A systematic approach to in situ bioremediation in groundwater

In situ bioremediation (ISB) melds an understanding of microbiology, chemistry, hydrogeology, and engineering into a strategy for planned and controlled microbial degradation of specific contaminants. ISB creates subsurface environmental conditions, typically through reduction oxidation manipulation, which induce the degradation of contaminants via microbial catalyzed biochemical reactions. In turn, the microbes produce enzymes that are utilized to derive energy and that are instrumental in the degradation of target chemicals. To accomplish this chain of events, the type of microorganisms, contaminant, and the geological conditions at the site must be considered. Since in situ conditions are manipulated by engineered means, the most important consideration is the ability to transmit and mix liquids in the subsurface. The Interstate Technology Regulatory Council (ITRC)–ISB Team has recently completed a guidance document that describes a systematic approach to ISB in groundwater. ITRC is a state‐led coalition of more than 40 states working together with industry and stakeholders to achieve regulatory acceptance of environmental technologies. © 2003 Wiley Periodicals, Inc.     

Digestion of waste bananas to generate energy in Australia

This paper presents results from laboratory studies to measure the methane yield and rate of digestion of reject bananas. These parameters were determined in experiments that took into account the likely configuration of a full-scale plant in the banana growing region of north Queensland. The digestion was conducted in a 200-l reactor using fed-batch operation, relying entirely on the natural microbial consortia on the reject bananas to avoid reliance on external inocula such as sludge, an undesirable material around food packaging facilities. An enrichment culture was first established in a highly buffered 200-l batch digestion unit. The fed-batch digester was then started by exchanging leachate with the mature batch reactor. Under loading conditions of 0.6 kg VS m(-3)d(-1) over 70 days where the average working volume was 160 l, the digester produced 398+/-20 l CH4 kg VS(-1). Increasing the loading rate to 1.6 kg VS m(-3)d(-1) resulted in a reduced methane yield of 210 l CH4 kg VS(-1) over 23 days of operation, with a concomitant accumulation of banana waste in the digester. The leachate at the end of digestion contained over 4000 mg l(-1)K, 200 mg l(-1) N and 75 mg l(-1), levels that exceed acceptable limits for general agricultural irrigation.     

Improvements to TCE Microcosm Protocols for Biostimulation in Bedrock Aquifers

In this study, a factorial‐designed experiment of biostimulated trichloroethene (TCE) dechlorination in fractured bedrock aquifers using microcosms evaluated several potential biostimulants (i.e., nutrients, vitamins, and sterile groundwater). Substantial cost savings and resource efficiency can be provided by this approach because: factorial designs require relatively few microcosms per factor; the interpretation of the observations can proceed largely by common sense, simple arithmetic, and computer graphics; the observations can indicate promising directions for further experimentation and causative relationships; and designs can be suitably augmented when a more in‐depth exploration is needed. TCE degradation was evaluated using three methods of data analysis: (1) analysis of covariance (ANCOVA) between biotic and abiotic treatment trend‐line slopes; (2) calculation of biodegradation half‐life; and (3) effects screening by model fitting. Microcosm preparation with crushed rock in groundwater was found to more closely match the previously observed field rates than the preparation with only groundwater. Injection of nutrient and vitamin mixtures was made into microcosms that were previously aged to obtain consistent conditions, and the TCE concentration measured after incubating for 45 days. Comparison of results indicated that the nutrient mixture slows or inhibits the degradation of TCE compared to the sterile groundwater; however, the vitamin mixture offsets and nearly compensates for the inhibitory effect of the nutrient mixture. It is recommended that this factorial experiment be augmented with additional studies of individual or groups of compounds from the vitamin mixture using this methodology to isolate and identify the specific factor or interaction responsible for the inhibitory compensation. © 2013 Wiley Periodicals, Inc.     

Characterization of Dust Storms to Hong Kong in April 1998

In April 1998, two intense dust storms were generated in CentralAsia and transported eastward across East Asia (15 and 19 April). This article presents the chemical characterization ofHong Kong (HK) aerosols during the dust storms. During the 15 Aprildust storm, hourly respiratory suspended particles (RSP)(particle diameter smaller than 10 m) concentrationsmonitored at 7 sites in Hong Kong reached the peak valuessynchronously between 9 and 11 a.m. on 17 April, in which thehighest concentration was 267 g m^-3. Analysis ofthe RSP samples showed that concentrations of crustalelements (Ba, Ca, Cd, Cr, Fe, Mg, K⁺) and anthropogenicspecies (As, Ni, Pb, Zn, NH₄ ⁺, NO₃ ^-,SO₄ ^2- and total carbon) were substantiallyenhanced. Enhancement of these species was more than afactor of 2 to 14 relative to the non dust period. The totalcarbon content was high, at 59 g m^-3 (notincluding carbonate), and the enrichment factors of Asand Pb on 17 April were 122 and 117, respectively. Thisimplied that anthropogenic materials together with mineraldust were transported to HK from Mainland China. Based onmaterial balance calculations, mineral dust contributed41% to the observed RSP mass on 17 April, which was 2 times thatof the nondust sample (22%). From the 5-day backwardtrajectory analysis, this storm was transported directlyfrom Northwest China to HK. However, there was nocorresponding observation for the 19 April dust stormaerosol. Consequently, 15 April storm had stronger impact onHK's atmosphere than 19 April storm. Compared to the HK AirQuality Objective, 15 April dust storm did not cause seriousair pollution in HK.     

Waste foundry sand used to cover organic waste in landfills

Journal of Material Cycles and Waste Management - Waste foundry sand (WFS) is a waste generated during the molding of metal parts and primarily discarded in landfills, which generates environmental...     

Dynamics of Ammonia Exchange in Response to Cutting and Fertilising in an Intensively-Managed Grassland

Continuous micrometorological measurements of ammonia (NH₃)exchange were made for a period of 19 months (May 1998–November 1999) over intensively managed grassland in southern Scotland. This study focused on the influence of management activities, such as cutting and fertilising, on vegetation-atmosphere exchange of NH₃. Measurements were conducted within the European project GRAMINAE (GRassland AMmonia INteractions Across Europe) within which the Scottish site forms one of 6 sites in an E–W transect across Europe. NH₃ emissions were enhanced (up to 300 ng m^-2 s^-1) after cutting followed by larger emissions after fertilising (up to 1400 ng m^-2 s^-1). Annual budget calculations show the intensive grassland acted as a net source (1.8 kg N ha^-1 yr¹) although fluxes were bi-directional with deposition dominating in the winter and emission in the summer. Initial modelling of the NH₃ exchange using a `canopy compensation point' model has been conducted for key periods. The dynamics of the fluxes during these key periods, such as before and after cutting and fertilising, may be reproduced by introducing different values of the apoplastic ratio, = [NH₄ ⁺]/[H⁺].     

Accessibility of starch to enzymatic degradation in injection-molded starch-plastic composites

Most of the starch in starch-polyethylene-co-acrylic acid (EAA)-polyethylene (PE) composites prepared by injection molding was not accessible to starch-hydrolyzing enzymes. Even when these composites were treated with enzyme in the presence of Triton X-100 for 96 h, little starch hydrolysis was observed. However, when the starch-plastic material was pulverized, both the extent and the rate of starch hydrolysis increased dramatically, with about 70% hydrolysis of the starch within 18 h. Reactions carried out for up to 96 h showed that, while the enzyme was active, the reaction reached a plateau, achieving a total of 80% starch hydrolysis. Fourier transform infrared (FTIR) spectroscopy revealed that only starch, and not EAA or PE, was affected by enzyme in pulverized samples. Results indicated that while 80% of the starch in these composites was transiently inaccessible, perhaps due to EAA and PE forming an impermeable barrier to the enzyme, the other 20% remained inaccessible to enzymes. Also, the rate of starch digestion as determined by solubilized reducing sugar correlated with the particle size of the pulverized material, suggesting that a large available surface area is critical for rapid starch degradation in such composites.The mention of firms names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over the firms or similar products not mentioned. All programs and services of the U.S. Department of Agriculture are offered on a nondiscriminatory basis without regard to race, color, national origin, religion, sex, marital status, or handicap.     

From dumping to sanitary landfills--solid waste management in Israel

To address the problem of solid waste in Israel, the Ministry of the Environment has formulated a policy based on integrated waste management. The policy calls for reduction of waste at source, reuse, recycling (including composting), waste-to-energy technologies, and landfilling. Due to the implementation of this policy, all the large dumps were closed, state-of-the art landfills were built, and recovery rates have increased from 3% in the beginning of the 1990s to almost 20% in 2003. More than 95% of the municipal solid waste is disposed and treated in an environmentally sound manner - in comparison to a mere 10% just a decade ago. The policy was implemented utilizing both enforcement and financial support ("stick and carrot" approach).     

Bioconversion of lawn waste amended with kitchen waste and buffalo dung in to value-added vermicompost using Eisenia foetida to alleviate landfill burden

Journal of Material Cycles and Waste Management - Enormous quantities of waste such as lawn waste (LW) and kitchen waste (KW) are generated in urban institutes, proper management of which is...     

A methodology to determine gaseous emissions in a composting plant

Environmental impacts associated to different waste treatments are of interest in the decision-making process at local, regional and international level. However, all the environmental burdens of an organic waste biological treatment are not always considered. Real data on gaseous emissions released from full-scale composting plants are difficult to obtain. These emissions are related to the composting technology and waste characteristics and therefore, an exhaustive sampling campaign is necessary to obtain representative and reliable data of a single plant. This work proposes a methodology to systematically determine gaseous emissions of a composting plant and presents the results obtained in the application of this methodology to a plant treating source-separated organic fraction of municipal solid waste (OFMSW) for the determination of ammonia and total volatile organic compounds (VOC). Emission factors from the biological treatment process obtained for ammonia and VOC were 3.9 kg Mg OFMSW⁻¹ and 0.206 kg Mg OFMSW⁻¹ respectively. Emissions associated to energy use and production were also quantified (60.5 kg CO₂ Mg OFMSW⁻¹ and 0.66 kg VOC Mg OFMSW⁻¹). Other relevant parameters such as energy and water consumption and amount of rejected waste were also determined. A new functional unit is presented to relate emission factors to the biodegradation efficiency of the composting process and consists in the reduction of the Respiration Index of the treated material. Using this new functional unit, the atmospheric emissions released from a composting plant are directly related to the plant specific efficiency.     

LCA to Evaluate the Environmental Impact for Chemical Pre-treatment in Plastics Metallization

The life cycle assessment methodology was used to calculate the environmental impacts of the current chemical pre-treatment with chromium(VI) for electroplating acrylonitrile butadiene styrene. The inventory comprised: the procurement of chemicals; the manufacturing process with successive baths and rinses that requires, in addition to chemicals, energy to heat baths, air agitation, filtration, and so forth, wastewater treatment and air emissions; and also the treatment of sludges from wastewater treatment and exhausted baths. Chromic acid was almost the unique responsible of eco-toxicity (97.5 %) and human toxicity-cancer (99.8 %) and it was one of the highest contributor to climate change, cumulative energy demand, fossil fuel depletion, human toxicity non-cancer, and in abiotic depletion.     

Ozone Deposition to a Coniferous and Deciduous Forest in the Czech Republic

Estimates of ozone concentration and deposition flux to coniferous and deciduous forest in the Czech Republic on a 1 × 1 km grid during growing season (April–September) of the year 2001 are presented. Ozone deposition flux was derived from ozone concentrations in the atmosphere and from its deposition velocities. To quantify the spatial pattern in surface concentrations at 1 km resolution incorporating topography, empirical methods are used. The procedure maps ozone concentrations from the period of the day when measurements are representative for the forest areas of countryside. The effects of boundary layer stability are quantified using the observed relationship between the diurnal variability of surface ozone concentration and altitude. Ozone deposition velocities were calculated according to a multiple resistance model incorporating aerodynamic resistance (R _a ), laminar layer resistance (R _b ) and surface resistance (R _c ). Surface resistance (R _c ) comprises stomatal resistance (R _sto ). R _sto was calculated with respect to global radiation, surface air temperature and land cover. Modelled total and stomatal ozone fluxes are compared with the maps describing equivalent values of AOT40 (accumulated exposure over threshold of 40 ppb). For forests, the critical level (9,000 ppbh May–July daylight hours) is exceeded over 50% of forested territory. This indicates the potential for effects on large areas of forest. There is significiant correspondence between the exposure index AOT40 and the total ozone flux, but the relation between the total ozone flux and AOT40 exposure index is not clear in all parts of the forest territory.     

A mathematical model to predict the composition and generation of hospital wastes in Iran

The aim of this study is to investigate the quality and quantity of hospital wastes in Iran. The generated hospital wastes have been estimated by the number of hospitals and the number of active beds in each province of Iran in 2001. All data and information have been gathered from: (i) Iran Statistics Center, (ii) literature review, and (iii) hospital waste investigations for an average hospital. Physical analyses have been conducted in terms of various materials (plastic, textile, paper, metal, and others) and components (biological, infectious, medical, and regular wastes). Based on the above-mentioned investigation and information, a mathematical model has been developed to calculate the generation of (infectious) hospital wastes for any desired year. Utilizing the model, generated infectious hospital wastes has been estimated as 698,937 tones for 2008 (short-term) and 3,494,387 tones for 2028 (long-term period). If the real infectious wastes are collected separately, then the generated infectious wastes will be reduced by 15.1% of the above-mentioned amount (139,787 tones for 2008, and 698,877 tones for 2028). Results of physical analysis show the components of the hospital waste as: (a) infectious, 67.3%; (b) medical, 8.8%; (c) biological, 1.8%; and (d) common municipal wastes, 22.1%. An appropriate collection method requires training the staff at hospitals along with preparation of the required facilities. Of course, both of these requirements are cost intensive.     

Solar‐powered in situ soil washing with surfactant to collect LNAPL

This article presents the findings of a sustainable, surfactant‐enhanced, product recovery pilot‐scale study (PSS) completed between January 2010 and May 2010 at the Hydrocarbon Burn Facility located at the John F. Kennedy Space Center in Florida. The goal of this study was to implement a unique, simple, and sustainable light nonaqueous‐phase liquid (LNAPL) recovery process and evaluate site‐specific volumes and rates of LNAPL that could be collected and the degree of soil and groundwater cleanup that could be achieved. The recovery process was a combination of groundwater recirculation at a rate of approximately 2.9 gallons per minute (11.0 liters per minute), soil washing via LNAPL mobilization, and collection of LNAPL via a hydrophobic LNAPL skimmer. A biodegradable surfactant, ECOSURF^TM SA‐15, was added to the recirculation line to lower the interfacial tension and facilitate LNAPL recovery via mobilization. All equipment (submersible pump, LNAPL skimmer, surfactant feed pump, controls, and various other equipment) used was powered by a solar panel array. Approximately 60 gallons (227 liters) or 429 pounds (195 kilograms) of LNAPL were collected at the recirculation site over approximately three months during the PSS. The data suggest that surfactant amendments greatly enhanced free product collection. The maximum rate of free product collection was approximately 1 gallon (3.8 liters) per day. © 2012 Wiley Periodicals, Inc.     

The Use of a GIS-based Inventory to Provide a Regional Risk Assessment of Standing Waters in Great Britain Sensitive to Acidification from Atmospheric Deposition

Previous attempts to identify regions of Britain vulnerable to acidification have used sensitivity maps based on the distributionof soils, geology, and land cover across Great Britain. Additionally, a systematic survey of freshwaters undertaken as partof the U.K. critical loads mapping programme provides a regional assessment of both sensitivity (critical loads) and, in tandem withdeposition data, potential impact (critical load exceedance). Both approaches, while useful for identifying regional patterns, do not enable estimates of the number of affected water bodies to be made. Recent EU legislation (e.g., The Water Framework Directive) requires member states to set water quality objectives for all water bodies. We developed a GIS-based inventory of standing water bodies in response to the need for legislation-driven assessments of the status of the U.K. lake population. This paper describes how the inventory can be used to assess the number of standing water bodies in Britain that are vulnerable to acid deposition (at current levels), building on the sensitivity mapping undertaken previously. Using this approach, approximately 31% of all standing waters in Great Britain (excluding the Shetlands and Orkney) larger than 0.02 ha are identified as `at risk' from acidification. Higher proportions are vulnerable in Scotland and Wales. Additionally, large numbers of standing waters in areas designated for environmental protection purposes are also vulnerable.     

Comparisons of Measured and Modelled Ozone Deposition to Forests in Northern Europe

The performance of a new dry deposition module, developedfor the European-scale mapping and modelling of ozone flux to vegetation, was tested against micrometeorological ozone and water vapour flux measurements. The measurement data are for twoconiferous (Scots pine in Finland, Norway spruce in Denmark) and one deciduous forest (mountain birch in Finland). On average, themodel performs well for the Scots pine forest, if local inputdata are used. The daytime deposition rates are somewhat over-predicted at the Danish site, especially in the afternoon. The mountain birch data indicate that the generic parameterisationof stomatal responses is not very representative of this northernspecies. The module was also tested by using modelled meteorological data that constitute the input for a photochemical transport model.     

Use of waste gypsum to replace natural gypsum as set retarders in portland cement

The present study is focused on clarifying the influence of waste gypsum (WG) in replacing natural gypsum (NG) in the production of ordinary Portland cement (OPC). WG taken from slip casting moulds in a ceramic factory was formed from the hydration of plaster of paris. Clinker and 3–5 wt% of WG was ground in a laboratory ball mill to produce cement waste gypsum (CMWG). The same procedure was repeated with NG to substitute WG to prepare cement natural gypsum (CMNG). The properties of NG and WG were investigated via X-ray Diffraction (XRD), X-ray fluorescence (XRF) and differential scanning calorimetry (DSC)/thermogravimetric (TG) to evaluate the properties of CMNG and CMWG. The mechanical properties of cement were tested in terms of setting time, flexural and compressive strength. The XRD result of NG revealed the presence of dihydrate while WG contained dihydrate and hemihydrate. The content of dihydrate and hemihydrates were obtained via DSC/TG, and the results showed that WG and NG contained 12.45% and 1.61% of hemihydrate, respectively. Furthermore, CMWG was found to set faster than CMNG, an average of 15.29% and 13.67% faster for the initial and final setting times, respectively. This was due to the presence of hemihydrate in WG. However, the values obtained for flexural and compressive strength were relatively the same for CMNG and CMWG. Therefore, this result provides evidence that WG can be used as an alternative material to NG in the production of OPC.     

Targeted intervention strategies to optimise diversion of BMW in the Dublin, Ireland region

Urgent transformation is required in Ireland to divert biodegradable municipal waste (BMW) from landfill and prevent increases in overall waste generation. When BMW is optimally managed, it becomes a resource with value instead of an unwanted by-product requiring disposal. An analysis of survey responses from commercial and residential sectors for the Dublin region in previous research by the authors proved that attitudes towards and behaviour regarding municipal solid waste is spatially variable. This finding indicates that targeted intervention strategies designed for specific geographic areas should lead to improved diversion rates of BMW from landfill, a requirement of the Landfill Directive 1999/31/EC. In the research described in this paper, survey responses and GIS model predictions from previous research were the basis for goal setting, after which logic modelling and behavioural research were employed to develop site-specific waste management intervention strategies. The main strategies devised include (a) roll out of the Brown Bin (Organics) Collection and Community Workshops in Dún Laoghaire Rathdown, (b) initiation of a Community Composting Project in Dublin City (c) implementation of a Waste Promotion and Motivation Scheme in South Dublin (d) development and distribution of a Waste Booklet to promote waste reduction activities in Fingal (e) region wide distribution of a Waste Booklet to the commercial sector and (f) Greening Irish Pubs Initiative. Each of these strategies was devised after interviews with both the residential and commercial sectors to help make optimal waste management the norm for both sectors. Strategy (b), (e) and (f) are detailed in this paper. By integrating a human element into accepted waste management approaches, these strategies will make optimal waste behaviour easier to achieve. Ultimately this will help divert waste from landfill and improve waste management practice as a whole for the region. This method of devising targeted intervention strategies can be adapted for many other regions.     

Carbon speciation in municipal solid waste incinerator (MSWI) bottom ash in relation to facilitated metal leaching

The release of inorganic and organic contaminants from municipal solid waste incinerator (MSWI) bottom ash is controlled to a large extent by the release of dissolved organic carbon (DOC), and in particular by the reactive humic (HA) and fulvic acids (FA) subfractions of DOC. The properties of organic matter contributing to the release of DOC, HA and FA are, therefore, important for environmental risk assessment. In this study we have quantitatively measured the carbon speciation, and its relation with the leaching of Cu, in three fresh and carbonated MSWI bottom ash samples. Results show that up to only 25% of loss on ignition (LOI) consists of organic carbon (OC), while about 17% of OC in the three samples consists of HA and FA. Up to 50% of DOC in MSWI bottom ash leachates was identified as fulvic acid (FA). This value is substantially higher than previously estimated for these MSWI bottom ash samples and is consistent with the higher recovery of the new method that was applied. The results of this study imply that methods focusing on specific carbon fractions are more appropriate for assessment of environmentally relevant organic carbon species than the measurement of LOI.     

Estimated trichloroethene transformation rates due to naturally occurring biodegradation in a fractured rock aquifer

Rates of trichloroethene (TCE) mass transformed by naturally occurring biodegradation processes in a fractured rock aquifer underlying a former Naval Air Warfare Center (NAWC) site in West Trenton, New Jersey, were estimated. The methodology included (1) dividing the site into eight elements of equal size and vertically integrating observed concentrations of two daughter products of TCE biodegradation—cis‐dichloroethene (cis‐DCE) and chloride—using water chemistry data from a network of 88 observation wells; (2) summing the molar mass of cis‐DCE, the first biodegradation product of TCE, to provide a probable underestimate of reductive biodegradation of TCE, (3) summing the molar mass of chloride, the final product of chlorinated ethene degradation, to provide a probable overestimate of overall biodegradation. Finally, lower and higher estimates of aquifer porosities and groundwater residence times were used to estimate a range of overall transformation rates. The highest TCE transformation rates estimated using this procedure for the combined overburden and bedrock aquifers was 945 kg/yr, and the lowest was 37 kg/yr. However, hydrologic considerations suggest that approximately 100 to 500 kg/yr is the probable range for overall TCE transformation rates in this system. Estimated rates of TCE transformation were much higher in shallow overburden sediments (approximately 100 to 500 kg/yr) than in the deeper bedrock aquifer (approximately 20 to 0.15 kg/yr), which reflects the higher porosity and higher contaminant mass present in the overburden. By way of comparison, pump‐and‐treat operations at the NAWC site are estimated to have removed between 1,073 and 1,565 kg/yr of TCE between 1996 and 2009. © 2012 Wiley Periodicals, Inc.*