A comprehensive waste collection cost model applied to post-consumer plastic packaging waste

Post-consumer plastic packaging waste (PPW) can be collected for recycling via source separation or post-separation. In source separation, households separate plastics from other waste before collection, whereas in post-separation waste is separated at a treatment centre after collection. There are also two collection schemes, either curb side or via drop-off locations. These different schemes have impact on total costs of collection at the municipal level. It can also influence the facility choices and network design. Therefore, a method which can compare costs of various collection schemes is needed.A comprehensive cost model was developed to compare costs of municipal collection schemes of PPW. The ‘municipal waste collection cost model’ is based on variables including fixed and variable costs per vehicle, personnel cost, container or bag costs as well as on emission costs (using imaginary carbon taxes). The model can be used for decision support when strategic changes to the collection scheme of municipalities are considered. The model takes into account the characteristics of municipalities, including urbanization degree and taxation schemes for household waste management.The model was applied to the Dutch case of post-consumer plastic packaging waste. Results showed that that in general post-separation collection has the lowest costs and curb side collection in urban municipalities without residual waste collection taxing schemes the highest. These results were supported by the conducted sensitivity analysis, which showed that higher source separation responses are negatively related to curb side collection costs. Greenhouse gas emission costs are a significant part of the total costs when collecting post-consumer plastic packaging waste due to the low density to weight ratio of the materials collect. These costs can amount to 15% of the total collection costs.     

Identifying the key factors in increasing recycling and reducing residual household waste: a case study of the Flemish region of Belgium

The competent waste authority in the Flemish region of Belgium created the 'Implementation plan household waste 2003-2007' and the 'Implementation plan sustainable management 2010-2015' to comply with EU regulation. It incorporates European and regional requirements and describes strategies, goals, actions and instruments for the collection and treatment of household waste. The central mandatory goal is to reduce and maintain the amount of residual household waste to 150 kg per capita per year between 2010-2015. In literature, a reasonable body of information has been published on the effectiveness and efficiency of a variety of policy instruments, but the information is complex, often contradictory and difficult to interpret. The objective of this paper is to identify, through the development of a binary logistic regression model, those variables of the waste collection scheme that help municipalities to reach the mandatory 150 kg goal. The model covers a number of variables for household characteristics, provision of recycling services, frequency of waste collection and charging for waste services. This paper, however, is not about waste prevention and reuse. The dataset originates from 2003. Four out of 12 variables in the model contributed significantly: income per capita, cost of residual waste collection, collection frequency and separate curbside collection of organic waste.     

A mixed integer linear programming model for optimisation of organics management in an integrated solid waste system

In this paper, the authors propose a mixed integer linear programming model for designing an Integrated Solid Waste Management System (ISWMS) to meet specific economic goals. The model refers to a set of municipalities, known as ‘local basin’, which have to share a common waste management system. At the municipal level the model allows for an identification of the optimal collection service option; at the local basin level, the model provides the optimal waste flow appropriate to the collection service option of each municipality. The model has been applied to a full-scale case study of an area located in southeast Italy. A scenario analysis was carried out to investigate alternative municipal solid waste management options, which fundamentally differ in the organic flow mass rate to be either collected and composted or landfilled. Findings show that an increase in the cost of landfilling determines the optimal collection scenario and the configuration plants tend to recover higher rates of organics in separate collection and thus higher refuse derived fuel productions. The results obtained validate the application of the model in both the strategic planning and operational phases, by supporting public administrators at both municipality and local basin level in decision making and evaluation of technical and economic performances of ISWMSs.     

Assessing and improving management practices when planning packaging waste collection systems

Packaging waste collection systems are responsible to collect, within a geographic area, three types of packaging materials (paper, glass and plastic/metal) that are disposed by the final consumer into special bins. Those systems are often characterized by having a network with multiple depots that act as transfer and sorting stations, and where the vehicle fleet is based. However, each depot is often managed independently and not as a part of a unique system. In this work, four current tactical/operational practices that contribute to the independent management of each depot are analysed. The change of such practices is investigated and their impact assessed on the total collection cost. A solution methodology based on mathematical formulations is developed to plan service areas, vehicle routes and vehicle schedules taking into account new alternative solutions in managing the system as a whole. Such methodology is applied to a real case study of a company responsible for the collection of the packaging waste in 7 municipalities in mainland Portugal. New service areas, collection routes and vehicle schedules are defined and significant savings are obtained in terms of the total distance travelled as well as in terms of the number of required vehicles, resulting in a decreasing of the total system cost.     

Assessment of public vs private MSW management: a case study

Public-private partnerships in urban environmental services have witnessed increased interest in recent years primarily to reform the weak performance of the public sector, reduce cost, improve efficiency, and ensure environmental protection. In this context, successful public-private partnerships require a thorough analysis of opportunities, a deliberate attention to process details, and a continuous examination of services to determine whether they are more effectively performed by the private sector. A comparative assessment of municipal solid waste collection services in the two largest cities in Lebanon where until recently municipal solid waste collection is private in one and public in the other is conducted. While quality of municipal solid waste collection improved, due to private sector participation, the corresponding cost did not, due to monopoly and an inadequate organizational plan defining a proper division of responsibilities between the private and the public sector.     

A bioeconomic model of afforestation in Southern Ontario: Integration of fiber,carbon and municipal biosolids values

This study explores the economic attractiveness of afforestation as a strategy for the joint production of fibre, carbon storage and biosolids (treated municipal sewage sludge) disposal for municipalities in Southern and Central Ontario, Canada. We use a spatial, stochastic model, the Canadian Forest Service Afforestation Feasibility Model (CFS-AFM), to simulate a range of spatial biosolids application scenarios in hybrid poplar afforestation projects. Results suggest that such joint afforestation strategies could be financially attractive. Significant cost savings can be expected through decreases in transportation distances and avoided waste disposal fees. Sensitivity analysis is used to examine the effects of variations in critical model parameters on net present values. Our findings indicate that waste disposal savings from application of biosolids on hybrid poplar plantations combined with incentives for landowners to sequester carbon can easily compete with agricultural land rental values in some regions of Ontario. Social acceptance of this kind of activity, however, may be an impediment to adoption.     

The costs and benefits of packaging waste management systems in Europe: the perspective of local authorities

Local authorities are generally in charge of household packaging waste management operations, particularly in countries with Green Dot schemes or similar extended producer responsibility systems. This leads to the need of establishing a system of financial transfers between the packaging industry and the local authorities (regarding the costs involved in selective collection and sorting). In the present study, the costs and benefits of recycling, from the perspective of local authorities, are compared for Portugal, Belgium and Italy (in Lombardia region), adopting the same economic–financial methodology. The results show that the industry is not paying the net cost of packaging waste management. If the savings attained by diverting packaging waste from other treatment operations are not considered, it seems that the industry should increase the financial support to local authorities. However, if the avoided costs with other treatments are considered as a benefit for local authorities, the costs are generally outweighed by the benefits, and the financial support could, therefore, be reduced.     

Introduction of a waste incineration tax: Effects on the Swedish waste flows

A tax on waste-to-energy incineration of fossil carbon in municipal solid waste from households was introduced in Sweden on July 1, 2006. The tax has led to higher incineration gate fees. One of the main purposes with the tax is to increase the incentive for recycling of materials, including biological treatment. We investigate whether and to what extent this effect can be expected. A spreadsheet model is developed in order to estimate the net marginal cost of alternative waste treatment methods, i.e., the marginal cost of alternative treatment minus avoided cost of incineration. The value of the households’ time needed for source separation is discussed and included. The model includes the nine largest fractions, totalling 85% (weight), of the household waste currently being sent to waste incineration: food waste, newsprint, paper packaging, soft and hard plastic packaging, diapers, yard waste, other paper waste, and non-combustible waste. Our results indicate that the incineration tax will have the largest effect on biological treatment of kitchen and garden waste, which may increase by 9%. The consequences of an incineration tax depend on: (a) the level of the tax, (b) whether the tax is based on an assumed average Swedish fossil carbon content or on the measured carbon content in each incineration plant, (c) institutional factors such as the cooperation between waste incinerators, and (d) technological factors such as the availability of central sorting of waste or techniques for measurement of fossil carbon in exhaust gases, etc. Information turns out to be a key factor in transferring the governing force of the tax to the households as well improving the households’ attitudes towards material recycling.     

Introduction of a waste incineration tax: Effects on the Swedish waste flows

A tax on waste-to-energy incineration of fossil carbon in municipal solid waste from households was introduced in Sweden on July 1, 2006. The tax has led to higher incineration gate fees. One of the main purposes with the tax is to increase the incentive for recycling of materials, including biological treatment. We investigate whether and to what extent this effect can be expected. A spreadsheet model is developed in order to estimate the net marginal cost of alternative waste treatment methods, i.e., the marginal cost of alternative treatment minus avoided cost of incineration. The value of the households’ time needed for source separation is discussed and included. The model includes the nine largest fractions, totalling 85% (weight), of the household waste currently being sent to waste incineration: food waste, newsprint, paper packaging, soft and hard plastic packaging, diapers, yard waste, other paper waste, and non-combustible waste. Our results indicate that the incineration tax will have the largest effect on biological treatment of kitchen and garden waste, which may increase by 9%. The consequences of an incineration tax depend on: (a) the level of the tax, (b) whether the tax is based on an assumed average Swedish fossil carbon content or on the measured carbon content in each incineration plant, (c) institutional factors such as the cooperation between waste incinerators, and (d) technological factors such as the availability of central sorting of waste or techniques for measurement of fossil carbon in exhaust gases, etc. Information turns out to be a key factor in transferring the governing force of the tax to the households as well improving the households’ attitudes towards material recycling.     

Solid Waste Management Practices in the Eastern Province of Saudi Arabia

Solid waste management practices in the Eastern Province of Saudi Arabia are reviewed. The officials of various municipalities and agencies responsible for collecting and disposing of municipal waste were interviewed. The refuse generation rate found is in the range of 1.61–2.72 kg per capita per day. The refuse composition data indicate a high percentage of glass, metals, and wood. For storage purposes, 0.2-m³ barrels are used in residential areas and 0.75 to 1.50 m³-capacity containers are used in commerical areas. The present solid-waste collection system is labor-intensive, and a significant part of the budget is spent on collection and haul operations. The unit collection and haul cost is much higher than the unit disposal cost of refuse. The direct haul of refuse is the common practice, and the use of transfer stations has not yet been considered. It is also observed that the disposal methods used at these sites are not in line with modern techniques for refuse disposal. Landfilling and combined burning and landfilling are the common disposal methods at all the sites.     

The influence of collection facility attributes on household collection rates of electronic waste: The case of televisions and computer monitors

In the US, household electronic waste collected for recycling is primarily by voluntary drop-off at designated collection facilities. This study examines the influence of specific collection facility attributes (recycling fees charged, number of days open, and driving distance) on the household collection rate of e-waste in the US state of Maine. Data were collected for household computer monitor and television collection for 92 municipal waste transfer facilities representing 30% of the state's population for one year. Results suggest that recycling fees are negatively correlated with the number of televisions and computer monitors collected; furthermore, the more frequently facilities were open, the more televisions and computer monitors were collected per capita. The distance from the facility had no correlation, which prompted an analysis of whether the existence of a curbside collection system in the municipality was influential. Results show a negative correlation between computer monitor and television collection and a municipality having recycling (but not e-waste) curbside collection. Based on the results of this study, policymakers may be able to increase the collection rate of household e-waste by eliminating or lowering recycling fees, expanding collection days and hours to increase convenience, and/or considering curbside collection of e-waste.     

Investigating household preferences for kerbside recycling services in London: a choice experiment approach

Recent developments in national and European Union waste management policy have prompted considerable interest in alternative waste management programs, such as recycling, which could divert a portion of the municipal solid waste stream from landfills. This paper examines household preferences for kerbside recycling services and uses a stated preference choice experiment method to estimate households' valuation of such services. Using a sample of 188 households in the London area, the empirical analysis yields estimates of the willingness to pay for the number of 'dry' materials collected, the collection of compost, textile collection and the frequency of collection.     

城市生活垃圾收集与运输路线的优化

城市生活垃圾收运系统是生活垃圾管理的重要组成部分,收运费用占垃圾处理处置费用的40%～50%,为降低收运系统成本,减少环境污染与社会影响,需对垃圾车的收运路线进行合理优化。本文在参考国内外大量文献的基础上,评述了国内外城市生活垃圾收集与运输路线的优化模型与方法及其研究进展,通过各种模型与方法的对比,指出它们的优点与存在的问题。借鉴已有的研究思路与方法,引出作者对优化城市生活垃圾收运路线的思路并给出深入研究的建议。     

Public–Private Partnerships for Solid Waste Management Services

The increasing cost of municipal solid waste (MSW) management has led local governments in numerous countries to examine if this service is best provided by the public sector or can better be provided by the private sector. Public–private partnerships have emerged as a promising alternative to improve MSW management performance with privately owned enterprises often outperforming publicly owned ones. In Lebanon, several municipalities are transforming waste management services from a public service publicly provided into a public service privately contracted. In this context, a regulated private market for MSW management services is essential. The present study examines a recent experience of the private sector participation in MSW management in the Greater Beirut Area. The results of a field survey concerning public perception of solid waste management are presented. Analysis of alternatives for private sector involvement in waste management is considered and management approaches are outlined.     

Public-private partnerships for solid waste management services

The increasing cost of municipal solid waste (MSW) management has led local governments in numerous countries to examine if this service is best provided by the public sector or can better be provided by the private sector. Public-private partnerships have emerged as a promising alternative to improve MSW management performance with privately owned enterprises often outperforming publicly owned ones. In Lebanon, several municipalities are transforming waste management services from a public service publicly provided into a public service privately contracted. In this context, a regulated private market for MSW management services is essential. The present study examines a recent experience of the private sector participation in MSW management in the Greater Beirut Area. The results of a field survey concerning public perception of solid waste management are presented. Analysis of alternatives for private sector involvement in waste management is considered and management approaches are outlined.     

A Successful Pilot Project of Decentralized Household Waste Management in Brazil

Summary Present municipal waste management paradigms in Brazil do not allow for flexible approaches to solving an extremely dynamic problem. This paper discusses the basic flaws in present thinking models of residents and municipal administrators. Fundamental arguments presented on municipal solid waste relate to nomenclature, destinations, definitions, logistics, social dynamics, social assistance programs, education and employment philosophies. In each case, the consequences of the stalemate are explained in terms of the unsustainable situation of constantly growing landfills. In sequence, a proactive thinking model is presented and explained that has the potential of drastically reducing landfill size. It is called Municipal Transit Material Processing. The model has been tested successfully in small communities and is now available for scale-up. The landfill diversion achieved stands at 62% of household waste in comparison with 15% theoretically possible in Brazil with selective collection models. Although of necessity the arguments apply directly to Brazil, the basic ideas behind the reasoning may be extrapolated to other Southern countries. The following simple example will illustrate to the reader the type of paradigm inversion the paper proposes to convey. The classical political slogan in Brazil is “get children out of garbage dumps”. The inversion proposed and explained is “do away with garbage dumps”.     

Phosphorus recovery and recycling from waste: An appraisal based on a French case study

Phosphate rocks, used for phosphorus (P) fertilizer production, are a non-renewable resource at the human time scale. Their depletion at the global scale may threaten global food and feed security. To prevent this depletion, improved P resource recycling from food chain waste to agricultural soils and to the food and feed industry is often presented as a serious option. However, waste streams are often complex and their recycling efficiency is poorly characterized. The aim of this paper is to estimate the P recovery and recycling potential from waste, considering France as a case study. We assessed the P flows in food processing waste, household wastewater and municipal waste at the country scale using a substance flow analysis for the year 2006. We also quantified the P recycling efficiency as the fraction of P in waste that ultimately reached agricultural soils or was recycled in the food and feed industry. Efforts were made to limit data uncertainty by cross-checking multiple data sources concerning P content in waste materials. Results showed that, in general, P recovery in waste was high but that the overall P recycling efficiency was only 51% at the country scale. In particular, P recycling efficiency was 75% for industrial waste, 43% for household wastewater and 47% for municipal waste. The remaining P was discharged into water bodies or landfilled, causing P-induced environmental problems as well as losses of nutrient resources. Major P losses were through food waste (which amounted to 39% of P in available food) and treated wastewater, and the findings were confirmed through cross-checking with alternative data sources. Options for improving P resource recycling and, thereby, reducing P fertilizer use were quantified but appeared to be less promising than scenarios based on reduced food waste or redesigned agricultural systems.     

Municipal solid waste generation in Kathmandu, Nepal

Waste stream characteristics must be understood to tackle waste management problems in Kathmandu Metropolitan City (KMC), Nepal. Three-stage stratified cluster sampling was used to evaluate solid waste data collected from 336 households in KMC. This information was combined with data collected regarding waste from restaurants, hotels, schools and streets. The study found that 497.3 g capita(-1) day(-1) of solid waste was generated from households and 48.5, 113.3 and 26.1 kg facility(-1) day(-1) of waste was generated from restaurants, hotels and schools, respectively. Street litter measured 69.3 metric tons day(-1). The average municipal solid waste generation rate was 523.8 metric tons day(-1) or 0.66 kg capita(-1) day(-1) as compared to the 320 metric tons day(-1) reported by the city. The coefficient of correlation between the number of people and the amount of waste produced was 0.94. Key household waste constituents included 71% organic wastes, 12% plastics, 7.5% paper and paper products, 5% dirt and construction debris and 1% hazardous wastes. Although the waste composition varied depending on the source, the composition analysis of waste from restaurants, hotels, schools and streets showed a high percentage of organic wastes. These numbers suggest a greater potential for recovery of organic wastes via composting and there is an opportunity for recycling. Because there is no previous inquiry of this scale in reporting comprehensive municipal solid waste generation in Nepal, this study can be treated as a baseline for other Nepalese municipalities.     

Challenges facing the sustainable consumption and waste management agendas: perspectives on UK households

The management of municipal waste is one of the most emotive local environmental issues in the UK at present and represents a key sustainability “battleground” as local authorities seek to reduce waste arisings and encourage the reuse and recycling of materials among households. Within the literature on household waste management, a broad range of disciplinary perspectives and practical recommendations exist and it is the aim of this paper to step back and take stock of the role of households and communities in resource consumption and waste generation patterns across the UK within recent decades. By exploring the household in this context, trends in consumption and waste generation are outlined in addition to key influencing factors such as lifestyles and well-being, demographics and environment. Finally, key lessons learnt, challenges faced going forward and approaches for developing more sustainable practices at the household, community and national levels are discussed.     

Waste separation at home: Are Japanese municipal curbside recycling policies efficient?

Recent studies have predicted that the costs and benefits of curbside recycling programs will vary considerably across municipalities. In this paper, we examine how the characteristics of municipalities are reflected in curbside recycling policies. Our analysis of Japanese municipal data reveals that municipalities implement recycling programs that fit the demographic profiles of their residents. Municipalities with a considerable number of single-recycler households tend to implement simple waste separation programs. The labor market positions of spouses have different impacts on recycling policies. We further find that the municipalities implementing comprehensive recycling programs collect plastic bottles and containers more frequently than do other municipalities. This implies that the municipalities need to take measures to effectively execute comprehensive recycling programs after implementing them.