxide capture and storage (PC + CCS) technologies is particularly significant in a world where there is uncertainty about the future evolution of climate policy and in particular uncertainty about the rate at which the climate policy will become more stringent. The paper's analysis shows that within this one large, heavily coal-dominated electricity-generating region, as much as 20–40 GW of PC + CCS could be operating before the middle of this century. Depending upon the state of PC + CCS technology development and the evolution of future climate policy, the analysis shows that these CCS systems could be mated to either pre-existing PC units or PC units that are currently under construction, announced and planned units, as well as PC units that could continue to be built for a number of decades even in the face of a climate policy. In nearly all the cases analyzed here, these PC + CCS generation units are in addition to a much larger deployment of CCS-enabled coal-fueled integrated gasification combined cycle (IGCC) power plants. The analysis presented here shows that the combined deployment of PC + CCS and IGCC + CCS units within this one region of the U.S. could result in the potential capture and storage of between 3.2 and 4.9 Gt of CO₂ before the middle of this century in the region's deep geologic storage formations.     

Storage and characterization of cotton gin waste for ethanol production

In 2002, about 17.1 million bales of cotton were ginned in the United States and the estimated cotton gin waste was 2.25 × 10⁹ kg. The disposal of cotton gin waste (CGW) is a significant problem in the cotton ginning industry, but CGW could be potentially used as feedstock for bioethanol. Freshly discharged CGW and stored CGW were characterized for storage stability and potential for ethanol production by determining their summative compositions. The bulk densities of the fresh wet and dry CGW were 210.2 ± 59.9 kg m⁻³ and 183.3 ± 52.2 kg m⁻³, respectively. After six months of storage the volume of piles A, B, and C decreased by 38.7%, 41.5%, and 33.3%, respectively, relative to the volume of the pile at the start of the storage. The ash content of the CGW was very high ranging from 10% to 21% and the acid-insoluble fraction was high (21–24%). The total carbohydrate content was very low and ranged from 34% to 49%. After three months storage, chemical compositional analysis showed the loss of total carbohydrates was minimal but after six months, the losses were as high as 25%. This loss of carbohydrates suggests that under open storage conditions, the feedstock must be processed within three months to reduce ethanol yield losses.     

Approaches for analyzing local carbon mitigation strategies: Tompkins County,New York,USA

A carbon budget was calculated for Tompkins County, NY, a semi-rural upstate county with a population density of 78 pp/km². The costs and potential for several carbon mitigation options were analyzed in four categories: terrestrial C sequestration, local power generation, transportation, and energy end-use efficiency. This study outlines a methodology for conducting this type of local-scale analysis, including sources and calculations adaptable to different localities. Effective carbon mitigation strategies for this county based on costs/Mg C and maximum potential include reforestation of abandoned agricultural lands, biomass production for residential heating and co-firing in coal power plants, changes in personal behavior related to transportation (e.g., public transportation), installation of residential energy efficient products such as programmable thermostats or compact fluorescent light bulbs, and development of local wind power. The total county emissions are about 340 Gg C/year, with biomass sequestration rates of 121 Gg C/year. The potential for mitigation, assuming full market penetration, amounts to about 234 Gg C/year (69%), with 100 Gg C/year (29%) at no net cost to the consumer. The development of local-scale C mitigation plans based on this sort of model of analysis is feasible and would be useful for guiding investments in climate change prevention.     

Energy and carbon dioxide intensity of Thailand's steel industry and greenhouse gas emission projection toward the year 2050

The purpose of this article is to study the energy and carbon dioxide intensities of Thailand's steel industry and to propose greenhouse gas emission trends from the year 2011 to 2050 under plausible scenarios. The amount of CO₂ emission from iron and steel production was calculated using the 2006 Intergovernmental Panel on Climate Change (IPCC) guidelines in the boundary of production process (gate to gate). The results showed that energy intensity of semi-finished steel product was 2.84 GJ/t semi-finished steel and CO₂ intensity was 0.37 tCO_2eq/t semi-finished steel. Energy intensity of steel finishing process was 1.86 GJ/t finished steel and CO₂ intensity was 0.16 tCO_2eq/t finished steel. Using three plausible scenarios from Thailand's steel industry, S1: without integrated steel plant (baseline scenario), S2: with a traditional integrated BF–BOF route and S3: with an alternative integrated DR-EAF route; the Greenhouse Gas emissions from the year 2011 to 2050 were projected. In 2050, the CO₂ emission from S1 (baseline scenario) was 4.84 million tonnes, S2 was 21.96 million tonnes increasing 4.54 times from baseline scenario. The CO₂ emission from S3 was 7.12 million tonnes increasing 1.47 times from baseline scenario.     

Modeling the impacts of climate policy on the deployment of carbon dioxide capture and geologic storage across electric power regions in the United States

This paper summarizes the results of a first-of-its-kind holistic, integrated economic analysis of the potential role of carbon dioxide (CO₂) capture and storage (CCS) technologies across the regional segments of the United States (U.S.) electric power sector, over the time frame 2005–2045, in response to two hypothetical emissions control policies analyzed against two potential energy supply futures that include updated and substantially higher projected prices for natural gas. This paper's detailed analysis is made possible by combining two specialized models developed at Battelle: the Battelle CO₂-GIS to determine the regional capacity and cost of CO₂ transport and geologic storage; and the Battelle Carbon Management Electricity Model, an electric system optimal capacity expansion and dispatch model, to examine the investment and operation of electric power technologies with CCS against the background of other options. A key feature of this paper's analysis is an attempt to explicitly model the inherent heterogeneities that exist in both the nation's current and future electricity generation infrastructure and in its candidate deep geologic CO₂ storage formations. Overall, between 180 and 580 gigawatts (GW) of coal-fired integrated gasification combined cycle with CCS (IGCC + CCS) capacity is built by 2045 in these four scenarios, requiring between 12 and 41 gigatonnes of CO₂ (GtCO₂) storage in regional deep geologic reservoirs across the U.S. Nearly all of this CO₂ is from new IGCC + CCS systems, which start to deploy after 2025. Relatively little IGCC + CCS capacity is built before that time, primarily under unique niche opportunities. For the most part, CO₂ emissions prices will likely need to be sustained at over $20/tonne CO₂ before CCS begins to deploy on a large scale within the electric power sector. Within these broad national trends, a highly nuanced picture of CCS deployment across the U.S. emerges. Across the four scenarios studied here, power plant builders and operators within some North American Electric Reliability Council (NERC) regions do not employ any CCS while other regions build more than 100 GW of CCS-enabled generation capacity. One region sees as much as 50% of its geologic CO₂ storage reservoirs’ total theoretical capacity consumed by 2045, while most of the regions still have more than 90% of their potential storage capacity available to meet storage needs in the second half of the century and beyond. A detailed presentation of the results for power plant builds and operation in two key regions: ECAR in the Midwest and ERCOT in Texas, provides further insight into the diverse set of economic decisions that generate the national and aggregate regional results.     

Global anthropogenic selenium cycles for 1940–2010

Selenium plays an important role in emerging thin film solar energy technologies. As solar energy is expected to have a larger share in the world's future energy portfolio, the long-term availability of selenium becomes a potential concern, yet no global cycles have ever been generated. In this work, the global cycles, stocks, and flows of selenium are characterized for the entire time period 1940–2010 by using principles of material flow analysis (MFA). The cycles present information on the production, fabrication and manufacturing, use, and resource management stages during that period. The results of the analysis show that during 1940–2010 approximately 90 Gg of refined selenium was produced and entered into fabrication and manufacturing worldwide. 60 Gg of this amount (two-thirds!) was dissipated into the environment through end-uses such as chemicals, pigments, glass manufacturing, metallurgical additives, and fertilizer and feed additives. The in-use stock of selenium is estimated at 2.7 Gg as of 2010. Because of data limitations such as proprietary and withheld information, these figures represent informed estimates rather than exact values. Selenium can be recovered from end-of-life electrical and electronic equipment, while for other end-uses recycling is difficult or impossible. One of the ways to buttress supplies of selenium for future technologies would be to deploy recycling schemes for photovoltaics as well as other electronics applications.     

Energy balances,greenhouse gas emissions and economics of biochar production from palm oil empty fruit bunches

This paper presents results from a gate-to-gate analysis of the energy balance, greenhouse gas (GHG) emissions and economic efficiency of biochar production from palm oil empty fruit bunches (EFB). The analysis is based on data obtained from EFB combustion in a slow pyrolysis plant in Selangor, Malaysia. The outputs of the slow pyrolysis plant are biochar, syngas, bio-oil and water vapor. The net energy yield of the biochar produced in the Selangor plant is 11.47 MJ kg⁻¹ EFB. The energy content of the biochar produced is higher than the energy required for producing the biochar, i.e. the energy balance of biochar production is positive. The combustion of EFB using diesel fuel has the largest energy demand of 2.31 MJ kg⁻¹ EFB in the pyrolysis process. Comparatively smaller amounts of energy are required as electricity (0.39 MJ kg⁻¹ EFB) and for transportation of biochar to the warehouse and the field (0.13 MJ kg⁻¹ EFB). The net greenhouse gas emissions of the studied biochar production account for 0.046 kg CO₂-equiv. kg⁻¹ EFB yr⁻¹ without considering fertilizer substitution effects and carbon accumulation from biochar in the soil. The studied biochar production is profitable where biochar can be sold for at least 533 US-$ t⁻¹. Potential measures for improvement are discussed, including higher productivity of biochar production, reduced energy consumption and efficient use of the byproducts from the slow pyrolysis.     

Techno-economic evaluation of biogas upgrading process using CO2 facilitated transport membrane

The biogas upgrading by membrane separation process using a highly efficient CO₂-selective polyvinylamine/polyvinylalcohol (PVAm/PVA) blend membrane was investigated by experimental study and simulation with respect to process design, operation optimization and economic evaluation. This blend membrane takes advantages of the unique CO₂ facilitated transport from PVAm and the robust mechanical properties from PVA, exhibits both high CO₂/CH₄ separation efficiency and very good stability. CO₂ transports through the water swollen membrane matrix in the form of bicarbonate. CO₂/CH₄ selectivity up to 40 and CO₂ permeance up to 0.55 m³(STP)/m² h bar at 2 bar were documented in lab with synthesized biogas (35% CO₂ and 65% CH₄). Membrane performances at varying feed pressures were recorded and used as the simulation basis in this work. The process simulation of an on-farm scale biogas upgrading plant (1000 Nm³/h) was conducted. Processes with four different membrane module configurations with or without recycle were evaluated technically and economically, and the 2-stage in cascade with recycle configuration was proven optimal among the four processes. The sensitivity of the process to various operation parameters was analyzed and the operation conditions were optimized.     

Carbon dioxide capture with concentrated,aqueous piperazine

Concentrated, aqueous piperazine (PZ) has been investigated as a novel amine solvent for carbon dioxide (CO₂) absorption. The CO₂ absorption rate of aqueous PZ is more than double that of 7 m MEA and the amine volatility at 40 °C ranges from 11 to 21 ppm. Thermal degradation is negligible in concentrated, aqueous PZ up to a temperature of 150 °C, a significant advantage over MEA systems. Oxidation of concentrated, aqueous PZ is appreciable in the presence of copper (4 mM), but negligible in the presence of chromium (0.6 mM), nickel (0.25 mM), iron (0.25 mM), and vanadium (0.1 mM). Initial system modeling suggests that 8 m PZ will use 10–20% less energy than 7 m MEA. The fast mass transfer and low degradation rates suggest that concentrated, aqueous PZ has the potential to be a preferred solvent for CO₂ capture.     

The use of recycled metal in dentistry: Evaluation of mechanical properties of titanium waste recasting

Environmental concerns are increasing rapidly, and the public and industry are concerned about natural resources. The products are produced to meet the customer's demand as to quality. However, today it is equally important to take into account cost, ecological factors in production and recycling of products. The same way, the dentistry must contribution with a recasting the alloys used to rehabilitation oral.This study evaluated the effect of the condition of Ti (as-received and re-cast) on its mechanical properties, microstructure and fractography. Castings (n = 6) with Ti in the as-received and once recast condition were made in a centrifugal casting machine using a high-purity argon gas. The ultimate tensile strength (UTS), proportional limit (PL) and elongation (EL) of the as-received specimens were evaluated in a universal testing machine at a crosshead speed of 1 mm/min. The fractured specimens were polished down for Vicker's microhardness (VHN) measurement (100 g/15 s) from 25 μm below the cast surface, then at depths of 50, 100, 200 and 500 μm. The microstructures of the alloys were also revealed. Scanning electron microscopy fractography was undertaken for the fractured surfaces after testing. The data from the mechanical tests and hardness were subjected to the Student's t-test and two-way repeated measures ANOVA, respectively. Tukey's test was used for pairwise comparison (α = 0.05). Higher UTS, PL and VHN and lower EL were observed for recast cp Ti. The microstructure was not influenced by recasting, but the mode of fracture was.The use of the recasting procedure can lower the costs of cp Ti castings and can be safely in dentistry.     

Design and implementation study of a Permanent Selective Collection Program (PSCP) on a University campus in Brazil

The selective collection and recycling of municipal solid waste are presented as stages of an integrated program of solid waste management to minimize the environmental impact of the treatment and final disposal of solid waste. Therefore, this program aims to save natural resources, such as energy and raw materials, in the manufacture of new products and to conserve areas for sites, such as to minimize the use of existing landfill sites, and to minimize the need for new waste treatment sites. A university is composed of educational professionals aware of their societal responsibilities, and, therefore, they play a fundamental role in the management of the university's solid waste. This study presents the design and implementation of a Permanent Selective Collection Program (PSCP) at the Federal University of Itajubá (Universidade Federal de Itajubá, UNIFEI), Itajubá-MG, Brazil. The material requirements for initiating the PSCP have been identified, and an action plan for continuous program improvement, which is initially based on the collection of performance indicator data for the PSCP campus, has been developed. Finally, the data from the PSCP performance indicators and software from the United States Environmental Protection Agency, the Landfill Gas Generation Model (LandGEM) and the Waste Reduction Model (WARM), were used to evaluate the impact of implementing PSCP in terms of energy and the generation of greenhouse gases (GHG). The results were promising, showing that there has been an improvement, since the inception of PSCP in 2006, in separating materials for selective collection, even though paper (41.00 wt%), plastic (6.00 wt%) and organic matter (26.00 wt%) are still highly generated wastes. The WARM simulations for a scenario in which 90% of the waste is sent for recycling resulted in an economy of −7 tCO₂ or −74.91 GJ (on an energy basis). The LandGEM (USEPA) simulations estimated 1424.60 kWh of energy in the peak production year.     

CO2 capture from power plants: Part I. A parametric study of the technical performance based on monoethanolamine

Capture and storage of CO₂ from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO₂ capture process from flue gas of a 600 MWe bituminous coal fired power plant, based on absorption/desorption process with MEA solutions, using ASPEN Plus with the RADFRAC subroutine, was performed. This optimization aimed to reduce the energy requirement for solvent regeneration, by investigating the effects of CO₂ removal percentage, MEA concentration, lean solvent loading, stripper operating pressure and lean solvent temperature.Major energy savings can be realized by optimizing the lean solvent loading, the amine solvent concentration as well as the stripper operating pressure. A minimum thermal energy requirement was found at a lean MEA loading of 0.3, using a 40 wt.% MEA solution and a stripper operating pressure of 210 kPa, resulting in a thermal energy requirement of 3.0 GJ/ton CO₂, which is 23% lower than the base case of 3.9 GJ/ton CO₂. Although the solvent process conditions might not be realisable for MEA due to constraints imposed by corrosion and solvent degradation, the results show that a parametric study will point towards possibilities for process optimisation.     

Facilitating access to the algal economy: Mapping waste resources to identify suitable locations for algal farms in Queensland

Algae offer a multiple-benefit opportunity as the products that can result from algal cultivation are numerous and diverse. However, commercial production of algal-derived materials is scarce and in Queensland Australia is virtually non-existent, partly due to challenges around readily available resources. In this work, the potential to regionally recycle waste nitrogen (N), phosphorus (P) and CO₂ to support algal production is considered. A feature of the work is mapping the availability of the three resources for algal cultivation (N, P and CO₂) together with climatic and land use considerations. Mapping resolution is defined by the boundaries of Queensland's (Australia) regional authorities. Layering the maps enables identification of regional hotspots for growing algae. Waste resources are shown to be most abundant in Mackay, Burdekin, Toowoomba, Cassowary and Bundaberg; regions which also have favourable eco-climatic conditions. Waste nitrogen is the limiting waste stream, in these and most other regions however additional requirements can be fixed atmospherically, whereas waste CO₂ is shown to be abundant relative to waste nutrients. It is found that, based on the availability of waste phosphorus, the top 5 most suitable regions have sufficient resources to produce around 1.1 million t/y of algal biomass. This could potentially produce 309 ML of biodiesel which is 5% of Queensland's 2011 diesel oil sales. The outcomes of this work highlight new opportunities for industrial ecology in non-urban regions.     

Linking energy scenarios with metal demand modeling–The case of indium in CIGS solar cells

Some renewable energy technologies rely on the functionalities provided by geochemically scarce metals. One example are CIGS solar cells, an emerging thin film photovoltaic technology, which contain indium. In this study we model global future indium demand related to the implementation of various energy scenarios and assess implications for the supply system. Influencing parameters of the demand model are either static or dynamic and include technology shares, technological progress and handling in the anthroposphere. Parameters’ levels reflect pessimistic, reference, and optimistic development. The demand from other indium containing products is roughly estimated. For the reference case, the installed capacity of CIGS solar cells ranges from 12 to 387 GW in 2030 (31–1401 GW in 2050), depending on the energy scenario chosen. This translates to between 485 and 15,724 tonnes of primary indium needed from 2000 to 2030 (789–30,556 tonnes through 2050). One scenario exemplifies that optimistic assumptions for technological progress and handling in the anthroposphere can reduce cumulative primary indium demand by 43% until 2050 compared to the reference case, while with pessimistic assumptions the demand increases by about a factor of five. To meet the future indium demand, several options to increase supply are discussed: (1) expansion of zinc metal provision (indium is currently a by-product of zinc mining), (2) improving extraction efficiency, (3) new mining activities where indium is a by-product of other metals and (4) mining of historic residues. Potential future constraints and environmental impacts of these supply options are also briefly discussed.     

Pathways towards large-scale implementation of CO2 capture and storage: A case study for the Netherlands

We sketch four possible pathways how carbon dioxide capture and storage (CCS) (r)evolution may occur in the Netherlands, after which the implications in terms of CO₂ stored and avoided, costs and infrastructural requirements are quantified. CCS may play a significant role in decarbonising the Dutch energy and industrial sector, which currently emits nearly 100 Mt CO₂/year. We found that 15 Mt CO₂ could be avoided annually by 2020, provided some of the larger gas fields that become available the coming decade could be used for CO₂ storage. Halfway this century, the mitigation potential of CCS in the power sector, industry and transport fuel production is estimated at maximally 80–110 Mt CO₂/year, of which 60–80 Mt CO₂/year may be avoided at costs between 15 and 40 €/t CO₂, including transport and storage. Avoiding 30–60 Mt CO₂/year by means of CCS is considered realistic given the storage potential represented by Dutch gas fields, although it requires planning to assure that domestic storage capacity could be used for CO₂ storage. In an aggressive climate policy, avoiding another 50 Mt CO₂/year may be possible provided that nearly all capture opportunities that occur are taken. Storing such large amounts of CO₂ would only be possible if the Groningen gas field or large reservoirs in the British or Norwegian part of the North Sea will become available.     

Ionic liquids for post-combustion CO2 absorption

The present work is a study to evaluate ionic liquids as a potential solvent for post-combustion CO₂ capture. In order to enhance the absorption performance of a CO₂ capture unit, different ionic liquids have been designed and tested. The main goal was to get a comparison between a reference liquid and selected ionic liquids. As the reference, a solution of 30 w% monoethanolamine (MEA) and water was used. A large range of different pure and diluted ionic liquids was tested with a special screening process to gain general information about the CO₂ absorption performance. Based on these results, a 60 w% ionic liquid solution in water was selected and the vapour–liquid equilibrium was measured experimentally between 40 °C and 110 °C. From these curves the enthalpy of absorption for capturing CO₂ into the ionic liquid was determined. With these important parameters one is able to calculate the total energy demand for stripping of CO₂ from the loaded solvent for comparison of the ionic liquid based solvent with the reference MEA solvent. The energy demand of this 60 w% ionic liquid is slightly lower than that of the reference solution, resulting in possible energy savings between 12 and 16%.