Selective supercritical fluid extraction as a tool for determining the PCB fraction accessible for uptake by chironomid larve in a limnic sediment

Selective supercritical fluid extraction (SFE) at 40 degrees C, 400 bar and 60 min was used to selectively remove bioavailable PCBs from a naturally contaminated limnic sediment. The extraction decreased the sediment concentrations of the nine studied PCBs by 54% (on average). Chironomid larvae were thereafter cultured in pre-extracted sediment as well as in untreated sediment to study the differences in uptake of PCBs in the two cultures. While the prevailing equilibrium partitioning (EqP) theory predicts a 54% decrease in PCB uptake by the chironomids in the pre-extracted sediment, with a maintained biota-to-sediment accumulation factor (BSAF), a decrease in PCB uptake by 91% was observed. For all investigated PCBs the BSAFs were on average 81% lower in the cultures with pre-extracted sediment than in the untreated systems. The data allowed for a calculation of the bioavailable fraction, which was estimated to 60%. This is very close to the 54% removed by selective SFE, demonstrating the possibility of using SFE as a tool to determine the bioavailable PCB fraction in a polluted sediment.     

Selective supercritical fluid extraction to identify aged sediment-bound PCBs available for uptake by eel

A naturally contaminated sediment was partially extracted with selective supercritical fluid extraction (SFE) to remove a fraction of supposedly bioavailable PCBs from the matrix. Eels (Anguilla anguilla) were cultured in systems with untreated and pre-extracted sediment, respectively, and it was shown that the SFE treatment selectively removed bioavailable PCBs from the sediment, since relative biota-to-sediment accumulation factors (BSAFs) for the eight studied PCB congeners were much lower in the pre-extracted than in the untreated system at the end of the study. Relative BSAF values decreased with about the same relative amount for all eight congeners, independent of the degree of chlorination and the initial concentration in the sediment. The results demonstrate the ability of SFE to selectively remove sediment-bound PCBs that are available for uptake by the eels, thus demonstrating the feasibility of using selective SFE to estimate bioavailability of PCBs in sediments.     

Selective supercritical fluid extraction to estimate the fraction of PCB that is bioavailable to a benthic organism in a naturally contaminated sediment

Selective supercritical fluid extraction (SFE) at 40 degrees C, 120 bar and 60 min was utilised as a means to estimate the bioavailable fraction of PCBs to chironomid larvae in a naturally contaminated limnic sediment. This extraction methodology removed about 50% of the PCBs from the sediment. According to the equilibrium partitioning theory, organisms in that sediment should decrease their uptake from the sediment to the same extent, biota-to-sediment accumulation factors (BSAFs) thus remaining constant. Surprisingly, the BSAFs for 11 PCB congeners decreased some 40% for the selectively extracted sediment as compared to BSAFs for organisms dwelling in untreated sediment. The results were statistically significant at the 0.001 level using a paired t-test. This can only be interpreted so that selective SFE removed easily available PCBs preferentially, leaving more tightly bound PCBs behind. Hence, by fine-tuning extraction conditions, this methodology might be used to estimate bioavailable fractions by chemical means.     

Influence of activated carbon amendment on the accumulation and elimination of PCBs in the earthworm Eisenia fetida

In this study we investigated the use of activated carbon (AC) as a soil amendment for reducing bioavailability of polychlorinated biphenyls (PCBs) to the earthworm Eisenia fetida. Artificial soil was contaminated with PCBs and used in bioaccumulation experiments fresh or after aging for 19 months. PCB bioaccumulation in earthworms was reduced by 68% when AC was placed as a layer without mixing and by 94% when AC was manually mixed into the soil. Aging of the same AC mixed soil for 19 months resulted in an overall reduction of 99% in PCB biouptake. AC-treated aged soil also showed two orders of magnitude lower equilibrium aqueous concentrations of PCBs compared to untreated aged soils. The findings from this study indicate that application of engineered sorbents like AC to PCB impacted soils may greatly reduce PCB uptake at the base of the terrestrial food chain.     

Investigation of polychlorinated biphenyl removal from contaminated soil using microwave-generated steam

A feasibility study of polychlorinated biphenyl (PCB) removal from contaminated soils using microwave-generated steam (MGS) was performed. Initial experimental results show that MGS effectively removed PCBs from contaminated soil with an overall removal efficiency of greater than 98% at a steam-to-soil mass ratio of 3:1. Removal efficiency was found to be dependent upon the amount of steam employed, expressed as a mass ratio of steam applied to soil mass. Evaporation was identified as a major mechanism in removing PCBs from the soil. Rapid expansion and evaporation of pore water by microwave dielectric heating accelerated evaporation rates of PCB molecules. Increased solubility of PCBs into the heated aqueous phase is also hypothesized. Together these effects increase mass-transfer rates, thus enhancing removal of PCBs from the soil.     

Development of a simple selective SFE method for the determination of desorption behaviour of PCBs in two Swedish sediments

A simple selective supercritical fluid extraction (SFE) method was developed for the determination of desorption behaviour of PCBs in sediments. This method was applied to determine the distribution of individual PCB congeners among sites of differing bonding strengths in two Swedish sediments (Lake J?rnsj?n and Baltic bay Orserumsviken). Four different PCB fractions were distinguished in each sediment by applying consecutively harsher supercritical fluid extraction conditions on the same sample. Even though the two sediments had completely different textures, they showed very similar extraction behaviour. It was shown that, in both sediments, a major part of the PCBs (58% and 65%, respectively) were located at "fast sites", from which they were extractable already with the mildest extraction conditions (60 min, 40 degrees C and 120 bar). Only a small fraction of the PCBs were so tightly bound to the sediments (located at "slow sites"), that they could be extracted only under the harshest conditions (60 min, 150 degrees C and 400 bar). Information of this kind should be of great value for the determination of bioavailability of pollutants in sediments and soils, and it is the author's belief that this technique has the potential to develop into a powerful tool in environmental risk assessment.     

In Memoriam

ABSTRACT

A feasibility study of polychlorinated biphenyl (PCB) removal from contaminated soils using microwave-generated steam (MGS) was performed. Initial experimental results show that MGS effectively removed PCBs from contaminated soil with an overall removal efficiency of greater than 98% at a steam-to-soil mass ratio of 3:1. Removal efficiency was found to be dependent upon the amount of steam employed, expressed as a mass ratio of steam applied to soil mass. Evaporation was identified as a major mechanism in removing PCBs from the soil. Rapid expansion and evaporation of pore water by microwave dielectric heating accelerated evaporation rates of PCB molecules. Increased solubility of PCBs into the heated aqueous phase is also hypothesized. Together these effects increase mass-transfer rates, thus enhancing removal of PCBs from the soil.     

Simultaneous mobilization of heavy metals and polychlorinated biphenyl (PCB) compounds from soil with cyclodextrin and EDTA in admixture

This study evaluated the efficacy of a washing process with cyclodextrin in combination with ethylenediaminetetraacetate (EDTA) for the simultaneous mobilization of heavy metals and PCBs from a field contaminated soil. Ultrasonically aided mixing of the field contaminated soil with a combination of cyclodextrin solution (10%, w/v) and a sparing quantity (2 mmol) of EDTA, simultaneously mobilized appreciable quantities of PCBs and much of the analyte metal (Cd, Cr, Cu, Mn, Ni, Pb, Zn) burdens. Relative to the action of individual reagents, a combination of randomly methylated (RAMEB) or hydroxypropyl beta-cyclodextrin (HPCD) with EDTA did not alter the PCB extraction efficiency nor did the presence of cyclodextrin change the efficiency of mobilization of most heavy metals (Al, Cd, Cr, Fe, Mn, Ni, and Zn) but did increase the recovery of Cu and Pb modestly. Three sonication-washes with the same charge of reagents mobilized appreciable quantities of PCBs (40-76%) and quantitatively extracted the labile fraction of Cd, Cu, Mn, and Pb. RAMEB proved to be more efficient than HPCD for PCB extractions. Three successive extractions with a single charge of cyclodextrin mobilized almost as much PCB (RAMEB, 76%; HPCD, 40%) as did the companion extractions that used fresh reagents each time (RAMEB, 78%; HPCD, 42%). Collectively, these studies demonstrated that PCB compounds and selected heavy metals can be co-extracted efficiently from soil with three successive washes with the same washing suspension containing EDTA and cyclodextrin.     

Dynamics of PCB removal and detoxification in historically contaminated soils amended with activated carbon

Activated carbon (AC) can help overcome toxicity of pollutants to microbes and facilitate soil bioremediation. We used this approach to treat a Histosol and an Alluvial soil historically contaminated with PCB (4190 and 1585 mg kg⁻¹, respectively; primarily tri-, tetra- and pentachlorinated congeners). Results confirmed PCB persistence; reductions in PCB extractable from control and AC-amended soils were mostly due to a decrease in tri- and to some extent tetrachlorinated congeners as well as formation of a bound fraction. Mechanisms of PCB binding by soil and AC were different. In addition to microbial degradation of less chlorinated congeners, we postulate AC catalyzed dechlorination of higher chlorinated congeners. A large decrease in bioavailable PCB in AC-amended soils was demonstrated by greater clover germination and biomass. Phytotoxicity was low in treated soils but remained high in untreated soils for the duration of a 39-month experiment. These observations indicate the utility of AC for remediation of soils historically contaminated with PCB.     

Study of transportation and distribution of PCBs using an ecologically simulated growth chamber

This study was designed to investigate the transportation, distribution, and bioaccumulation of PCBs in various environmental media and compartments using an ecologically simulated growth chamber. Spatial and temporal trends of PCBs in the growth chamber were discussed. The release of PCB congeners in soil was affected by the amount of rainfall with the transporting direction moving away from PCBs contaminated point. Two pathways of PCBs accumulation in plants were the uptake of roots and the deposition on shoots/leaves. There were 29 PCB congeners been found in the lalang grass. Higher concentrations of lower chlorinated PCBs were identified than higher chlorinated PCBs because of relatively higher vapor pressure for lower chlorinated congeners. After 10months of monitoring, PCBs were detected in water samples which were contributed by the release of PCBs from leached soil. Analysis of sediment showed that the percentages of low- and mid-chlorinated biphenyls were decreased 1% and 13%, respectively compared to the increase (14%) of high-chlorinated biphenyls. The increase of high-chlorinated PCBs was possibly caused by their low hydrophilicity which had resulted higher adsorption rate in sediment. All of five species of fish had been found significant amount of PCBs accumulation ( summation operatorPCBs: 21.7-102.1 microg/g-lipid). The concentrations of PCBs in fish were varied significantly among species. The range of bioaccumulation factors (BAFs) among different species of fish could be as much as 5 times depending on the consumption habits of fish. The mass balance of PCBs distribution in the growth chamber was also discussed.     

Study of the distribution of the polychlorinated biphenyls in the milk fat globule by supercritical fluid extraction

The distribution of polychlorinated biphenyls (PCBs) in the milk fat globule has been studied by sequential extraction of four different lipidic fractions from powdered full-fat milk with supercritical carbon dioxide. Extractions were carried out in the dynamic mode in the pressure range 13.6-23.3 MPa at a temperature of 50 degrees C. The levels of PCBs and short-chain triglycerides (SCT), medium-chain triglycerides (MCT) and long-chain triglycerides (LCT), as well as the cholesterol in these four supercritical fluid extraction (SFE) fractions were determined. Extracts obtained at lower pressures were found to be enriched in PCBs, SCT, MCT and cholesterol, while the concentrations of all these analytes decreased for subsequent extractions. Satisfactory quadratic correlations were found between the PCB and SCT and MCT levels (r2 in the range 0.9-0.999), and between the PCB and cholesterol levels (r2 in the range 0.8-0.999, except for PCB 105) determined in the SFE fractions. These results suggested a similar distribution of the PCBs and the cholesterol in the milk fat globule. This conclusion was also supported by the comparison of the PCBs and the cholesterol chemical structures as well as by the total PCB levels determined by SFE to those obtained by using different extraction methods. The classical requirement for the analysis of this kind of lipophilic pollutants of an exhaustive extraction of the lipids of the matrix to ensure their quantitative recovery has been revised.     

Application of microwave irradiation in the removal of polychlorinated biphenyls from soil contaminated by capacitor oil

The applicability of microwave irradiation in the removal of polychlorinated biphenyls (PCBs) from the soil heavily contaminated by capacitor oil was studied. Granular activated carbon (GAC) was added into the soil as a microwave-absorbing material to rapidly increase the temperature of the reaction system. Effects of sodium hypophosphite (SHP) and iron powder (IP) as reductants on PCB removal, as well as the effects of water content in soil, microwave power and the amount of GAC added were investigated. The results indicated that in the presence of SHP and GAC, about 80% of PCBs in soil were effectively removed by 10 min microwave irradiation, and the further addition of IP could raise the average removal efficiency to a higher level, more than 95%. In the removal of PCBs with the microwave/GAC/IP/SHP system, an appropriate amount of water proved to be helpful in promoting the removal of PCBs from soil by steam distillation and in acting as a co-solvent of SHP and H-donor of IP.     

Comparison of supercritical fluid extraction and Soxhlet extraction for the determination of PCBs in seaweed samples

The efficiency of supercritical fluid extraction for the determination of 12 polychlorinated biphenyls from algae samples is compared to Soxhlet extraction. Analytical detection limits for the individual congeners ranged from 0.62 microgl(-1) to 19 microgl(-1). Recovery was tested for both methods using standard addition procedure. At maximum spike level of concentration, the mean recoveries were not significantly different (P>0.05) of all PCBs studied, with the exception of PCBs 28, 52, 77 and 169. Method precision for Soxhlet extraction (< or =3.9%) was slightly better than for SFE (< or =9.2%). Although both methods yield comparable results, SFE offers the advantage of detecting all PCBs studied at lower concentrations, reducing extraction time, and reducing the amount of solvents needed. The optimized methods were applied to the analysis of three real seaweed samples, except for PCB101 the concentrations of all PCBs were low or below the detection limits. The levels of PCB101 found in sample 1 were 6.6+/-0.54 ng g(-1) d.w., in sample 2 the levels were 8.2+/-0.86 ng g(-1) d.w. and in sample 3 they were 7.7+/-0.08 ng g(-1) d.w.     

In vitro approaches to assess bioavailability and human gastrointestinal mobilization of food-borne polychlorinated biphenyls (PCBs)

This study reports on the potential for gastrointestinal (GI) mobilization and bioavailability of food-borne PCBs in humans. The development and validation of a GI simulator and operational protocols, developed in compliance with the requirements of German DIN 19738 risk assessment test procedure, are presented. Food, naturally contaminated with PCBs, was homogenized with simulated saliva fluid and shaken in the GI simulator with simulated gastric fluids (containing pepsin, mucine) for 2 h at 37°C. Afterwards, the simulated intestinal fluids (containing pepsin, mucine, trypsin, pancreatin, bile) were added and the mixture shaken for a further 6 h prior to centrifugation and filtration using Buchner funnels to separate the undigested GI residues from GI fluids. PCBs were recovered from GI residues and fluids by Soxhlet and liquid-liquid extraction respectively, cleaned up using silica-SFE, and analyzed by gas chromatography mass spectrometry detection (GC-MSD). Detailed studies with fish indicate variations in mobilization and bioavailability of Σ PCBs (28, 52, 101, 118, 153, 138 and 180). For example, the bioavailable fractions (fractions mobilized) in mackerel, salmon, crab and prawn were 0.77, 0.60, 0.54, and 0.72 respectively of the Σ PCBs initially present in these food samples. The bioavailable fraction was dependent on the physicochemical characteristics of the PCBs. In mackerel bioavailable fractions for individual PCB congeners ranged from 0.47–0.82, from 0.30–0.70 in salmon, 0.44–0.64 in crab and in prawn from 0.47–0.77. Future studies will focus on understanding better, the variability in bioavailable fractions to be expected for different foodstuffs, in addition to tissue culture techniques using human gut cell lines to investigate a simultaneous mobilization and absorption of food-borne PCBs.     

In vitro approaches to assess bioavailability and human gastrointestinal mobilization of food-borne polychlorinated biphenyls (PCBs)

This study reports on the potential for gastrointestinal (GI) mobilization and bioavailability of food-borne PCBs in humans. The development and validation of a GI simulator and operational protocols, developed in compliance with the requirements of German DIN 19738 risk assessment test procedure, are presented. Food, naturally contaminated with PCBs, was homogenized with simulated saliva fluid and shaken in the GI simulator with simulated gastric fluids (containing pepsin, mucine) for 2 h at 37 degrees C. Afterwards, the simulated intestinal fluids (containing pepsin, mucine, trypsin, pancreatin, bile) were added and the mixture shaken for a further 6 h prior to centrifugation and filtration using Buchner funnels to separate the undigested GI residues from GI fluids. PCBs were recovered from GI residues and fluids by Soxhlet and liquid-liquid extraction respectively, cleaned up using silica-SFE, and analyzed by gas chromatography mass spectrometry detection (GC-MSD). Detailed studies with fish indicate variations in mobilization and bioavailability of Sigma PCBs (28, 52, 101, 118, 153, 138 and 180). For example, the bioavailable fractions (fractions mobilized) in mackerel, salmon, crab and prawn were 0.77, 0.60, 0.54, and 0.72 respectively of the Sigma PCBs initially present in these food samples. The bioavailable fraction was dependent on the physicochemical characteristics of the PCBs. In mackerel bioavailable fractions for individual PCB congeners ranged from 0.47-0.82, from 0.30-0.70 in salmon, 0.44-0.64 in crab and in prawn from 0.47-0.77. Future studies will focus on understanding better, the variability in bioavailable fractions to be expected for different foodstuffs, in addition to tissue culture techniques using human gut cell lines to investigate a simultaneous mobilization and absorption of food-borne PCBs.     

Assessing the potential for rhizoremediation of PCB contaminated soils in northern regions using native tree species

Rhizosphere bioremediation of polychlorinated biphenyls (PCBs) offers a potentially inexpensive approach to remediating contaminated soils that is particularly attractive in remote regions including the Arctic. We assessed the abilities of two tree species native to Alaska, Salix alaxensis (felt-leaf willow) and Picea glauca (white spruce), to promote microbial biodegradation of PCBs via the release of phytochemicals upon fine root death. Crushed fine roots, biphenyl (PCB analogue) or salicylate (willow secondary compound) were added to microcosms containing soil spiked with PCBs and resultant PCB disappearance, soil toxicity and microbial community changes were examined. After 180 d, soil treated with willow root crushates showed a significantly greater PCB loss than untreated soils for some PCB congeners, including the toxic congeners, PCB 77, 105 and 169, and showed a similar PCB loss pattern (in both extent of degradation and congeners degraded) to biphenyl-treated microcosms. Neither P. glauca (white spruce) roots nor salicylate enhanced PCB loss, indicating that biostimulation is plant species specific and was not mediated by salicylate. Soil toxicity assessed using the Microtox bioassay indicated that the willow treatment resulted in a less toxic soil environment. Molecular microbial community analyses indicated that biphenyl and salicylate promoted shifts in microbial community structure and composition that differed distinctly from each other and from the crushed root treatments. The biphenyl utilizing bacterium, Cupriavidus spp. was isolated from the soil. The findings suggest that S. alaxensis may be an effective plant for rhizoremediation by altering microbial community structure, enhancing the loss of some PCB congeners and reducing the toxicity of the soil environment.     

Seasonal variation of the distribution of PCBs in sediments and biota in a PCB-contaminated estuary

To elucidate the effects of seasonal variation of precipitation on the distribution of polychlorinated biphenyls (PCBs) in estuarine sediments and benthic feeders, PCB concentrations of river surface sediments and mullet fish (Liza macrolepis) were investigated in the estuary of Er-Jen River near former PCB contamination sites before and after each wet season from 2002 to 2004. Analyses of grain size distribution and organic matter revealed that the pre-existing surface sediments were covered by and mixed with the soil particulates brought by surface runoff after each wet season. Obvious increment of PCB content and significantly elevated fraction (p < 0.005) of light PCBs of the river mouth’s sediments after each wet season indicated that the invading particles were rich in unweathered PCBs. PCBs previously buried in the surface soil of heavily contaminated sites were flushed into this estuary through surface runoff. The precipitation altered the PCB patterns in sediment organic matter, the dietary source of mullet, and consequently changed that of mullets accordingly, which all possessed significant greater fraction of light PCBs. In this study, it was demonstrated that seasonal summer precipitation affected the distribution of PCBs on surface sediments and the mullets of this estuary. PCB residuals retained in this region still pose potential threats to biota resided here.     

Investigating differential binding of polychlorinated dibenzo-p-dioxins/dibenzofurans in soil and soil components using selective supercritical fluid extraction

Supercritical fluid extraction (SFE) with pure carbon dioxide was performed at increasingly strong conditions to investigate differential binding of polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) in two impacted soils, in their sieved size fractions, and in small (a few mg) samples of industry-related waste products separated from impacted soil. The binding strengths of PCDD/Fs were shown to be different in the two soils, and in their different soil particle size fractions. As might be expected based on surface area considerations, one soil showed the strongest binding in the smallest (<5 μm) sieved fraction. However, the other soil showed the strongest binding in the larger sized fractions, possibly indicating that process-related particles could be controlling PCDD/F binding. Selective SFE of various types of particles including black carbon and charcoal (separated from soil), and from a suspected process anode residue did show different PCDD/F binding behavior ranging from quite weak binding (charcoal) to very strong binding (anode particles). Shifts to the stronger SFE fractions in the soils after activated carbon treatment agreed well with the decreases previously found in the uptake of PCDD/Fs by earthworms, as well as decreases in their freely-dissolved aqueous concentrations in soil/water slurries. These results show that, as previously demonstrated for PAHs and PCBs, selective SFE can be a useful tool to investigate differences in PCDD/F binding behaviors in impacted soils and sediments and their component parts, as well as a rapid tool for estimating the effectiveness of activated carbon treatments on decreasing the bioavailability of PCDD/Fs in soils and sediments.     

TiO2 photocatalytic degradation of PCBs in soil-water systems containing fluoro surfactant

Titanium dioxide-mediated photodegradation of Polychlorinated biphenyls (PCBs) in soil/aqueous systems with added fluorinated surfactant was investigated. PCBs can bind tightly to organic matter in the soil, especially in aged, contaminated soil. Experiments showed an effective PCB photocatalytic degradation in mixed systems of soil/clay with anionic fluorinated surfactant FC-143 and TiO2. The FC-143 surfactant is stable in this photochemical process. PCB degradation rates in samples followed the order: spiked clay > spiked soil > Hudson River bank soil. The results suggest that anionic fluorinated surfactant may form semimicelles and/or admicelles on the surface of positively charged TiO2. The hydrophobic surface of TiO2 can provide a nonpolar phase that acts as a partioning medium for hydrophobic PCBs. Therefore, PCBs in soil can be released to the semimicelle and/or admicelle on the TiO2 surface and are effectively photodegraded in a dispersion containing anionic fluorinated surfactant. The combination of surfactant extraction and photooxidation forms the basis for a novel two-stage process for the removal and destruction of PCBs from soil.     

Life cycle of PCBs and contamination of the environment and of food products from animal origin

This report gives a summary of the historic use, former management and current release of polychlorinated biphenyls (PCBs) in Germany and assesses the impact of the life cycle of PCBs on the contamination of the environment and of food products of animal origin. In Germany 60,000 t of PCBs were used in transformers, capacitors or as hydraulic oils. The use of PCB oils in these “closed applications”, has been banned in Germany in 2000. Thirty to 50% of these PCBs were not appropriately managed. In West Germany, 24,000 t of PCBs were used in open applications, mainly as additive (plasticiser, flame retardant) in sealants and paints in buildings and other construction. The continued use in open applications has not been banned, and in 2013, an estimated more than 12,000 t of PCBs were still present in buildings and other constructions. These open PCB applications continuously emit PCBs into the environment with an estimated release of 7–12 t per year. This amount is in agreement with deposition measurements (estimated to 18 t) and emission estimates for Switzerland. The atmospheric PCB releases still have an relevant impact on vegetation and livestock feed. In addition, PCBs in open applications on farms are still a sources of contamination for farmed animals. Furthermore, the historic production, use, recycling and disposal of PCBs have contaminated soils along the lifecycle. This legacy of contaminated soils and contaminated feed, individually or collectively, can lead to exceedance of maximum levels in food products from animals. In beef and chicken, soil levels of 5 ng PCB-TEQ/kg and for chicken with high soil exposure even 2 ng PCB-TEQ/kg can lead to exceedance of EU limits in meat and eggs. Areas at and around industries having produced or used or managed PCBs, or facilities and areas where PCBs were disposed need to be assessed in respect to potential contamination of food-producing animals. For a large share of impacted land, management measures applicable on farm level might be sufficient to continue with food production. Open PCB applications need to be inventoried and better managed. Other persistent and toxic chemicals used as alternatives to PCBs, e.g. short chain chlorinated paraffins (SCCPs), should be assessed in the life cycle for exposure of food-producing animals and humans.