Kinetics of Hydrolytic Degradation of PLA

The chemical recycling of poly(lactic acid) (PLA) to its monomer is crucial to reduce both the consumption of renewable resources for the monomer synthesis and the environmental impact related to its production and disposal. In particular, the production of lactic acid from PLA wastes, rather than from virgin raw materials, it is also possible to achieve considerable primary energy savings. The focus of this work is to analyse deeply the PLA hydrolytic decomposition by means of a kinetic model based on two reactions mechanism. To this end, new experimental data have been gathered in order to investigate a wider temperature range (from 140 to 180 °C) and to extend the water/PLA ratio up to 50 % of PLA by weight. The reported results clearly highlight that more than 95 % of PLA is hydrolyzed to water-soluble lactic acid within 120 min, when it is hydrolyzed within 160–180 °C. Furthermore, the kinetic constant is highly influenced by reaction temperature. The proposed “two reactions” kinetic mechanism complies satisfactorily with the experimental data under analysis.     

Determination of the Burning Characteristics of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is characterized by three distinct processes, ignition, flame spread and burning rate. Although all three processes are important, ignition and burning rate are critical. The former, because it defines the potential to burn and the latter because of the inherent possibility of boilover. Burning rate is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil spill. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). Ignition has been studied to provide a tool that will serve to assess a fuels ease to ignite under conditions that are representative of oil spills. Two different techniques are used, piloted ignition when the fuel is exposed to a radiant heat flux and flash point as measured by the ASTM D56 Tag Closed Cup Test. Two different crude oils were used for these experiments, ANS and Cook Inlet. Crude oils were tested in their natural state and at different levels of weathering, showing that piloted ignition and flash point are strong functions of weathering level.     

Mechanism of Microbial Degradation of Slow-Release Fertilizers

Methyleneureas are condensation products of urea and formaldehyde of different molecular mass and solubility; they are used in large amounts both as resins, binders, and insulating materials for industrial applications, as well as a slow-release nitrogen fertilizer for greens, lawns, or in bioremediation processes. In the present study, the microbial breakdown of these products was investigated. The nitrogen was released as ammonia and urea, and the formaldehyde released immediately oxidized via formiate to carbon dioxide. The enzymatic mechanism of metabolization of methyleneureas was studied in microorganisms isolated from soil, which were able to use these compounds as the sole source of nitrogen for growth. A strain of the Gram-negative bacterium Ralstonia paucula (formerly Alcaligenes sp. CDC group IVc-2) completely degraded methylenediurea and dimethylenetriurea to urea, ammonia, formaldehyde, and carbon dioxide. The enzyme initiating this degradation (methylenediurease) was purified and turned out to be different from the previously described enzyme from Ochrobactrum anthropi with regard to its regulation of expression and physicobiochemical properties. Fungal degradation of methyleneureas may occur via the formation of organic acids, thus leading to a nonenzymatic degradation of methyleneureas, which are unstable under acidic conditions.     

Characterisation of the physico-mechanical parameters of MSW

Following the basics of soil mechanics, the physico-mechanical behaviour of municipal solid waste (MSW) can be defined through constitutive relationships which are expressed with respect to three physical parameters: the dry density, the porosity and the gravimetric liquid content. In order to take into account the complexity of MSW (grain size distribution and heterogeneity larger than for conventional soils), a special oedometer was designed to carry out laboratory experiments. This apparatus allowed a coupled measurement of physical parameters for MSW settlement under stress. The studied material was a typical sample of fresh MSW from a French landfill. The relevant physical parameters were measured using a gas pycnometer. Moreover, the compressibility of MSW was studied with respect to the initial gravimetric liquid content. Proposed methods to assess the set of three physical parameters allow a relevant understanding of the physico-mechanical behaviour of MSW under compression, specifically, the evolution of the limit liquid content. The present method can be extended to any type of MSW.     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

Pyrolysis of jute dust: effect of reaction parameters and analysis of products

Biowastes are becoming potential feedstocks for direct utilization or conversion to solid, liquid and gaseous fuels via various thermochemical routes. In this regard, jute dust which is a major agro-industrial waste in jute mills was pyrolysed in a fixed-bed reactor with an aim to study the product distribution and their characterization and to identify the optimum condition for bio-oil yield. The investigated process variables were temperature (400–700 °C), heating rate (10 and 40 °C/min) and nitrogen gas flow rate (50–250 ml/min). The yield of bio-oil is found to be maximum at 500 °C with a heating rate of 40 °C/min. However, further increase in temperature leads to decrease in bio-oil yield. Chemical compositions of the bio-oils were investigated using chromatographic and spectroscopic techniques such as ¹H NMR, FTIR and GC–MS. The heating value of the bio-oil is 26.71 MJ/kg. The study shows that jute dust have potential for conversion to bio-oil through the process of pyrolysis to supplement the petro-derived liquid fuel for heating and transportation applications after upgrading. The biochar produced as a co-product of jute dust pyrolysis can be a potential soil amendment with multiple benefits including increased soil fertility and C-sequestration.     

鼓泡式反应器高径比对氨法烟气脱碳性能的影响

以N2和CO2混合气模拟燃烧烟气，研究了鼓泡反应器的高径比以及反应条件对氨法烟气脱碳性能的影响。实验结果表明:在相同高径比的条件下，CO2吸收率随氨水质量分数的增加、反应温度的升高而逐渐增大，随进气CO2体积分数和模拟烟气流量的增加而逐渐减小;CO2吸收率随高径比的增加而增大，在高径比为3.98、氨水质量分数为28%、进气CO2体积分数为10%、模拟烟气流量为1.0L/min、反应温度为40℃的条件下，CO2吸收率最高可达100%。     

Fundamental study of the behavior of chlorine during the combustion of single RDF

A fundamental study of the combustion characteristics and the de-HCl behavior of a single refuse-derived fuel (RDF) pellet was carried out to explain the de-HCl phenomena of RDF during fluidized bed combustion and to provide data for the development of high efficiency power generation technology using RDF. In this research, combustion and pyrolysis experiments were carried out in an electrical furnace using a series of model and actual RDF samples. The de-HCl capability of Ca(OH)2 in RDF was evaluated by measuring the emission fraction of HCl in the flue gas and the capture fraction of Cl in the residue. It was found that the capture fraction of Cl components in the residue increased from 0 to nearly 70% when the molar ratio of Ca/Cl was changed from 0 to around 13. Apparently, the capture fraction also decreased with increasing oxygen concentration in the feed gas. The devolatilization process of RDF was confirmed to be a very important part of de-HCl process. The effect of temperature profile of the RDF pellet on the de-HCl process, as it varies with the heating rate of RDF and the oxygen concentration in the vicinity of the sample, is discussed.     

Estimation of future outflows of e-waste in India

The purpose of this study is to construct an approach and a methodology to estimate the future outflows of electronic waste (e-waste) in India. Consequently, the study utilizes a time-series multiple lifespan end-of-life model proposed by Peralta and Fontanos for estimating the current and future quantities of e-waste in India. The model estimates future e-waste generation quantities by modeling their usage and disposal. The present work considers two scenarios for the approximation of e-waste generation based on user preferences to store or to recycle the e-waste. This model will help formal recyclers in India to make strategic decisions in planning for appropriate recycling infrastructure and institutional capacity building. Also an extension of the model proposed by Peralta and Fontanos is developed with the objective of helping decision makers to conduct WEEE estimates under a variety of assumptions to suit their region of study. During 2007–2011, the total WEEE estimates will be around 2.5 million metric tons which include waste from personal computers (PC), television, refrigerators and washing machines. During the said period, the waste from PC will account for 30% of total units of WEEE generated.     

Biodegradability of a Selected Range of Polymers and Polymer Blends and Standard Methods for Assessment of Biodegradation

Synthetic polymers are important to the packaging industry but their use raises aesthetic and environmental concerns, particularly with regard to solid waste accumulation problems and the threat to wildlife. Some concerns are addressed by attention to problems associated with source reduction, incineration, recycling and landfill. Others are addressed by the development of new biodegradable polymers either alone or in blends. Materials used for biodegradable polymers include various forms of starch and products derived from it, biopolyesters and some synthetic polymers. Starch is rapidly metabolised and is an excellent base material for polymer blends or for infill of more environmentally inert polymers where it is metabolised to leave less residual polymer on biodegradation. This should help to improve the environmental impact of waste disposal. A number of standard methods have been developed to estimate the extent of biodegradability of polymers under various conditions and with a variety of organisms. They tend to be used mainly in the countries where they were developed but there is much overlap between the standards of different countries and wide scope for development of consistent and international standards.     

Formation of deposits on the surfaces of superheaters and economisers of MSW incinerator plants

Mineralogical and chemical investigations of deposits from superheaters and economisers from a MSWI plant in Mannheim, Germany, lead to a classification system which provides information about the most critical parameters leading to fouling and corrosion. With the help of this classification system parameters like the geometry of boilers and the waste input can be changed in order to prolong run times between revisions and enhance energy efficiency of MSWI plants.     

Evaluation of entanglement properties of crushed automobile shredded residue and detachment of entrapped particles

Automobile shredded residue is a potential solid fuel when its metal and chlorine-containing parts have been removed. The authors have investigated physical separation of automobile shredded residue to obtain the components that may be used in solid fuel and found that agglomerates of entangling fiber-like components are formed during crushing, making removal of metals and chlorine-containing parts difficult. In this paper, a reattachment ratio, entrapment ratio, and disentanglement ratio are proposed to evaluate the entanglement properties of crushed automobile shredded residue. It is found that products smaller than 16 mm were not reattached easily in the sieving process, and an index based on entanglement properties proposed here is useful to predict suitable crushing conditions. Wet detachment of entrapped particles from agglomerates of entangling materials was also applied to separate particulate matter from crushed ASR.     

Bio-Treatment of Natural Fibers in Isolation of Cellulose Nanofibres: Impact of Pre-Refining of Fibers on Bio-Treatment Efficiency and Nanofiber Yield

Biodegradability, renewability and high specific strength properties of cellulose nanofibres and microfibrils have made them very attractive in nano-biocomposite science. Treatment of natural fibers with suitable enzymes or fungus has been found to substantially alleviate the high energy requirement associated with the isolation of cellulose nanofibers via high shear refining and subsequent cryocrushing. This article briefly describes a novel enzymatic fiber pretreatment developed to facilitate the isolation of cellulose nanofibres and explores the effect of pre-refining of fibers on the effectiveness of bio-treatment. Soft wood Kraft pulp was pre-sheared to different degree and treated with a genetically modified fungus isolated from fungus infected Dutch elm tree. Cellulose nanofibres were isolated from these treated fibers by high shear refining. The percentage yield of nanofibres from pre-refined fibers in the less than 50 nm range showed a substantial increase and at the same time the number of revolutions required during the high shear refining to attain a comparable level of nanofibres isolation decreased. This observation may be attributed to the better fiber internal accessibility of the enzymes due to loosening up of the fibers and increased number of fiber ends as a result of pre-refining.     

Structure-biodegradation relationships of polymeric materials. 1. Effect of degree of oxidation on biodegradability of carbohydrate polymers

The biodegradability of oxidized starch and inulin has been studied in relation to the degree of periodate oxidation to dialdehyde derivatives, by measuring oxygen consumption and mineralization to carbon dioxide. A higher degree of oxidation of dialdehyde starch and dialdchyde inulin results in a lower rate at which the polymers are biodegraded. It is demonstrated that the biodegradation rate of dialdehyde inulin derivatives decreases more than that of equivalent starch derivatives. The differences in biodegradation behavior between dialdehyde starch and dialdehyde inulin, resulting from comparable modifications, are discussed in terms of conformational structure.     

Economic aspects of the rehabilitation of the Hiriya landfill

The Hiriya landfill, Israel's largest, operated from 1952 to 1998. The landfill, located in the heart of the Dan Region, developed over the years into a major landscape nuisance and environmental hazard. In 1998, the Israeli government decided to close the landfill, and in 2001 rehabilitation activities began at the site, including site investigations, engineering and scientific evaluations, and end-use planning. The purpose of the present research is to perform a cost-benefit analysis of engineering and architectural-landscape rehabilitation projects considered for the site. An engineering rehabilitation project is required for the reduction of environmental impacts such as greenhouse gas emissions, slope instability and leachate formation. An architectural-landscape rehabilitation project would consider improvements to the site to make it suitable for future end uses such as a public park. The findings reveal that reclamation is worthwhile only in the case of architectural-landscape rehabilitation of the landfill, converting it into a public park. Engineering rehabilitation alone was found to be unjustified, but is essential to enable the development of a public park.     

Effect of Degree of Substitution of Octenyl Succinate Starch on Enzymatic Degradation

Octenyl succinate starch of degree of substitution (ds) 0.03, 0.07, and 0.11 was synthesized in an aqueous medium. These compounds were then tested for the susceptibility to enzymatic degradation. The multiple-enzyme regime of -amylase, amyloglucosidase, and pullulanase was chosen for the evaluation. This combination of enzymes had been proven to degrade 99.5% of unmodified starch to glucose and hence was chosen for this study. It was found that even small amounts of subsituent caused a considerable decrease in the extent of degradation. The net extent of degradation decreased with increasing ds. Surprisingly, the amount of glucose from all three substituted substrates was quite similar, suggesting the effect small amounts of subtituent had on the enzymatic activity.     

A review of emerging technologies for remediation of PFASs

The need for remediation of poly‐ and perfluoroalkyl substances (PFASs) is growing as a result of more regulatory attention to this new class of contaminants with diminishing water quality standards being promulgated, commonly in the parts per trillion range. PFASs comprise >3,000 individual compounds, but the focus of analyses and regulations has generally been PFASs termed perfluoroalkyl acids (PFAAs), which are all extremely persistent, can be highly mobile, and are increasingly being reported to bioaccumulate, with understanding of their toxicology evolving. However, there are thousands of polyfluorinated “PFAA precursors”, which can transform in the environment and in higher organisms to create PFAAs as persistent daughter products. Some PFASs can travel miles from their point of release, as they are mobile and persistent, potentially creating large plumes. The use of a conceptual site model (CSM) to define risks posed by specific PFASs to potential receptors is considered essential. Granular activated carbon (GAC) is commonly used as part of interim remedial measures to treat PFASs present in water. Many alternative treatment technologies are being adapted for PFASs or ingenious solutions developed. The diversity of PFASs commonly associated with use of multiple PFASs in commercial products is not commonly assessed. Remedial technologies, which are adsorptive or destructive, are considered for both soils and waters with challenges to their commercial application outlined. Biological approaches to treat PFASs report biotransformation which creates persistent PFAAs, no PFASs can biodegrade. Water treatment technologies applied ex situ could be used in a treatment train approach, for example, to concentrate PFASs and then destroy them on‐site. Dynamic groundwater recirculation can greatly enhance contaminant mass removal via groundwater pumping. This review of technologies for remediation of PFASs describes that:

• GAC may be effective for removal of long‐chain PFAAs, but does not perform well on short‐chain PFAAs and its use for removal of precursors is reported to be less effective;
• Anion‐exchange resins can remove a wider array of long‐ and short‐chain PFAAs, but struggle to treat the shortest chain PFAAs and removal of most PFAA precursors has not been evaluated;
• Ozofractionation has been applied for PFASs at full scale and shown to be effective for removal of total PFASs;
• Chemical oxidation has been demonstrated to be potentially applicable for some PFAAs, but when applied in situ there is concern over the formation of shorter chain PFAAs and ongoing rebound from sorbed precursors;
• Electrochemical oxidation is evolving as a destructive technology for many PFASs, but can create undesirable by‐products such as perchlorate and bromate;
• Sonolysis has been demonstrated as a potential destructive technology in the laboratory but there are significant challenges when considering scale up;
• Soils stabilization approaches are evolving and have been used at full scale but performance need to be assessed using appropriate testing regimes;
• Thermal technologies to treat PFAS‐impacted soils show promise but elevated temperatures (potentially >500 °C) may be required for treatment.

There are a plethora of technologies evolving to manage PFASs but development is in its early stage, so there are opportunities for much ingenuity.     

Quick monitoring of pozzolanic reactivity of waste ashes

This article proposes a quick method of monitoring for pozzolanic reactivity of waste ashes by investigating the electrical conductivity of the suspension at an elevated temperature. This suspension is obtained by mixing tested pozzolan with an ordinary Portland cement (OPC) solution produced by mixing ordinary Portland cement with water. For comparison, silica fume, metakaolin, rice husk ash and river sand – whose pozzolanic reactivities range from reactive to inert – were used in the experimental investigation. The electrical conductivity of the suspension was continually recorded by using an electrical conductivity meter and stored by using a personal computer for a period of slightly over 1 day. The indicative parameters that can be related to pozzolanic reactivity were discussed and analyzed in detail. It was found that it is possible to determine the pozzolanic reactivity of fly ash within 28 h by using the proposed technique, as compared to 7 or 28 days for the determination of strength activity index according to ASTM. This technique would help concrete technologists to speedily investigate the quality of fly ash for use as a cement replacement in order to alleviate pollution caused by cement production and solve disposal problems of waste ashes.     

物化性质对细颗粒长大过程影响的研究现状

燃煤产生的飞灰颗粒是除尘器去除的主体，研究颗粒的物化性质对提高除尘效率有重要的意义。燃煤产生的细颗粒不能被传统除尘器有效的脱除，颗粒长大技术是有效脱除燃煤细颗粒的一种除尘技术。针对颗粒长大技术，综述了细颗粒的物化性质对脱除效果的影响。     

Influence of distance on the motivation and frequency of household recycling

People choose to participate in recycling for a variety of reasons. This study analyzes the relationship between the frequency of selective separation and general refuse disposal, and the influence on the recycling habit of the walking distance to drop off the materials. The methodology employed was one of personal interviews in the street, the study population being a region in the north of Spain (Principality of Asturias). More than one thousand people participated in this survey carried out in 2002. Five hypotheses related to three variables (the frequency for depositing recycling materials and general refuse, the distance to recycling and general bins, and the recycling habit) were tested using different statistical tests. Results show that the people who frequently go to the bins to dispose of general refuse are more likely to recycle some product at home, and in most cases, as the distance to the recycling bins decreases, the number of fractions that citizens separate and collect at home increases. Most of the results obtained have been compared with other previous in literature.