Effects of planned expansion of waste incineration in the Swedish district heating systems

Recent targets for reduced amounts of waste to landfills in Sweden will result in a large increase in waste incineration with recovery of energy, used primarily for district heating. The aim of this study is to investigate what changes in the usage of other fuels and technologies for district heat production would be caused by this increase. A questionnaire was sent out to the largest district heating companies, and simulations in an energy systems model were carried out. The analysis shows that increased waste incineration reduces the demand for other fuels, especially biomass, for district heat production. The effects include reductions in operating hours as well as the avoidance or postponement of investments in new plants for district heat production. Increased waste incineration will also lead to a greater use of district heating in Sweden.     

From exogenous to endogenous development in Scottish forestry: the feasibility of small-scale wood energy enterprise

This paper presents a change in the Scottish forestry policy from the exogenous to the endogenous development approach, and feasibility of heat entrepreneurship based on locally produced woodfuels in the Highlands of Scotland. The cost structure and heat pricing in the case of an 800 kW solid fuel boiler is presented, and the profitability of local heat entrepreneurship is analysed with scenarios of different investment costs and fuel prices. The results indicate that a district heating (DH) system, using locally produced woodchips, could produce heat at a lower price than single-house heating systems using light fuel oil. The profitability of replacing existing heating units by investing in a new district heating (DH) scheme is very dependent on the available investment support, price level of woodchips and substituted light fuel oil, and the amount of sold energy. In the case of an 800 kW DH scheme, and woodchip prices of 14 and 22 €/MWh, investments should remain under break-even points of 280 and 420 €/kW of heating power (230,000–335,000€).     

Drying of granulated wood ash by flue gas from saw dust and natural gas combustion

At the district heating plant of Kalmar, Sweden an on-line unit for production of granulated wood ash for nutrient recycling on forest soils is being applied. Currently, the granules are dried by hot air from an oil-fired burner. The objective of this work was to investigate how drying by flue gas affects the hardening of granules, or impacts their chemical composition and properties. Ninety-six granule samples were treated by flue gas from natural gas combustion in a laboratory pilot scale flue gas generator. CO₂, CO, O₂, C₃H₈ and NO concentrations were varied during the experiment. Additionally, some samples were treated by flue gas from combustion of sawdust at the heating plant in Kalmar. Drying by flue gases did not affect the chemical composition of granules, but minor effects were seen in their mineralogy. The carbonate content was slightly higher in granules treated with flue gas from natural gas combustion compared to the granules dried by hot air only, when measured by wet chemical methods. Results from XRD analysis imply that the calcite content is higher and the portlandite and arcanite content slightly less in granules treated with flue gas from sawdust combustion compared to the granules dried by hot air only. The results from this investigation showed no negative effects on ash granule composition or physical structure by the use of a flue as a drying medium.     

Energy and exergy analysis of a heat storage tank with a novel eutectic phase change material layer of a solar heater system

Solar energy is one of the most important renewable energy sources, but it is not available every time and every season. Thus, storing of solar energy is important. One of the popular methods of heat storage is use of phase change materials (PCMs) which have large thermal energy storage capacity. In this study, the heat storage tank in a domestic solar water heating system was chosen as control volume. The experiments were performed in the province of Elaz?g, Turkey, in November when solar radiation was weak due to cloudy sky. The heat storage tank of the system was modified to fill PCM between insulation and hot water part. A few PCMs which are Potassium Fluoride, Lithium Metaborate Dihydrate, Strontium Hydroxide Octahydrate, Barium Hydroxide Octahydrate, Aluminum Ammonium Sulfate, and Sodium Hydrogen Phosphate were analyzed to proper operating conditions using a Differential Scanning Calorimeter (DSC) and the best PCM was obtained with the Aluminum Ammonium Sulfate and Sodium Hydrogen Phosphate mixture. Thus, eutectic PCM was obtained and used in a heat storage tank of the solar water heating system. Energy and exergy analysis of heat storage tank was performed with and without the PCM. Energy and exergy analysis has shown that the heat storage tank with the PCM is more efficient than without the PCM and the maximum exergy efficiency was obtained as 22% with the heat storage tank with the PCM.     

Performance analysis of different orc power plant configurations using solar and geothermal heat sources

ABSTRACT

Energy optimization is performed on hybrid solar-geothermal power plant working according to Organic Rankine Cycle and installed in southern Tunisia. The performances of four different configurations of the power plant are studied. Mass and energy balances are established for the different compounds. The effects of the main operating parameters such as the geothermal water temperature, ambient temperature and direct normal irradiation on the power plant performances are analyzed. A code is established using Engineering Equation Solver software (EES) to perform the required calculations. Obtained results show that the hybrid solar-geothermal power plant with a heat recovery system is the most suitable configuration design giving a better overall energy efficiency of 15.77 and13.11% and a maximum net power of 1089 and 1882 kW in winter and summer, respectively. However, in the summer season, using a heat recovery system can valuable only when the water temperature is higher than 66°C. For air-cooled condenser, the suitable condensing pressure is 1 bar in winter and 1.9 bars in summer.     

Modeling of Low Temperature Geothermal District Heating Systems

Abstract

In this work, low temperature geothermal district heating systems with heat pumps have been studied and compared with fuel-oil boiler heating systems for intermittent and continuous regimes according to the optimum indoor air temperature and operational cost. Izmir Institute of Technology (IZTECH) Campus is taken as a case study. Various heat pump and boiler configurations are studied to meet required duty. Operational cost analysis for each alternative is conducted. According to the results, for IZTECH Campus the best alternative, which gives the optimum indoor air temperature and the lowest operational cost, is heat pump continuous regime.     

Potential of solar domestic hot water systems in rural areas for greenhouse gas emission reduction in Poland

Application of solar energy for preparing domestic hot water is one of the easiest methods of utilization of this energy. At least part of the needs for warm tap water could be covered by solar systems. At present, mainly coal is used for water heating at dwellings in rural areas in Poland. Warm tap water consumption will increase significantly in the future as standards of living are improved. This can result in the growth of electricity use and an increase in primary fuel consumption. Present and future methods of warm sanitary water generation in rural areas in Poland is discussed, and associated greenhouse gas (GHG) emissions are estimated. It is predicted that the emission of CO₂ and NOx will increase. The emission of CO and CH₄ will decrease because of changes in the structure of the final energy carriers used. The economic and market potentials of solar energy for preparing warm water in rural areas are discussed. It is estimated that solar systems can meet 30%–45% of the energy demand for warm water generation in rural areas at a reasonable cost, with a corresponding CO₂ emission reduction. The rate of realization of the economic potential of solar water heaters depends on subsidies for the installation of equipment.

     

Photovoltaic-thermal (PV/t) panel to minimize electrical and air conditioning energy consumption of a typical office in Beirut

A combined photovoltaic–thermal (PV/t) panel is proposed to produce simultaneously electricity and heat from one integrated unit. The unit utilizes effectively the solar energy through achieving higher PV electrical efficiency and using the thermal energy for heating applications. To predict the performance of the PV/t at a given environmental conditions, a transient mathematical model was developed. The model was integrated in a heating application for a typical office space in the city of Beirut to provide the office needs for electricity, heating during winter season, and dehumidification and evaporative cooling during the summer season. To minimize the yearly office energy (electrical and heat) needs, the PV/t panel cooling air flow rate and the dehumidification regeneration temperature were determined for opimal unit operation. Thermal energy savings of up to 85% in winter and 71% in summer were achived compared to conventional systems at a payback period of 8 years for the panels.     

District heating and ambivalent energy transition paths in urban and rural contexts

ABSTRACT

Most institutions and industrial actors believe that district heating infrastructure can play a key role in accelerating the transition to low-carbon energy systems. In this article we test this belief in Italy, starting from a census of all existing plants, subdivided by sources of supply and business organization models. We isolate two types of district heating (urban and rural) and find that they are different with respect to their approaches to energy transition. In rural areas, networks constitute systems that can empower the local techno-institutional complex to achieve a technological leap. Set in a pre-existing social network, district heating reinforces a sense of community and facilitates the involvement of various local players in a collective project. In the case of biomass, we are faced with local systems that have almost completed the transition with regard to the production of thermal and sometimes electric energy. In urban areas, on the other hand, networks represent functional devices for the stabilization of the techno-institutional complex. They allow cities to work on the circularity of some economies, generating added value from the same factors of production. The discrepancy between urban and rural contexts thus highlights the need to consider the ambivalence of district heating technology.     

Numerical parametric study of a new earth-air heat exchanger configuration designed for hot and arid climates

ABSTRACT

Thermal potential for cooling and heating can be achieved by new configuration of earth–air heat exchanger (EAHE). This paper presents a numerical investigation of thermal performance of a spiral-shaped configuration of EAHE intended for the summer cooling in hot and arid regions of Algeria. A commercial finite volume software (ANSYS FLUENT) has been used to carry out the transient three-dimensional simulations and the obtained results have been validated using the experimental and numerical data obtained from the literature. The agreement between our simulation results and those from literature is very satisfactory. A parametric analysis of the new geometry of (EAHE) has been performed to investigate the effect of pitch, depth, pipe length and of the flow velocity on the outlet air temperature and the EAHE’s mean efficiency as well as its coefficient of performance (COP). It has been shown that when the pitch space varies between 0.2 and 2 m the difference of outlet air temperature increases by 6 ^°C. When the air velocity increases from 2 to 5 m/s the mean efficiency decreases from 60 % to 33 % and the COP of the EAHE decreases from 2.84 to 0.46.     

Comparative study on performances of a heat-pipe PV/T system and a heat-pipe solar water heating system

The heat-pipe solar water heating (HP-SWH) system and the heat-pipe photovoltaic/thermal (HP-PV/T) system are two practical solar systems, both of which use heat pipes to transfer heat. By selecting appropriate working fluid of the heat-pipes, these systems can be used in the cold region without being frozen. However, performances of these two solar systems are different because the HP-PV/T system can simultaneously provide electricity and heat, whereas the HP-SWH system provides heat only. In order to understand these two systems, this work presents a mathematical model for each system to study their one-day and annual performances. One-day simulation results showed that the HP-SWH system obtained more thermal energy and total energy than the HP-PV/T system while the HP-PV/T system achieved higher exergy efficiency than the HP-SWH system. Annual simulation results indicated that the HP-SWH system can heat the water to the available temperature (45°C) solely by solar energy for more than 121 days per year in typical climate regions of China, Hong Kong, Lhasa, and Beijing, while the HP-PV/T system can only work for not more than 102 days. The HP-PV/T system, however, can provide an additional electricity output of 73.019 kWh/m², 129.472 kWh/m², and 90.309 kWh/m² per unit collector area in the three regions, respectively.     

Hybrid input-output analysis to evaluate economic impacts of biomass energy

ABSTRACT

The introduction of the new biomass industry exerts influences that change the interactions among economic sectors by drawing the resources for generating electricity, pricing alterations from the existing market and competitively selling electricity to the power grid. These influences should be described and identified to ensure the benefits to the local economy. In this article, we deem to test the potential of hybrid I-O analysis to analyze the economic impacts and address the change in characteristics of the economic impacts of the biomass power plant. The resource utilization data from the existing biomass power plant located in Kochi Prefecture (Japan) is collected and then analyzed by a hybrid input-output (I-O) analysis. We found that (1) the use of cutoff function could determine the new economy’s structure included the biomass power plant where the allocation of resource in the economy is changed according to the consumption and production of the biomass power plant, (2) The power plant increases the total production of Kochi prefecture’s economy, and this benefit overthrows the negative effect of the loss of resource demand of the existing economic sectors. The use of the hybrid I-O to forecast the economic impacts on the local economy could enhance the decision made by the policymaker.     

Novel Temperature Control Technique for a Medicinal Herb Dryer System Powered by a Photovoltaic Array

Each plant has its own optimal drying temperature, especially for the medicinal herbs, because they are sensitive to heat. If the drying temperature becomes more than the optimal value, some chemical reactions will occur and influence the quality of the dried herb, such as color, taste, and aroma. While if the drying temperature becomes lower than the optimal value, the drying process will slow down, and consequently an expected degradation in the quality of the herb may occur, due to insects and fungi infestation which increase in moist conditions. This paper presents a new temperature control technique for a medicinal herb dryer system. The technique fixes the drying temperature of the medicinal herbs at 40^°C, even in cases of rapidly changing atmospheric conditions. The control of the dryer temperature is achieved through using the proportional integral (PI) controller. The designed dryer contains two systems, which are the thermal and the electrical systems. The thermal system is designed to heat the drying air by using solar energy and bio-gas fuel. Whereas the electrical system, which contains a photovoltaic (PV) modules and a battery, is designed to supply the different electrical loads of the dryer system. The control technique is investigated through simulation work by using MATLAB-SIMULINK. The simulation results indicate the high capability of the proposed technique in controlling the drying temperature, even in cases of rapidly changing atmospheric conditions.     

太阳能技术在新疆油田的应用研究

以新疆地区太阳能开发优越的自然条件分析为基础,介绍了太阳能发电抽油机技术、供热水的应用,以及太阳能发电供热水的技术原理、系统构成、重要技术参数等。通过实际应用,解析了太阳能利用中最关键的经济效益和节能减排效益两方面的问题,并通过与常规燃煤火力发电技术的对比分析,证明了太阳能发电供热的技术优越性。太阳能发电供热的大规模推广应用,对响应国家节能减排政策,提高油田的节能减排效益和经济效益,创建绿色油气田具有深远的意义。     

Local or global food markets: A comparison of energy use for transport

Abstract

This study compares energy use for food transport to a farmers' market in Sweden with energy use for transport in the conventional food system. The farmers' market was investigated through data sampling from on-site investigations. The conventional food system was studied with the aid of life cycle assessments reported in the literature. Overall, the study found no significant differences in levels of energy use for transport to the farmers' market compared with the conventional food system. For certain products, such as fresh fruits and vegetables, transport-related energy use was much lower in the local system although the season in Sweden for this kind of product is restricted to two or three months at the end of the summer. However, there is considerable potential to increase energy efficiency in local food systems by organizing the selling in new ways and by using more energy efficient vehicles.     

Exergy and economic analysis of organic Rankine cycle hybrid system utilizing biogas and solar energy in rural area of China

Due to the existing huge biogas resource in the rural area of China, biogas is widely used for production and living. Cogeneration system provides an opportunity to realize the balanced utilization of the renewable energy such as biogas and solar energy. This article presented a numerical investigation of a hybrid energy-driven organic Rankine cycle (ORC) cogeneration system, involving a solar ORC and a biogas boiler. The biogas boiler with a module of solar parabolic trough collectors (PTCs) is employed to provide heat source to the ORC via two distinct intermediate pressurized circuits. The cogeneration supplied the power to the air-condition in summer condition and hot water, which is heated in the condenser, in winter condition. The system performance under the subcritical pressures has been assessed according to the energy–exergy and economic analysis with the organic working fluid R123. The effects of various parameters such as the evaporation and condensation temperatures on system performance were investigated. The net power generation efficiency of the cogeneration system is 11.17%, which is 25.8% higher than that of the base system at an evaporation temperature 110°C. The exergy efficiency of ORC system increases from 35.2% to 38.2%. Moreover, an economic analysis of the system is carried out. The results demonstrate that the profits generated from the reduction of biogas fuel and electricity consumption can lead to a significant saving, resulting in an approximate annual saving from $1,700 to $3,000. Finally, a case study based on the consideration of typical rural residence was performed, which needs a payback period of 7.8 years under the best case.     

LUMP SUM TAX LOSS REIMBURSEMENT UNDER THE THAMES RIVER FLOOD CONTROL COMPACT1

ABSTRACT: Under the terms of the Thames River Valley Flood Control Compact, Connecticut has been paying Massachusetts 40 percent of the annual property tax losses suffered by seven Massachusetts towns where four flood control structures were located. The permissable alternative of a single lump sum payment was investigated in the study summarized here. The lump sum payment should be the proportion of total benefits (flood control and recreation) from the four structures which Connecticut receives, multiplied by the present value of projected tax losses in the seven tom Flood control benefits and their distribution between the two states were fixed in the Compact, but a survey was necessary to determine recreational benefits and their distribution. Regression analysis of 1957 to 1978 tax loss data provided equations used to project future tax losses. Resent values of projected tax low were calculated using discount rates ranging from 6 to 12 percent. A plausible range of lump sum reinbursements as of 1979 was identified.     

Heat loss analysis: An approach toward the revival of parabolic dish type solar cooker

Present work investigates a noble approach toward the heat loss analysis of parabolic dish type solar cooker. Various experiments have been done on cooking pot to get the input parameter for calculation purposes. Cooking pot was kept at the focus of a parabolic dish type concentrator and repeated experiments have been done to measure solar radiation intensity (direct and Indirect) using a pyrometer, temperature at the focus of parabolic dish using a thermocouple and air velocity using hot wire anemometer to investigate the heat losses from the cooking pot. In the present article, a numerical approach has been performed to define the new parameter called performance index of the cooking pot which decides how the useful energy of working fluid inside the cooking pot approaches concentration ratio of the parabolic dish type solar cooker. The present analysis shows that the performance index varies from 15.45 to 17.66 and efficiency varies from 85.83% to 98.10% with the time of the day.     

Performance of a small-scale solar-powered adsorption cooling system

In this study, an experimental investigation on the performance of a small-scale residential-size solar-driven adsorption (silica gel-water) cooling system that was constructed at Assiut University campus, Egypt is carried out. As Assiut area is considered as hot, arid climate, field tests for performance assessment of the system operation during the summer season are performed under different environmental operating conditions. The system consists of an evacuated tube with a reflective concentration parabolic surface solar-collector field with a total area of 36 m², a silica gel-water adsorption chiller of 8 kW nominal cooling capacity, and hot and cold water thermal storage tanks of 1.8 and 1.2 m³ in volume, respectively. The results of summer season field test show that under daily solar insolation varying from 21 to 27 MJ/m², the solar collectors employed in the system had high and almost constant thermal efficiency. The daily solar-collector efficiency during the period of system operation ranged from about 50% to 78%. The adsorption chiller performance shows that the chiller average daily coefficient of performance (COP) was 0.41 with the average cooling capacity of 4.4 kW when the cooling-water and chilled-water temperatures were about 31°C and 19°C, respectively. As the chiller cooling water is cooled by the cooling tower in the hot arid area, the cooling water is at a higher temperature than the design point of the chiller. Therefore, an experiment was carried out using the city water for cooling. The results show that an enhancement in the chiller COP by 40% and the chilling power by 17% has been achieved when the city water was 27.7°C.     

Commercial Medicinal Plant Extraction in the Hills of Nepal: Local Management System and Ecological Sustainability

This paper presents a case study from Jumla District, Nepal, investigating local management systems and ecological sustainability of commercial collection of a medicinal plant, spikenard (Nardostachys grandiflora DC, Valerianaceae), growing in alpine meadows. Interviews were undertaken with local collectors, traders, and district forest office staff, and the dynamics of people–plant interactions are analyzed using the Oakerson model. In all, 110 sample plots 1m square were laid out in three areas with differing collection and grazing pressures for recording of floristic composition and abundance of spikenard root biomass. Comparisons show significantly more root biomass in uncollected than collected areas with local management and the interpretation of differences in abundance is discussed. The combination of qualitative and quantitative investigations can provide a framework for the study of people–plant interactions, and this study can serve as first step in a compilation of cases to create a more detailed picture of local management systems of Nepali nontimber forest products in general and commercially collected medicinal and aromatic plants in particular.