Solar-induced generation of singlet oxygen and hydroxyl radical in sewage wastewaters

Singlet oxygen (¹O₂) and hydroxyl radical (·OH) play an important role in the degradation of pollutants in surface waters. However, the mechanism underlying the photochemical generation of ¹O₂ and ·OH in wastewaters is poorly known. Here we studied the photo-induced generation of ¹O₂ and ·OH in different sewage treatment plant units. The correlation between the generation of ¹O₂ and ·OH and the water constituents was discussed. Our results show that in sewage units the ¹O₂ formation rate ranges from 2.19 × 10^?8 to 6.74 × 10^?8 mol L^?1 s^?1, and the ·OH formation rate ranges from 1.7 × 10^?11 to 3.06 × 10^?10 mol L^?1 s^?1. The average ¹O₂ formation rates in the various sewage units are similar to those in wetland and estuarine waters containing rich dissolved organic matter and 2–4 times higher than those in lake and seawater samples. The average ·OH formation rates of the sewage units are 5–50 times higher than for other water samples reported. The ·OH generation rate increased with the iron content with a correlation coefficient of 0.85, which indicates that the photo-Fenton reaction plays a dominant role in ·OH generation in sewage wastewater.     

Depollution of indigo dye by anodic oxidation and electro-Fenton using B-doped diamond anode

Hazardous wastes are generated in the synthesis of dyes and pigments applied in industries. Efficient methods are thus needed to clean wastewaters. Here, we use anodic oxidation and electro-Fenton with B-doped diamond anode to degrade the synthetic dye indigo in aqueous sodium dithionite. Results show the near-complete mineralization of the dye within 80 min at 500 mA. Mineralization was faster by electro-Fenton than anodic oxidation. The second-order rate constant (k) for the reaction of indigo with ^·OH was measured as 4.03 × 10⁹ M^?1 s^?1 at pH 3.0 and was compared with the rate constants of reactions between dyes and ^·OH. The results clearly demonstrate that both electro-Fenton and anodic oxidation can be used to depollute dyes in textile effluent with high efficiency and low cost. The main oxidant, ^·OH, being a non-selective reagent, the method could be applied to degrade other organic pollutants.     

Air pollution below WHO levels decreases by 40 % the links of terrestrial microbial networks

Air pollution has a deleterious impact on public health and the environment. There is few knowledge on the effect of air pollution on terrestrial microbial communities, despite the major role of microbes in ecosystems. Here, we designed an in situ trial ecosystem to assess the impact of moderate atmospheric pollution, below World Health Organization (WHO) thresholds, on an indigenous microbial communities, including bacteria, fungi, ciliates, algae, cyanobacteria, testate amoebae, rotifers and nematodes, extracted from terrestrial bryophytes. These micro-ecosystems were placed at a rural, an urban and an industrial site in France and were thus exposed to various levels of nitrogen dioxide (NO₂), from 6.6–67.9 μg·m^?3, and particulate matter, from 0.7–7.9 μg·m^?3. Microbial analysis was performed by microscopy. We determined atmospheric temperature, relative humidity and particulate matter with diameter lower than 10 µm (PM₁₀), Cu, Cr, Fe, Ni, Pb, Zn in PM₁₀, and (NO₂). Results show a significant impact of chronic moderate exposure to NO₂ and copper Cu-associated particulate matter on the global microbial network complexity. This is evidenced by a loss of about 40 % of microbial co-occurrence links during incubation. Most lost microbial links are ecologically positive links. Moreover, most changes in community co-occurrence networks are related to testate amoebae, a major top predator of microbes. Overall, our findings demonstrate that air pollution can have strong deleterious effects on microbial interactions, even at levels below WHO thresholds.     

Geochemistry and quality of groundwater of the Yarmouk basin aquifer,north Jordan

Quality of groundwater in the Yarmouk basin, Jordan has been assessed through the study of hydrogeochemical characteristics and the water chemistry as it is considered the main source for drinking and agriculture activities in the region. The results of the relationship between Ca²⁺ + Mg²⁺ versus HCO₃^? + CO₃^2?, Ca²⁺ + Mg²⁺ versus total cations, Na⁺ + K⁺ versus total cations, Cl^? + SO₄^2? versus Na⁺ + K⁺, Na⁺ versus Cl^?, Na⁺ versus HCO₃^? + CO₃^2?, Na⁺ versus Ca²⁺, and Na⁺: Cl^? versus EC describe the mineral dissolution mechanism through the strong relationship between water with rocks in alkaline conditions with the release of Ca²⁺, Mg²⁺, Na⁺, K⁺, HCO₃^?, CO₃^2?, SO₄^2?, and F^? ions in the groundwater for enrichment. Furthermore, evaporation processes, groundwater depletion, and ion exchange contribute to the increased concentration of Na⁺ and Cl^? ions in groundwater. Anthropogenic sources are one of the main reasons for contamination of groundwater in the study area and for increasing the concentration of Mg²⁺, Na⁺, Cl^?, SO₄^2?, and NO₃^? ions. Results show the quality of groundwater in the study area is categorized as follows: HCO₃^? + CO₃^2? > Cl^? > SO₄^2? > NO₃^? > F^? and Na⁺ > Ca²⁺ > Mg²⁺ > K⁺. In conclusion, the results of TDS, TH, and chemical composition showed that 26% of the groundwater samples were unsuitable for drinking. About 28% of groundwater samples in the study area have a high concentration of Mg²⁺, Na⁺, and NO₃^? above the acceptable limit. Also, based on high SAR, 10% of the groundwater samples were not suitable for irrigation purposes.     

Chemically modified biochar produced from conocarpus waste increases NO<Subscript>3</Subscript> removal from aqueous solutions

Biochar has emerged as a universal sorbent for the removal of contaminants from water and soil. However, its efficiency is lower than that of commercially available sorbents. Engineering biochar by chemical modification may improve its sorption efficiency. In this study, conocarpus green waste was chemically modified with magnesium and iron oxides and then subjected to thermal pyrolysis to produce biochar. These chemically modified biochars were tested for NO₃ removal efficiency from aqueous solutions in batch sorption isothermal and kinetic experiments. The results revealed that MgO-biochar outperformed other biochars with a maximum NO₃ sorption capacity of 45.36 mmol kg^?1 predicted by the Langmuir sorption model. The kinetics data were well described by the Type 1 pseudo-second-order model, indicating chemisorption as the dominating mechanism of NO₃ sorption onto biochars. Greater efficiency of MgO-biochar was related to its high specific surface area (391.8 m² g^?1) and formation of strong ionic complexes with NO₃. At an initial pH of 2, more than 89 % NO₃ removal efficiency was observed for all of the biochars. We conclude that chemical modification can alter the surface chemistry of biochar, thereby leading to enhanced sorption capacity compared with simple biochar.     

Fast and complete removal of the 5-fluorouracil drug from water by electro-Fenton oxidation

Cytostatic drugs are a troublesome class of emerging pollutants in water owing to their potential effects on DNA. Here we studied the removal of 5-fluorouracil from water using the electro-Fenton process. Galvanostatic electrolyses were performed with an undivided laboratory-scale cell equipped with a boron-doped diamond anode and a carbon felt cathode. Results show that the fastest degradation and almost complete mineralization was obtained at a Fe²⁺ catalyst concentration of 0.2 mM. The absolute rate constant for oxidation of 5-fluorouracil by hydroxyl radicals was 1.52 × 10⁹ M^?1 s^?1. Oxalic and acetic acids were initially formed as main short-chain aliphatic by-products, then were completely degraded. After 6 h the final solution mainly contained inorganic ions (NH₄ ⁺, NO₃ ^? and F^?) and less than 10% of residual organic carbon. Hence, electro-Fenton constitutes an interesting alternative to degrade biorefractory drugs.     

Rice seedlings under cadmium stress: effect of silicon on growth,cadmium uptake,oxidative stress,antioxidant capacity and root and leaf structures

In this study, the effect of silicon (Si) addition on cadmium (Cd) toxicity in rice seedlings was investigated. After a series of screening experiments, 50 μmol·L^?1 of Cd and 10 μ mol·L^?1 of Si were selected. Treatment of rice seedlings with Cd (50 μ mol·L^?1) resulted in significant accumulation of this metal in roots and shoots. The data revealed that accumulation of Cd resulted in oxidative stress in rice seedlings as evidenced by increased accumulation of hydrogen peroxide (H₂O₂) and malondialdehyde (MDA; a peroxidation product of lipids). However, addition of Si (10 μ mol·L^?1) together with Cd prevented accumulation of Cd, H₂O₂ and MDA. Antioxidant capacity was decreased by Cd but enhanced by Si addition. Cd decreased the length and frequency of root hairs, stomatal frequency, and distorted leaf mesophyll cells and vascular bundles. However, addition of Si together with Cd reduced these abnormalities. The results showed that addition of exogenous Si protected rice seedlings against Cd toxicity by preventing Cd accumulation and oxidative stress (H₂O₂ and MDA accumulation) by increasing Si accumulation and antioxidant capacity, which maintained the structure and integrity of leaf and root.     

Effects of ethyl 2-methyl acetoacetate (EMA) on the growth of Phaeodactylum tricornutum and Skeletonema costatum

We investigated the effects of ethyl 2-methyl acetoacetate (EMA) on growth of the marine diatom algae Phaeodactylum tricornutum (P. tricornutum) and Skeletonema costatum (S. costatum). Growth of P. tricornutum was significantly inhibited by the minimum concentration (3.5 mmol·L ^?1) of EMA at lower initial algal densities (IADs) (3.6×10⁴ and 3.3×10⁵ cells·mL ^?1). However, at the highest IAD, significant growth inhibition was found at above 7 mmol·L ^?1 of EMA exposure. In S. costatum, EMA concentrations of 10.5 mmol·L ^?1 or more significantly inhibited growth at lower IAD (3×10⁴ and 1.8×10⁵ cells·mL ^?1); at the highest IAD, only EMA concentrations above 14 mmol·L ^?1 obviously inhibited the growth of S. costatum. Changes in specific growth rates and pigment were consistent with algal growth, but only at higher EMA concentrations or lower IAD values was the ratio of chlorophyll a (Chla) to carotenoid significantly lower than the control. Medium effective concentration (EC ₅₀) values were in the order 4.07, 8.03 and 12.27 mmol·L ^?1 for P. tricornutum and 7.48, 11.92 and 17.22 mmol·L ^?1 for S. costatum. All these results show that the effect of EMA on the growth of algae was species specific and mainly depended on IAD, which might be an important factor to influence algal growth.     

Reactivity of sulfate radicals with natural organic matters

Advanced oxidation processes based on sulfate radicals (SO ₄ ^·? ) are capable of efficiently degrade organic pollutants from ground, surface and wastewaters. However, this degradation may be limited by aqueous natural organic matter (NOM). Here we measured the absolute rate constants of reaction of SO ₄ ^·? with four types of organic matter: two fulvic acids and two lake organic matter. We used laser flash photolysis technique to monitor the SO ₄ ^·? decay and the formation of the transients from organic matters. Reaction rate constants comprised between 1530 and 3500 s^?1 mgC^?1 L were obtained by numerical analysis of differential equations and the weighted average of the extinction coefficient of the generated organic matters radicals between 400 and 800 M^?1 cm^?1.     

Geoenvironmental factors related to high incidence of human urinary calculi (kidney stones) in Central Highlands of Sri Lanka

An area with extremely high incidence of urinary calculi was investigated in the view of identifying the relationship between the disease prevalence and the drinking water geochemistry. The prevalence of the kidney stone disease in the selected Padiyapelella–Hanguranketa area in Central Highlands of Sri Lanka is significantly higher compared with neighboring regions. Drinking water samples were collected from water sources that used by clinically identified kidney stone patients and healthy people. A total of 83 samples were collected and analyzed for major anions and cations. The anions in the area varied in the order HCO₃ ^? > Cl^? > SO₄ ^2? > NO₃ ^? and cations varied in the order Ca²⁺ > Mg²⁺ > Na⁺ > K⁺ > Fe²⁺. The dissolved silica that occurs as silicic acid (H₄SiO₄) in natural waters varied from 8.8 to 84 mg/L in prevalence samples, while it was between 9.7 and 65 mg/L for samples from non-prevalence locations. Hydrogeochemical data obtained from the two groups were compared using the Wilcoxon rank-sum test. It showed that pH, total hardness, Na⁺, Ca²⁺ and Fe²⁺ had significant difference (p < 0.005) between water sources used by patients and non-patients. Elemental ratio plots, Gibbs’ plot and factor analysis indicated that the chemical composition of water sources in this area is strongly influenced by rock–water interactions, particularly the weathering of carbonate and silicate minerals. This study reveals a kind of association between stone formation and drinking water geochemistry as evident by the high hardness/calcium contents in spring water used by patients.     

Metabolic responses of Azolla pinnata to cadmium stress: photosynthesis,antioxidative system and phytoremediation

This present study deals with the growth, photosynthesis, oxidative stress and phytoremediation character of Azolla pinnata L. exposed to different levels (0.05, 0.1, 0.5, 1.0, 1.5 and 2.0 mg·L^?1) of cadmium (Cd). Significant accumulation of Cd in Azolla fronds was noticed after 24 and 96 h of exposure and the accumulation rate was dose and time dependent. Growth of A. pinnata increased significantly after both exposure times with and without metal. At lower Cd doses (0.05 and 0.1 mg·L^?1), growth and photosynthesis of A. pinnata showed a marginal increase over the respective control, however, at higher Cd doses (0.5, 1.0, 1.5 and 2.0 mg·L^?1), a decreasing trend was noticed. At lower doses, Azolla fronds could counterbalance the negative effect of enhanced levels of superoxide radicals (SOR) and hydrogen peroxide (H₂O₂) through the greater activity of antioxidative enzymes. The decaresing trends in catalase and peroxidase activity at higher Cd doses suggest that Azolla fronds were not able to mitigate the negative effects of H₂O₂, hence an increase in malondialdehyde content was noticed. The study concludes that up to 0.1 ,mg·L^?1 Cd, A. pinnata can flourish and be used as biofertiliser and for phytoremedial purposes in Cd-contaminated fields; beyond this concentration poor growth may restrict its application.     

Photosynthetic and growth responses of Japanese sasabamo (Potamogeton wrightii Morong) under different photoperiods and nutrient conditions

Controlled laboratory experiments were conducted to examine how photosynthesis and growth occur in Potamogeton wrightii Morong under different photoperiods and nutrient conditions. The experiment was based on a 3×2 factorial design with three photoperiods (16, 12 and 8 h) of 200 μE · m^?2·s^?1 irradiance and two nutrient conditions, high (90 μmol N · L^?1·d^?1 and 9 μmol P · L^?1·d^?1) and low (30 μmol N L^?1·d^?1 and 3 μmol P · L^?1·d^?1). After 14, 28, 56 and 70 days of growth, plants were harvested to determine net photosynthesis rate and various growth parameters. Above- and below-ground biomass were investigated on days 56 and 70 only. Plants under low nutrient conditions had greater leaf area, more chlorophyll a, a higher rate of net photosynthesis and accumulated more above- and below-ground biomass than plants in the high nutrient condition. Plants with an 8 h photoperiod in the low nutrient condition had a significantly higher rate of net photosynthesis, whereas 8 h photoperiod plants in the high nutrient condition had a lower rate of net photosynthesis and their photosynthetic capacity collapsed on day 70. We conclude that P. wrightii has the photosynthetic plasticity to overcome the effects of a shorter photoperiod under a tolerable nutrient state.     

Kinetics of the oxidation of endocrine disruptor nonylphenol by ferrate(VI)

The kinetics of the oxidation of endocrine disruptor nonylphenol (NP) by potassium ferrate(VI) (K₂FeO₄) in water as a function of pH 8.0–10.9 at 25°C is presented. The observed second-order rate constants, k _obs, decrease with an increase in pH 269–32 M^?1 s^?1. The speciation of Fe(VI) (HFeO ₄ ^? and FeO ₄ ^2? ) and NP (NP–OH and NP–O^?) species was used to explain the pH dependence of the k _obs values. At a dose of 10 mg L^?1 (50 μM) K₂FeO₄, the half-life for the removal of NP by Fe(VI), under water treatment conditions, is less than 1 min.     

Effect of waterborne boron and molybdenum on survival,growth and feed intake of Indian major carp,Cirrhinus mrigala (Hamilton)

The effect of either boron (B) or molybdenum (Mo) on survival, growth and feed intake of Indian major carp, Cirrhinus mrigala (Hamilton), advanced fry was studied in two separate experiments. Survival rates of C. mrigala fry (2.78±0.14 g) following 50 days’ exposure to B at 0.01 (control), 0.5, 1.0, 2.0, 4.0 and 8.0 mg·L ^?1 were 100% at all concentrations except 8.0 mg·L ^?1 where the survival rate 87.5±7.5%. We observed 100% survival of mrigala fry at all concentrations of Mo, 0.02 (control), 0.5, 1.0, 2.0, 4.0 and 8.0 mg·L ^?1. Both B and Mo at 0.5 mg·L ^?1 showed significantly (p<0.05) higher growth of the fish compared with control and other concentrations. B exposure at 1.0, 2.0 and 4.0 mg·L ^?1 had no significant effect on growth rate, whereas at 8.0 mg B·L ^?1 growth of the fish almost ceased. Mo exposure at 1.0, 2.0, 4.0 and 8.0 mg·L ^?1 caused no significant effect on growth rate of the fish compared to control. Both B and Mo at all concentrations had no significant effect on feed intake of the fish compared with control, except at the highest concentration of boron (8.0 mg·L ^?1).     

Efficient oxidation of bisphenol A with oxysulfur radicals generated by iron-catalyzed autoxidation of sulfite at circumneutral pH under UV irradiation

There is actually a need for efficient methods to clean waters and wastewaters from pollutants such as the bisphenol A endocrine disrupter. Advanced oxidation processes currently use persulfate or peroxymonosulfate to generate sulfate radicals. There are, however, few reports on the use of sulfite to generate sulfate radicals, instead of persulfate or peroxymonosulfate, except for dyes. Here we studied the degradation of the bisphenol A using iron(III) as catalyst and sulfite as precursor of oxysulfur radicals, at initial pH of 6, under UV irradiation at 395 nm. The occurrence of radicals was checked by quenching with tert-butyl alcohol and ethanol. Bisphenol A degradation products were analyzed by liquid chromatography coupled with mass spectrometry (LC–MS). Results reveal that iron(III) or iron(II) have a similar oxidation efficiency. Quenching experiments show that the oxidation rate of bisphenol A is 47.7 % for SO ₄ ^·? , 37.3 % for SO ₅ ^·? and 15 % for HO^·. Bisphenol A degradation products include catechol and quinone derivatives. Overall, our findings show that the photo-iron(III)–sulfite system is efficient for the oxidation of bisphenol A at circumneutral pH.     

Interlinked seasonal variation in biogenic nutrient fluxes and pore-water nutrient concentrations in intertidal sediments

The seasonal variation in biogenic fluxes of NH₄ ⁺, PO₄ ^3? and SiO₂ calculated from the nutrient excretion rates of dominant bivalves (Ruditapes philippinarum and Arcuatula [=Musculista] senhousia), and pore-water nutrient (NH₄ ⁺, PO₄ ^3?, SiO₂ and NO₃ ^? + NO₂ ^?), sedimentary acid-volatile sulfide (AVS) and benthic chlorophyll-a (Chl-a) concentrations was assessed on an intertidal sandflat in the Seto Inland Sea (Japan) from summer 1994 to autumn 1995. In spite of the large variability between sampling dates and stations, significant correlations between biogenic nutrient fluxes and pore-water nutrient concentrations were found, suggesting a seasonal linkage between bivalve-mediated biological processes and chemical features of sediments. This linkage was stronger in surface (0–0.5 cm) than subsurface (0.5–2 cm) sediments, consistent with the autoecological characteristics of R. philippinarum and A. senhousia inhabiting the uppermost sediment layer. Significant temporal variation in pore-water NO₃ ^? + NO₂ ^?, sedimentary AVS and benthic Chl-a concentrations was also found, which was related to both occasional extreme events (e.g., dystrophy) and alternating periods of production and decomposition. This study may serve twofold in (1) contributing to unravel the ecological structure and functioning of natural tidal flats, and the scale of seasonal variability in biotic and sedimentary parameters and (2) providing useful information for assessing the effectiveness of the physico-chemical and biological structure of artificial tidal flats which are growing in number and extension worldwide.     

Biodegradation of carbofuran in sequencing batch reactor augmented with immobilised Burkholderia cepacia PCL3 on corncob

The performance of sequencing batch reactors (SBRs) augmented with immobilised Burkholderia cepacia PCL3 on corncob for biodegradation of carbofuran in basal salt medium (BSM) was studied. A 2.0-L SBR with a working volume of 1.5 L was operated for a total cycle of 48 h, consisting of 1.0 h fill phase, 46 h react phase and 1.0 h decant phase. The initial pH of the feed medium was 7.0. Air was fed into the reactor at a controlled flow rate of 600 mL·min ^?1. The effect of hydraulic retention time (HRT) (14 to 6 days) on carbofuran-degradation efficiency was investigated at a carbofuran concentration in the feed medium of 20 mg·L ^?1. The shortest HRT resulting in complete degradation of carbofuran was 8 days. At 75% of the optimum HRT (6 days), the effects of biostimulation using organic amendments, i.e. molasses, cassava pulp, rice bran and spent yeast, and the effect of carbofuran concentration in the feed medium (20–80 mg·L ^?1) were investigated. The optimum conditions for SBRs were an initial carbofuran concentration of 40 mg·L ^?1 and 0.1 g·L ^?1 of rice bran as a biostimulated amendment. Complete degradation of carbofuran with a first-order kinetic constant (k ₁) of 0.044 h^?1 was achieved under these optimum conditions.     

Duckweed: an effective tool for phyto-remediation

Effective wastewater treatment through conventional methods that rely on heavy aeration are expensive to install and operate. Duckweed is capable of recovering or extracting nutrients or pollutants and is an excellent candidate for bio-remediation of wastewaters. Such plants grow very fast, utilizing wastewater nutrients and also yield cost effective protein-rich biomass as a by-product. Duckweeds being tiny surface-floating plants are easy to harvest and have an appreciable amount of protein (15%–45% dry mass basis) and a lower fiber (7%–14% dry mass basis) content. Besides nutrient extraction, duckweeds has been found to reduce total suspended solids, biochemical oxygen demand (BOD), and chemical oxygen demand in wastewater significantly. Depending on the initial concentrations of nutrients, duckweed-covered systems can remove nitrate (NO₃^?) at daily rates of 120–590 mg NO₃^? m^?2 (73%–97% of initial concentration) and phosphate (PO₄^?) at 14–74 mg PO₄^? m^?2 (63%–99% of initial concentration). Removal efficiencies within 3 days of 96% and 99% have been reported for BOD and ammonia (NH₃). Besides several genera of duckweeds (Spirodela, Lemna, Wolffia), other surface-floating aquatic plants like water hyacinth (Eichhornia) are well known for their phyto-remediation qualities.     

Ligand-less in situ surfactant-based solid phase extraction for preconcentration of silver from natural water samples prior to its determination by atomic absorption spectroscopy

A simple and rapid ligand-less in situ surfactant-based solid phase extraction method for preconcentration of silver from water samples is developed. In this method, a cationic surfactant containing a proper alkyl group (n-dodecyltrimethylammonium bromide) is dissolved in the aqueous sample and then a proper ion-pairing agent (ClO₄^?) is added. Due to the interaction between surfactant and ion-pairing agent, solid particles are formed and used for adsorption of silver carbonate. After centrifugation, the sediment is dissolved in 2.0 mL 1 M HNO₃ in ethanol and then aspirated directly into the flame atomic absorption spectrometer. Variables affecting the extraction efficiencies such as pH, concentrations of surfactant and CO₃^2?, ion pair concentration, and extraction time, are optimized. Under such conditions, the calibration curve is linear from 3 to 700 μg L^?1. Detection limit is 1.1 μg L^?1 with an enrichment factor of 37. The relative standard deviation for eight replicate measurements of 100 μg L^?1 is 2.1%. The method has been applied for the determination of silver in water samples.     

The pollution characteristics of PM<Subscript>2.5</Subscript> and correlation analysis with meteorological parameters in Xinxiang during the Shanghai Cooperation Organization Prime Ministers’ Meeting

The pollution characteristics of PM_2.5 and correlation analysis with meteorological parameters in Xinxiang during the Shanghai Cooperation Organization Prime Ministers’ Meeting were investigated. During the whole meeting, nine PM_2.5 samples were collected at a suburban site of Xinxiang, and the average concentration of PM_2.5 was 122.28 μg m^?3. NO₃ ^?, NH₄ ⁺, SO₄ ^2? accounted for 56.8% of the total water-soluble ions. In addition, with an exception of Cl^?, all of water-soluble ions decreased during the meeting. Total concentrations of crustal elements ranged from 6.53 to 185.86 μg m^?3, with an average concentration of 52.51 μg m^?3, which accounted for 82.5% of total elements. The concentrations of organic carbon and elemental carbon were 7.71 and 1.52 μg m^?3, respectively, lower than those before and after the meeting. It is indicated that during the meeting, limiting motor vehicles is to reduce exhaust emissions, delay heating is to reduce the fossil fuel combustion, and other measures are to reduce the concentration of PM_2.5. The directly dispersing by mixing layerheight increase and the indirectly reducing the formation of secondary aerosol by low relative humidity, andthese are the only two key removing mechanisms of PM_2.5 in Xinxiang during the meeting.