A laboratory pilot study of thermal decontamination of soils polluted by PCBs. Comparison with thermogravimetric analysis

Real soils contaminated with a mixture of polychlorinated biphenyls were thermally decontaminated in a laboratory scale thermal desorption apparatus, under different operating conditions including two operating pressures (P= 0.01 and 0.1 MPa), different sample masses (80-320 g), carrier gas flow rates (0-30-280 Nl h(-1)) and two initial contamination levels. A standard European soil artificially contaminated with 4-chlorobiphenyl was decontaminated using a thermogravimetric analyser (TGA). The same parametric study as cited earlier was performed. With both techniques, the extent of decontamination was studied as a function of temperature during the heating programs (2-3 degrees C min(-1) for the thermal desorption apparatus; 5 degrees C min(-1) for TGA). Only a few differences were noticed between the two techniques. The decontamination starts when the melting temperature of the contaminant is reached (30 degrees C) and is complete before 350 degrees C. Thermogravimetric analysis which does not necessitate any chemical analysis appears to be a very attractive technique to investigate the feasibility of a decontamination and to quickly determine the best operating conditions.     

New method for producing carbon foam from recycled carbon (NEWCAFO)

Journal of Material Cycles and Waste Management - The aim of the study was to define a new method (SENAY process) for carbon foam (CF) production following curing by mixing organic materials with...     

A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

烟气脱硫工艺方案的模糊决策分析法

以燃煤电厂烟气脱硫方案的技术评价为研究对象,提出了将软科学研究人员与领域专家、定性分析与定量分析、经验决策与计算机辅助决策融为一体的模糊决策分析法。并在此基础上建立了烟气脱硫方案技术评价的物理模型、数学模型和判断准则等,结合对W电厂烟气脱硫工艺的选择,进行了实例分析和应用。     

Implementation of the semi-aerobic landfill system (Fukuoka method) in developing countries: a Malaysia cost analysis

Most of the existing solid waste landfill sites in developing countries are practicing either open dumping or controlled dumping. Proper sanitary landfill concepts are not fully implemented due to technological and financial constraints. Implementation of a fully engineered sanitary landfill is necessary and a more economically feasible landfill design is crucial, particularly for developing countries. This study was carried out by focusing on the economics from the development of a new landfill site within a natural clay area with no cost of synthetic liner up to 10 years after its closure by using the Fukuoka method semi-aerobic landfill system. The findings of the study show that for the development of a 15-ha landfill site in Malaysia with an estimated volume of 2,000,000 m(3), the capital investment required was about US 1,312,895 dollars, or about US 0.84 dollars/tonne of waste. Assuming that the lifespan of the landfill is 20 years, the total cost of operation was about US 11,132,536 dollars or US 7.15 dollars/tonne of waste. The closure cost of the landfill was estimated to be US 1,385,526 dollars or US 0.89 dollars/tonne of waste. Therefore, the total cost required to dispose of a tonne of waste at the semi-aerobic landfill was estimated to be US 8.89 dollars. By considering an average tipping fee of about US 7.89 dollars/tonne of waste in Malaysia in the first year, and an annual increase of 3% to about US 13.84 dollars in year-20, the overall system recorded a positive revenue of US 1,734,749 dollars. This is important information for the effort of privatisation of landfill sites in Malaysia, as well as in other developing countries, in order to secure efficient and effective landfill development and management.     

A novel method for preparing phosphorus building gypsum (PBG)-based building materials with low water/gypsum ratios

Journal of Material Cycles and Waste Management - It is necessary to consider the dual problems of poor performance and low production efficiency that stem from the highly utilised water/gypsum...     

New characterisation method of electrical and electronic equipment wastes (WEEE)

Innovative separation and beneficiation techniques of various materials encountered in electrical and electronic equipment wastes (WEEE) is a major improvement for its recycling. Mechanical separation-oriented characterisation of WEEE was conducted in an attempt to evaluate the amenability of mechanical separation processes. Properties such as liberation degree of fractions (plastics, metals ferrous and non-ferrous), which are essential for mechanical separation, are analysed by means of a grain counting approach. Two different samples from different recycling industries were characterised in this work. The first sample is a heterogeneous material containing different types of plastics, metals (ferrous and non-ferrous), printed circuit board (PCB), rubber and wood. The second sample contains a mixture of mainly plastics. It is found for the first sample that all aluminium particles are free (100%) in all investigated size fractions. Between 92% and 95% of plastics are present as free particles; however, 67% in average of ferromagnetic particles are liberated. It can be observed that only 42% of ferromagnetic particles are free in the size fraction larger than 20 mm. Particle shapes were also quantified manually particle by particle. The results show that the particle shapes as a result of shredding, turn out to be heterogeneous, thereby complicating mechanical separation processes. In addition, the separability of various materials was ascertained by a sink–float analysis and eddy current separation. The second sample was separated by automatic sensor sorting in four different products: ABS, PC–ABS, PS and rest product. The fractions were characterised by using the methodology described in this paper. The results show that the grade and liberation degree of the plastic products ABS, PC–ABS and PS are close to 100%. Sink–float separation and infrared plastic identification equipment confirms the high plastic quality. On the basis of these findings, a global separation flow sheet is proposed to improve the plastic separation of WEEE.     

Comprehensive analysis on mercury stream of cold cathode fluorescent lamps (CCFLs) in Korea (Republic of)

Journal of Material Cycles and Waste Management - Due to the activation of the Minamata Convention, policies and treatment facilities for the safe management of mercury and mercury compounds have...     

Influence of poly(bisphenol A carbonate) and poly(ethylene terephthalate) on poly(vinyl chloride) dehydrochlorination

Recycling of poly(vinyl chloride) (PVC) waste is a serious problem because of its high chlorine content. Dehydrochlorination of PVC-containing polymer waste produces solid residue char, for which conversion to pyrolysis oil in a petrochemical plant seems to be an attractive way of recycling PVC waste. Unfortunately, some polymer admixtures react with HCl and cause formation of chloroorganic compounds in a char. This article describes the influence of polycarbonates and poly(ethylene terephthalate) on thermal feedstock recycling of PVC wastes using a two-stage method. It was found that the presence of polycarbonate causes the formation of small amounts of benzyl chloride and other chloroaryl or chloroalkylaryl compounds. Poly(ethylene terephthalate) interacts with HCl forming significant amounts of various chlorocompounds – mainly chloroethyl esters of terephthalic and benzoic acids, but derivatives possessing chlorine directly connected to the aromatic ring are also formed.     

A Novel Biodegradable Green Poly(l-Aspartic Acid-Citric Acid) Copolymer for Antimicrobial Applications

Poly (l-aspartic acid-citric acid) green copolymers were developed using thermal polymerization of aspartic acid (ASP) and citric acid (CA) followed by direct bulk melt condensation technique. Antibacterial properties of copolymer of aspartic acid based were investigated as a function of citric acid content. This study is focused on the microorganism inhibition performance of aspartic acid based copolymers. Results showed that inhibition properties increase with increasing citric acid content. Characterization of obtained copolymers was carried out with the help of infrared absorption spectra (FTIR), x-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermo gravimetric analysis (TGA). The antibacterial activity of copolymers against bacteria like E-coli, Bacillus and pseudomonas was investigated. The copolymers showed excellent antimicrobial activities against three types of microorganisms. Overall studies indicated that the above copolymers possess a broad wound dressing activity against above three types of bacteria and may be useful as antibacterial agents.     

Precision determination for the dynamic respirometric index (DRI) method used for biological stability evaluation on municipal solid waste and derived products

Dynamic respiration index (DRI) is an effective respirometric method to measure the biological stability of municipal solid waste (MSW). It allows testing MSW biological stability under standardized conditions and is now used as a routine analytical method. However, the method needs to be studied for precision parameters to ensure the quality of results generated.This work reports on a DRI validation study, detecting repeatability (r) and reproducibility limits (R). To perform the study, 4-6 Italian laboratories took part in an interlaboratory test for the validation of the DRI method on four different municipal solid wastes from different mechanical-biological treatment full-scale plants. Precision values (r and R) of DRI, expressed as relative standard deviation, were in the range of 3.6% and 15.5%, and were acceptable when compared with previous data obtained in another respirometric test. On the other hand, no regressions were found between r and R, and DRI, and as a consequence prediction of precision values was not possible a priori for different DRI levels, unless the same typology of waste was considered.     

Longitudinal data analysis in support of functional stability concepts for leachate management at closed municipal landfills

Landfill functional stability provides a target that supports no environmental threat at the relevant point of exposure in the absence of active control systems. With respect to leachate management, this study investigates “gateway” indicators for functional stability in terms of the predictability of leachate characteristics, and thus potential threat to water quality posed by leachate emissions. Historical studies conducted on changes in municipal solid waste (MSW) leachate concentrations over time (longitudinal analysis) have concentrated on indicator compounds, primarily chemical oxygen demand (COD) and biochemical oxygen demand (BOD). However, validation of these studies using an expanded database and larger constituent sets has not been performed. This study evaluated leachate data using a mixed-effects regression model to determine the extent to which leachate constituent degradation can be predicted based on waste age or operational practices. The final dataset analyzed consisted of a total of 1402 samples from 101 MSW landfills. Results from the study indicated that all leachate constituents exhibit a decreasing trend with time in the post-closure period, with 16 of the 25 target analytes and aggregate classes exhibiting a statistically significant trend consistent with well-studied indicators such as BOD. Decreasing trends in BOD concentration after landfill closure can thus be considered representative of trends for many leachate constituents of concern.     

A new method for evaluating the sewage sludge pyrolysis kinetics

A new method to simplify calculation the kinetics model is applied to sewage sludge pyrolysis based on the assumption that volatile run out as soon as it formed and during temperature arising process in this study. Difference method widely used to solve math problems is conducted to calculate kinetics parameters. Pyrolysis experiments are carried out at heating rates of 10, 15, 20, and 50 °C/min. All the TG curves are divided into three parts which are beginning decomposition temperature range, main decomposition temperature range, and final decomposition temperature range. The second one is employed to determine the parameters for more than 70% of the total mass loss occurs in this range. According to the developed method, the react order, reaction energy and pre-exponential factor are obtained, which are in the range of 3.9–4.1, 82.3–109.2 kJ/mol and 7.7 × 10⁶–2.8 × 10⁹/min, respectively, which are in the range of that reported previously. As a comparison experimental data with calculated data, the well fitting results indicate that this method is appropriate for simulating sludge pyrolysis kinetics.     

A carbon-13 method for evaluating degradation of starch-based polymers

A new method for evaluating biodegradability of starch-based and certain other polymer blends uses the pre- and postexposure stable carbon isotope composition of material coupled with weight loss data to determine which components have degraded. The naturally occurring stable isotope of carbon.¹³C, is enriched in corn starch (¹³C, approx. –11) compared to petroleum-derived synthetic polymers (¹³C, approx. –32). Results on starch-synthetic polymer blends indicate that the ¹³C signatures of these blends are near-linear mixtures of their component ¹³C. Values of a ¹³C for starch-synthetic polymer blends exposed to biologically active laboratory soil and artificial seawater conditions are depleted in¹³C compared to unexposed samples, suggesting loss of the starch component. Combined with weight loss data for the exposed samples, the ¹³C values are statistically consistent with models requiring loss of the soluble component glycerin, followed by loss of starch, then petrochemical polymer, or simultaneous loss of starch and petrochemical polymer. Replicate ¹³C analyses of starch-synthetic polymer blends increase the statistical power of this relatively inexpensive, accessible technique to discriminate between degrading components.     

The Potential of Cleaner Fermentation Processes for Bioplastic Production: A Narrative Review of Polyhydroxyalkanoates (PHA) and Polylactic Acid (PLA)

Journal of Polymers and the Environment - Synthetic plastics generate major problems in landfills after their consumption for occupying high volumes and difficult the decomposition of other organic...     

A method for livestock waste management planning in NE Spain

A method of decision-making on livestock wastes management in areas with nutrient surplus due to high livestock density is applied in Catalonia (NE Spain). Nutrient balance is made considering soil nitrogen application as the limiting factor. Special attention is paid to the centralized treatment option. The method presented consists of: 1. minimizing livestock waste generation (at farm scale) as a step previous to any other, both in amount and limiting components, 2. applying the nitrogen balance method at regional and municipal scale and providing enough storage capacity in order to apply wastes in an agronomically correct way, 3. spatially refining the results of the nitrogen balance by a proposed method that allows precisely pinpointing the hotspots of livestock waste generation, where centralized treatment might be an interesting option, and 4. deciding on the waste treatment objectives, provided that treatments be necessary. Knowledge about the wastes, meeting the interests and merging the efforts of the various actors, as well as an adequate budget are necessary ingredients for the success of any waste management plan.     

灰色摆动序列的GM（1,1）拟合建模法及其应用

建立了灰色摆动序列ＧＭ（１,１）动态指数变换拟合建模方法,对某地工业固体废物产生量的预测结果表明,该法合理有效,切实可行,并有良好的精度。     

Recycling and recovery routes for incinerated sewage sludge ash (ISSA): A review

The drivers for increasing incineration of sewage sludge and the characteristics of the resulting incinerated sewage sludge ash (ISSA) are reviewed. It is estimated that approximately 1.7 million tonnes of ISSA are produced annually world-wide and is likely to increase in the future. Although most ISSA is currently landfilled, various options have been investigated that allow recycling and beneficial resource recovery. These include the use of ISSA as a substitute for clay in sintered bricks, tiles and pavers, and as a raw material for the manufacture of lightweight aggregate. ISSA has also been used to form high density glass–ceramics. Significant research has investigated the potential use of ISSA in blended cements for use in mortars and concrete, and as a raw material for the production of Portland cement. However, all these applications represent a loss of the valuable phosphate content in ISSA, which is typically comparable to that of a low grade phosphate ore. ISSA has significant potential to be used as a secondary source of phosphate for the production of fertilisers and phosphoric acid. Resource efficient approaches to recycling will increasingly require phosphate recovery from ISSA, with the remaining residual fraction also considered a useful material, and therefore further research is required in this area.     

Stratigraphic flux—A method for determining preferential pathways for complex sites

Experience with groundwater remediation over several decades has demonstrated that successful outcomes depend on quantitative conceptual site models (CSMs). Over the last 30 years, we have progressed from groundwater pump‐and‐treat remedies, which were largely designed based on a water supply perspective, to in situ and combined remedy strategies, which are only beginning to benefit from understanding the aquifer architecture and distribution of contaminant mass to assess plume maturity, mass flux, and more reliable means of fate and transport assessment. The U.S. Air Force funded the development of the Stratigraphic Flux approach to provide a framework for understanding contaminant transport pathways at its complex sites and enable more reliable and cost‐effective remediation. Stratigraphic Flux enables the development of quantitative, flux‐based CSMs that are founded in sequence stratigraphy, and high‐resolution hydraulic conductivity and contaminant distribution measurements. The result is a three‐dimensional graphical mapping of relative contaminant flux and classification of transport potential that is easy for all stakeholders to understand. The Stratigraphic Flux graphical model is based on a hydrofacies classification system that describes transport potential in three segments of the aquifer: transport zones—where the majority of groundwater flow occurs and transport rates are measured in feet per day; slow advection zones—where transport rates are measured in feet per year; and storage zones—where typically less than 1% of flow occurs, and diffusion dominates contaminant transport. The hydrofacies architectures are based on stratigraphy and transport potential is defined by grouping facies by orders of magnitude classes in hydraulic conductivity. By combining the hydrofacies architecture with contaminant concentration distributions, one can map relative contaminant flux to define and target the complex pathways that control contaminant transport and cleanup behavior. In this article, we describe the Stratigraphic Flux framework, focusing on the key information needed and the methods of analysis. We illustrate the results of its application to evaluate migration pathways for trichlorethylene and chromium at a former chrome pit at Air Force Plant 4 in Fort Worth, Texas. A comprehensive guidance document that describes the approach with a broad spectrum of tools and several site examples can be requested from the authors.     

A Literature Review of Poly(Lactic Acid)

A literature review is presented regarding the synthesis, and physicochemical, chemical, and mechanical properties of poly(lactic acid)(PLA). Poly(lactic acid) exists as a polymeric helix, with an orthorhombic unit cell. The tensile properties of PLA can vary widely, depending on whether or not it is annealed or oriented or what its degree of crystallinity is. Also discussed are the effects of processing on PLA. Crystallization and crystallization kinetics of PLA are also investigated. Solution and melt rheology of PLA is also discussed. Four different power-law equations and 14 different Mark–Houwink equations are presented for PLA. Nuclear magnetic resonance, UV–VIS, and FTIR spectroscopy of PLA are briefly discussed. Finally, research conducted on starch–PLA composites is introduced.